Abstract: Monitoring the tool flank wear without affecting the
throughput is considered as the prudent method in production
technology. The examination has to be done without affecting the
machining process. In this paper we proposed a novel work that is
used to determine tool flank wear by observing the sound signals
emitted during the turning process. The work-piece material we used
here is steel and aluminum and the cutting insert was carbide
material. Two different cutting speeds were used in this work. The
feed rate and the cutting depth were constant whereas the flank wear
was a variable. The emitted sound signal of a fresh tool (0 mm flank
wear) a slightly worn tool (0.2 -0.25 mm flank wear) and a severely
worn tool (0.4mm and above flank wear) during turning process were
recorded separately using a high sensitive microphone. Analysis
using Singular Value Decomposition was done on these sound
signals to extract the feature sound components. Observation of the
results showed that an increase in tool flank wear correlates with an
increase in the values of SVD features produced out of the sound
signals for both the materials. Hence it can be concluded that wear
monitoring of tool flank during turning process using SVD features
with the Fuzzy C means classification on the emitted sound signal is
a potential and relatively simple method.
Abstract: A numerical investigation of surface heat transfer
characteristics of turbulent air flows in different parallel plate
grooved channels is performed using CFD code. The results are
obtained for Reynolds number ranging from 10,000 to 30,000 and for
arc-shaped and rectangular grooved channels. The influence of
different geometric parameters of dimples as well as the number of
them and the geometric and thermophysical properties of channel
walls are studied. It is found that there exists an optimum value for
depth of dimples in which the largest wall heat flux can be achieved.
Also, the results show a critical value for the ratio of wall thermal
conductivity to the one of fluid in which the dependence of wall heat
flux to this ratio almost vanishes. In most cases examined, heat
transfer enhancement is larger for arc-shaped grooved channels than
rectangular ones.
Abstract: The objective of the research was to evaluate the
quality of milk pomade sweet – sherbet packed in different packaging
materials (Multibarrier 60, met.BOPET/PE, Aluthen), by several
packaging technologies – active and modified atmosphere (MAP)
(consisting of 100% CO2), and control – in air ambiance.
Experiments were carried out at the Faculty of Food Technology of
Latvia University of Agriculture. Samples were stored at the room
temperature +21±1 °C. The physiochemical properties – weight
losses, moisture, hardening, colour and changes in headspace
atmosphere concentration (CO2 and O2) of packs were analysed
before packaging and after 2, 4, 6, 8, 10 and 12 storage weeks.
Abstract: In order to study the effect of plant density and
competition of wheat with field bindweed (Convolvulus arvensis) on
yield and agronomical properties of wheat(Triticum Sativum) in
irrigated conditions, a factorial experiment as the base of complete
randomize block design in three replication was conducted at the
field of Kamalvand in khoramabad (Lorestan) region of Iran during
2008-2009. Three plant density (Factor A=200, 230 and 260kg/ha)
three cultivar (Factor B=Bahar,Pishtaz and Alvand) and weed control
(Factor C= control and no control of weeds)were assigned in
experiment. Results show that: Plant density had significant effect
(statistically) on seed yield, 1000 seed weight, weed density and dry
weight of weeds, seed yield and harvest index had been meaningful
effect for cultivars. The interaction between plant density and
cultivars for weed density, seed yield, thousand seed weight and
harvest index were significant. 260 kg/ha (plant density) of wheat had
more effect on increasing of seed yield in Bahar cultivar wheat in
khoramabad region of Iran.
Abstract: Safety, river environment, and sediment utilization are the elements of the target of sediment management. As a change in an element by sediment management, may affect the other two elements, and the priority among three elements depends on stakeholders. It is necessary to develop a method to evaluate the effect of sediment management on each element and an integrated evaluation method for socio-economic effect. In this study, taking Mount Merapi basin as an investigation field, the method for an active volcanic basin was developed. An integrated evaluation method for sediment management was discussed from a socio-economic point on safety, environment, and sediment utilization and a case study of sediment management was evaluated by means of this method. To evaluate the effect of sediment management, some parameters on safety, utilization, and environment have been introduced. From a utilization point of view, job opportunity, additional income of local people, and tax income to local government were used to evaluate the effectiveness of sediment management. The risk degree of river infrastructure was used to describe the effect of sediment management on a safety aspect. To evaluate the effects of sediment management on environment, the mean diameter of grain size distribution of riverbed surface was used. On the coordinate system designating these elements, the direction of change in basin condition by sediment management can be predicted, so that the most preferable sediment management can be decided. The results indicate that the cases of sediment management tend to give the negative impacts on sediment utilization. However, these sediment managements will give positive impacts on safety and environment condition. Evaluation result from a social-economic point of view shows that the case study of sediment management reduces job opportunity and additional income for inhabitants as well as tax income for government. Therefore, it is necessary to make another policy for creating job opportunity for inhabitants to support these sediment managements.
Abstract: In this work we investigated the behavior of methane
hydrates dispersed in crude oils from different fields at temperatures
below 0°C. In case of crude oil emulsion the size of water droplets is
in the range of 50e100"m. The size of hydrate particles formed from
droplets is the same. The self-preservation is not expected in this
field. However, the self-preservation of hydrates with the size of
particles 24±18"m (electron microscopy data) in suspensions is
observed. Similar results were obtained for four different kinds of
crude oil and model system such as asphaltenes, resins and wax in ndecane.
This result can allow developing effective methods to prevent
the formation and elimination of gas-hydrate plugs in pipelines under
low temperature conditions (e. g. in Eastern Siberia). There is a
prospective to use experiment results for working out the technology
of associated petroleum gas recovery.
Abstract: This paper considers a scheduling problem in flexible
flow shops environment with the aim of minimizing two important
criteria including makespan and cumulative tardiness of jobs. Since
the proposed problem is known as an Np-hard problem in literature,
we have to develop a meta-heuristic to solve it. We considered
general structure of Genetic Algorithm (GA) and developed a new
version of that based on Data Envelopment Analysis (DEA). Two
objective functions assumed as two different inputs for each Decision
Making Unit (DMU). In this paper we focused on efficiency score of
DMUs and efficient frontier concept in DEA technique. After
introducing the method we defined two different scenarios with
considering two types of mutation operator. Also we provided an
experimental design with some computational results to show the
performance of algorithm. The results show that the algorithm
implements in a reasonable time.
Abstract: This paper demonstrates a model of an e-Learning
system based on nowadays learning theory and distant education
practice. The relationships in the model are designed to be simple
and functional and do not necessarily represent any particular e-
Learning environments. It is meant to be a generic e-Learning
system model with implications for any distant education course
instructional design. It allows online instructors to move away from
the discrepancy between the courses and body of knowledge. The
interrelationships of four primary sectors that are at the e-Learning
system are presented in this paper. This integrated model includes
[1] pedagogy, [2] technology, [3] teaching, and [4] learning. There
are interactions within each of these sectors depicted by system loop
map.
Abstract: Technology assessment is a vital part of decision process in manufacturing, particularly for decisions on selection of new sustainable manufacturing processes. To assess these processes, a matrix approach is introduced and sustainability assessment models are developed. Case studies show that the matrix-based approach provides a flexible and practical way for sustainability evaluation of new manufacturing technologies such as those used in surface coating. The technology assessment of coating processes reveals that compared with powder coating, the sol-gel coating can deliver better technical, economical and environmental sustainability with respect to the selected sustainability evaluation criteria for a decorative coating application of car wheels.
Abstract: Image retrieval is a topic where scientific interest is currently high. The important steps associated with image retrieval system are the extraction of discriminative features and a feasible similarity metric for retrieving the database images that are similar in content with the search image. Gabor filtering is a widely adopted technique for feature extraction from the texture images. The recently proposed sparsity promoting l1-norm minimization technique finds the sparsest solution of an under-determined system of linear equations. In the present paper, the l1-norm minimization technique as a similarity metric is used in image retrieval. It is demonstrated through simulation results that the l1-norm minimization technique provides a promising alternative to existing similarity metrics. In particular, the cases where the l1-norm minimization technique works better than the Euclidean distance metric are singled out.
Abstract: A Laboratory-scale packed bed reactor with microbial
cellulose as the biofilm carrier was used to investigate the
denitrification of high-strength nitrate wastewater with specific
emphasis on the effect the nitrogen loading rate and hydraulic
retention time. Ethanol was added as a carbon source for
denitrification. As a result of this investigation, it was found that up
to 500 mg/l feed nitrate concentration the present system is able to
produce an effluent with nitrate content below 10 ppm at 3 h
hydraulic retention time. The highest observed denitrification rate
was 4.57 kg NO3-N/ (m3 .d) at a nitrate load of 5.64 kg NO3-
N/(m3 .d), and removal efficiencies higher than 90% were obtained
for loads up to 4.2 kg NO3-N/(m3 .d). A mass relation between COD
consumed and NO3-N removed around 2.82 was observed. This
continuous-flow bioreactor proved an efficient denitrification system
with a relatively low retention time.
Abstract: The objective of this manuscript is to find area under the plasma concentration- time curve (AUC) for multiple doses of salbutamol sulphate sustained release tablets (Ventolin® oral tablets SR 8 mg, GSK, Pakistan) in the group of 18 healthy adults by using computational mathematics techniques. Following the administration of 4 doses of Ventolin® tablets 12 hourly to 24 healthy human subjects and bioanalysis of obtained plasma samples, plasma drug concentration-time profile was constructed. AUC, an important pharmacokinetic parameter, was measured using integrated equation of multiple oral dose regimens. The approximated AUC was also calculated by using computational mathematics techniques such as repeated rectangular, repeated trapezium and repeated Simpson's rule and compared with exact value of AUC calculated by using integrated equation of multiple oral dose regimens to find best computational mathematics method that gives AUC values closest to exact. The exact values of AUC for four consecutive doses of Ventolin® oral tablets were 150.5819473, 157.8131756, 164.4178231 and 162.78 ng.h/ml while the closest values approximated AUC values were 149.245962, 157.336171, 164.2585768 and 162.289224 ng.h/ml, respectively as found by repeated rectangular rule. The errors in the approximated values of AUC were negligible. It is concluded that all computational tools approximated values of AUC accurately but the repeated rectangular rule gives slightly better approximated values of AUC as compared to repeated trapezium and repeated Simpson's rules.
Abstract: In recent years, Radio Frequency Identification (RFID)
is followed with interest by many researches, especially for the
purpose of indoor positioning as the innate properties of RFID are
profitable for achieving it. A lot of algorithms or schemes are proposed
to be used in the RFID-based positioning system, but most of them are
lack of environmental consideration and it induces inaccuracy of
application. In this research, a lot of algorithms and schemes of RFID
indoor positioning are discussed to see whether effective or not on
application, and some rules are summarized for achieving accurate
positioning. On the other hand, a new term “Noise Factor" is involved
to describe the signal loss between the target and the obstacle. As a
result, experimental data can be obtained but not only simulation; and
the performance of the positioning system can be expressed
substantially.
Abstract: One of the major disadvantages of the minimally
invasive surgery (MIS) is the lack of tactile feedback to the surgeon.
In order to identify and avoid any damage to the grasped complex
tissue by endoscopic graspers, it is important to measure the local
softness of tissue during MIS. One way to display the measured
softness to the surgeon is a graphical method. In this paper, a new
tactile sensor has been reported. The tactile sensor consists of an
array of four softness sensors, which are integrated into the jaws of a
modified commercial endoscopic grasper. Each individual softness
sensor consists of two piezoelectric polymer Polyvinylidene Fluoride
(PVDF) films, which are positioned below a rigid and a compliant
cylinder. The compliant cylinder is fabricated using a micro molding
technique. The combination of output voltages from PVDF films is
used to determine the softness of the grasped object. The theoretical
analysis of the sensor is also presented.
A method has been developed with the aim of reproducing the
tactile softness to the surgeon by using a graphical method. In this
approach, the proposed system, including the interfacing and the data
acquisition card, receives signals from the array of softness sensors.
After the signals are processed, the tactile information is displayed
by means of a color coding method. It is shown that the degrees of
softness of the grasped objects/tissues can be visually differentiated
and displayed on a monitor.
Abstract: In this paper, a new method of controlling position of AC Servomotor using Field Programmable Gate Array (FPGA). FPGA controller is used to generate direction and the number of pulses required to rotate for a given angle. Pulses are sent as a square wave, the number of pulses determines the angle of rotation and frequency of square wave determines the speed of rotation. The proposed control scheme has been realized using XILINX FPGA SPARTAN XC3S400 and tested using MUMA012PIS model Alternating Current (AC) servomotor. Experimental results show that the position of the AC Servo motor can be controlled effectively. KeywordsAlternating Current (AC), Field Programmable Gate Array (FPGA), Liquid Crystal Display (LCD).
Abstract: Road traffic accidents are a major cause of death worldwide. In an attempt to reduce accidents, some research efforts have focused on creating Advanced Driver Assistance Systems (ADAS) able to detect vehicle, driver and environmental conditions and to use this information to identify cues for potential accidents. This paper presents continued work on a novel Non-intrusive Intelligent Driver Assistance and Safety System (Ni-DASS) for assessing driver point of regard within vehicles. It uses an on-board CCD camera to observe the driver-s face. A template matching approach is used to compare the driver-s eye-gaze pattern with a set of eye-gesture templates of the driver looking at different focal points within the vehicle. The windscreen is divided into cells and comparison of the driver-s eye-gaze pattern with templates of a driver-s eyes looking at each cell is used to determine the driver-s point of regard on the windscreen. Results indicate that the proposed technique could be useful in situations where low resolution estimates of driver point of regard are adequate. For instance, To allow ADAS systems to alert the driver if he/she has positively failed to observe a hazard.
Abstract: Assembly line balancing is a very important issue in
mass production systems due to production cost. Although many
studies have been done on this topic, but because assembly line
balancing problems are so complex they are categorized as NP-hard
problems and researchers strongly recommend using heuristic
methods. This paper presents a new heuristic approach called the
critical task method (CTM) for solving U-shape assembly line
balancing problems. The performance of the proposed heuristic
method is tested by solving a number of test problems and comparing
them with 12 other heuristics available in the literature to confirm the
superior performance of the proposed heuristic. Furthermore, to
prove the efficiency of the proposed CTM, the objectives are
increased to minimize the number of workstation (or equivalently
maximize line efficiency), and minimizing the smoothness index.
Finally, it is proven that the proposed heuristic is more efficient than
the others to solve the U-shape assembly line balancing problem.
Abstract: An adaptive Fuzzy Inference Perceptual model has
been proposed for watermarking of digital images. The model
depends on the human visual characteristics of image sub-regions in
the frequency multi-resolution wavelet domain. In the proposed
model, a multi-variable fuzzy based architecture has been designed to
produce a perceptual membership degree for both candidate
embedding sub-regions and strength watermark embedding factor.
Different sizes of benchmark images with different sizes of
watermarks have been applied on the model. Several experimental
attacks have been applied such as JPEG compression, noises and
rotation, to ensure the robustness of the scheme. In addition, the
model has been compared with different watermarking schemes. The
proposed model showed its robustness to attacks and at the same time
achieved a high level of imperceptibility.
Abstract: Langmuir–Blodgett (LB) films of polyaniline (PANI) grown onto ITO coated glass substrates were utilized for the fabrication of Uric acid biosensor for efficient detection of uric acid by immobilizing Uricase via EDC–NHS coupling. The modified electrodes were characterized by atomic force microscopy (AFM). The response characteristics after immobilization of uricase were studied using cyclic voltammetry and electrochemical impedance spectroscopy techniques. The uricase/PANI/ITO/glass bioelectrode studied by CV and EIS techniques revealed detection of uric acid in a wide range of 0.05 mM to 1.0 mM, covering the physiological range in blood. A low Michaelis–Menten constant (Km) of 0.21 mM indicates the higher affinity of immobilized Uricase towards its analyte (uric acid). The fabricated uric acid biosensor based on PANI LB films exhibits excellent sensitivity of 0.21 mA/mM with a response time of 4 s, good reproducibility, long shelf life (8 weeks) and high selectivity.
Abstract: Due to the coexistence of different Radio Access
Technologies (RATs), Next Generation Wireless Networks (NGWN)
are predicted to be heterogeneous in nature. The coexistence of
different RATs requires a need for Common Radio Resource
Management (CRRM) to support the provision of Quality of Service
(QoS) and the efficient utilization of radio resources. RAT selection
algorithms are part of the CRRM algorithms. Simply, their role is to
verify if an incoming call will be suitable to fit into a heterogeneous
wireless network, and to decide which of the available RATs is most
suitable to fit the need of the incoming call and admit it.
Guaranteeing the requirements of QoS for all accepted calls and at
the same time being able to provide the most efficient utilization of
the available radio resources is the goal of RAT selection algorithm.
The normal call admission control algorithms are designed for
homogeneous wireless networks and they do not provide a solution
to fit a heterogeneous wireless network which represents the NGWN.
Therefore, there is a need to develop RAT selection algorithm for
heterogeneous wireless network. In this paper, we propose an
approach for RAT selection which includes receiving different
criteria, assessing and making decisions, then selecting the most
suitable RAT for incoming calls. A comprehensive survey of
different RAT selection algorithms for a heterogeneous wireless
network is studied.