Abstract: Evolvable Hardware (EHW) has been regarded as adaptive system acquired by wide application market. Consumer market of any good requires diversity to satisfy consumers- preferences. Adaptation of EHW is a key technology that could provide individual approach to every particular user. This situation raises a question: how to set target for evolutionary algorithm? The existing techniques do not allow consumer to influence evolutionary process. Only designer at the moment is capable to influence the evolution. The proposed consumer-triggered evolution overcomes this problem by introducing new features to EHW that help adaptive system to obtain targets during consumer stage. Classification of EHW is given according to responsiveness, imitation of human behavior and target circuit response. Home intelligent water heating system is considered as an example.
Abstract: A study concerning the photocatalytic decolourization
of Congo red (CR) dye, over artificial UV irradiation is presented.
Photocatalysts based on a commercial titanium dioxide (TiO2)
modified with transition metals (Ni, Cu and Zn) were used. The
dopage method used was wet impregnation. A TiO2 sample without
salt was subjected to the same hydrothermal treatment to be used as
reference. Congo red solutions to several pH conditions (natural and
basic) were used to evaluate photocatalytic performance of each
doped catalysts. Photodecolourization percentage was measured
spectrofotrometically after 3 h of treatment to 499 nm as response
variable. Kinetics investigations of photodegradation indicated that
reactions obey to Langmuir-Hinshelwood model and pseudo–first
order law. The rate constant studies of photocatalytic decolourization
reactions for Zn–TiO2 and Cu–TiO2 photocatalysts indicated that in
all cases the rate constant of the reaction was higher than that of TiO2
undoped. These results show that nature of the metal modifying the
TiO2 influence on the efficiency of the photocatalyst evaluated in
process. Ni does not present an additional effect compared with TiO2,
while Zn enhances the photoactivity due to its electronic properties.
Abstract: Due to the dynamic nature of the Cloud, continuous monitoring of QoS requirements is necessary to manage the Cloud computing environment. The process of QoS monitoring and SLA violation detection consists of: collecting low and high level information pertinent to the service, analyzing the collected information, and taking corrective actions when SLA violations are detected. In this paper, we detail the architecture and the implementation of the first step of this process. More specifically, we propose an event-based approach to obtain run time information of services developed as BPEL processes. By catching particular events (i.e., the low level information), our approach recognizes the run-time execution path of a monitored service and uses the BPEL execution patterns to compute QoS of the composite service (i.e., the high level information).
Abstract: Research papers are usually evaluated via peer
review. However, peer review has limitations in evaluating research
papers. In this paper, Scienstein and the new idea of 'collaborative
document evaluation' are presented. Scienstein is a project to
evaluate scientific papers collaboratively based on ratings, links,
annotations and classifications by the scientific community using the
internet. In this paper, critical success factors of collaborative
document evaluation are analyzed. That is the scientists- motivation
to participate as reviewers, the reviewers- competence and the
reviewers- trustworthiness. It is shown that if these factors are
ensured, collaborative document evaluation may prove to be a more
objective, faster and less resource intensive approach to scientific
document evaluation in comparison to the classical peer review
process. It is shown that additional advantages exist as collaborative
document evaluation supports interdisciplinary work, allows
continuous post-publishing quality assessments and enables the
implementation of academic recommendation engines. In the long
term, it seems possible that collaborative document evaluation will
successively substitute peer review and decrease the need for
journals.
Abstract: Verification of real-time software systems can be
expensive in terms of time and resources. Testing is the main method
of proving correctness but has been shown to be a long and time
consuming process. Everyday engineers are usually unwilling to
adopt formal approaches to correctness because of the overhead
associated with developing their knowledge of such techniques.
Performance modelling techniques allow systems to be evaluated
with respect to timing constraints. This paper describes PARTES, a
framework which guides the extraction of performance models from
programs written in an annotated subset of C.
Abstract: This paper presents a heuristic approach to solve the Generalized Assignment Problem (GAP) which is NP-hard. It is worth mentioning that many researches used to develop algorithms for identifying the redundant constraints and variables in linear programming model. Some of the algorithms are presented using intercept matrix of the constraints to identify redundant constraints and variables prior to the start of the solution process. Here a new heuristic approach based on the dominance property of the intercept matrix to find optimal or near optimal solution of the GAP is proposed. In this heuristic, redundant variables of the GAP are identified by applying the dominance property of the intercept matrix repeatedly. This heuristic approach is tested for 90 benchmark problems of sizes upto 4000, taken from OR-library and the results are compared with optimum solutions. Computational complexity is proved to be O(mn2) of solving GAP using this approach. The performance of our heuristic is compared with the best state-ofthe- art heuristic algorithms with respect to both the quality of the solutions. The encouraging results especially for relatively large size test problems indicate that this heuristic approach can successfully be used for finding good solutions for highly constrained NP-hard problems.
Abstract: The possibility of producing drinking water from
brackish ground water using Vacuum membrane distillation (VMD)
process was studied. It is a rising technology for seawater or brine
desalination process. The process simply consists of a flat sheet
hydrophobic micro porous PTFE membrane and diaphragm vacuum
pump without a condenser for the water recovery or trap. In this
work, VMD performance was investigated for aqueous NaCl solution
and natural ground water. The influence of operational parameters
such as feed flow rate (30 to 55 l/h), feed temperature (313 to 333 K),
feed salt concentration (5000 to 7000 mg/l) and permeate pressure
(1.5 to 6 kPa) on the membrane distillation (MD) permeation flux
have been investigated. The maximum flux reached to 28.34 kg/m2 h
at feed temperature, 333 K; vacuum pressure, 1.5 kPa; feed flow rate,
55 l/h and feed salt concentration, 7000 mg/l. The negligible effects
in the reduction of permeate flux found over 150 h experimental run
for salt water. But for the natural ground water application over 75 h,
scale deposits observed on the membrane surface and 29% reduction
in the permeate flux over 75 h. This reduction can be eliminated by
acidification of feed water. Hence, promote the research attention in
apply of VMD for the ground water purification over today-s
conventional RO operation.
Abstract: In order to explore the relationship of promotion activities, destination attribute and destination image of Vietnam and find possible solutions, this study uses decision system analysis (DSA) method to develop flowcharts based on three rounds of expert interviews. The interviews were conducted with the experts who were confirmed to directly participate or influence on the decision making that drives the promotion of Vietnam tourism process. This study identifies three models and describes specific decisions on promotion activities, destination attributes and destination images. This study finally derives a general model for promoting the Tourism Industrial Service Network (TISN) in Vietnam. This study finds that the coordination with all sectors and industries of tourism to facilitate favorable condition and improving destination attributes in linking with the efficient promotion activities is highly recommended in order to make visitors satisfied and improve the destination image.
Abstract: Collaborative problem solving in e-learning can take
in the form of discussion among learner, creating a highly social
learning environment and characterized by participation and
interactivity. This paper, designed a collaborative learning
environment where agent act as co-learner, can play different roles
during interaction. Since different roles have been assigned to the
agent, learner will assume that multiple co-learner exists to help and
guide him all throughout the collaborative problem solving process,
but in fact, alone during the learning process. Specifically, it answers
the questions what roles of the agent should be incorporated to
contribute better learning outcomes, how agent will facilitate the
communication process to provide social learning and interactivity
and what are the specific instructional strategies that facilitate learner
participation, increased skill acquisition and develop critical thinking.
Abstract: Cobalt was acid nitric leached from a mixed cobaltcopper
oxide with variable acid concentration. Resulting
experimental data were used to analyze effects of increase in acid
concentration, based on a shrinking core model of the process. The
mathematical simulation demonstrated that the time rate of the
dissolution mechanism is an increasing function of acid
concentration. It was also shown that the magnitude of the acid
concentration effect is time dependent and the increase in acid
concentration is more effective at earlier stage of the dissolution than
at later stage. The remaining process parameters are comprehensively
affected by acid concentration and their interaction is synergetic.
Abstract: One of the determinants of a firm-s prosperity is the
customers- perceived service quality and satisfaction. While service
quality is wide in scope, and consists of various dimensions, there
may be differences in the relative importance of these dimensions in
affecting customers- overall satisfaction of service quality.
Identifying the relative rank of different dimensions of service quality
is very important in that it can help managers to find out which
service dimensions have a greater effect on customers- overall
satisfaction. Such an insight will consequently lead to more effective
resource allocation which will finally end in higher levels of
customer satisfaction. This issue – despite its criticality- has not
received enough attention so far. Therefore, using a sample of 240
bank customers in Iran, an artificial neural network is developed to
address this gap in the literature. As customers- evaluation of service
quality is a subjective process, artificial neural networks –as a brain
metaphor- may appear to have a potentiality to model such a
complicated process. Proposing a neural network which is able to
predict the customers- overall satisfaction of service quality with a
promising level of accuracy is the first contribution of this study. In
addition, prioritizing the service quality dimensions in affecting
customers- overall satisfaction –by using sensitivity analysis of
neural network- is the second important finding of this paper.
Abstract: Among the chemicals used for ammunition production, TNT (Trinitrotoluene) play a significant role since World War I and II. Various types of military weapon utilize TNT in casting process. However, the TNT casting process for warhead is difficult to control the cooling rate of the liquid TNT. This problem occurs because the casting process lacks the equipment to detect the temperature during the casting procedure This study presents the temperature detected by infrared camera to illustrate the cooling rate and cooling zone of curing, and demonstrates the optimization of TNT condition to reduce the risk of air gap occurred in the warhead which can result in the destruction afterward. Premature initiation of explosive-filled projectiles in response to set-back forces during gunfiring cause by casting defects. Finally the study can help improving the process of the TNT casting. The operators can control the curing of TNT inside the case by rising up the heating rod at the proper time. Consequently this can reduce tremendous time of rework if the air gaps occur and increase strength to lower elastic modulus. Therefore, it can be clearly concluded that the use of Infrared Cameras in this process is another method to improve the casting procedure.
Abstract: The objective of this article is to discuss the potential
of economic analysis as a tool for identification and evaluation of
corruption in legislative acts. We propose that corruption be
perceived as a risk variable within the legislative process. Therefore
we find it appropriate to employ risk analysis methods, used in
various fields of economics, for the evaluation of corruption in
legislation. Furthermore we propose the incorporation of these
methods into the so called corruption impact assessment (CIA), the
general framework for detection of corruption in legislative acts. The
applications of the risk analysis methods are demonstrated on
examples of implementation of proposed CIA in the Czech Republic.
Abstract: The article deals with pneumatic and hot wire
anemometry measurement on subsonic axi-symmetric air ejector.
Performances of the ejector with and without pulsations of primary
flow are compared, measuring of characteristic pressures and mass
flow rates are performed and ejector efficiency is evaluated. The
pulsations of primary flow are produced by a synthetic jet generator,
which is placed in the supply line of the primary flow just in front of
the primary nozzle. The aim of the pulsation is to intensify the
mixing process. In the article we present: Pressure measuring of
pulsation on the mixing chamber wall, behind the mixing chamber
and behind the diffuser measured by fast pressure transducers and
results of hot wire anemometry measurement. It was found out that
using of primary flow pulsations yields higher back pressure behind
the ejector and higher efficiency. The processes in this ejector and
influences of primary flow pulsations on the mixing processes are
described.
Abstract: The need to increase the efficiency of health care
systems is becoming an obligation, and one of area of improvement
is the discharge process. The objective of this work is to minimize
the patients discharge time (for insured patients) to be less than 50
minutes by using six sigma approach, this improvement will also:
lead to an increase in customer satisfaction, increase the number of
admissions and turnover on the rooms, increase hospital
profitability.Three different departments were considered in this
study: Female, Male, and Paediatrics. Six Sigma approach coupled
with simulation has been applied to reduce the patients discharge
time for pediatrics, female, and male departments at hospital. Upon
applying these recommendations at hospital: 60%, 80%, and 22% of
insured female, male, and pediatrics patients respectively will have
discharge time less than the upper specification time i.e. 50 min.
Abstract: Intelligent schools are those which use IT devices and
technologies as media software, hardware and networks to improve
learning process. On the other hand management improvement is
best described as the process from which managers learn and improve
their skills not only to benefit themselves but also their employing
organizations Here, we present a model Management improvement
System that has been applied on some schools and have made strict
improvement.
Abstract: In this paper, a novel LVTSCR-based device for
electrostatic discharge (ESD) protection of integrated circuits (ICs) is
designed, fabricated and characterized. The proposed device is similar
to the conventional LVTSCR but it has an embedded PMOSFET in the
anode n-well to enhance the turn on speed, the clamping capability and
the robustness. This is possible because the embedded PMOSFET
provides the sub-path of ESD discharge current. The TLP, HBM and
MM testing are carried out to verify the ESD performance of the
proposed devices, which are fabricated in 0.35um
(Bipolar-CMOS-DMOS) BCDMOS process. The device has the
robustness of 70mA/um that is higher about 60mA/um than the
LVTSCR, approximately.
Abstract: This paper discusses the performance modeling and availability analysis of Yarn Dyeing System of a Textile Industry. The Textile Industry is a complex and repairable engineering system. Yarn Dyeing System of Textile Industry consists of five subsystems arranged in series configuration. For performance modeling and analysis of availability, a performance evaluating model has been developed with the help of mathematical formulation based on Markov-Birth-Death Process. The differential equations have been developed on the basis of Probabilistic Approach using a Transition Diagram. These equations have further been solved using normalizing condition in order to develop the steady state availability, a performance measure of the system concerned. The system performance has been further analyzed with the help of decision matrices. These matrices provide various availability levels for different combinations of failure and repair rates for various subsystems. The findings of this paper are therefore, considered to be useful for the analysis of availability and determination of the best possible maintenance strategies which can be implemented in future to enhance the system performance.
Abstract: The capturing of gel electrophoresis image represents
the output of a DNA computing algorithm. Before this image is being
captured, DNA computing involves parallel overlap assembly (POA)
and polymerase chain reaction (PCR) that is the main of this
computing algorithm. However, the design of the DNA
oligonucleotides to represent a problem is quite complicated and is
prone to errors. In order to reduce these errors during the design stage
before the actual in-vitro experiment is carried out; a simulation
software capable of simulating the POA and PCR processes is
developed. This simulation software capability is unlimited where
problem of any size and complexity can be simulated, thus saving
cost due to possible errors during the design process. Information
regarding the DNA sequence during the computing process as well as
the computing output can be extracted at the same time using the
simulation software.
Abstract: In this paper we present an autoregressive model with
neural networks modeling and standard error backpropagation
algorithm training optimization in order to predict the gross domestic
product (GDP) growth rate of four countries. Specifically we propose
a kind of weighted regression, which can be used for econometric
purposes, where the initial inputs are multiplied by the neural
networks final optimum weights from input-hidden layer after the
training process. The forecasts are compared with those of the
ordinary autoregressive model and we conclude that the proposed
regression-s forecasting results outperform significant those of
autoregressive model in the out-of-sample period. The idea behind
this approach is to propose a parametric regression with weighted
variables in order to test for the statistical significance and the
magnitude of the estimated autoregressive coefficients and
simultaneously to estimate the forecasts.