Abstract: The transient hydrodynamics and thermal behaviors of
fluid flow in open-ended vertical parallel-plate porous microchannel are investigated semi-analytically under the effect of the hyperbolic
heat conduction model. The model that combines both the continuum approach and the possibility of slip at the boundary is adopted in the
study. The Effects of Knudsen number , Darcy number , and thermal relaxation time on the microchannel hydrodynamics and thermal behaviors are investigated using the hyperbolic heat
conduction models. It is found that as increases the slip in the hydrodynamic and thermal boundary condition increases. This slip in
the hydrodynamic boundary condition increases as increases. Also, the slip in the thermal boundary condition increases as
decreases especially the early stage of time.
Abstract: This paper presents the study of a variable speed wind
energy conversion system based on a Doubly Fed Induction Generator
(DFIG) based on a sliding mode control applied to achieve control of
active and reactive powers exchanged between the stator of the DFIG
and the grid to ensure a Maximum Power Point Tracking (MPPT) of
a wind energy conversion system. The proposed control algorithm is
applied to a DFIG whose stator is directly connected to the grid and
the rotor is connected to the PWM converter. To extract a maximum
of power, the rotor side converter is controlled by using a stator
flux-oriented strategy. The created decoupling control between active
and reactive stator power allows keeping the power factor close to
unity. Simulation results show that the wind turbine can operate at
its optimum energy for a wide range of wind speed.
Abstract: The systematic manipulations of shapes and sizes of
inorganic compounds greatly benefit the various application fields
including optics, magnetic, electronics, catalysis and medicine.
However shape control has been much more difficult to achieve.
Hence exploration of novel method for the preparation of differently
shaped nanoparticles is challenging research area. II-VI group of
semiconductor cadmium sulphide (CdS) nanostructure with different
morphologies (such as, acicular like, mesoporous, spherical shapes)
and of crystallite sizes vary from 11 to 16 nm were successfully
synthesized by chemical aqueous precipitation of Cd2+ ions with
homogeneously released S2- ions from decomposition of cadmium
sulphate (CdSO4) and thioacetamide (CH3CSNH2) by annealing at
different radiations (microwave, ultrasonic and sunlight) with matter
and systematic research has been done for various factors affecting
the controlled growth rate of CdS nanoparticles. The obtained
nanomaterials have been characterized by X-ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FTIR),
Thermogravometric (DSC-TGA) analysis and Scanning Electron
Microscopy (SEM). The result indicates that on increasing the
reaction time particle size increases but on increasing the molar ratios
grain size decreases.
Abstract: When consistently innovative business-models can
give companies a competitive advantage, longitudinal empirical
research, which can reflect dynamic business-model changes, has yet
to prove a definitive connection. This study consequently employs a
dynamic perspective in conjunction with innovation theory to examine
the relationship between the types of business-model innovation and
firm value. This study tries to examine various types of
business-model innovation in high-end and low-end technology
industries such as HTC and the 7-Eleven chain stores with research
periods of 14 years and 32 years, respectively. The empirical results
suggest that adopting radical business-model innovation in addition to
expanding new target markets can successfully lead to a competitive
advantage. Sustained advanced technological competences and
service/product innovation are the key successful factors in high-end
and low-end technology industry business-models respectively. In
sum up, the business-model innovation can yield a higher market value
and financial value in high-end technology industries than low-end
ones.
Abstract: Organizational innovation favors technological
innovation, but does it also influence technological innovation
persistence? This article investigates empirically the pattern of
technological innovation persistence and tests the potential impact of
organizational innovation using firm-level data from three waves of
the French Community Innovation Surveys. Evidence shows a
positive effect of organizational innovation on technological
innovation persistence, according to various measures of
organizational innovation. Moreover, this impact is more significant
for complex innovators (i.e., those who innovate in both products and
processes). These results highlight the complexity of managing
organizational practices with regard to the firm-s technological
innovation. They also add to comprehension of the drivers of
innovation persistence, through a focus on an often forgotten
dimension of innovation in a broader sense.
Abstract: Date palm (Phoenix dactylifera L.) seeds are waste streams which are considered a major problem to the food industry. They contain potentially useful protein (10-15% of the whole date-s weight). Global production, industrialisation and utilisation of dates are increasing steadily. The worldwide production of date palm fruit has increased from 1.8 million tons in 1961 to 6.9 million tons in 2005, thus from the global production of dates are almost 800.000 tonnes of date palm seeds are not currently used [1]. The current study was carried out to convert the date palm seeds into useful protein powder. Compositional analysis showed that the seeds were rich in protein and fat 5.64 and 8.14% respectively. We used several laboratory scale methods to extract proteins from seed to produce a high protein powder. These methods included simple acid or alkali extraction, with or without ultrafiltration and phenol trichloroacetic acid with acetone precipitation (Ph/TCA method). The highest protein content powder (68%) was obtained by Ph/TCA method with yield of material (44%) whereas; the use of just alkali extraction gave the lowest protein content of 8%, and a yield of 32%.
Abstract: Text categorization is the problem of classifying text documents into a set of predefined classes. After a preprocessing step the documents are typically represented as large sparse vectors. When training classifiers on large collections of documents, both the time and memory restrictions can be quite prohibitive. This justifies the application of features selection methods to reduce the dimensionality of the document-representation vector. Four feature selection methods are evaluated: Random Selection, Information Gain (IG), Support Vector Machine (called SVM_FS) and Genetic Algorithm with SVM (GA_FS). We showed that the best results were obtained with SVM_FS and GA_FS methods for a relatively small dimension of the features vector comparative with the IG method that involves longer vectors, for quite similar classification accuracies. Also we present a novel method to better correlate SVM kernel-s parameters (Polynomial or Gaussian kernel).
Abstract: In present days the area of data migration is very topical. Current tools for data migration in the area of relational database have several disadvantages that are presented in this paper. We propose a methodology for data migration of the database tables and their data between various types of relational database systems (RDBMS). The proposed methodology contains an expert system. The expert system contains a knowledge base that is composed of IFTHEN rules and based on the input data suggests appropriate data types of columns of database tables. The proposed tool, which contains an expert system, also includes the possibility of optimizing the data types in the target RDBMS database tables based on processed data of the source RDBMS database tables. The proposed expert system is shown on data migration of selected database of the source RDBMS to the target RDBMS.
Abstract: Traditionally, Yemini Sidr honey has been reported to
cure liver problems, stomach ulcers, and respiratory disorders. In this
experiment, we evaluated Yemeni Sidr honey for its ability to protect
inflammations caused by acetic acid and formalin -induced writhing,
carrageenan and histamine-induced paw oedema in experimental rat
model. Hyperpyrexia, membrane stabilizing activity, and
phytochemical screening of the honey was also examined. Yemini
Sidr Honey at (100, 200 and 500 mg/kg) exhibited a concentration
dependant inhibition of acetic acid induced and formalin induced
writhing, paw oedema induced by carrageenan & histamine, and
hyperpyrexia induced by brewer's yeast, it also inhibited membrane
stabilizing activity. Phytochemical screenings of the honey reveal the
presence of flavonoids, steroid, alkaloids, saponins and tannins. This
study suggested that Yemeni Sidr honey possess very strong antiinflammatory,
analgesic and antipyretic effects and these effects
would be a result of the phytochemicals present.
Abstract: Leonotisleonurus a shrub indigenous to Southern
Africa is widely used in traditional medicine to treat a variety of
conditions ranging from skin diseases and cough to epileptic fits and
‘heart problems’. Studies on the aqueous extract of the leaves have
indicated cycloxegenase enzyme inhibitory activity and an
antihypertensive effect.
Five methanol leaf extract fractions (MLEa - MLEe) of L.
leonurus were tested on anaesthetized normotensive male Wistar rats
(AWR) and isolated perfused working rat hearts (IWH). Fraction
MLEc (0.01mg/kg – 0.05mg/kg) induced significant increases in BP
and HR in AWR and positive chronotropic and inotropic effects in
IWH (1.0mg/ml – 5.0mg/ml). Pre-administration of atenolol
(2.0mg/kg) and prazosin (60μg/kg) significantly inhibited MLEc
effect on HR and MAP respectively in vivo, while atenolol
(7.0mg/ml) pre-perfusion significantly inhibited MLEc effect in vitro.
The hypertensive effect of MLEc is probably via β1agonism.
Results also indicate the presence of multiple cardioactive
compounds in L. leonurus.
Abstract: Ultra-low-power (ULP) circuits have received
widespread attention due to the rapid growth of biomedical
applications and Battery-less Electronics. Subthreshold region of
transistor operation is used in ULP circuits. Major research challenge
in the subthreshold operating region is to extract the ULP benefits
with minimal degradation in speed and robustness. Process, Voltage
and Temperature (PVT) variations significantly affect the
performance of subthreshold circuits. Designed performance
parameters of ULP circuits may vary largely due to temperature
variations. Hence, this paper investigates the effect of temperature
variation on device and circuit performance parameters at different
biasing voltages in the subthreshold region. Simulation results clearly
demonstrate that in deep subthreshold and near threshold voltage
regions, performance parameters are significantly affected whereas in
moderate subthreshold region, subthreshold circuits are more
immune to temperature variations. This establishes that moderate
subthreshold region is ideal for temperature immune circuits.
Abstract: The remediation of water resources pollution in
developing countries requires the application of alternative
sustainable cheaper and efficient end-of-pipe wastewater treatment
technologies. The feasibility of use of South African cheap and
abundant pine tree (Pinus patula) sawdust for development of lowcost
AC of comparable quality to expensive commercial ACs in the
abatement of water pollution was investigated. AC was developed at
optimized two-stage N2-superheated steam activation conditions in a
fixed bed reactor, and characterized for proximate and ultimate
properties, N2-BET surface area, pore size distribution, SEM, pHPZC
and FTIR. The sawdust pyrolysis activation energy was evaluated by
TGA. Results indicated that the chars prepared at 800oC and 2hrs
were suitable for development of better quality AC at 800oC and 47%
burn-off having BET surface area (1086m2/g), micropore volume
(0.26cm3/g), and mesopore volume (0.43cm3/g) comparable to
expensive commercial ACs, and suitable for water contaminants
removal. The developed AC showed basic surface functionality at
pHPZC at 10.3, and a phenol adsorption capacity that was higher than
that of commercial Norit (RO 0.8) AC. Thus, it is feasible to develop
better quality low-cost AC from (Pinus patula) sawdust using twostage
N2-steam activation in fixed-bed reactor.
Abstract: Problem Statement:Rapid technological developments of the 21st century have advanced our daily lives in various ways. Particularly in education, students frequently utilize technological resources to aid their homework and to access information. listen to radio or watch television (26.9 %) and e-mails (34.2 %) [26]. Not surprisingly, the increase in the use of technologies also resulted in an increase in the use of e-mail, instant messaging, chat rooms, mobile phones, mobile phone cameras and web sites by adolescents to bully peers. As cyber bullying occurs in the cyber space, lesser access to technologies would mean lesser cyber-harm. Therefore, the frequency of technology use is a significant predictor of cyber bullying and cyber victims. Cyber bullies try to harm the victim using various media. These tools include sending derogatory texts via mobile phones, sending threatening e-mails and forwarding confidential emails to everyone on the contacts list. Another way of cyber bullying is to set up a humiliating website and invite others to post comments. In other words, cyber bullies use e-mail, chat rooms, instant messaging, pagers, mobile texts and online voting tools to humiliate and frighten others and to create a sense of helplessness. No matter what type of bullying it is, it negatively affects its victims. Children who bully exhibit more emotional inhibition and attribute themselves more negative self-statements compared to non-bullies. Students whose families are not sympathetic and who receive lower emotional support are more prone to bully their peers. Bullies have authoritarian families and do not get along well with them. The family is the place where the children-s physical, social and psychological needs are satisfied and where their personalities develop. As the use of the internet became prevalent so did parents- restrictions on their children-s internet use. However, parents are unaware of the real harm. Studies that explain the relationship between parental attitudes and cyber bullying are scarce in literature. Thus, this study aims to investigate the relationship between cyber bullying and parental attitudes in the primary school. Purpose of Study: This study aimed to investigate the relationship between cyber bullying and parental attitudes. A second aim was to determine whether parental attitudes could predict cyber bullying and if so which variables could predict it significantly. Methods:The study had a cross-sectional and relational survey model. A demographics information form, questions about cyber bullying and a Parental Attitudes Inventory were conducted with a total of 346 students (189 females and 157 males) registered at various primary schools. Data was analysed by multiple regression analysis using the software package SPSS 16.
Abstract: Educational institutions often implement policies with
the intention of influencing how learning and teaching occur.
Generally, such policies are not as effective as their makers would
like; changing the behavior of third-level teachers proves difficult.
Nevertheless, a policy instituted in 2006 at the Dublin Institute of
Technology has met with success: each newly hired faculty member
must have a post-graduate qualification in “Learning and Teaching"
or successfully complete one within the first two years of
employment. The intention is to build teachers- knowledge about
student-centered pedagogies and their capacity to implement them.
As a result of this policy (and associated programs that support it),
positive outcomes are readily apparent. Individual teachers who have
completed the programs have implemented significant change at the
course and program levels. This paper introduces the policy,
identifies outcomes in relation to existing theory, describes research
underway, and pinpoints areas where organizational learning has
occurred.
Abstract: Explosive welding is a process which uses explosive
detonation to move the flyer plate material into the base material to
produce a solid state joint. Experimental tests have been carried out
by other researchers; have been considered to explosively welded
aluminium 7039 and steel 4340 tubes in one step. The tests have been
done using various stand-off distances and explosive ratios. Various
interface geometries have been obtained from these experiments. In
this paper, all the experiments carried out were simulated using the
finite element method. The flyer plate and collision velocities
obtained from the analysis were validated by the pin-measurement
experiments. The numerical results showed that very high localized
plastic deformation produced at the bond interface. The
Ls_dyna_971 FEM has been used for all simulation process.
Abstract: Schema matching plays a key role in many different
applications, such as schema integration, data integration, data
warehousing, data transformation, E-commerce, peer-to-peer data
management, ontology matching and integration, semantic Web,
semantic query processing, etc. Manual matching is expensive and
error-prone, so it is therefore important to develop techniques to
automate the schema matching process. In this paper, we present a
solution for XML schema automated matching problem which
produces semantic mappings between corresponding schema
elements of given source and target schemas. This solution
contributed in solving more comprehensively and efficiently XML
schema automated matching problem. Our solution based on
combining linguistic similarity, data type compatibility and structural
similarity of XML schema elements. After describing our solution,
we present experimental results that demonstrate the effectiveness of
this approach.
Abstract: Grid computing is growing rapidly in the distributed
heterogeneous systems for utilizing and sharing large-scale resources
to solve complex scientific problems. Scheduling is the most recent
topic used to achieve high performance in grid environments. It aims
to find a suitable allocation of resources for each job. A typical
problem which arises during this task is the decision of scheduling. It
is about an effective utilization of processor to minimize tardiness
time of a job, when it is being scheduled. This paper, therefore,
addresses the problem by developing a general framework of grid
scheduling using dynamic information and an ant colony
optimization algorithm to improve the decision of scheduling. The
performance of various dispatching rules such as First Come First
Served (FCFS), Earliest Due Date (EDD), Earliest Release Date
(ERD), and an Ant Colony Optimization (ACO) are compared.
Moreover, the benefit of using an Ant Colony Optimization for
performance improvement of the grid Scheduling is also discussed. It
is found that the scheduling system using an Ant Colony
Optimization algorithm can efficiently and effectively allocate jobs
to proper resources.
Abstract: A new method for color image segmentation using fuzzy logic is proposed in this paper. Our aim here is to automatically produce a fuzzy system for color classification and image segmentation with least number of rules and minimum error rate. Particle swarm optimization is a sub class of evolutionary algorithms that has been inspired from social behavior of fishes, bees, birds, etc, that live together in colonies. We use comprehensive learning particle swarm optimization (CLPSO) technique to find optimal fuzzy rules and membership functions because it discourages premature convergence. Here each particle of the swarm codes a set of fuzzy rules. During evolution, a population member tries to maximize a fitness criterion which is here high classification rate and small number of rules. Finally, particle with the highest fitness value is selected as the best set of fuzzy rules for image segmentation. Our results, using this method for soccer field image segmentation in Robocop contests shows 89% performance. Less computational load is needed when using this method compared with other methods like ANFIS, because it generates a smaller number of fuzzy rules. Large train dataset and its variety, makes the proposed method invariant to illumination noise
Abstract: Extraction of edge-end-pixels is an important step for the edge linking process to achieve edge-based image segmentation. This paper presents an algorithm to extract edge-end pixels together with their directional sensitivities as an augmentation to the currently available mathematical models. The algorithm is implemented in the Java environment because of its inherent compatibility with web interfaces since its main use is envisaged to be for remote image analysis on a virtual instrumentation platform.
Abstract: In this paper, we present the video quality measure
estimation via a neural network. This latter predicts MOS (mean
opinion score) by providing height parameters extracted from
original and coded videos. The eight parameters that are used are: the
average of DFT differences, the standard deviation of DFT
differences, the average of DCT differences, the standard deviation
of DCT differences, the variance of energy of color, the luminance
Y, the chrominance U and the chrominance V. We chose Euclidean
Distance to make comparison between the calculated and estimated
output.