Abstract: This paper describes the design and fabrication of a clock and data recovery circuit (CDR). We propose a new clock and data recovery which is based on a 1/4-rate frequency detector (QRFD). The proposed frequency detector helps reduce the VCO frequency and is thus advantageous for high speed application. The proposed frequency detector can achieve low jitter operation and extend the pull-in range without using the reference clock. The proposed CDR was implemented using a 1/4-rate bang-bang type phase detector (PD) and a ring voltage controlled oscillator (VCO). The CDR circuit has been fabricated in a standard 0.18 CMOS technology. It occupies an active area of 1 x 1 and consumes 90 mW from a single 1.8V supply.
Abstract: Multi-loop (De-centralized) Proportional-Integral-
Derivative (PID) controllers have been used extensively in process
industries due to their simple structure for control of multivariable
processes. The objective of this work is to design multiple-model
adaptive multi-loop PID strategy (Multiple Model Adaptive-PID)
and neural network based multi-loop PID strategy (Neural Net
Adaptive-PID) for the control of multivariable system. The first
method combines the output of multiple linear PID controllers,
each describing process dynamics at a specific level of operation.
The global output is an interpolation of the individual multi-loop
PID controller outputs weighted based on the current value of the
measured process variable. In the second method, neural network
is used to calculate the PID controller parameters based on the
scheduling variable that corresponds to major shift in the process
dynamics. The proposed control schemes are simple in structure with
less computational complexity. The effectiveness of the proposed
control schemes have been demonstrated on the CSTR process,
which exhibits dynamic non-linearity.
Abstract: This paper presents the visual control flow support of Visual Modeling and Transformation System (VMTS), which facilitates composing complex model transformations out of simple transformation steps and executing them. The VMTS Visual Control Flow Language (VCFL) uses stereotyped activity diagrams to specify control flow structures and OCL constraints to choose between different control flow branches. This work discusses the termination properties of VCFL and provides an algorithm to support the termination analysis of VCFL transformations.
Abstract: The objective of this research was to find the
relationship between auspicious meaning in eastern wisdom and the
interpretation as a guideline for the design and development of
community souvenirs. The sample group included 400 customers in
Bangkok who used to buy community souvenir products. The
information was applied to design the souvenirs which were
considered for the appropriateness by 5 design specialists. The data
were analyzed to find frequency, percentage, and SD with the results
as follows. 1) The best factor referring to the auspicious meaning is
color. The application of auspicious meaning can make the value
added to the product and bring the fortune to the receivers. 2) The
effectiveness of the auspicious meaning integration on the design of
community souvenir product was in high level. When considering in
each aspect, it was found that the interpretation aspect was in high
level, the congruency of the auspicious meaning and the utility of the
product was in high level. The attractiveness and the good design
were in very high level while the potential of the value added in the
product design was in high level. The suitable application to the
design of community souvenir product was in high level.
Abstract: Malware is software which was invented and meant for doing harms on computers. Malware is becoming a significant threat in computer network nowadays. Malware attack is not just only involving financial lost but it can also cause fatal errors which may cost lives in some cases. As new Internet Protocol version 6 (IPv6) emerged, many people believe this protocol could solve most malware propagation issues due to its broader addressing scheme. As IPv6 is still new compares to native IPv4, some transition mechanisms have been introduced to promote smoother migration. Unfortunately, these transition mechanisms allow some malwares to propagate its attack from IPv4 to IPv6 network environment. In this paper, a proof of concept shall be presented in order to show that some existing IPv4 malware detection technique need to be improvised in order to detect malware attack in dual-stack network more efficiently. A testbed of dual-stack network environment has been deployed and some genuine malware have been released to observe their behaviors. The results between these different scenarios will be analyzed and discussed further in term of their behaviors and propagation methods. The results show that malware behave differently on IPv6 from the IPv4 network protocol on the dual-stack network environment. A new detection technique is called for in order to cater this problem in the near future.
Abstract: The major urban centers are all facing rapid growth is
most often associated with spreading urbanization, social status of the
car has also changed: it has become a commodity of mass
consumption. There are currently about 5 million and 260 cars in
Algeria (2008), this number increases every year 200,000 new cars.
These phenomena induce a demand for greater mobility and a
significant need for transport infrastructure. Faced with these
problems and development of the growing use of the automobile,
central governments and local authorities in charge of urban transport
issues are aware of the need to develop their urban transport systems
but often lack opportunities.
Urban Transport Plans (PDU) were born in reaction to the "culture
of automobile." Their existence in the world the '80s, however, they
had little success before laws on air and rational use of energy in 90
years does not alter substantially their content and make mandatory
their implementation in cities of over 100,000 inhabitants (Abroad)
[1].
The objective of this work is to use the tool and specifically
Geomatics techniques as decision support in the organization and
management of travel while taking into consideration the influence,
which will then translate by National Urban Transport Plan.
Abstract: In the 21. century it comes true, that competitiveness of the firm is - to a considerable level - influenced by its participation in the chain of suppliers, customers and partners and by the way how the subject cooperates in the chain. This is valid also for new forms of enterprise such as virtual organization or virtual firm. In the first part of the paper there are determined the differences between these forms of enterprise. Another part will bring methodological framework for analysis of the factors, that influence the competitiveness of the virtual organization from spontaneity and order point of view.
Abstract: Abrasive waterjet cutting (AWJ) is a highly efficient
method for cutting almost any type of material. When holes shall be
cut the waterjet first needs to pierce the material.This paper presents a
vast experimental analysis of piercing parameters effect on piercing
time. Results from experimentation on feed rates, work piece
thicknesses, abrasive flow rates, standoff distances and water
pressure are also presented as well as studies on three methods for
dynamic piercing. It is shown that a large amount of time and
resources can be saved by choosing the piercing parameters in a
correct way. The large number of experiments puts demands on the
experimental setup. An automated experimental setup including
piercing detection is presented to enable large series of experiments
to be carried out efficiently.
Abstract: Carbon fibers are fabricated from different materials,
such as special polyacrylonitrile (PAN) fibers, rayon fibers and pitch.
Among these three groups of materials, PAN fibers are the most
widely used precursor for the manufacture of carbon fibers. The
process of fabrication carbon fibers from special PAN fibers includes
two steps; oxidative stabilization at low temperature and
carbonization at high temperatures in an inert atmosphere. Due to the
high price of raw materials (special PAN fibers), carbon fibers are
still expensive.
In the present work the main goal is making carbon fibers from
low price commercial PAN fibers with modified chemical
compositions. The results show that in case of conducting completes
stabilization process, it is possible to produce carbon fibers with
desirable tensile strength from this type of PAN fibers. To this
matter, thermal characteristics of commercial PAN fibers were
investigated and based upon the obtained results, with some changes
in conventional procedure of stabilization in terms of temperature
and time variables; the desirable conditions of complete stabilization
is achieved.
Abstract: This paper present a new method for design of power
system stabilizer (PSS) based on sliding mode control (SMC)
technique. The control objective is to enhance stability and improve
the dynamic response of the multi-machine power system. In order to
test effectiveness of the proposed scheme, simulation will be carried
out to analyze the small signal stability characteristics of the system
about the steady state operating condition following the change in
reference mechanical torque and also parameters uncertainties. For
comparison, simulation of a conventional control PSS (lead-lag
compensation type) will be carried out. The main approach is
focusing on the control performance which later proven to have the
degree of shorter reaching time and lower spike.
Abstract: Orthogonal frequency division multiplexing (OFDM)
has developed into a popular scheme for wideband digital
communications used in consumer applications such as digital broadcasting, wireless networking and broadband internet access. In
the OFDM system, carrier frequency offset (CFO) causes intercarrier
interference (ICI) which significantly degrades the system error performance. In this paper we provide an exact evaluation method for error performance analysis of arbitrary 2-D modulation OFDM systems with CFO, and analyze the effect of CFO on error performance.
Abstract: Estimation of stormwater pollutants is a pre-requisite
for the protection and improvement of the aquatic environment and
for appropriate management options. The usual practice for the
stormwater quality prediction is performed through water quality
modeling. However, the accuracy of the prediction by the models
depends on the proper estimation of model parameters. This paper
presents the estimation of model parameters for a catchment water
quality model developed for the continuous simulation of stormwater
pollutants from a catchment to the catchment outlet. The model is
capable of simulating the accumulation and transportation of the
stormwater pollutants; suspended solids (SS), total nitrogen (TN) and
total phosphorus (TP) from a particular catchment. Rainfall and water
quality data were collected for the Hotham Creek Catchment (HTCC),
Gold Coast, Australia. Runoff calculations from the developed model
were compared with the calculated discharges from the widely used
hydrological models, WBNM and DRAINS. Based on the measured
water quality data, model water quality parameters were calibrated
for the above-mentioned catchment. The calibrated parameters are
expected to be helpful for the best management practices (BMPs)
of the region. Sensitivity analyses of the estimated parameters were
performed to assess the impacts of the model parameters on overall
model estimations of runoff water quality.
Abstract: Social learning network analysis has drawn attention
for most researcher on e-learning research domain. This is due to the
fact that it has the capability to identify the behavior of student
during their social interaction inside e-learning. Normally, the social
network analysis (SNA) is treating the students' interaction merely as
node and edge with less meaning. This paper focuses on providing an
ontology structure of e-learning Moodle that can enrich the
relationships among students, as well as between the students and the
teacher. This ontology structure brings great benefit to the future
development of e-learning system.
Abstract: In contrast to existing of calculation of temperature field of a profile part a blade with convective cooling which are not taking into account multi connective in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM AND FDM) numerical methods from the point of view of a realization on the PC. The theoretical substantiation of these methods is proved by the appropriate theorems.
Abstract: Let M be an almost split quaternionic manifold on
which its almost split quaternionic structure is defined by a three
dimensional subbundle V of ( T M) T (M)
*
Ôèù and
{F,G,H} be a local basis for V . Suppose that the (global)
(1, 2) tensor field defined[V ,V ]is defined by
[V,V ] = [F,F]+[G,G] + [H,H], where [,] denotes
the Nijenhuis bracket. In ref. [7], for the almost split-hypercomplex
structureH = J α,α =1,2,3, and the Obata
connection ÔêçH
vanishes if and only if H is split-hypercomplex.
In this study, we give a prof, in particular, prove that if either
M is a split quaternionic Kaehler manifold, or if M is a splitcomplex
manifold with almost split-complex structure F , then the
vanishing [V ,V ] is equivalent to that of all the Nijenhuis brackets
of {F,G,H}. It follows that the bundle V is trivial if and only if
[V ,V ] = 0 .
Abstract: Designing modern machine tools is a complex task. A
simulation tool to aid the design work, a virtual machine, has
therefore been developed in earlier work. The virtual machine
considers the interaction between the mechanics of the machine
(including structural flexibility) and the control system. This paper
exemplifies the usefulness of the virtual machine as a tool for product
development. An optimisation study is conducted aiming at
improving the existing design of a machine tool regarding weight and
manufacturing accuracy at maintained manufacturing speed. The
problem can be categorised as constrained multidisciplinary multiobjective
multivariable optimisation. Parameters of the control and
geometric quantities of the machine are used as design variables. This
results in a mix of continuous and discrete variables and an
optimisation approach using a genetic algorithm is therefore
deployed. The accuracy objective is evaluated according to
international standards. The complete systems model shows nondeterministic
behaviour. A strategy to handle this based on statistical
analysis is suggested. The weight of the main moving parts is reduced
by more than 30 per cent and the manufacturing accuracy is
improvement by more than 60 per cent compared to the original
design, with no reduction in manufacturing speed. It is also shown
that interaction effects exist between the mechanics and the control,
i.e. this improvement would most likely not been possible with a
conventional sequential design approach within the same time, cost
and general resource frame. This indicates the potential of the virtual
machine concept for contributing to improved efficiency of both
complex products and the development process for such products.
Companies incorporating such advanced simulation tools in their
product development could thus improve its own competitiveness as
well as contribute to improved resource efficiency of society at large.
Abstract: This paper uses the radial basis function neural
network (RBFNN) for system identification of nonlinear systems.
Five nonlinear systems are used to examine the activity of RBFNN in
system modeling of nonlinear systems; the five nonlinear systems are
dual tank system, single tank system, DC motor system, and two
academic models. The feed forward method is considered in this
work for modelling the non-linear dynamic models, where the KMeans
clustering algorithm used in this paper to select the centers of
radial basis function network, because it is reliable, offers fast
convergence and can handle large data sets. The least mean square
method is used to adjust the weights to the output layer, and
Euclidean distance method used to measure the width of the Gaussian
function.
Abstract: In this paper, the strength of a stabilizer is determined when the static and fatigue multiaxial loading are applied. Stabilizer is a part of suspension system in the heavy truck for stabilizing the cabin against the vibration of the road which composes of a thin-walled tube joined to a forge component by fillet weld. The component is loaded by non proportional random sequence of torsion and bending. Residual stress of welding process is considered here for static loading. This static loading with road irregularities are applied in this study as fatigue case that can affected in the fillet welded area of this part. The stresses in the welded structure are calculated using FEA. In addition, the fatigue with multi axial loading in the fillet weld is also investigated and the critical zone of the stabilizer is specified and presented by graphs. Residual stresses that have been resulted by the thermal forces are considered in FEA. Force increasing is the element of finding the critical point of the component.
Abstract: MicroRNAs (miRNAs) are a class of non-coding
RNAs that hybridize to mRNAs and induce either translation
repression or mRNA cleavage. Recently, it has been reported that
miRNAs could possibly play an important role in human diseases. By
integrating miRNA target genes, cancer genes, miRNA and mRNA
expression profiles information, a database is developed to link
miRNAs to cancer target genes. The database provides experimentally
verified human miRNA target genes information, including oncogenes
and tumor suppressor genes. In addition, fragile sites information for
miRNAs, and the strength of the correlation of miRNA and its target
mRNA expression level for nine tissue types are computed, which
serve as an indicator for suggesting miRNAs could play a role in
human cancer. The database is freely accessible at
http://ppi.bioinfo.asia.edu.tw/mirna_target/index.html.
Abstract: The hydro-mechanical model for unsaturated soils has
been presented based on the effective stress principle taking into
account effects of drying-wetting process. The elasto-plastic
constitutive equations for stress-strain relations of the soil skeleton
have been established. A plasticity model is modified from modified
Cam-Clay model. The hardening rule has been established by
considering the isotropic consolidation paths. The effect of dryingwetting
process is introduced through the ¤ç parameter. All model
coefficients are identified in terms of measurable parameters. The
simulations from the proposed model are compared with the
experimental results. The model calibration was performed to extract
the model parameter from the experimental results. Good agreement
between the results predicted using proposed model and the
experimental results was obtained.