Abstract: In this study, the effect of nanofluids on the pool film
boiling was experimentally investigated at saturated condition under
atmospheric pressure. For this purpose, four different water-based
nanofluids (Al2O3, SiO2, TiO2 and CuO) with 0.1% particle volume
fraction were prepared. To investigate the boiling heat transfer, a
cylindrical rod with high temperature was used. The rod heated up to
high temperatures was immersed into nanofluids. The center
temperature of rod during the cooling process was recorded by using
a K-type thermocouple. The quenching curves showed that the pool
boiling heat transfer was strongly dependent on the nanoparticle
materials. During the repetitive quenching tests, the cooling time
decreased and thus, the film boiling vanished. Consequently, the
primary reason of this was the change of the surface characteristics
due to the nanoparticles deposition on the rod-s surface.
Abstract: In this paper, a new formulation for acoustics coupled with linear elasticity is presented. The primary objective of the work is to develop a three dimensional hp adaptive finite element method code destinated for modeling of acoustics of human head. The code will have numerous applications e.g. in designing hearing protection devices for individuals working in high noise environments. The presented work is in the preliminary stage. The variational formulation has been implemented and tested on a sequence of meshes with concentric multi-layer spheres, with material data representing the tissue (the brain), skull and the air. Thus, an efficient solver for coupled elasticity/acoustics problems has been developed, and tested on high contrast material data representing the human head.
Abstract: In this paper the behavior of fixed series compensated
extra high voltage transmission lines during faults is simulated. Many
over-voltage protection schemes for series capacitors are limited in
terms of size and performance, and are easily affected by
environmental conditions. While the need for more compact and
environmentally robust equipment is required. use of series
capacitors for compensating part of the inductive reactance of long
transmission lines increases the power transmission capacity.
Emphasis is given on the impact of modern capacitor protection
techniques (MOV protection). The simulation study is performed
using MATLAB/SIMULINK®and results are given for a three phase
and a single phase to ground fault.
Abstract: This work is an attempt to use the standard Smoothed
Particle Hydrodynamics methodology for the simulation of the
complex unsteady, free-surface flow in a rotating Turgo impulse
water turbine. A comparison of two different geometries was
conducted. The SPH method due to its mesh-less nature is capable of
capturing the flow features appearing in the turbine, without
diffusion at the water/air interface. Furthermore results are compared
with a commercial CFD package (Fluent®) and the SPH algorithm
proves to be capable of providing similar results, in much less time
than the mesh based CFD program. A parametric study was also
performed regarding the turbine inlet angle.
Abstract: Recently studies in area of supply chain network
(SCN) have focused on the disruption issues in distribution systems.
Also this paper extends the previous literature by providing a new biobjective
model for cost minimization of designing a three echelon
SCN across normal and failure scenarios with considering multi
capacity option for manufacturers and distribution centers. Moreover,
in order to solve the problem by means of LINGO software, novel
model will be reformulated through a branch of LP-Metric method
called Min-Max approach.
Abstract: Obfuscation is a low cost software protection
methodology to avoid reverse engineering and re engineering of
applications. Source code obfuscation aims in obscuring the source
code to hide the functionality of the codes. This paper proposes an
Array data transformation in order to obfuscate the source code
which uses arrays. The applications using the proposed data
structures force the programmer to obscure the logic manually. It
makes the developed obscured codes hard to reverse engineer and
also protects the functionality of the codes.
Abstract: Several studies have shown the association between
ambient particulate matter (PM) and adverse health effects and
climate change, thus highlighting the need to limit the anthropogenic
sources of PM. PM Exposure is commonly monitored as mass
concentration of PM10 (particle aerodynamic diameter < 10μm) or
PM2.5 (particle aerodynamic diameter < 2.5μm), although increasing
toxicity with decreasing aerodynamic diameter has been reported due
to increased surface area and enhanced chemical reactivity with other
species. Additionally, the light scattering properties of PM increases
with decreasing size. Hence, it is important to study the chemical
characterization of finer fraction of the particulate matter and to
identify their sources so that they can be controlled appropriately to a
large extent at the sources before reaching to the receptors.
Abstract: In this study we investigate silica nanoparticle (SiO2- NP) effects on the structure and phase properties of supported lipid monolayers and bilayers, coupling surface pressure measurements, fluorescence microscopy and atomic force microscopy. SiO2-NPs typically in size range of 10nm to 100 nm in diameter are tested. Our results suggest first that lipid molecules organization depends to their nature. Secondly, lipid molecules in the vinicity of big aggregates nanoparticles organize in liquid condensed phase whereas small aggregates are localized in both fluid liquid-expanded (LE) and liquid-condenced (LC). We demonstrated also by atomic force microscopy that by measuring friction forces it is possible to get information as if nanoparticle aggregates are recovered or not by lipid monolayers and bilayers.
Abstract: This paper describes how the correct endian mode of
the TMS320C6713 DSK board can be identified. It also explains how
the TMS320C6713 DSK board can be used in the little endian and in
the big endian modes for assembly language programming in
particular and for signal processing in general. Similarly, it discusses
how crucially important it is for a user of the TMS320C6713 DSK
board to identify the mode of operation and then use it correctly
during the development stages of the assembly language
programming; otherwise, it will cause unnecessary confusion and
erroneous results as far as storing data into the memory and loading
data from the memory is concerned. Furthermore, it highlights and
strongly recommends to the users of the TMS320C6713 DSK board
to be aware of the availability and importance of various display
options in the Code Composer Studio (CCS) for correctly
interpreting and displaying the desired data in the memory. The
information presented in this paper will be of great importance and
interest to those practitioners and developers who wants to use the
TMS320C6713 DSK board for assembly language programming as
well as input-output signal processing manipulations. Finally,
examples that clearly illustrate the concept are presented.
Abstract: Sedimentation is a hydraulic phenomenon that is
emerging as a serious challenge in river engineering. When the flow
reaches a certain state that gather potential energy, it shifts the
sediment load along channel bed. The transport of such materials can
be in the form of suspended and bed loads. The movement of these
along the river course and channels and the ways in which this could
influence the water intakes is considered as the major challenges for
sustainable O&M of hydraulic structures. This could be very serious
in arid and semi-arid regions like Iran, where inappropriate watershed
management could lead to shifting a great deal of sediments into the
reservoirs and irrigation systems. This paper aims to investigate
sedimentation in the Western Canal of Dez Diversion Weir in Iran,
identifying factors which influence the process and provide ways in
which to mitigate its detrimental effects by using the SHARC
Software.
For the purpose of this paper, data from the Dezful water authority
and Dezful Hydrometric Station pertinent to a river course of about 6
Km were used.
Results estimated sand and silt bed loads concentrations to be 193
ppm and 827ppm respectively. Given the available data on average
annual bed loads and average suspended sediment loads of 165ppm
and 837ppm, there was a significant statistical difference (16%)
between the sand grains, whereas no significant difference (1.2%)
was find in the silt grain sizes. One explanation for such finding
being that along the 6 Km river course there was considerable
meandering effects which explains recent shift in the hydraulic
behavior along the stream course under investigation. The sand
concentration in downstream relative to present state of the canal
showed a steep descending curve. Sediment trapping on the other
hand indicated a steep ascending curve. These occurred because the
diversion weir was not considered in the simulation model.
Abstract: In a product development process, understanding the functional behavior of the system, the role of components in achieving functions and failure modes if components/subsystem fails its required function will help develop appropriate design validation and verification program for reliability assessment. The integration of these three issues will help design and reliability engineers in identifying weak spots in design and planning future actions and testing program. This case study demonstrate the advantage of unascertained theory described in the subjective cognition uncertainty, and then applies blind number (BN) theory in describing the uncertainty of the mechanical system failure process and the same time used the same theory in bringing out another mechanical reliability system model. The practical calculations shows the BN Model embodied the characters of simply, small account of calculation but betterforecasting capability, which had the value of macroscopic discussion to some extent.
Abstract: This paper presents a methodology towards the emulation of the electrical power consumption of the RF device during the cellular phone/handset transmission mode using the LTE technology. The emulation methodology takes the physical environmental variables and the logical interface between the baseband and the RF system as inputs to compute the emulated power dissipation of the RF device. The emulated power, in between the measured points corresponding to the discrete values of the logical interface parameters is computed as a polynomial interpolation using polynomial basis functions. The evaluation of polynomial and spline curve fitting models showed a respective divergence (test error) of 8% and 0.02% from the physically measured power consumption. The precisions of the instruments used for the physical measurements have been modeled as intervals. We have been able to model the power consumption of the RF device operating at 5MHz using homotopy between 2 continuous power consumptions of the RF device operating at the bandwidths 3MHz and 10MHz.
Abstract: This paper presents a methodology for operational and
economic characteristics based evaluation and selection of a power
plant using Graph theoretic approach. A universal evaluation index
on the basis of Operational and economics characteristics of a plant is
proposed which evaluates and ranks the various types of power plants.
The index thus obtained from the pool of operational characteristics
of the power plant attributes Digraph. The Digraph is developed
considering Operational and economics attributes of the power plants
and their relative importance for their smooth operation, installation
and commissioning and prioritizing their selection. The sensitivity
analysis of the attributes towards the objective has also been carried
out in order to study the impact of attributes over the desired outcome
i.e. the universal operational-economics index of the power plant.
Abstract: The hydraulic actuated excavator, being a non-linear
mobile machine, encounters many uncertainties. There are
uncertainties in the hydraulic system in addition to the uncertain
nature of the load. The simulation results obtained in this study show
that there is a need for intelligent control of such machines and in
particular interval type-2 fuzzy controller is most suitable for
minimizing the position error of a typical excavator-s bucket under
load variations. We consider the model parameter uncertainties such
as hydraulic fluid leakage and friction. These are uncertainties which
also depend up on the temperature and alter bulk modulus and
viscosity of the hydraulic fluid. Such uncertainties together with the
load variations cause chattering of the bucket position. The interval
type-2 fuzzy controller effectively eliminates the chattering and
manages to control the end-effecter (bucket) position with positional
error in the order of few millimeters.
Abstract: This paper demonstrates an effort of a serviceoriented
engineering department in improving the sharing and
transfer of knowledge. Although the department consist of only six
employees, but it provides services in various chemical application in
an oil and gas business. The services provided span across Asia
Pacific region mainly Indonesia, Myanmar, Vietnam, Brunei,
Thailand and Singapore. Currently there are no effective tools or
integrated systems that support the sharing or transfer and
maintenance of knowledge so the department has considered
preserving this valuable knowledge by developing a Knowledge
Management System (KMS). This paper presents the development of
a KMS to support the sharing of knowledge in a service-oriented
engineering department of an oil and gas company. The embedded
features in the KMS like blog and forum will encourage iterative
process of knowledge sharing among the employees in the
department. The information and knowledge being shared, discussed
and communicated will be then achieved for future re-use. The re-use
of the knowledge allows the department to reduce redundant efforts
in providing consistent, up-to-date and cost effective of the best
solution to the its clients.
Abstract: This paper presents a method for the optimal
allocation of Distributed generation in distribution systems. In this
paper, our aim would be optimal distributed generation allocation for
voltage profile improvement and loss reduction in distribution
network. Genetic Algorithm (GA) was used as the solving tool,
which referring two determined aim; the problem is defined and
objective function is introduced. Considering to fitness values
sensitivity in genetic algorithm process, there is needed to apply load
flow for decision-making. Load flow algorithm is combined
appropriately with GA, till access to acceptable results of this
operation. We used MATPOWER package for load flow algorithm
and composed it with our Genetic Algorithm. The suggested method
is programmed under MATLAB software and applied ETAP
software for evaluating of results correctness. It was implemented on
part of Tehran electricity distributing grid. The resulting operation of
this method on some testing system is illuminated improvement of
voltage profile and loss reduction indexes.
Abstract: For any country the project management has been a
vital part for its development. The highly competitive business world
has created tremendous pressure on the project managers to achieve
success. The pressure is derived from survival and profit building in
business organizations which compels the project managers to pursue
unethical practices. As a result unethical activities in business
projects can be found easily where situations or issues arise due to
dubious business practice, high corruption, or absolute violation of
the law. The recent spur on Commonwealth games to be organized in
New Delhi indicates towards the same. It has been seen that the
project managers mainly focus on cost, time, and quality rather than
social impact and long term effects of the project. Surprisingly the
literature as well as the practitioner-s perspective also does not
identify the role of ethics in project success. This paper identifies
ethics as the fourth most important dimension in the project based
organizations. The paper predicts that the approach of considering
ethics will result in sustainability of the project. It will increase
satisfaction and loyalty of the customers as well as create harmony,
trust, brotherhood, values and morality among the team members.
This paper is conceptual in nature as inadequate literature exists
linking the project success with an ethical approach.
Abstract: In this paper, the issue of pth moment exponential stability of stochastic recurrent neural network with distributed time delays is investigated. By using the method of variation parameters, inequality techniques, and stochastic analysis, some sufficient conditions ensuring pth moment exponential stability are obtained. The method used in this paper does not resort to any Lyapunov function, and the results derived in this paper generalize some earlier criteria reported in the literature. One numerical example is given to illustrate the main results.
Abstract: Many environment specific methods and systems for Robot Navigation exist. However vast strides in the evolution of navigation technologies and system techniques create the need for a general unified framework that is scalable, modular and dynamic. In this paper a Unified Framework for a Robust Conflict-free Robot Navigation System that can be used for either a structured or unstructured and indoor or outdoor environments has been proposed. The fundamental design aspects and implementation issues encountered during the development of the module are discussed. The results of the deployment of three major peripheral modules of the framework namely the GSM based communication module, GIS Module and GPS module are reported in this paper.
Abstract: Hierarchical high-level PNs (HHPNs) with time
versions are a useful tool to model systems in a variety of application
domains, ranging from logistics to complex workflows. This paper
addresses an application domain which is receiving more and more
attention: procedure that arranges the final inpatient charge in
payment-s office and their management. We shall prove that Petri net
based analysis is able to improve the delays during the procedure, in
order that inpatient charges could be more reliable and on time.