Abstract: In the present work, a study has been made on the combination of the electrical discharge machining (EDM) with ultrasonic vibrations to improve the machining efficiency. In experiments the graphite used as tool electrode and material of workpiece was AISIH13 tool steel. The parameters such as discharge peak current and pulse duration were changed to explore their effect on the material removal rate (MRR), relative tool wear ratio (TWR) and surface roughness. From the experimental result it can be seen that ultrasonic vibration of the workpiece can significantly reduces the inactive pulses and improves the stability of process. It was found that ultrasonic assisted EDM (US-EDM) is effective in attaining a high material removal rate (MRR) in finishing regime.
Abstract: This study was conducted published to investigate
there liability of the equation pressure-impulse (PI) reinforced
concrete column inprevious studies. Equation involves three different
levels of damage criteria known as D =0. 2, D =0. 5 and D =0. 8.The
damage criteria known as a minor when 0-0.2, 0.2-0.5is known as
moderate damage, high damage known as 0.5-0.8, and 0.8-1 of the
structure is considered a failure. In this study, two types of reliability
analyzes conducted. First, using pressure-impulse equation with
different parameters. The parameters involved are the concrete
strength, depth, width, and height column, the ratio of longitudinal
reinforcement and transverse reinforcement ratio. In the first analysis
of the reliability of this new equation is derived to improve the
previous equations. The second reliability analysis involves three
types of columns used to derive the PI curve diagram using the
derived equation to compare with the equation derived from other
researchers and graph minimum standoff versus weapon yield
Federal Emergency Management Agency (FEMA). The results
showed that the derived equation is more accurate with FEMA
standards than previous researchers.
Abstract: There are only limited studies that directly correlate
the increase in reinforced concrete (RC) panel structural capacities in
resisting the blast loads with different RC panel structural properties
in terms of blast loading characteristics, RC panel dimensions, steel
reinforcement ratio and concrete material strength. In this paper,
numerical analyses of dynamic response and damage of the one-way
RC panel to blast loads are carried out using the commercial software
LS-DYNA. A series of simulations are performed to predict the blast
response and damage of columns with different level and magnitude
of blast loads. The numerical results are used to develop pressureimpulse
(P-I) diagrams of one-way RC panels. Based on the
numerical results, the empirical formulae are derived to calculate the
pressure and impulse asymptotes of the P-I diagrams of RC panels.
The results presented in this paper can be used to construct P-I
diagrams of RC panels with different concrete and reinforcement
properties. The P-I diagrams are very useful to assess panel capacities
in resisting different blast loads.
Abstract: Type 2 diabetes mellitus (T2DM) is a complex
metabolic disorder that characterized by the presence of high glucose
in blood that cause from insulin resistance and insufficiency due to
deterioration β-cell Langerhans functions. T2DM is commonly
caused by the combination of inherited genetic variations as well as
our own lifestyle. Metallothionein (MT) is a known cysteine-rich
protein responsible in helping zinc homeostasis which is important in
insulin signaling and secretion as well as protection our body from
reactive oxygen species (ROS). MT scavenged ROS and free
radicals in our body happen to be one of the reasons of T2DM and its
complications. The objective of this study was to investigate the
association of MT1A and MT2A polymorphisms between T2DM and
control subjects among Malay populations. This study involved 150
T2DM and 120 Healthy individuals of Malay ethnic with mixed
genders. The genomic DNA was extracted from buccal cells and
amplified for MT1A and MT2A loci; the 347bp and 238bp banding
patterns were respectively produced by mean of the Polymerase
Chain Reaction (PCR). The PCR products were digested with Mlucl
and Tsp451 restriction enzymes respectively and producing
fragments lengths of (158/189/347bp) and (103/135/238bp)
respectively. The ANOVA test was conducted and it shown that there
was a significant difference between diabetic and control subjects for
age, BMI, WHR, SBP, FPG, HBA1C, LDL, TG, TC and family
history with (P0.05). The genotype
frequency for AA, AG and GG of MT1A polymorphisms was 72.7%,
22.7% and 4.7% in cases and 15%, 55% and 30% in control
respectively. As for MT2A, genotype frequency of GG, GC and CC
was 42.7%, 27.3% and 30% in case and 5%, 40% and 55% for
control respectively. Both polymorphisms show significant difference
between two investigated groups with (P=0.000). The Post hoc test
was conducted and shows a significant difference between the
genotypes within each polymorphism (P=0. 000). The MT1A and
MT2A polymorphisms were believed to be the reliable molecular
markers to distinguish the T2DM subjects from healthy individuals in
Malay populations.
Abstract: We present the development of a system of programs designed for the compilation and execution of applications for handheld computers. In introduction we describe the purpose of the project and its components. The next two paragraphs present the first two components of the project (the scanner and parser generators). Then we describe the Object Pascal compiler and the virtual machines for Windows and Palm OS. In conclusion we emphasize the ways in which the project can be extended.
Abstract: Forming a legal culture among citizens is a
complicated and lengthy process, influencing all spheres of social
life. It includes promoting justice, learning rights and duties, the
introduction of juridical norms and knowledge, and also a process of
developing a system of legal acts and constitutional norms. Currently,
the evaluative and emotional influence of attempts to establish a legal
culture among the citizens of Kazakhstan is limited by real legal
practice. As a result, the values essential to a sound civil society are
absent from the consciousness of the Kazakh people who are thus, in
turn, not able to develop respect for these values. One of the
disadvantages of the modern Kazakh educational system is a
tendency to underrate the actual forces shaping the worldview of
Kazakh youths. The mass-media, which are going through a
personnel crisis, cannot provide society with the legal and political
information necessary to form the sort of legal culture required for a
true civil society.
Abstract: A new code synchronization algorithm is proposed in
this paper for the secondary cell-search stage in wideband CDMA
systems. Rather than using the Cyclically Permutable (CP) code in the
Secondary Synchronization Channel (S-SCH) to simultaneously
determine the frame boundary and scrambling code group, the new
synchronization algorithm implements the same function with less
system complexity and less Mean Acquisition Time (MAT). The
Secondary Synchronization Code (SSC) is redesigned by splitting into
two sub-sequences. We treat the information of scrambling code group
as data bits and use simple time diversity BCH coding for further
reliability. It avoids involved and time-costly Reed-Solomon (RS)
code computations and comparisons. Analysis and simulation results
show that the Synchronization Error Rate (SER) yielded by the new
algorithm in Rayleigh fading channels is close to that of the
conventional algorithm in the standard. This new synchronization
algorithm reduces system complexities, shortens the average
cell-search time and can be implemented in the slot-based cell-search
pipeline. By taking antenna diversity and pipelining correlation
processes, the new algorithm also shows its flexible application in
multiple antenna systems.
Abstract: Load forecasting has become in recent years one of the major areas of research in electrical engineering. Most traditional forecasting models and artificial intelligence neural network techniques have been tried out in this task. Artificial neural networks (ANN) have lately received much attention, and a great number of papers have reported successful experiments and practical tests. This article presents the development of an ANN-based short-term load forecasting model with improved generalization technique for the Regional Power Control Center of Saudi Electricity Company, Western Operation Area (SEC-WOA). The proposed ANN is trained with weather-related data and historical electric load-related data using the data from the calendar years 2001, 2002, 2003, and 2004 for training. The model tested for one week at five different seasons, typically, winter, spring, summer, Ramadan and fall seasons, and the mean absolute average error for one hour-ahead load forecasting found 1.12%.
Abstract: The Internet has become an indispensable part of our lives. Witnessing recent web-based mass collaboration, e.g. Wikipedia, people are questioning whether the Internet has made fundamental changes to the society or whether it is merely a hyperbolic fad. It has long been assumed that collective action for a certain goal yields the problem of free-riding, due to its non-exclusive and non-rival characteristics. Then, thanks to recent technological advances, the on-line space experienced the following changes that enabled it to produce public goods: 1) decrease in the cost of production or coordination 2) externality from networked structure 3) production function which integrates both self-interest and altruism. However, this research doubts the homogeneity of on-line mass collaboration and argues that a more sophisticated and systematical approach is required. The alternative that we suggest is to connect the characteristics of the goal to the motivation. Despite various approaches, previous literature fails to recognize that motivation can be structurally restricted by the characteristic of the goal. First we draw a typology of on-line mass collaboration with 'the extent of expected beneficiary' and 'the existence of externality', and then we examine each combination of motivation using Benkler-s framework. Finally, we explore and connect such typology with its possible dominant participating motivation.
Abstract: The study of the variability of the postural strategies
in low back pain patients, as a criterion in evaluation of the
adaptability of this system to the environmental demands is the
purpose of this study. A cross-sectional case-control study was
performed on 21 recurrent non-specific low back pain patients and 21
healthy volunteers. The electromyography activity of Deltoid,
External Oblique (EO), Transverse Abdominis/Internal Oblique
(TrA/IO) and Erector Spine (ES) muscles of each person was
recorded in 75 rapid arm flexion with maximum acceleration.
Standard deviation of trunk muscles onset relative to deltoid muscle
onset were statistically analyzed by MANOVA . The results show
that chronic low back pain patients exhibit less variability in their
anticipatory postural adjustments (APAs) in comparison with the
control group. There is a decrease in variability of postural control
system of recurrent non-specific low back pain patients that can
result in the persistence of pain and chronicity by decreasing the
adaptability to environmental demands.
Abstract: The use of Electronic Commerce (EC)
technologies enables Small Medium Enterprises (SMEs) to improve their efficiency and competitive position. Much of the literature proposes an extensive set of benefits for
organizations that choose to adopt and implement ECommerce
systems. Factors of Business –to-business (B2B)
E-Commerce adoption and implementation have been
extensively investigated. Despite enormous attention given to encourage Small Medium Enterprises (SMEs) to adopt and
implement E-Commerce, little research has been carried out in identifying the factors of Business-to-Consumer ECommerce adoption and implementation for SMEs. To conduct the study, Tornatsky and Fleischer model was adopted
and tested in four SMEs located in Christchurch, New
Zealand. This paper explores the factors that impact the
decision and method of adoption and implementation of ECommerce
systems in automobile industry. Automobile
industry was chosen because the product they deal with i.e.
cars are not a common commodity to be sold online, despite this fact the eCommerce penetration in automobile industry is
high. The factors that promote adoption and implementation of
E-Commerce technologies are discussed, together with the
barriers. This study will help SME owners to effectively
handle the adoption and implementation process and will also
improve the chance of successful E-Commerce
implementation. The implications of the findings for
managers, consultants, and government organizations engaged in promoting E-Commerce adoption and implementation in
small businesses and future research are discussed.
Abstract: The purpose of this paper is to introduce an interactive online case-study library website developed in a national project. The design goal of the website is to provide interactive, enhanced, case-based and online educational resource for educators through the purpose and within the scope of a national project. The ADDIE instructional design model was used in the development of the website for interactive case-based library. This library is developed on a web-based platform, which is important in terms of manageability, accessibility, and updateability of data. Users are able to sort the displayed case-studies by their titles, dates, ratings, view counts, etc. The usability test is used and the expert opinion is taken for the evaluation of the website. This website is a tool to integrate technology into education. It is believed that this website will be beneficial for pre-service and in-service teachers in terms of their professional developments.
Abstract: This paper describes the design and fabrication of a clock and data recovery circuit (CDR). We propose a new clock and data recovery which is based on a 1/4-rate frequency detector (QRFD). The proposed frequency detector helps reduce the VCO frequency and is thus advantageous for high speed application. The proposed frequency detector can achieve low jitter operation and extend the pull-in range without using the reference clock. The proposed CDR was implemented using a 1/4-rate bang-bang type phase detector (PD) and a ring voltage controlled oscillator (VCO). The CDR circuit has been fabricated in a standard 0.18 CMOS technology. It occupies an active area of 1 x 1 and consumes 90 mW from a single 1.8V supply.
Abstract: Multi-loop (De-centralized) Proportional-Integral-
Derivative (PID) controllers have been used extensively in process
industries due to their simple structure for control of multivariable
processes. The objective of this work is to design multiple-model
adaptive multi-loop PID strategy (Multiple Model Adaptive-PID)
and neural network based multi-loop PID strategy (Neural Net
Adaptive-PID) for the control of multivariable system. The first
method combines the output of multiple linear PID controllers,
each describing process dynamics at a specific level of operation.
The global output is an interpolation of the individual multi-loop
PID controller outputs weighted based on the current value of the
measured process variable. In the second method, neural network
is used to calculate the PID controller parameters based on the
scheduling variable that corresponds to major shift in the process
dynamics. The proposed control schemes are simple in structure with
less computational complexity. The effectiveness of the proposed
control schemes have been demonstrated on the CSTR process,
which exhibits dynamic non-linearity.
Abstract: THEOS is the first earth observation spacecraft of Thailand which was launched on the 1st October 2008 and is currently operated by GISTDA. The transfer phase has been performed by Astrium Flight Dynamics team leading to a hand over to GISTDA teams starting mid-October 2008. The THEOS spacecraft-s orbit is LEO and has the same repetitivity (14+5/26) as the SPOT spacecraft, i.e. the same altitude of 822 km but it has a different mean local solar time (LST). Ground track maintenance manoeuvres are performed to maintain the ground track within a predefined control band around the reference ground track and the band is ±40 km for THEOS spacecraft. This paper presents the first ground track maintenance manoeuvre of THEOS spacecraft and the detailed results. In addition, it also includes one and a half year of operation as seen by GISTDA operators. It finally describes the foreseenable activities for the next orbit control manoeuvre (OCM) preparation.
Abstract: The Bayesian Optimization Algorithm (BOA) is an algorithm based on the estimation of distributions. It uses techniques from modeling data by Bayesian networks to estimating the joint distribution of promising solutions. To obtain the structure of Bayesian network, different search algorithms can be used. The key point that BOA addresses is whether the constructed Bayesian network could generate new and useful solutions (strings), which could lead the algorithm in the right direction to solve the problem. Undoubtedly, this ability is a crucial factor of the efficiency of BOA. Varied search algorithms can be used in BOA, but their performances are different. For choosing better ones, certain suitable method to present their ability difference is needed. In this paper, a greedy search algorithm and a stochastic search algorithm are used in BOA to solve certain optimization problem. A method using Kullback-Leibler (KL) Divergence to reflect their difference is described.
Abstract: The objective of this research was to find the
relationship between auspicious meaning in eastern wisdom and the
interpretation as a guideline for the design and development of
community souvenirs. The sample group included 400 customers in
Bangkok who used to buy community souvenir products. The
information was applied to design the souvenirs which were
considered for the appropriateness by 5 design specialists. The data
were analyzed to find frequency, percentage, and SD with the results
as follows. 1) The best factor referring to the auspicious meaning is
color. The application of auspicious meaning can make the value
added to the product and bring the fortune to the receivers. 2) The
effectiveness of the auspicious meaning integration on the design of
community souvenir product was in high level. When considering in
each aspect, it was found that the interpretation aspect was in high
level, the congruency of the auspicious meaning and the utility of the
product was in high level. The attractiveness and the good design
were in very high level while the potential of the value added in the
product design was in high level. The suitable application to the
design of community souvenir product was in high level.
Abstract: Stability of functionally graded beams with piezoelectric layers subjected to axial compressive load that is simply supported at both ends is studied in this paper. The displacement field of beam is assumed based on first order shear deformation beam theory. Applying the Hamilton's principle, the governing equation is established. The influences of applied voltage, dimensionless geometrical parameter, functionally graded index and piezoelectric thickness on the critical buckling load of beam are presented. To investigate the accuracy of the present analysis, a compression study is carried out with a known data.
Abstract: The major urban centers are all facing rapid growth is
most often associated with spreading urbanization, social status of the
car has also changed: it has become a commodity of mass
consumption. There are currently about 5 million and 260 cars in
Algeria (2008), this number increases every year 200,000 new cars.
These phenomena induce a demand for greater mobility and a
significant need for transport infrastructure. Faced with these
problems and development of the growing use of the automobile,
central governments and local authorities in charge of urban transport
issues are aware of the need to develop their urban transport systems
but often lack opportunities.
Urban Transport Plans (PDU) were born in reaction to the "culture
of automobile." Their existence in the world the '80s, however, they
had little success before laws on air and rational use of energy in 90
years does not alter substantially their content and make mandatory
their implementation in cities of over 100,000 inhabitants (Abroad)
[1].
The objective of this work is to use the tool and specifically
Geomatics techniques as decision support in the organization and
management of travel while taking into consideration the influence,
which will then translate by National Urban Transport Plan.
Abstract: This paper discusses the classification process for medical data. In this paper, we use the data from ACM KDDCup 2008 to demonstrate our classification process based on latent topic discovery. In this data set, the target set and outliers are quite different in their nature: target set is only 0.6% size in total, while the outliers consist of 99.4% of the data set. We use this data set as an example to show how we dealt with this extremely biased data set with latent topic discovery and noise reduction techniques. Our experiment faces two major challenge: (1) extremely distributed outliers, and (2) positive samples are far smaller than negative ones. We try to propose a suitable process flow to deal with these issues and get a best AUC result of 0.98.