Abstract: A numerical analysis of a reinforced concrete (RC) wall under missile impact loading is presented in this study. The model created by Technical Research Center of Finland was used. The commercial finite element code, LS-DYNA was used to analyze. The structural components of the reinforced concrete wall, missile and their contacts are fully modeled. The material nonlinearity with strain rate effects considering damage and failure is included in the analysis. The results of analysis were verified with other research results. The case-studies with different reinforcement ratios were conducted to investigate the influence of reinforcement on the punching behavior of walls under missile impact.
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Abstract: This Paper presents an on-going research in the area of Model-Driven Engineering (MDE). The premise is that UML is too unwieldy to serve as the basis for model-driven engineering. We need a smaller, simpler notation with a cleaner semantics. We propose some ideas for a simpler notation with a clean semantics. The result is known as μML, or the Micro-Modelling Language.
Abstract: As the information age matures, major social
infrastructures such as communication, finance, military and energy,
have become ever more dependent on information communication
systems. And since these infrastructures are connected to the Internet,
electronic intrusions such as hacking and viruses have become a new
security threat. Especially, disturbance or neutralization of a major
social infrastructure can result in extensive material damage and social
disorder. To address this issue, many nations around the world are
researching and developing various techniques and information
security policies as a government-wide effort to protect their
infrastructures from newly emerging threats. This paper proposes an
evaluation method for information security levels of CIIP (Critical
Information Infrastructure Protection), which can enhance the security
level of critical information infrastructure by checking the current
security status and establish security measures accordingly to protect
infrastructures effectively.
Abstract: Tubular process equipment is often damaged in
industrial processes. The damage occurs both on devices working at
high temperatures and also on less exposed devices. In case of sudden
damage of key equipment a shutdown of the whole production unit
and resulting significant economic losses are imminent. This paper
presents a solution of several types of tubular process equipment. The
causes of damage and suggestions of correction actions are discussed
in all cases. Very important part is the analysis of operational
conditions, determination of unfavourable working states decreasing
lifetime of devices and suggestions of correction actions. Lately very
popular numerical methods are used for analysis of the equipment.
Abstract: The carbon based coils with the nanometer scale have
the 3 dimension helix geometry. We synthesized the carbon nano-coils
by the use of chemical vapor deposition technique with iron and tin as
the catalysts. The fabricated coils have the external diameter of
ranging few hundred nm to few thousand nm. The Scanning
Electro-Microscope (SEM) and Tunneling Electro-Microscope has
shown detail images of the coil-s structure. The fabrication of the
carbon nano-coils can be grown on the metal and non-metal substrates,
such as the stainless steel and silicon substrates. Besides growth on the
flat substrate; they also can be grown on the stainless steel wires. After
the synthesis of the coils, the mechanical and electro-mechanical
property is measured. The experimental results were reported.
Abstract: Due to its geographical location, Iran is considered one of the earthquake-prone areas where the best way to decrease earthquake effects is supposed to be strengthening the buildings. Even though, one idea suggests that the use of adobe in constructing buildings be prohibited for its weak function especially in earthquake-prone areas, however, regarding ecological considerations, sustainability and other local skills, another idea pays special attention to adobe as one of the construction technologies which is popular among people. From the architectural and technological point of view, as strong sustainable building construction materials, compressed adobe construction materials make most of the construction in urban or rural areas ranging from small to big industrial buildings used to replace common earth blocks in traditional systems and strengthen traditional adobe buildings especially against earthquake. Mentioning efficient construction using compressed adobe system as a reliable replacement for traditional soil construction materials , this article focuses on the experiences of India in the fields of sustainable development of compressed adobe systems in the form of system in which the compressed soil is combined with cement, load bearing building with brick/solid concrete block system, brick system using rat trap bond, metal system with adobe infill and finally emphasizes on the use of these systems in the earthquake-struck city of Bam in Iran.
Abstract: Due to the liberalization of countless electricity markets, load forecasting has become crucial to all public utilities for which electricity is a strategic variable. With the goal of contributing to the forecasting process inside public utilities, this paper addresses the issue of applying the Holt-Winters exponential smoothing technique and the time series analysis for forecasting the hourly electricity load curve of the Italian railways. The results of the analysis confirm the accuracy of the two models and therefore the relevance of forecasting inside public utilities.
Abstract: This study examines the use of the persuasive strategy
of deixis and personalization in advertising slogans. This rhetorical/
stylistic and linguistic strategy has been found to be widely used in
advertising slogans for over a century. A total of five hundred
advertising slogans of multinational companies in both product and
service sectors were obtained. The analysis reveals the 3 main
components of this strategy as being deictic words, absolute
uniqueness and personal pronouns. The percentage and mean of the
use of the 3 components are tabulated. The findings show that
advertisers have used this persuasive strategy in creative ways to
persuade consumers to buy their products and services.
Abstract: Performing High Voltage (HV) tasks with a multi craft
work force create a special set of safety circumstances. This paper
aims to present vital information relating to when it is acceptable to
use a single or a two-layer soil structure. Also it discusses the
implication of the high voltage infrastructure on the earth grid and the
safety of this implication under a single or a two-layer soil structure.
A multiple case study is investigated to show the importance of using
the right soil resistivity structure during the earthing system design.
Abstract: In general dynamic analyses, lower mode response is
of interest, however the higher modes of spatially discretized
equations generally do not represent the real behavior and not affects
to global response much. Some implicit algorithms, therefore, are
introduced to filter out the high-frequency modes using intended
numerical error. The objective of this study is to introduce the
P-method and PC α-method to compare that with dissipation method
and Newmark method through the stability analysis and numerical
example. PC α-method gives more accuracy than other methods
because it based on the α-method inherits the superior properties of the
implicit α-method. In finite element analysis, the PC α-method is more
useful than other methods because it is the explicit scheme and it
achieves the second order accuracy and numerical damping
simultaneously.
Abstract: The frontal area in the brain is known to be involved in
behavioral judgement. Because a Kanji character can be discriminated
visually and linguistically from other characters, in Kanji character
discrimination, we hypothesized that frontal event-related potential
(ERP) waveforms reflect two discrimination processes in separate
time periods: one based on visual analysis and the other based
on lexcical access. To examine this hypothesis, we recorded ERPs
while performing a Kanji lexical decision task. In this task, either a
known Kanji character, an unknown Kanji character or a symbol was
presented and the subject had to report if the presented character was
a known Kanji character for the subject or not. The same response
was required for unknown Kanji trials and symbol trials. As a preprocessing
of signals, we examined the performance of a method
using independent component analysis for artifact rejection and found
it was effective. Therefore we used it. In the ERP results, there
were two time periods in which the frontal ERP wavefoms were
significantly different betweeen the unknown Kanji trials and the
symbol trials: around 170ms and around 300ms after stimulus onset.
This result supported our hypothesis. In addition, the result suggests
that Kanji character lexical access may be fully completed by around
260ms after stimulus onset.
Abstract: Soursop (Anona muricata) is one of the underutilized tropical fruits containing nutrients, particularly dietary fibre and antioxidant properties that are beneficial to human health. This objective of this study is to investigate the feasibility of matured soursop pulp flour (SPF) to be substituted with high-protein wheat flour in bread. Bread formulation was substituted with different levels of SPF (0%, 5%, 10% and 15%). The effect on physicochemical properties and sensory attributes were evaluated. Higher substitution level of SPF resulted in significantly higher (p
Abstract: MiRNAs participate in gene regulation of translation.
Some studies have investigated the interactions between genes and
intragenic miRNAs. It is important to study the miRNA binding sites
of genes involved in carcinogenesis. RNAHybrid 2.1 and ERNAhybrid
programmes were used to compute the hybridization free
energy of miRNA binding sites. Of these 54 mRNAs, 22.6%, 37.7%,
and 39.7% of miRNA binding sites were present in the 5'UTRs,
CDSs, and 3'UTRs, respectively. The density of the binding sites for
miRNAs in the 5'UTR ranged from 1.6 to 43.2 times and from 1.8 to
8.0 times greater than in the CDS and 3'UTR, respectively. Three
types of miRNA interactions with mRNAs have been revealed: 5'-
dominant canonical, 3'-compensatory, and complementary binding
sites. MiRNAs regulate gene expression, and information on the
interactions between miRNAs and mRNAs could be useful in
molecular medicine. We recommend that newly described sites
undergo validation by experimental investigation.
Abstract: The aim of this paper is to introduce a parametric
distribution model in fatigue life reliability analysis dealing with
variation in material properties. Service loads in terms of responsetime
history signal of Belgian pave were replicated on a multi-axial
spindle coupled road simulator and stress-life method was used to
estimate the fatigue life of automotive stub axle. A PSN curve was
obtained by monotonic tension test and two-parameter Weibull
distribution function was used to acquire the mean life of the
component. A Pearson system was developed to evaluate the fatigue
life reliability by considering stress range intercept and slope of the
PSN curve as random variables. Considering normal distribution of
fatigue strength, it is found that the fatigue life of the stub axle to
have the highest reliability between 10000 – 15000 cycles. Taking
into account the variation of material properties associated with the
size effect, machining and manufacturing conditions, the method
described in this study can be effectively applied in determination of
probability of failure of mass-produced parts.
Abstract: In industry, on of the most important subjects is die
and it's characteristics in which for cutting and forming different
mechanical pieces, various punch and matrix metal die are used.
whereas the common parts which form the main frame die are not
often proportion with pieces and dies therefore using a part as socalled
common part for frames in specified dimension ranges can
decrease the time of designing, occupied space of warehouse and
manufacturing costs. Parts in dies with getting uniform in their shape
and dimension make common parts of dies. Common parts of punch
and matrix metal die are as bolster, guide bush, guide pillar and
shank. In this paper the common parts and effective parameters in
selecting each of them as the primary information are studied,
afterward for selection and design of mechanical parts an
introduction and investigation based on the Mech. Desk. software is
done hence with developing this software can standardize the metal
common parts of punch and matrix. These studies will be so useful
for designer in their designing and also using it has with very much
advantage for manufactures of products in decreasing occupied
spaces by dies.
Abstract: Novel polystrene-bound Schiff bases and their Pt(IV)
complexes have been prepared from condensation reaction of
polystyrene-A-NH2 with 2-hydroxybenzaldehyde and 5-fluoro-3-
bromo-2-hydroxybenzaldehyde. The structures of Pt(IV) complexes
with polystyrene including Schiff bases have been determined by
elemental analyses, magnetic susceptibility, IR, 1H-NMR, UV-vis,
TG/DTA and AAS. The antibacterial and antifungal activities of the
synthesized compounds have been studied by the well-diffusion
method against some selected microorganisms: (Bacillus cereus spp.,
Listeria monocytogenes 4b, Micrococcus luteus, Staphylococcus
aureus, Staphylococcus epidermis, Brucella abortus, Escherichia
coli, Pseudomonas putida spp., Shigella dysenteria type 10,
Salmonella typhi H).
Abstract: Currently, many types of no-reversible compressed
sound source, represented by MP3 (MPEG Audio Layer-3) are
popular in the world and they are widely used to make the music file
size smaller. The sound data created in this way has less information as
compared to pre-compressed data. The objective of this study is by
analyzing EEG to determine if people can recognize such difference as
differences in sound. A measurement system that can measure and
analyze EEG when a subject listens to music were experimentally
developed. And ten subjects were studied with this system. In this
experiment, a WAVE formatted music data and a MP3 compressed
music data that is made from the WAVE formatted data were
prepared. Each subject was made to hear these music sources at the
same volume. From the results of this experiment, clear differences
were confirmed between two wound sources.
Abstract: Pulse code modulation is a widespread technique
in digital communication with significant impact on existing
modern and proposed future communication technologies. Its
widespread utilization is due to its simplicity and attractive
spectral characteristics. In this paper, we present a new
approach to the spectral analysis of PCM signals using
Riemann-Stieltjes integrals, which is very accurate for high bit
rates. This approach can serve as a model for similar spectral
analysis of other competing modulation schemes.
Abstract: High level and high velocity flood flows are
potentially harmful to bridge piers as evidenced in many toppled
piers, and among them the single-column piers were considered as
the most vulnerable. The flood flow characteristic parameters
including drag coefficient, scouring and vortex shedding are built into
a pier-flood interaction model to investigate structural safety against
flood hazards considering the effects of local scouring, hydrodynamic
forces, and vortex induced resonance vibrations. By extracting the
pier-flood simulation results embedded in a neural networks code,
two cases of pier toppling occurred in typhoon days were reexamined:
(1) a bridge overcome by flash flood near a mountain side;
(2) a bridge washed off in flood across a wide channel near the
estuary. The modeling procedures and simulations are capable of
identifying the probable causes for the tumbled bridge piers during
heavy floods, which include the excessive pier bending moments and
resonance in structural vibrations.