Abstract: Cerium-doped lanthanum bromide LaBr3:Ce(5%)
crystals are considered to be one of the most advanced scintillator
materials used in PET scanning, combining a high light yield, fast
decay time and excellent energy resolution. Apart from the correct
choice of scintillator, it is also important to optimise the detector
geometry, not least in terms of source-to-detector distance in order to
obtain reliable measurements and efficiency. In this study a
commercially available 25 mm x 25 mm BrilLanCeTM 380 LaBr3: Ce
(5%) detector was characterised in terms of its efficiency at varying
source-to-detector distances. Gamma-ray spectra of 22Na, 60Co, and
137Cs were separately acquired at distances of 5, 10, 15, and 20cm. As
a result of the change in solid angle subtended by the detector, the
geometric efficiency reduced in efficiency with increasing distance.
High efficiencies at low distances can cause pulse pile-up when
subsequent photons are detected before previously detected events
have decayed. To reduce this systematic error the source-to-detector
distance should be balanced between efficiency and pulse pile-up
suppression as otherwise pile-up corrections would need to be
necessary at short distances. In addition to the experimental
measurements Monte Carlo simulations have been carried out for the
same setup, allowing a comparison of results. The advantages and
disadvantages of each approach have been highlighted.
Abstract: Many well-known interconnection networks, such as kary n-cubes, recursive circulant graphs, generalized recursive circulant graphs, circulant graphs and so on, are shown to belong to the family of cycle composition networks. Recently, various studies about mutually independent hamiltonian cycles, abbreviated as MIHC-s, on interconnection networks are published. In this paper, using an improved construction method, we obtain MIHC-s on cycle composition networks with a much weaker condition than the known result. In fact, we established the existence of MIHC-s in the cycle composition networks and the result is optimal in the sense that the number of MIHC-s we constructed is maximal.
Abstract: The use of bioindicators plants (lichens, bryophytes
and Sphagnum....) in monitoring pollution by heavy metals has been
the subject of several works. However, few studies have addressed
the impact of specific type-s pollutants (fertilizers, pesticides.) on
these organisms.
We propose in this work to make the highlighting effect of NPKs
(NPK: nitrogen-phosphate-potassium-sulfate (NP2O5K2O) (15,15,15),
at concentrations of 10, 20, 30 , 40 and 50mM/L) on the activity of
detoxification enzymes (GSH/GST, CAT, APX and MDA) of plant
bioindicators (mosses and lichens) after treatment for 3 and 7 days.
This study shows the important role of the defense system in the
accumulation and tolerance to chemical pollutants through the
activation of enzymatic (GST (glutathione-S-transferase, APX
(ascorbat peroxidase), CAT (catalase)) and nonenzymatic biomarkers
(GSH (glutathione), MDA (malondialdehyde)) against oxidative
stress generated by the NPKs.
Abstract: Larval survey was carried out in 6 localities in the
urban areas (Putrajaya) and suburban areas (Kuala Selangor) from
January until December 2010. A total of 520 representative
households in 6 localities were selected. Breeding habitats were
sampled outdoors in the surroundings of housing areas. The study
indicated that the most predominant species found in both areas was
Aedes albopictus with the gardening utensil as a preferred breeding
microhabitat for Putrajaya, in contrast to the artificial containers for
Kuala Selangor. From a total of 1083 mosquito larvae species, 984
were Aedes albopictus larvae, 67 positive larvae of Aedes aegypti
and 32 of Culex larvae. Aedes Index and Container Index were
elevated in Putrajaya with 13% and 11% respectively which is higher
than the standard given by the Ministry of Health, Malaysia. This
results implicating dengue-sensitive skewed to the urban areas.
Breteau Index result also above the standard in both study locations.
Abstract: Seismic design may require non-conventional
concept, due to the fact that the stiffness and layout of the structure
have a great effect on the overall structural behaviour, on the seismic
load intensity as well as on the internal force distribution. To find an
economical and optimal structural configuration the key issue is the
optimal design of the lateral load resisting system. This paper focuses
on the optimal design of regular, concentric braced frame (CBF)
multi-storey steel building structures. The optimal configurations are
determined by a numerical method using genetic algorithm approach,
developed by the authors. Aim is to find structural configurations
with minimum structural cost. The design constraints of objective
function are assigned in accordance with Eurocode 3 and Eurocode 8
guidelines. In this paper the results are presented for various building
geometries, different seismic intensities, and levels of energy
dissipation.
Abstract: The present research was designed to investigate the
anti-microbial activity of aristolochic acid from the root of
Aristolochia bracteata. From the methanolic & ethyl extract extracts
of Aristolochia bracteata aristolochic acid I was isolated and
conformed through IR, NMR & MS. The percentage purity of
aristolochic acid I was determined by UV & HPLC method. Antibacterial
activity of extracts of Aristolochia bracteata and the
isolated compound was determined by disc diffusion method. The
results reveled that the isolated aristolochic acid from methanolic
extract was more pure than the compound from ethyl acetate extract.
The various extracts (500μg/disc) of Aristolochia bracteata showed
moderate antibacterial activity with the average zone of inhibition of
7-18 mm by disc diffusion method. Among the extracts, ethyl acetate
& methanol extracts were shown good anti-microbial activity and the
growth of E.coli (18 mm) was strongly inhibited. Microbial assay of
isolated compound (Aristolochic acid I) from ethyl acetate &
methanol extracts were shown good antimicrobial activity and the
zone of inhibition of both at higher concentration 50 μg/ml was
similar with the standard aristolochic acid. It may be concluded that
the isolated compound of aristolochic acid I has good anti-bacterial
activity.
Abstract: Lipases are enzymes particularly amenable for
immobilization by entrapment methods, as they can work equally
well in aqueous or non-conventional media and long-time stability of
enzyme activity and enantioselectivity is needed to elaborate more
efficient bioprocesses. The improvement of Pseudomonas
fluorescens (Amano AK) lipase characteristics was investigated by
optimizing the immobilization procedure in hybrid organic-inorganic
matrices using ionic liquids as additives. Ionic liquids containing a
more hydrophobic alkyl group in the cationic moiety are beneficial
for the activity of immobilized lipase. Silanes with alkyl- or aryl
nonhydrolizable groups used as precursors in combination with
tetramethoxysilane could generate composites with higher
enantioselectivity compared to the native enzyme in acylation
reactions of secondary alcohols. The optimal effect on both activity
and enantioselectivity was achieved for the composite made from
octyltrimethoxysilane and tetramethoxysilane at 1:1 molar ratio (60%
increase of total activity following immobilization and enantiomeric
ratio of 30). Ionic liquids also demonstrated valuable properties as
reaction media for the studied reactions, comparable with the usual
organic solvent, hexane.
Abstract: The purpose of this study was to explore the complex
flow structure a novel active-type micromixer that based on concept of
Wankle-type rotor. The characteristics of this micromixer are two
folds; a rapid mixing of reagents in a limited space due to the
generation of multiple vortices and a graduate increment in dynamic
pressure as the mixed reagents is delivered to the output ports.
Present micro-mixer is consisted of a rotor with shape of triangle
column, a blending chamber and several inlet and outlet ports. The
geometry of blending chamber is designed to make the rotor can be
freely internal rotated with a constant eccentricity ratio. When the
shape of the blending chamber and the rotor are fixed, the effects of
rotating speed of rotor and the relative locations of ports on the mixing
efficiency are numerical studied. The governing equations are
unsteady, two-dimensional incompressible Navier-Stokes equation
and the working fluid is the water. The species concentration equation
is also solved to reveal the mass transfer process of reagents in various
regions then to evaluate the mixing efficiency.
The dynamic mesh technique was implemented to model the
dynamic volume shrinkage and expansion of three individual
sub-regions of blending chamber when the rotor conducted a complete
rotating cycle. Six types of ports configuration on the mixing
efficiency are considered in a range of Reynolds number from 10 to
300. The rapid mixing process was accomplished with the multiple
vortex structures within a tiny space due to the equilibrium of shear
force, viscous force and inertial force. Results showed that the highest
mixing efficiency could be attained in the following conditions: two
inlet and two outlet ports configuration, that is an included angle of 60
degrees between two inlets and an included angle of 120 degrees
between inlet and outlet ports when Re=10.
Abstract: The selection of parents and breeding strategies for
the successful maize hybrid production will be facilitated by
heterotic groupings of parental lines and determination of combining
abilities of them. Fourteen maize inbred lines, used in maize breeding
programs in Iran, were crossed in a diallel mating design. The 91 F1
hybrids and the 14 parental lines were studied during two years at
four locations of Iran for investigation of combining ability of
gentypes for grain yield and to determine heterotic patterns among
germplasm sources, using both, the Griffing-s method and the biplot
approach for diallel analysis. The graphical representation offered by
biplot analysis allowed a rapid and effective overview of general
combining ability (GCA) and specific combining ability (SCA)
effects of the inbred lines, their performance in crosses, as well as
grouping patterns of similar genotypes. GCA and SCA effects were
significant for grain yield (GY). Based on significant positive GCA
effects, the lines derived from LSC could be used as parent in crosses
to increase GY. The maximum best- parent heterosis values and
highest SCA effects resulted from crosses B73 × MO17 and A679 ×
MO17 for GY. The best heterotic patterns were LSC × RYD, which
would be potentially useful in maize breeding programs to obtain
high-yielding hybrids in the same climate of Iran.
Abstract: This paper proposes the concept of aerocapture with
aerodynamic-environment-adaptive variable geometry flexible
aeroshell that vehicle deploys. The flexible membrane is composed
of thin-layer film or textile as its aeroshell in order to solve some
problems obstructing realization of aerocapture technique.
Multi-objective optimization study is conducted to investigate
solutions and derive design guidelines. As a result, solutions which
can avoid aerodynamic heating and enlarge the corridor width up
to 10% are obtained successfully, so that the effectiveness of this
concept can be demonstrated. The deformation-use optimum
solution changes its drag coefficient from 1.6 to 1.1, along with the
change in dynamic pressure. Moreover, optimization results show
that deformation-use solution requires the membrane for which
upper temperature limit and strain limit are more than 700 K and
120%, respectively, and elasticity (Young-s modulus) is of order of
106 Pa.
Abstract: Bangladesh is a developing country with large
population. Demand of electrical energy is increasing day by day
because of increasing population and industrialization. But due to
limited resources, people here are suffering from power crisis
problem which is considered as a major obstacle to the economic
development. In most of the cases, it is extremely difficult to extend
high tension transmission lines to some of the places that are
separated from the mainland. Renewable energy is considered to be
the right choice for providing clean energy to these remote
settlements. This paper proposes a cost effective design of off-grid
wind-diesel hybrid power system using combined heat and power
(CHP) technology in a grid isolated island, Sandwip, Bangladesh.
Design and simulation of the wind-diesel hybrid power system is
performed considering different factors for the island Sandwip.
Detailed economic analysis and comparison with solar PV system
clearly reveals that wind-diesel hybrid power system can be a cost
effective solution for the isolated island like Sandwip.
Abstract: A manufacturing inventory model with shortages with
carrying cost, shortage cost, setup cost and demand quantity as
imprecise numbers, instead of real numbers, namely interval number
is considered here. First, a brief survey of the existing works on
comparing and ranking any two interval numbers on the real line
is presented. A common algorithm for the optimum production
quantity (Economic lot-size) per cycle of a single product (so as
to minimize the total average cost) is developed which works well
on interval number optimization under consideration. Finally, the
designed algorithm is illustrated with numerical example.
Abstract: Bones are dynamic and responsive organs, they
regulate their strength and mass according to the loads which they are subjected. Because, the Wnt/β-catenin pathway has profound
effects on the regulation of bone mass, we hypothesized that mechanical loading of bone cells stimulates Wnt/β-catenin signaling, which results in the generation of new bone mass.
Mechanical loading triggers the secretion of the Wnt molecule, which after binding to transmembrane proteins, causes GSK-3β (Glycogen synthase kinase 3 beta) to cease the phosphorylation of β-catenin. β-catenin accumulation in the cytoplasm, followed by its
transport into the nucleus, binding to transcription factors (TCF/LEF)
that initiate transcription of genes related to bone formation. To test this hypothesis, we used TOPGAL (Tcf Optimal Promoter
β-galactosidase) mice in an experiment in which cyclic loads were
applied to the forearm. TOPGAL mice are reporters for cells effected
by the Wnt/β-catenin signaling pathway. TOPGAL mice are genetically engineered mice in which transcriptional activation of β-
catenin, results in the production of an enzyme, β-galactosidase. The
presence of this enzyme allows us to localize transcriptional
activation of β-catenin to individual cells, thereby, allowing us to quantify the effects that mechanical loading has on the Wnt/β-catenin pathway and new bone formation. The ulnae of loaded TOPGAL
mice were excised and transverse slices along different parts of the
ulnar shaft were assayed for the presence of β-galactosidase.
Our results indicate that loading increases β-catenin transcriptional
activity in regions where this pathway is already primed (i.e. where basal activity is already higher) in a load magnitude dependent
manner. Further experiments are needed to determine the temporal and spatial activation of this signaling in relation to bone formation.
Abstract: Fatigue cracking continues to be the main challenges in
improving the performance of bituminous mixture pavements. The
purpose of this paper is to look at some aspects of the effects of fine
aggregate properties on the fatigue behaviour of hot mixture asphalt.
Two types of sand (quarry and mining sand) with two conventional
bitumen (PEN 50/60 & PEN 80/100) and four polymers modified
bitumen PMB (PM1_82, PM1_76, PM2_82 and PM2_76) were used.
Physical, chemical and mechanical tests were performed on the sands
to determine their effect when incorporated with a bituminous
mixture. According to the beam fatigue results, quarry sand that has
more angularity, rougher, higher shear strength and a higher
percentage of Aluminium oxide presented higher resistance to
fatigue. Also a PMB mixture gives better fatigue results than
conventional mixtures, this is due to the PMB having better viscosity
property than that of the conventional bitumen.
Abstract: This paper presents a hybrid fuzzy-PD plus PID
(HFPP) controller and its application to steam distillation process for
essential oil extraction system. Steam temperature is one of the most
significant parameters that can influence the composition of essential
oil yield. Due to parameter variations and changes in operation
conditions during distillation, a robust steam temperature controller becomes nontrivial to avoid the degradation of essential oil quality.
Initially, the PRBS input is triggered to the system and output of steam temperature is modeled using ARX model structure. The
parameter estimation and tuning method is adopted by simulation
using HFPP controller scheme. The effectiveness and robustness of
proposed controller technique is validated by real time
implementation to the system. The performance of HFPP using 25 and 49 fuzzy rules is compared. The experimental result demonstrates the proposed HFPP using 49 fuzzy rules achieves a
better, consistent and robust controller compared to PID when considering the test on tracking the set point and the effects due to disturbance.
Abstract: We introduce an adaptive technique for the joint mitigation of transients and continuous-wave radio-frequency co-channel interference (CW RFI) in high-frequency (HF) over-the-horizon radars (OTHRs). The performance of this technique is illustrated using data from an operational surface-wave radar (SECAR) and from recent experimental trials with sky-wave (SW) and sky-wave–line-of-sight (SKYLOS) HF OTHRs.
Abstract: In this study, a longitudinal joint connection was
proposed for the short-span slab-type modular bridges with rapid
construction. The slab-type modular bridge consists of a number of
precast slab modules and has the joint connection between the
modules in the longitudinal direction of the bridge. A finite element
based parameter analysis was conducted to design the shape and the
dimensions of the longitudinal joint connection. Numbers of shear
keys within the joint, height and depth of the shear key, tooth angle,
and the spacing were considered as the design parameters. Using the
local cracking load at the corner of the shear key and the
cross-sectional area of the joint, an efficiency factor was proposed to
evaluate the effectiveness of the longitudinal joint connection. The
dimensions of shear key were determined by comparing the cracking
loads and the efficiency factors obtained from the finite element
analysis.
Abstract: An interesting method to produce calcium carbonate is based in a gas-liquid reaction between carbon dioxide and aqueous solutions of calcium hydroxide. The design parameters for gas-liquid phase are flow regime, individual mass transfer, gas-liquid specific interfacial area. Most studies on gas-liquid phase were devoted to the experimental determination of some of these parameters, and more specifically, of the mass transfer coefficient, kLa which depends fundamentally on the superficial gas velocity and on the physical properties of absorption phase. The principle investigation was directed to study the effect of the vibration on the mass transfer coefficient kLa in gas-liquid phase during absorption of CO2 in the in aqueous solution of calcium hydroxide. The vibration with a higher frequency increase the mass transfer coefficient kLa, but vibration with lower frequency didn-t improve it, the mass transfer coefficient kLa increase with increase the superficial gas velocity.
Abstract: PDMS (Polydimethylsiloxane) polymer is a suitable material for biological and MEMS (Microelectromechanical systems) designers, because of its biocompatibility, transparency and high resistance under plasma treatment. PDMS round channel is always been of great interest due to its ability to confine the liquid with membrane type micro valves. In this paper we are presenting a very simple way to form round shapemicrofluidic channel, which is based on reflow of positive photoresist AZ® 40 XT. With this method, it is possible to obtain channel of different height simply by varying the spin coating parameters of photoresist.
Abstract: Recently, a great amount of interest has been shown
in the field of modeling and controlling hybrid systems. One of the
efficient and common methods in this area utilizes the mixed logicaldynamical
(MLD) systems in the modeling. In this method, the
system constraints are transformed into mixed-integer inequalities by
defining some logic statements. In this paper, a system containing
three tanks is modeled as a nonlinear switched system by using the
MLD framework. Comparing the model size of the three-tank system
with that of a two-tank system, it is deduced that the number of
binary variables, the size of the system and its complexity
tremendously increases with the number of tanks, which makes the
control of the system more difficult. Therefore, methods should be
found which result in fewer mixed-integer inequalities.