Abstract: Borate minerals have attracted considerable attention in the past years due to their structural chemistry and mechanical properties in several industries. Recently, increasing attention has been paid to the use of; synthetically produced magnesium borates as catalysts reinforcing material for plastics, the conversion of hydrocarbons, electro-conductive treating agent, anti-wear and anti-corrosion materials. Magnesium borates can be synthesized by several methods such as; hydrothermal and solid-state (thermal) processes. In this study the hydrothermal production method was applied at the modest temperature of 80C along with convenient crystal growth. Using MgCl2.6H2O, H3BO3, and NaOH as starting materials, 30, 60, 120, 240 minutes of reaction times were studied. After all, the crystal structure and the morphology of the products were examined by X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR). As a result the forms of Admontite and Mcallisterite minerals were synthesized.
Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: The purpose of this study was to suggest some optimal
waterfront scales around small rivers by reviewing domestic and
foreign survey reports about concept and relevant systems of the
ecological cities, analyzing the data collected from a survey about
scales and facilities of waterfront green zones around small rivers. The
questionnaire survey was conducted by sampling professional
designers, developers, the citizens living in the GunpoSanbon district
covered by no river system and the citizens living in such districts
covered by a river system. The question items were about need, uses,
scale and facilities of waterfront in common, and about satisfaction
with waterfront in case of citizen groups. In short, most of the subjects
in 5 groups preferred 10~20 wide waterfront green zone. And it is
judged that the results of this study about uses and facilities of the
waterfront green zone and its scales would provide for some basic data
useful to future waterfront green zone and urban development plans.
Abstract: This paper proposes a novel feature extraction method,
based on Discrete Wavelet Transform (DWT) and K-L Seperability
(KLS), for the classification of Functional Data (FD). This method
combines the decorrelation and reduction property of DWT and the
additive independence property of KLS, which is helpful to extraction
classification features of FD. It is an advanced approach of the
popular wavelet based shrinkage method for functional data reduction
and classification. A theory analysis is given in the paper to prove the
consistent convergence property, and a simulation study is also done
to compare the proposed method with the former shrinkage ones. The
experiment results show that this method has advantages in improving
classification efficiency, precision and robustness.
Abstract: This paper presents the results of an experimental study on the performance of a triboelectric separator of plastic mixtures used for recycling. The separator consists of four cylindrical electrodes. The principle behind the separation technique is based on the difference in the Coulomb force acting on the plastic particles after triboelectric charging. The separation of mixtures of acrylonitrile butadiene styrene (ABS) and polystyrene (PS) using this method was studied. The effects of the triboelectric charging time and applied voltage on the separation efficiency were investigated. The experimental results confirm that it is possible to obtain a high purity and recovery rate for the initial compositions considered in this study.
Abstract: Zinc borates can be used as multi-functional
synergistic additives with flame retardant additives in polymers. Zinc
borate is white, non-hygroscopic and powder type product. The most
important properties are low solubility in water and high dehydration
temperature. Zinc borates dehydrate above 290°C and anhydrous zinc
borate has thermal resistance about 400°C. Zinc borates can be
synthesized using several methods such as hydrothermal and solidstate
processes. In this study, the solid-state method was applied at
low temperatures of 600oC and 700oC using the starting materials of
ZnO and H3BO3 with several mole ratios. The reaction time was
determined as 4 hours after some preliminary experiments. After the
synthesis, the crystal structure and the morphology of the products
were examined by X-Ray Diffraction (XRD) and Fourier Transform
Infrared Spectroscopy (FT-IR). As a result the forms of ZnB4O7,
Zn3(BO3)2, ZnB2O4 were synthesized and obtained along with the
unreacted ZnO.
Abstract: There was a high rate of corrosion in Pyrolysis
Gasoline Hydrogenation (PGH) unit of Arak Petrochemical Company
(ARPC), and it caused some operational problem in this plant. A
commercial chemical had been used as anti-corrosion in the
depentanizer column overhead in order to control the corrosion rate.
Injection of commercial corrosion inhibitor caused some
operational problems such as fouling in some heat exchangers. It was
proposed to replace this commercial material with another more
effective trouble free, and well-known additive by R&D and
operation specialists.
At first, the system was simulated by commercial simulation
software in electrolytic system to specify low pH points inside the
plant. After a very comprehensive study of the situation and technical
investigations ,ammonia / monoethanol amine solution was proposed
as neutralizer or corrosion inhibitor to be injected in a suitable point
of the plant. For this purpose, the depentanizer column and its
accessories system was simulated again in case of this solution
injection.
According to the simulation results, injection of new anticorrosion
substance has no any side effect on C5 cut product and
operating conditions of the column. The corrosion rate will be
cotrolled, if the pH remains at the range of 6.5 to 8 . Aactual plant
test run was also carried out by injection of ammonia / monoethanol
amine solution at the rate of 0.6 Kg/hr and the results of iron content
of water samples and corrosion test coupons confirmed the
simulation results.
Now, ammonia / monoethanol amine solution is injected to a
suitable pint inside the plant and corrosion rate has decreased
significantly.
Abstract: The purposes of this study are 1) to study the over 20-year attempt of Mahakan fort community to negotiate with Bangkok Metropolitan Administration (BMA) to remain in their residential area belonging to the state, and 2) to apply the new social and cultural dimension between the state and the community as an alternative for local participation in keeping their residential area. This is a qualitative research, and the findings reveal that the community claimed their ancestors’ right as owners of this piece of land for over 200 years. The community, therefore, requested to take part in the preservation of land, culture and local intellect and the area management in terms of being a learning resource on the cultural road in Rattanakosin Island. However, BMA imposed the law concerning the community area relocation in Rattanakosin Island. The result of law enforcement led to the failure of the area relocation, and the hard hit on physical structure of the area including the overall deterioration of the cultural road renovated in the year 1982, the 200 years’ celebration of Bangkok. The enforcement of law by the state required the move of the community, and the landscape improvement based on the capital city plan. However, this enforcement resulted in the unending conflicts between the community and the state, and the solution of this problem was unclear. At the same time the community has spent a long time opposing the state’s action, and preparing themselves by administrating the community behind Mahakan fortress with community administrative committee under the suggestion of external organization by registering all community members, providing funds for community administration. At the meantime the state lacked the continuation of the enforcement due to political problem and BMA’s administration problem. It is, therefore, suggested that an alternative solution to this problem lie at the negotiation between the state and the community with the purpose of the collaboration between the two to develop the area under the protective law of each side.
Abstract: The Yazd-Ardakan basin in Central Iran has two separated aquifers. The shallow unconfined aquifer is supplies 40 Qanats. The deep saturated confined aquifer is the main water storage. Due to over-withdrawal, water table has been decreasing during last 25 years. Recent study shows that the shortage of the aquifer is about 16 meters and land subsidence is 0.5 - 1.2 meters. Long deep cracks are found just above the aquifer and devour the irrigation water and floods. Although the most cracks direction is NW-SE and could be compared to the main direction of YA basin, there is no direct evidence for relation between land subsidence and the huge cracks. Large-scale water pumping has been decreased the water pressure in aquifer. The pressure decline disturbed the balance and increased the pressure of overlying sediments. So porosity decreased and compaction started. Then, sediments compaction developed and made land subsidence and some huge cracks slowly.
Abstract: Loop detectors report traffic characteristics in real
time. They are at the core of traffic control process. Intuitively,
one would expect that as density of detection increases, so would
the quality of estimates derived from detector data. However, as
detector deployment increases, the associated operating and
maintenance cost increases. Thus, traffic agencies often need to
decide where to add new detectors and which detectors should
continue receiving maintenance, given their resource constraints.
This paper evaluates the effect of detector spacing on freeway
travel time estimation. A freeway section (Interstate-15) in Salt
Lake City metropolitan region is examined. The research reveals
that travel time accuracy does not necessarily deteriorate with
increased detector spacing. Rather, the actual location of detectors
has far greater influence on the quality of travel time estimates.
The study presents an innovative computational approach that
delivers optimal detector locations through a process that relies on
Genetic Algorithm formulation.
Abstract: The problem of manipulator control is a highly
complex problem of controlling a system which is multi-input, multioutput,
non-linear and time variant. In this paper some adaptive
fuzzy, and a new hybrid fuzzy control algorithm have been
comparatively evaluated through simulations, for manipulator
control. The adaptive fuzzy controllers consist of self-organizing,
self-tuning, and coarse/fine adaptive fuzzy schemes. These
controllers are tested for different trajectories and for varying
manipulator parameters through simulations. Various performance
indices like the RMS error, steady state error and maximum error are
used for comparison. It is observed that the self-organizing fuzzy
controller gives the best performance. The proposed hybrid fuzzy
plus integral error controller also performs remarkably well, given its
simple structure.
Abstract: In production of medicinal plants, seed germination is
very important problem. The treated seeds (control, hydro priming
and ZnSO4) of Cumin (Cuminum cyminum L.) were evaluated at
germination and seedling growth for tolerance to salt (NaCl and
Na2SO4) conditions at the same water potentials of 0.0, -0.3, -0.6, -
0.9 and -1.2MPa. Electrical conductivity (EC) values of the NaCl
solutions were 0.0, 6.5, 12.7, 18.4 and 23.5 dSm-1, respectively. The
objective of the study was to determine factors responsible for
germination and early seedling growth due to salt toxicity or osmotic
effect and to optimize the best priming treatment for these stress
conditions. Results revealed that germination delayed in both
solutions, having variable germination with different priming
treatments. Germination, shoot and weight, root and shoot length
were higher but mean germination time and abnormal germination
percentage were lower in NaCl than Na2SO4 at the same water
potential. The root / shoot weight and R/S length increased with
increase in osmotic potential in both NaCl and Na2SO4 solutions.
NaCl had less inhibitor effect on seedling growth than the
germination. It was concluded that inhibition of germination at the
same water potential of NaCl and Na2SO4 resulted from salt toxicity
rather than osmotic effect. Hydro priming increased germination and
seedling growth under salt stress. This protocol has practical
importance and could be recommended to farmers to achieve higher
germination and uniform emergence under field conditions.
Abstract: Emerging adulthood, the new period which is
especially prevalent in the developed or industrialized countries
during ages 18 to 29, is a new conceptualization proposed by Arnett.
Intimacy is a superordinate concept which includes intimate
interaction and intimate relationship. This study includes two
proceses which are scale development and conduction of gender
differences about markers of starting romantic intimacy among
Turkish emerging adults. In first process, Markers of Starting
Romantic Intimacy Scale, with 17 items and 5 factors, was developed
using by 220 participants. In the second step, the scale was
administered to 318 Turkish male and female emerging adults
between ages 22 and 25. Results show that there is no significant
difference between gender and total score of the scale. With respect
to gender, there are significant differences between gender and in
four subscales which are self perception, affective and cognitive
intimacy, self knowledge and romantic verbalizations. Moreover,
there is no significant relationship between gender and behavioral
intimacy subscale.
Abstract: The purpose is to study the model and characteristic of
participation of the suitable community to lead to develop permanent
water marketing in Bang Noi Floating Market, Bangkonti District,
Samutsongkhram Province. A total of 342 survey questionnaire was
administered to potential respondents. The researchers interviewed
the leader of the community. Appreciation Influence Control (AIC)
was used to talk with 20 villagers on arena. The findings revealed
that overall, most people had the middle level of the participation in
developing the durable Bang Noi Floating Market, Bangkonti,
Samutsongkhram Province and in aspects of gaining benefits from
developing it with atmosphere and a beautiful view for tourism. For
example, the landscape is beautiful with public utilities. The
participation in preserving and developing Bang Noi Floating Market
remains in the former way of life. The basic factor of person affects
to the participation of people such as age, level of education, career,
and income per month. Most participants are the original hosts that
have houses and shops located in the marketing and neighbor. These
people involve with the benefits and have the power to make a water
marketing strategy, the major role to set the information database. It
also found that the leader and the villagers play the important role in
setting a five-physical database. Data include level of information
such as position of village, territory of village, road, river, and
premises. Information of culture consists of a two-level of
information, interesting point, and Itinerary. The information occurs
from presenting and practicing by the leader and villagers in the
community.All of phases are presented for listening and investigating
database together in both the leader and villagers in the process of
participation.
Abstract: This paper addresses modeling and optimization of process parameters in powder mixed electrical discharge machining (PMEDM). The process output characteristics include metal removal rate (MRR) and electrode wear rate (EWR). Grain size of Aluminum powder (S), concentration of the powder (C), discharge current (I) pulse on time (T) are chosen as control variables to study the process performance. The experimental results are used to develop the regression models based on second order polynomial equations for the different process characteristics. Then, a genetic algorithm (GA) has been employed to determine optimal process parameters for any desired output values of machining characteristics.
Abstract: In this study, we propose a tongue diagnosis method
which detects the tongue from face image and divides the tongue area into six areas, and finally generates tongue coating ratio of each area.
To detect the tongue area from face image, we use ASM as one of the active shape models. Detected tongue area is divided into six areas
widely used in the Korean traditional medicine and the distribution of tongue coating of the six areas is examined by SVM(Support Vector
Machine). For SVM, we use a 3-dimensional vector calculated by PCA(Principal Component Analysis) from a 12-dimentional vector
consisting of RGB, HIS, Lab, and Luv. As a result, we detected the tongue area stably using ASM and found that PCA and SVM helped
raise the ratio of tongue coating detection.
Abstract: The aim of this work is to study the elastic transfer
phenomenon which takes place in the elastic scattering of 16O on 12C
at energies near the Coulomb barrier. Where, the angular distribution
decrease steadily with increasing the scattering angle, then the cross
section will increase at backward angles due to the α-transfer process.
This reaction was also studied at different energies for tracking the
nuclear rainbow phenomenon. The experimental data of the angular
distribution at these energies were compared to the calculation
predictions. The optical potential codes such as SPIVAL and
Distorted Wave Born Approximation (DWUCK5) were used in
analysis.
Abstract: This paper deals with analysis of flexural stiffness,
indentation and their energies in three point loading of sandwich
beams with composite faces from Eglass/epoxy and cores from
Polyurethane or PVC. Energy is consumed in three stages of
indentation in laminated beam, indentation of sandwich beam and
bending of sandwich beam. Theory of elasticity is chosen to present
equations for indentation of laminated beam, then these equations
have been corrected to offer better results. An analytical model has
been used assuming an elastic-perfectly plastic compressive behavior
of the foam core. Classical theory of beam is used to describe three
point bending. Finite element (FE) analysis of static indentation
sandwich beams is performed using the FE code ABAQUS. The
foam core is modeled using the crushable foam material model and
response of the foam core is experimentally characterized in uniaxial
compression.
Three point bending and indentation have been done
experimentally in two cases of low velocity and higher velocity
(quasi-impact) of loading. Results can describe response of beam in
terms of core and faces thicknesses, core material, indentor diameter,
energy absorbed, and length of plastic area in the testing. The
experimental results are in good agreement with the analytical and
FE analyses. These results can be used as an introduction for impact
loading and energy absorbing of sandwich structures.
Abstract: In this study, Friction Stir Processing (FSP) a recent grain refinement technique was employed to disperse micron-sized (2 *m) SiCp particles into aluminum alloy AA6063. The feasibility to fabricate bulk composites through FSP was analyzed and experiments were conducted at different traverse speeds and wider volumes of the specimens. Micro structural observation were carried out by employing optical microscopy test of the cross sections in both parallel and perpendicular to the tool traverse direction. Mechanical property including micro hardness was evaluated in detail at various regions on the specimen. The composites had an excellent bonding with aluminum alloy substrate and a significant increase of 30% in the micro hardness value of metal matrix composite (MMC) as to that of the base metal has observed. The observations clearly indicate that SiC particles were uniformly distributed within the aluminum matrix.
Abstract: The study of the generated defects on manufactured
parts shows the difficulty to maintain parts in their positions during
the machining process and to estimate them during the pre-process
plan. This work presents a contribution to the development of 3D
models for the optimization of the manufacturing tolerances. An
experimental study allows the measurement of the defects of part
positioning for the determination of ε and the choice of an optimal
setup of the part. An approach of 3D tolerance based on the small
displacements method permits the determination of the
manufacturing errors upstream. A developed tool, allows an
automatic generation of the tolerance intervals along the three axes.