Abstract: The characteristic requirement for producing
rectangular shape bottles was a uniform thickness of the plastic bottle
wall. Die shaping was a good technique which controlled the wall
thickness of bottles. An advance technology which was the finite
element method (FEM) for blowing parison to be a rectangular shape
bottle was conducted to reduce waste plastic from a trial and error
method of a die shaping and parison control method. The artificial
intelligent (AI) comprised of artificial neural network and genetic
algorithm was selected to optimize the die gap shape from the FEM
results. The application of AI technique could optimize the suitable
die gap shape for the parison blow molding which did not depend on
the parison control method to produce rectangular bottles with the
uniform wall. Particularly, this application can be used with cheap
blow molding machines without a parison controller therefore it will
reduce cost of production in the bottle blow molding process.
Abstract: Non-linear FEM calculations are indispensable when
important technical information like operating performance of a
rubber component is desired. For example rubber bumpers built into
air-spring structures may undergo large deformations under load,
which in itself shows non-linear behavior. The changing contact
range between the parts and the incompressibility of the rubber
increases this non-linear behavior further. The material
characterization of an elastomeric component is also a demanding
engineering task.
The shape optimization problem of rubber parts led to the study of
FEM based calculation processes. This type of problems was posed
and investigated by several authors. In this paper the time demand of
certain calculation methods are studied and the possibilities of time
reduction is presented.
Abstract: In order to study the aerodynamic performance of a
semi-flexible membrane wing, Fluid-Structure Interaction simulations
have been performed. The fluid problem has been modeled using
two different approaches which are the vortex panel method and the
numerical solution of the Navier-Stokes equations. Nonlinear analysis
of the structural problem is performed using the Finite Element
Method. Comparison between the two fluid solvers has been made.
Aerodynamic performance of the wing is discussed regarding its
lift and drag coefficients and they are compared with those of the
equivalent rigid wing.
Abstract: The restrained construction zoning, an important part
in the urban master plan, is a necessary planning tool to control the city
sprawl, to guarantee the reservation implementation of the various
types of protective elements, and to realize the storage of the essential
urban spatial resources. Simultaneously, owing to the diverse
constitutes of restrained construction area and the various stakeholders
involved in, its planning requires an overall consideration of all
elements from the perspective of coordination+, balance and
practicability to deal with the problems and conflicts in this process.
Taking Yangzijin Ecological Restrained Construction Area in
Yangzhou as an example, this study analyzes all the potential actors,
agencies and stakeholders in this restrained construction area, as well
as the relevant conflicts between each other. Besides, this study tries to
build up a planning procedure based on the framework of governance
theory, and proposes a possible planning method that combines
"rigidity" and "flexibility" to protect the ecological limitation
boundary, to take every interest into account, and to promote economic
development in a harmonious society.
Abstract: The concentration levels of six heavy metals (Cd, Cr,
Fe, Ni, Pb and Zn) and two mineral elements (Ca and Mg) were
determined in soil samples collected from the vicinity of two auto
mechanic workshops in Sabon-Gari, Kaduna state, Nigeria, using
Atomic Absorption Spectrometry (AAS), in order to compare the
gradation of their concentrations with distance and depth of soil from
the workshop sites. At site 1, concentrations of Lead, Chromium, Iron
and Zinc were generally found to be above the World Health
Organization limits, while those of Nickel and Cadmium fell within
the limits. Iron had the highest concentration with a range of 176.274
ppm to 489.127 ppm at depths of 5 cm to 15 cm and a distance range
of 5 m to 15 m, while the concentration of cadmium was least with a
range of 0.001 ppm to 0.008 ppm at similar depth and distance
ranges. In addition, there was more of calcium (11.521 ppm to
121.709 ppm), in all the samples, than magnesium (11.293 ppm to
21.635 ppm). Similar results were obtained for site II. The
concentrations of all the metals analyzed showed a downward
gradient with increase in depth and distance from both workshop sites
except for iron and zinc at site 2. The immediate and remote
implications of these findings on the biota are discussed.
Abstract: PLA emerged as a promising polymer because of its
property as a compostable, biodegradable thermoplastic made from
renewable sources. PLA can be polymerized from monomers
(Lactide or Lactic acid) obtained by fermentation processes from
renewable sources such as corn starch or sugarcane. For PLA
synthesis, ring opening polymerization (ROP) of Lactide monomer is
one of the preferred methods. In the literature, the technique mainly
developed for ROP of PLA is based on metal/bimetallic catalyst (Sn,
Zn and Al) or other organic catalysts in suitable solvent. However,
the PLA synthesized using such catalysts may contain trace elements
of the catalyst which may cause toxicity. This work estimated the
usefulness and drawbacks of using different catalysts as well as effect
of alternative energies and future aspects for PLA production.
Abstract: The temperature dependence of wettability (wetting
angle, Θ (T)) for Ag-based melts on graphite and Al2O3 substrates is
compared. Typical alloying effects are found, as the Ag host metal is
gradually replaced by various metallic elements. The essence of
alloying lies in the change of the electron/atom (e/a) ratio. This ratio
is also manifested in the shift of wetting angles on the same substrate.
Nevertheless, the effects are partially smeared by other
(metallurgical) factors, like the interaction between the oxygenalloying
elements and by the graphite substrate-oxygen interaction. In
contrast, such effects are not pronounced in the case of Al2O3
substrates. As a consequence, Θ(T) exhibits an opposite trend in the
case of two substrates. Crossovers of the Θ(T) curves were often
found. The positions of crossovers depend on the chemical character
and concentration of solute atoms. Segregation and epitaxial texture
formation after solidification were also observed in certain alloy
drops, especially in high concentration range. This phenomenon is
not yet explained in every detail.
Abstract: These days, the field of tissue engineering is getting
serious attention due to its usefulness. Bone tissue engineering helps
to address and sort-out the critical sized and non-healing orthopedic
problems by the creation of manmade bone tissue. We will design
and validate an efficient numerical model, which will simulate the
effective diffusivity in bone tissue engineering. Our numerical model
will be based on the finite element analysis of the diffusion-reaction
equations. It will have the ability to optimize the diffusivity, even
at multi-scale, with the variation of time. It will also have a special
feature “parametric sweep”, with which we will be able to predict
the oxygen, glucose and cell density dynamics, more accurately. We
will fix these problems by modifying the governing equations, by
selecting appropriate spatio-temporal finite element schemes and by
transient analysis.
Abstract: Since columns are the most important elements of the
structures, failure of one column in a critical location can cause a
progressive collapse. In this respect, the repair and strengthening of
columns is a very important subject to reduce the building failure and
to keep the columns capacity. Twenty columns with different
parameters is tested and analysis. Eleven typical confined reinforced
concrete (RC) columns with different types of techniques are
assessment. And also, four confined concrete columns with plastic
tube (PVC) are tested with and with four paralleling tested of
unconfined plain concrete. The techniques of confined RC columns
are mortar strengthening, Steel rings strengthening, FRP
strengthening. Moreover, the technique of confined plain concrete
(PC) column is used PVC tubes. The columns are tested under
uniaxial compressive loads studied the effect of confinement on the
structural behavior of circular RC columns. Test results for each
column are presented in the form of crack patterns, stress-strain
curves. Test results show that confining of the RC columns using
different techniques of strengthening results significant improvement
of the general behavior of the columns and can used in construction.
And also, tested confined PC columns with PVC tubes results shown
that the confined PC with PVC tubes can be used in economical
building. The theoretical model for predicted column capacity is
founded with experimental factor depends on the confined techniques
used and the strain reduction.
Abstract: Stator elements «Vane diffuser + crossover + return
channel» of stages with different specific speed were investigated by
CFD calculations. The regime parameter was introduced to present
efficiency and loss coefficient performance of all elements together.
Flow structure demonstrated advantages and disadvantages of design.
Flow separation in crossovers was eliminated by its shape
modification. Efficiency increased visibly. Calculated CFD
performances are in acceptable correlation with predicted ones by
engineering design method. The information obtained is useful for
design method better calibration.
Abstract: Solar energy is a good option among renewable
energy resources due to its easy availability and abundance. The
simplest and most efficient way to utilize solar energy is to convert it
into thermal energy and this can be done with the help of solar
collectors. The thermal performance of such collectors is poor due to
less heat transfer from the collector surface to air. In this work,
experimental investigations of single pass solar air heater having
triangular duct and provided with roughness element on the underside
of the absorber plate. V-shaped ribs are used for investigation having
three different values of relative roughness pitch (p/e) ranges from 4-
16 for a fixed value of angle of attack (α), relative roughness height
(e/Dh) and a relative gap distance (d/x) values are 60°, 0.044 and 0.60
respectively. Result shows that considerable augmentation in heat
transfer has been obtained by providing roughness.
Abstract: The use OF adhesive anchors for wooden constructions is an efficient technology to connect and design timber members in new timber structures and to rehabilitate the damaged structural members of historical buildings. Due to the lack of standard regulation in this specific area of structural design, designers’ choices are still supported by test analysis that enables knowledge, and the prediction, of the structural behaviour of glued in rod joints. The paper outlines an experimental research activity aimed at identifying the tensile resistance capacity of several new adhesive joint prototypes made of epoxy resin, steel bar and timber, Oak and Douglas Fir species. The development of new adhesive connectors has been carried out by using epoxy to glue stainless steel bars into pre-drilled holes, characterised by smooth and rough internal surfaces, in timber samples. The realization of a threaded contact surface using a specific drill bit has led to an improved bond between wood and epoxy. The applied changes have also reduced the cost of the joints’ production. The paper presents the results of this parametric analysis and a Finite Element analysis that enables identification and study of the internal stress distribution in the proposed adhesive anchors.
Abstract: Interaction between human, location and activity
defines space. In the framework of these relations, space is a
container for current specifications in relations of the 3 mentioned
elements. The change of land utility considered with average
performance range, urban regulations, society requirements etc. will
provide welfare and comfort for citizens. From an engineering view it
is fundamental that choosing a proper location for a specific civil
activity requires evaluation of locations from different perspectives.
The debate of desirable establishment of municipal service elements
in urban regions is one of the most important issues related to urban
planning. In this paper, the research type is applicable based on goal,
and is descriptive and analytical based on nature. Initially existing
terminals in Esfahan are surveyed and then new locations are
presented based on evaluated criteria. In order to evaluate terminals
based on the considered factors, an AHP model is used at first to
estimate weight of different factors and then existing and suggested
locations are evaluated using Arc GIS software and AHP model
results. The results show that existing bus terminals are located in
fairly proper locations. Further results of this study suggest new
locations to establish terminals based on urban criteria.
Abstract: The aim of this study is to develop an anterior lumbar
interbody fusion (ALIF) PEEK cage suitable for Korean people. In this
study, CT images were obtained from Korean male (173cm, 71kg) and
3D Korean lumbar models were reconstructed based on the CT images
to investigate anatomical characteristics. Major design parameters of
anterior lumbar interbody fusion (ALIF) PEEK Cage were selected
using the morphological measurement information of the Korean
Lumbar models. Through finite element analysis and mechanical tests,
the developed ALIFPEEK Cage prototype was compared with the
Fidji Cage (Zimmer. Inc, USA) and it was found that the ALIF
prototype showed similar and/or superior mechanical performance
compared to the FidJi Cage. Also, clinical validation for the ALIF
PEEK Cage prototype was carried out to check predictable troubles in
surgical operations. Finally, it is considered that the convenience and
stability of the prototype was clinically verified.
Abstract: A novel hybrid model of the lumbar spine, allowing
fast static and dynamic simulations of the disc pressure
and the spine mobility, is introduced in this work. Our
contribution is to combine rigid bodies, deformable finite
elements, articular constraints, and springs into a unique model
of the spine. Each vertebra is represented by a rigid body
controlling a surface mesh to model contacts on the facet
joints and the spinous process. The discs are modeled using
a heterogeneous tetrahedral finite element model. The facet
joints are represented as elastic joints with six degrees of
freedom, while the ligaments are modeled using non-linear
one-dimensional elastic elements. The challenge we tackle
is to make these different models efficiently interact while
respecting the principles of Anatomy and Mechanics.
The mobility, the intradiscal pressure, the facet joint force and
the instantaneous center of rotation of the lumbar spine are
validated against the experimental and theoretical results of
the literature on flexion, extension, lateral bending as well as
axial rotation.
Our hybrid model greatly simplifies the modeling task and
dramatically accelerates the simulation of pressure within the
discs, as well as the evaluation of the range of motion and the
instantaneous centers of rotation, without penalizing precision.
These results suggest that for some types of biomechanical
simulations, simplified models allow far easier modeling and
faster simulations compared to usual full-FEM approaches
without any loss of accuracy.
Abstract: In this paper, a nonlinear Finite Element Analysis
(FEA) was carried out using ANSYS software to build a model able
of predicting the behavior of Reinforced Concrete (RC) beams with
unbonded reinforcement. The FEA model was compared to existing
experimental data by other researchers. The existing experimental
data consisted of 16 beams that varied from structurally sound beams
to beams with unbonded reinforcement with different unbonded
lengths and reinforcement ratios. The model was able to predict the
ultimate flexural strength, load-deflection curve, and crack pattern of
concrete beams with unbonded reinforcement. It was concluded that
when the when the unbonded length is less than 45% of the span,
there will be no decrease in the ultimate flexural strength due to the
loss of bond between the steel reinforcement and the surrounding
concrete regardless of the reinforcement ratio. Moreover, when the
reinforcement ratio is relatively low, there will be no decrease in
ultimate flexural strength regardless of the length of unbond.
Abstract: Fast changing knowledge systems on the Internet can
be accessed more efficiently with the help of automatic document
summarization and updating techniques. The aim of multi-document
update summary generation is to construct a summary unfolding the
mainstream of data from a collection of documents based on the
hypothesis that the user has already read a set of previous documents.
In order to provide a lot of semantic information from the documents,
deeper linguistic or semantic analysis of the source documents were
used instead of relying only on document word frequencies to select
important concepts. In order to produce a responsive summary,
meaning oriented structural analysis is needed. To address this issue,
the proposed system presents a document summarization approach
based on sentence annotation with aspects, prepositions and named
entities. Semantic element extraction strategy is used to select
important concepts from documents which are used to generate
enhanced semantic summary.
Abstract: The increasing demand of gallium, indium and
rare-earth elements for the production of electronics, e.g. solid
state-lighting, photovoltaics, integrated circuits, and liquid crystal
displays, will exceed the world-wide supply according to current
forecasts. Recycling systems to reclaim these materials are not yet in
place, which challenges the sustainability of these technologies. This
paper proposes a multispectral imaging system as a basis for a vision
based recognition system for valuable components of electronics
waste. Multispectral images intend to enhance the contrast of images
of printed circuit boards (single components, as well as labels) for
further analysis, such as optical character recognition and entire
printed circuit board recognition. The results show, that a higher
contrast is achieved in the near infrared compared to ultraviolett and
visible light.
Abstract: In this paper, a new trend for improvement in semianalytical
method based on scale boundaries in order to solve the 2D
elastodynamic problems is provided. In this regard, only the
boundaries of the problem domain discretization are by specific subparametric
elements. Mapping functions are uses as a class of higherorder
Lagrange polynomials, special shape functions, Gauss-Lobatto-
Legendre numerical integration, and the integral form of the weighted
residual method, the matrix is diagonal coefficients in the equations
of elastodynamic issues. Differences between study conducted and
prior research in this paper is in geometry production procedure of
the interpolation function and integration of the different is selected.
Validity and accuracy of the present method are fully demonstrated
through two benchmark problems which are successfully modeled
using a few numbers of DOFs. The numerical results agree very well
with the analytical solutions and the results from other numerical
methods.
Abstract: This paper presents the details of a numerical study of
buckling and post buckling behaviour of laminated carbon fiber
reinforced plastic (CFRP) thin-walled cylindrical shell under axial
compression using asymmetric meshing technique (AMT) by
ABAQUS. AMT is considered to be a new perturbation method to
introduce disturbance without changing geometry, boundary
conditions or loading conditions. Asymmetric meshing affects both
predicted buckling load and buckling mode shapes. Cylindrical shell
having lay-up orientation [0^o/+45^o/-45^o/0^o] with radius to thickness
ratio (R/t) equal to 265 and length to radius ratio (L/R) equal to 1.5 is
analysed numerically. A series of numerical simulations
(experiments) are carried out with symmetric and asymmetric
meshing to study the effect of asymmetric meshing on predicted
buckling behaviour. Asymmetric meshing technique is employed in
both axial direction and circumferential direction separately using
two different methods, first by changing the shell element size and
varying the total number elements, and second by varying the shell
element size and keeping total number of elements constant. The
results of linear analysis (Eigenvalue analysis) and non-linear
analysis (Riks analysis) using symmetric meshing agree well with
analytical results. The results of numerical analysis are presented in
form of non-dimensional load factor, which is the ratio of buckling
load using asymmetric meshing technique to buckling load using
symmetric meshing technique. Using AMT, load factor has about 2%
variation for linear eigenvalue analysis and about 2% variation for
non-linear Riks analysis. The behaviour of load end-shortening curve
for pre-buckling is same for both symmetric and asymmetric meshing
but for asymmetric meshing curve behaviour in post-buckling
becomes extraordinarily complex. The major conclusions are:
different methods of AMT have small influence on predicted
buckling load and significant influence on load displacement curve
behaviour in post buckling; AMT in axial direction and AMT in
circumferential direction have different influence on buckling load
and load displacement curve in post-buckling.