Abstract: An experimental study was performed to investigate
the behavior and strength of proposed technique to connect
reinforced concrete (RC) beam to steel or composite columns. This
approach can practically be used in several types of building
construction. In this technique, the main beam of the frame consists
of a transfer part (part of beam; Tr.P) and a common reinforcement
concrete beam. The transfer part of the beam is connected to the
column, whereas the rest of the beam is connected to the transfer part
from each side. Four full-scale beam-column connections were tested
under static loading. The test parameters were the length of the
transfer part and the column properties. The test results show that
using of the transfer part technique leads to modify the deformation
capabilities for the RC beam and hence it increases its resistance
against failure. Increase in length of the transfer part did not
necessarily indicate an enhanced behavior. The test results contribute
to the characterization of the connection behavior between RC beam -
steel column and can be used to calibrate numerical models for the
simulation of this type of connection.
Abstract: Catalytic combustion of methane is imperative due to
stability of methane at low temperature. Methane (CH4), therefore,
remains unconverted in vehicle exhausts thereby causing greenhouse
gas GHG emission problem. In this study, heterogeneous catalysts of
palladium with bio-char (2 wt% Pd/Bc) and Al2O3 (2wt% Pd/ Al2O3)
supports were prepared by incipient wetness impregnation and then
subsequently tested for catalytic combustion of CH4. Support-porous
heterogeneous catalytic combustion (HCC) material were selected
based on factors such as surface area, porosity, thermal stability,
thermal conductivity, reactivity with reactants or products, chemical
stability, catalytic activity, and catalyst life. Sustainable and
renewable support-material of bio-mass char derived from palm shell
waste material was compared with those from the conventional
support-porous materials. Kinetic rate of reaction was determined for
combustion of methane on Palladium (Pd) based catalyst with Al2O3
support and bio-char (Bc). Material characterization was done using
TGA, SEM, and BET surface area. The performance test was
accomplished using tubular quartz reactor with gas mixture ratio of
3% methane and 97% air. The methane porous-HCC conversion was
carried out using online gas analyzer connected to the reactor that
performed porous-HCC. BET surface area for prepared 2 wt% Pd/Bc
is smaller than prepared 2wt% Pd/ Al2O3 due to its low porosity
between particles. The order of catalyst activity based on kinetic rate
on reaction of catalysts in low temperature was 2wt%
Pd/Bc>calcined 2wt% Pd/ Al2O3> 2wt% Pd/ Al2O3>calcined 2wt%
Pd/Bc. Hence agro waste material can successfully be utilized as an
inexpensive catalyst support material for enhanced CH4 catalytic
combustion.
Abstract: Hybrid bioreactor having both suspended-growth and
attached-growth bacteria is found a novel and excellent bioreactor
system for treating the municipal wastewater containing inhibitory
substrates too. In this reactor a fraction of substrate is used by
suspended biomass and the remaining by attached biomass resulting
in the competition between the two growths for the substrate. The
combination of suspended and attached growth provides the system
with enhanced biomass concentration and sludge age more than those
in ASP. Similar to attached growth system, the hybrid bioreactor
ensures considerable efficiency for treating toxic and refractory
substances in wastewater. For the process design of hybrid bioreactor
a suitable mathematical model is required. Although various
mathematical models were developed on hybrid bioreactor in due
course of time in earlier research works, none of them was found
having a specific simplified solution of the corresponding models and
without having any drawback. To overcome this drawback authors
already developed a simplified mathematical model for process
design of a hybrid bioreactor. The present paper briefly highlights on
the various aspects of process design of an aerobic hybrid bioreactor
for the treatment of municipal wastewater.
Abstract: This paper shows an experimental testing of a small
unit for combustion of solid fuels, such as charcoal and wood logs,
that can provide electricity. One of the concepts is that the unit does
not require qualified personnel for its operation. The unit itself is
composed of two main parts. The design requires a heat producing
stove and electricity producing thermoelectric generator. After the
construction the unit was tested and the results show that the
emission release is within the legislative requirements for emission
production and environmental protection. That qualifies such unit for
indoor application.
Abstract: Despite the highly touted benefits, emerging
technologies have unleashed pervasive concerns regarding unintended
and unforeseen social impacts. Thus, those wishing to create safe and
socially acceptable products need to identify such side effects and
mitigate them prior to the market proliferation. Various methodologies
in the field of technology assessment (TA), namely Delphi, impact
assessment, and scenario planning, have been widely incorporated in
such a circumstance. However, literatures face a major limitation in
terms of sole reliance on participatory workshop activities. They
unfortunately missed out the availability of a massive untapped data
source of futuristic information flooding through the Internet. This
research thus seeks to gain insights into utilization of futuristic data,
future-oriented documents from the Internet, as a supplementary
method to generate social impact scenarios whilst capturing
perspectives of experts from a wide variety of disciplines. To this end,
network analysis is conducted based on the social keywords extracted
from the futuristic documents by text mining, which is then used as a
guide to produce a comprehensive set of detailed scenarios. Our
proposed approach facilitates harmonized depictions of possible
hazardous consequences of emerging technologies and thereby makes
decision makers more aware of, and responsive to, broad qualitative
uncertainties.
Abstract: This research has been conducted to study the method
of culture and comparing growth and biomass of Gracilaria corticata
cultured on rope and net for 50 days through two treatments (first
treatment: culture of alga on net and the second treatment: culture of
alga on rope and each treatment was repeated by four cases). During
culture period, the water of aquariums was replaced once every two
days for 40-50%. Also, 0.3-0.5 grams of urea fertilizer was added to
the culture environment for fertilization. Moreover, some of the
environmental factors such as pH, salinity and temperature of the
environment were measured on a daily basis. During the culture
period, extent of longitudinal growth of the species of both treatments
was equal. The said length was reached from 8-10 cm to 10.5-13 cm
accordingly. The resulted weight in repetitions of the first treatment
was higher than that of the second treatment in such a way as in the
first treatment, its weight reached from 10 grams to 21.119 grams and
in the second treatment, its weight reached from 10 grams to 17.663
grams. On a whole, it may be stated that that kind of alga being
studied has a considerable growth with respect to its volume. The
results have revealed that the percentage of daily growth and wet
weight at the end of the first treatment was higher than that of the
second treatment and it was registered as 0.934, 6.072 and 811.432 in
the first treatment and 0.797, 4.990 and 758.071 in the second
treatment respectively. This difference is significant (P
Abstract: The development of allometric models is crucial to
accurate forest biomass/carbon stock assessment. The aim of this
study was to develop a set of biomass prediction models that will
enable the determination of total tree aboveground biomass for
savannah woodland area in Niger State, Nigeria. Based on the data
collected through biometric measurements of 1816 trees and
destructive sampling of 36 trees, five species specific and one site
specific models were developed. The sample size was distributed
equally between the five most dominant species in the study site
(Vitellaria paradoxa, Irvingia gabonensis, Parkia biglobosa,
Anogeissus leiocarpus, Pterocarpus erinaceous). Firstly, the
equations were developed for five individual species. Secondly these
five species were mixed and were used to develop an allometric
equation of mixed species. Overall, there was a strong positive
relationship between total tree biomass and the stem diameter. The
coefficient of determination (R2 values) ranging from 0.93 to 0.99 P
< 0.001 were realised for the models; with considerable low standard
error of the estimates (SEE) which confirms that the total tree above
ground biomass has a significant relationship with the dbh. F-test
values for the biomass prediction models were also significant at p
Abstract: Robotic surgery is used to enhance minimally invasive
surgical procedure. It provides greater degree of freedom for surgical
tools but lacks of haptic feedback system to provide sense of touch to
the surgeon. Surgical robots work on master-slave operation, where
user is a master and robotic arms are the slaves. Current, surgical
robots provide precise control of the surgical tools, but heavily rely
on visual feedback, which sometimes cause damage to the inner
organs. The goal of this research was to design and develop a realtime
Simulink based robotic system to study force feedback
mechanism during instrument-object interaction. Setup includes three
VelmexXSlide assembly (XYZ Stage) for three dimensional
movement, an end effector assembly for forceps, electronic circuit for
four strain gages, two Novint Falcon 3D gaming controllers,
microcontroller board with linear actuators, MATLAB and Simulink
toolboxes. Strain gages were calibrated using Imada Digital Force
Gauge device and tested with a hard-core wire to measure
instrument-object interaction in the range of 0-35N. Designed
Simulink model successfully acquires 3D coordinates from two
Novint Falcon controllers and transfer coordinates to the XYZ stage
and forceps. Simulink model also reads strain gages signal through
10-bit analog to digital converter resolution of a microcontroller
assembly in real time, converts voltage into force and feedback the
output signals to the Novint Falcon controller for force feedback
mechanism. Experimental setup allows user to change forward
kinematics algorithms to achieve the best-desired movement of the
XYZ stage and forceps. This project combines haptic technology
with surgical robot to provide sense of touch to the user controlling
forceps through machine-computer interface.
Abstract: The detection of moving objects from a video image
sequences is very important for object tracking, activity recognition,
and behavior understanding in video surveillance.
The most used approach for moving objects detection / tracking is
background subtraction algorithms. Many approaches have been
suggested for background subtraction. But, these are illumination
change sensitive and the solutions proposed to bypass this problem
are time consuming.
In this paper, we propose a robust yet computationally efficient
background subtraction approach and, mainly, focus on the ability to
detect moving objects on dynamic scenes, for possible applications in
complex and restricted access areas monitoring, where moving and
motionless persons must be reliably detected. It consists of three
main phases, establishing illumination changes invariance,
background/foreground modeling and morphological analysis for
noise removing.
We handle illumination changes using Contrast Limited Histogram
Equalization (CLAHE), which limits the intensity of each pixel to
user determined maximum. Thus, it mitigates the degradation due to
scene illumination changes and improves the visibility of the video
signal. Initially, the background and foreground images are extracted
from the video sequence. Then, the background and foreground
images are separately enhanced by applying CLAHE.
In order to form multi-modal backgrounds we model each channel
of a pixel as a mixture of K Gaussians (K=5) using Gaussian Mixture
Model (GMM). Finally, we post process the resulting binary
foreground mask using morphological erosion and dilation
transformations to remove possible noise.
For experimental test, we used a standard dataset to challenge the
efficiency and accuracy of the proposed method on a diverse set of
dynamic scenes.
Abstract: In this paper, effects of using Alumina-water
nanofluid on the rate of heat transfer have been investigated
numerically. Physical model is a square enclosure with insulated top
and bottom horizontal walls, while the vertical walls are kept at
different constant temperatures. Two appropriate models are used to
evaluate the viscosity and thermal conductivity of nanofluid. The
governing stream-vorticity equations are solved using a second order
central finite difference scheme, coupled to the conservation of mass
and energy. The study has been carried out for the Richardson
number 0.1 to 10 and the solid volume fraction 0 to 0.04. Results are
presented by isotherms lines, average Nusselt number and normalized
Nusselt number in different range of φ and Ri for forced, combined
and natural convection dominated regime. It is found that higher heat
transfer rate is predicted when the effects of nanoparticle is taken into
account.
Abstract: This paper presents two techniques, local feature
extraction using image spectrum and low frequency spectrum
modelling using GMM to capture the underlying statistical
information to improve the performance of face recognition
system. Local spectrum features are extracted using overlap sub
block window that are mapped on the face image. For each of this
block, spatial domain is transformed to frequency domain using
DFT. A low frequency coefficient is preserved by discarding high
frequency coefficients by applying rectangular mask on the
spectrum of the facial image. Low frequency information is non-
Gaussian in the feature space and by using combination of several
Gaussian functions that has different statistical properties, the best
feature representation can be modelled using probability density
function. The recognition process is performed using maximum
likelihood value computed using pre-calculated GMM components.
The method is tested using FERET datasets and is able to achieved
92% recognition rates.
Abstract: Natural hydrocarbon seepage has helped petroleum
exploration as a direct indicator of gas and/or oil subsurface
accumulations. Surface macro-seeps are generally an indication of a
fault in an active Petroleum Seepage System belonging to a Total
Petroleum System. This paper describes a case study in which
multiple analytical techniques were used to identify and characterize
trace petroleum-related hydrocarbons and other volatile organic
compounds in groundwater samples collected from Sousse aquifer
(Central Tunisia). The analytical techniques used for analyses of
water samples included gas chromatography-mass spectrometry (GCMS),
capillary GC with flame-ionization detection, Compound
Specific Isotope Analysis, Rock Eval Pyrolysis. The objective of the
study was to confirm the presence of gasoline and other petroleum
products or other volatile organic pollutants in those samples in order
to assess the respective implication of each of the potentially
responsible parties to the contamination of the aquifer. In addition,
the degree of contamination at different depths in the aquifer was also
of interest. The oil and gas seeps have been investigated using
biomarker and stable carbon isotope analyses to perform oil-oil and
oil-source rock correlations. The seepage gases are characterized by
high CH4 content, very low δ13CCH4 values (-71,9 ‰) and high
C1/C1–5 ratios (0.95–1.0), light deuterium–hydrogen isotope ratios (-
198 ‰) and light δ13CC2 and δ13CCO2 values (-23,8‰ and-23,8‰
respectively) indicating a thermogenic origin with the contribution of
the biogenic gas. An organic geochemistry study was carried out on
the more ten oil seep samples. This study includes light hydrocarbon
and biomarkers analyses (hopanes, steranes, n-alkanes, acyclic
isoprenoids, and aromatic steroids) using GC and GC-MS. The
studied samples show at least two distinct families, suggesting two
different types of crude oil origins: the first oil seeps appears to be
highly mature, showing evidence of chemical and/or biological
degradation and was derived from a clay-rich source rock deposited
in suboxic conditions. It has been sourced mainly by the lower
Fahdene (Albian) source rocks. The second oil seeps was derived
from a carbonate-rich source rock deposited in anoxic conditions,
well correlated with the Bahloul (Cenomanian-Turonian) source rock.
Abstract: This study estimates the seismic demands of tall
buildings with central symmetric setbacks by using nonlinear time
history analysis. Three setback structures, all 60-story high with
setback in three levels, are used for evaluation. The effects of
irregularities occurred by setback are evaluated by determination of
global-drift, story-displacement and story drift. Story-displacement is
modified by roof displacement and first story displacement and story
drift is modified by global drift. All results are calculated at the
center of mass and in x and y direction. Also the absolute values of
these quantities are determined. The results show that increasing of
vertical irregularities increases the global drift of the structure and
enlarges the deformations in the height of the structure. It is also
observed that the effects of geometry irregularity in the seismic
deformations of setback structures are higher than those of mass
irregularity.
Abstract: Evaluated nuclear decay data for the 217Po nuclide is
presented in the present work. These data include recommended
values for the half-life T1/2, α-, β-- and γ-ray emission energies and
probabilities. Decay data from 221Rn α and 217Bi β—decays are
presented. Q(α) has been updated based on the recent published work
of the Atomic Mass Evaluation AME2012. In addition, the logft
values were calculated using the Logft program from the ENSDF
evaluation package. Moreover, the total internal conversion electrons
and the K-shell to L-shell and L-shell to M-shell and to N-shell
conversion electrons ratios K/L, L/M and L/N have been calculated
using Bricc program. Meanwhile, recommendation values or the
multi-polarities have been assigned based on recently measurement
yield a better intensity balance at the 254 keV and 264 keV gamma
transitions.
Abstract: In this research paper were investigated the main
regularities of a radical bromination reaction of decalin. There had
been studied the temperature effect, durations of reaction, frequency
rate of process, a ratio of initial components, type and number of the
initiator on decalin bromination degree.
There were specified optimum conditions of synthesis of a
perbromodecalin by the method of a decalin bromination. There are
developed the technological flowchart of receiving a
perbromodecalin and the mass balance of process on the first and the
subsequent loadings of components.
The results of research of antibacterial and antifungal activity of
synthesized bromoderivatives have been represented.
Abstract: Zinc oxide (ZnO) is one of the light emitting materials in ultraviolet (UV) region. In addition, ZnO nanostructures are also attracting increasing research interest as buildingblocks for UV optoelectronic applications. We have succeeded in synthesizing vertically-aligned ZnO nanostructures by laser interference patterning, which is catalyst-free and non-contact technique. In this study, vertically-aligned ZnO nanowall arrays were synthesized using two-beam interference. The maximum height and average thickness of the ZnO nanowalls were about 4.5µm and 200 nm, respectively.UV lasing from a piece of the ZnO nanowall was obtained under the third harmonic of a Q-switched Nd:YAG laser excitation, and the estimated threshold power density for lasing was about 150 kW/cm2. Furthermore, UV lasing from the vertically-aligned ZnO nanowall was also achieved. The results indicate that ZnO nanowalls can be applied to random laser.
Abstract: Nowadays, it is a globalization era which social media
plays an important role to the lifestyle as an information source, tools
to connect people together and etc. This research is object to find out
about the significant level of the social media as a distribution
channel to the agriculture product of Thailand. In this research, the
agriculture product is the Rice Berry which is the cross-bred unmilled
rice producing dark violet grain, is a combination of Hom Nin Rice
and Thai Jasmine/ Fragrant Rice 105. Rice Berry has a very high
nutrition and nice aroma so the product is in the growth stage of the
product cycle. The problem for the Rice Berry product in Thailand is
the production and the distribution channel. This study is to confirm
that the social media is another option as the distribution channel for
the product which is not a mass production product. This will be the
role model for the other niche market product to select the
distribution channel.
Abstract: There has been a significant decline in active travel
and a massive increase in the use of car dependent travel in many
countries during the past two decades. Evidential risks for people’s
physical and mental health problems are correlated with this
increased use of motorized travel. These health related problems
range from overweight and obesity to increased air pollution. In
response to these rising concerns health professionals, traffic planers,
local authorities and others have introduced a variety of initiatives to
counterbalance the dominance of cars for daily journeys.
However, the nature of travel behavior change interventions,
which aim to reduce car use, are very complex and challenging
regarding their interactions with human behavior. To change travel
behavior at least two aspects have to be taken into consideration.
First, how to alter attitudes and perceptions toward the sustainable
and healthy modes of travel, in competition with experiences of
private car use. And second, how to make these behavior change
processes irreversible and sustainable. There are no comprehensive
models available to guide policy interventions to increase the level of
success of travel behavior change interventions across both these
dimensions.
A comprehensive theoretical framework is required in the effort to
optimize how to facilitate and guide the processes of data collection
and analysis to achieve the best possible guidelines for policy
makers. Regarding the gaps in the travel behavior change research
literature, this paper attempted to identify and suggest a
multidimensional framework in order to facilitate planning the
implemented travel behavior change interventions. A structured
mixed-method model is suggested to improve the analytic power of
the results according to the complexity of human behavior.
In order to recognize people’s attitudes towards a specific travel
mode, the Theory of Planned Behavior (TPB) was operationalized.
But in order to capture decision making processes the Transtheoretical
model of Behavior Change (TTM) was also used.
Consequently, the combination of these two theories (TTM and TPB)
has resulted in a synthesis with appropriate concepts to identify and
design an implemented travel behavior change interventions.
Abstract: China is currently the world's largest producer and distributor of electric bicycle (e-bike). The increasing number of e-bikes on the road is accompanied by rising injuries and even deaths of e-bike drivers. Therefore, there is a growing need to improve the safety structure of e-bikes. This 3D frictionless contact analysis is a preliminary, but necessary work for further structural design improvement of an e-bike. The contact analysis between e-bike and the ground was carried out as follows: firstly, the Penalty method was illustrated and derived from the simplest spring-mass system. This is one of the most common methods to satisfy the frictionless contact case; secondly, ANSYS static analysis was carried out to verify finite element (FE) models with contact pair (without friction) between e-bike and the ground; finally, ANSYS transient analysis was used to obtain the data of the penetration p(u) of e-bike with respect to the ground. Results obtained from the simulation are as estimated by comparing with that from theoretical method. In the future, protective shell will be designed following the stability criteria and added to the frame of e-bike. Simulation of side falling of the improvedsafety structure of e-bike will be confirmed with experimental data.
Abstract: A Disaster Management System (DMS) is very important for countries with multiple disasters, such as Chile. In the world (also in Chile)different disasters (earthquakes, tsunamis, volcanic eruption, fire or other natural or man-made disasters) happen and have an effect on the population. It is also possible that two or more disasters occur at the same time. This meansthata multi-risk situation must be mastered. To handle such a situation a Decision Support System (DSS) based on multiagents is a suitable architecture. The most known DMSs are concernedwith only a singledisaster (sometimes thecombination of earthquake and tsunami) and often with a particular disaster. Nevertheless, a DSS helps for a better real-time response. Analyze the existing systems in the literature and expand them for multi-risk disasters to construct a well-organized system is the proposal of our work. The here shown work is an approach of a multi-risk system, which needs an architecture and well defined aims. In this moment our study is a kind of case study to analyze the way we have to follow to create our proposed system in the future.