Abstract: This paper made an attempt to investigate the problem associated with enhancement of emulsions of light crude oil-water recovery in an oil field of Algerian Sahara. Measurements were taken through experiments using RheoStress (RS600). Factors such as shear rate, temperature and light oil concentration on the viscosity behavior were considered. Experimental measurements were performed in terms of shear stress–shear rate, yield stress and flow index on mixture of light crude oil–water. The rheological behavior of emulsion showed Non-Newtonian shear thinning behavior (Herschel-Bulkley). The experiments done in the laboratory showed the stability of some water in light crude oil emulsions form during consolidate oil recovery process. To break the emulsion using additives may involve higher cost and could be very expensive. Therefore, further research should be directed to find solution of these problems that have been encountered.
Abstract: The cables in a nuclear power plant are designed to be
used for about 40 years in safe operation environment. However, the
heat and radiation in the nuclear power plant causes the rapid
performance deterioration of cables in nuclear vessels and heat
exchangers, which requires cable lifetime estimation. The most
accurate method of estimating the cable lifetime is to evaluate the
cables in a laboratory. However, removing cables while the plant is
operating is not allowed because of its safety and cost. In this paper, a
robot system to estimate the cable lifetime in nuclear power plants is
developed and tested. The developed robot system can calculate a
modulus value to estimate the cable lifetime even when the nuclear
power plant is in operation.
Abstract: The article presents test results on the changes
occurring in sewage sludge during the process of its storage. Tests
were conducted on mechanically dehydrated sewage sludge derived
from large municipal sewage treatment plants equipped with
biological sewage treatment systems. In testing presented in the paper
the focus was on the basic fuel properties of sewage sludge: moisture
content, heat of combustion, carbon share. In the first part of the
article the overview of the issues concerning the sewage sludge
management is presented and the genesis of tests is explained.
Further in the paper, selected results of conducted tests are discussed.
Changes in tested parameters were determined in the period of a 10-
month sewage storage.
Abstract: A Laboratory-scale packed bed reactor with microbial
cellulose as the biofilm carrier was used to investigate the
denitrification of high-strength nitrate wastewater with specific
emphasis on the effect the nitrogen loading rate and hydraulic
retention time. Ethanol was added as a carbon source for
denitrification. As a result of this investigation, it was found that up
to 500 mg/l feed nitrate concentration the present system is able to
produce an effluent with nitrate content below 10 ppm at 3 h
hydraulic retention time. The highest observed denitrification rate
was 4.57 kg NO3-N/ (m3 .d) at a nitrate load of 5.64 kg NO3-
N/(m3 .d), and removal efficiencies higher than 90% were obtained
for loads up to 4.2 kg NO3-N/(m3 .d). A mass relation between COD
consumed and NO3-N removed around 2.82 was observed. This
continuous-flow bioreactor proved an efficient denitrification system
with a relatively low retention time.
Abstract: Nowadays companies strive to survive in a
competitive global environment. To speed up product
development/modifications, it is suggested to adopt a collaborative
product development approach. However, despite the advantages of
new IT improvements still many CAx systems work separately and
locally. Collaborative design and manufacture requires a product
information model that supports related CAx product data models. To
solve this problem many solutions are proposed, which the most
successful one is adopting the STEP standard as a product data model
to develop a collaborative CAx platform. However, the improvement
of the STEP-s Application Protocols (APs) over the time, huge
number of STEP AP-s and cc-s, the high costs of implementation,
costly process for conversion of older CAx software files to the STEP
neutral file format; and lack of STEP knowledge, that usually slows
down the implementation of the STEP standard in collaborative data
exchange, management and integration should be considered. In this
paper the requirements for a successful collaborative CAx system is
discussed. The STEP standard capability for product data integration
and its shortcomings as well as the dominant platforms for supporting
CAx collaboration management and product data integration are
reviewed. Finally a platform named LAYMOD to fulfil the
requirements of CAx collaborative environment and integrating the
product data is proposed. The platform is a layered platform to enable
global collaboration among different CAx software
packages/developers. It also adopts the STEP modular architecture
and the XML data structures to enable collaboration between CAx
software packages as well as overcoming the STEP standard
limitations. The architecture and procedures of LAYMOD platform
to manage collaboration and avoid contradicts in product data
integration are introduced.
Abstract: The purpose of study was to design and construction
the semi-automatic sliced ginger machine for reduce production times
in sheet and slice ginger procedure furthermore, reduced amount of
labor of slides and cutting method. Take consider into clean and safety of workers and consumers. The principle of machines, used 1
horsepower motor, rotation speed of sliced blade 967 rpm, the diameter of sliced dish 310 mm, consists of 2 blades for sheet cutting
ginger and the power from motor which transfer to rotate the sliced blade roller, rotation speed 440 rpm. The slice cutter roller was sliced
ginger from sheet ginger to line ginger. The conveyer could
adjustment level of motors, used to the beginning area that sheet
ginger was transference to the roller for sheet and sliced cutting in next process. The cover of sliced cutting had channel for 1 tuber of
ginger. The semi-automatic sliced ginger machine could produced sheet ginger 81.8 kg/h (6.2 times of labor) and line ginger 17.9 kg/h
(2.5 times of labor) compare with, labor work could produced sheet
ginger 13.2 kg/h and line ginger 7.1 kg/h, and when timekeeper, the
total times of semi auto machine 30.86 kg/h and labor 4.6 kg/h, there
for the semi auto machine was 6.7 times of labor. The semiautomatic
sliced ginger machine convenient, easy for use and
maintain, in addition to reduce fatigue of body and seriousness from
works; must be used high skill, and protection accident in slicing
procedure. Beside, machine could used with other vegetables for
example potato, carrot .etc
Abstract: In this paper challenges associated with a new
generation of Computer Science students are examined. The mode of
education in tertiary institutes has progressed slowly while the needs
of students have changed rapidly in an increasingly technological
world. The major learning paradigms and learning theories within
these paradigms are studied to find a suitable strategy for educating
modern students. These paradigms include Behaviourism,
Constructivism, Humanism and Cogntivism. Social Learning theory
and Elaboration theory are two theories that are further examined and
a survey is done to determine how these strategies will be received by
students. The results and findings are evaluated and indicate that
students are fairly receptive to a method that incorporates both Social
Learning theory and Elaboration theory, but that some aspects of all
paradigms need to be implemented to create a balanced and effective
strategy with technology as foundation.
Abstract: In this study, we sought to investigate the mercury
removal efficiency of manganese oxides from natural gas. The
fundamental studies on mercury removal with manganese oxides
sorbents were carried out in a laboratory scale fixed bed reactor at 30
°C with a mixture of methane (20%) and nitrogen gas laden with 4.8
ppb of elemental mercury. Manganese oxides with varying surface
area and crystalline phase were prepared by conventional precipitation
method in this study. The effects of surface area, crystallinity and
other metal oxides on mercury removal efficiency were investigated.
Effect of Ag impregnation on mercury removal efficiency was also
investigated. Ag supported on metal oxide such titania and zirconia as
reference materials were also used in this study for comparison. The
characteristics of mercury removal reaction with manganese oxide
was investigated using a temperature programmed desorption (TPD)
technique.
Manganese oxides showed very high Hg removal activity (about
73-93% Hg removal) for first time use. Surface area of the manganese
oxide samples decreased after heat-treatment and resulted in complete
loss of Hg removal ability for repeated use after Hg desorption in the
case of amorphous MnO2, and 75% loss of the initial Hg removal
activity for the crystalline MnO2. Mercury desorption efficiency of
crystalline MnO2 was very low (37%) for first time use and high (98%)
after second time use. Residual potassium content in MnO2 may have
some effect on the thermal stability of the adsorbed Hg species.
Desorption of Hg from manganese oxides occurs at much higher
temperatures (with a peak at 400 °C) than Ag/TiO2 or Ag/ZrO2.
Mercury may be captured on manganese oxides in the form of mercury
manganese oxide.
Abstract: Medicinal plants are most suitable crops for ecological production systems because of their role in human health and the aim of sustainable agriculture to improve ecosystem efficiency and its products quality. Calculations include energy output (contents of energy in seed) and energy inputs (consumption of fertilizers, pesticides, labor, machines, fuel and electricity). The ratio of output of the production to inputs is called the energy outputs / inputs ratio or energy efficiency. One way to quantify essential parts of agricultural development is the energy flow method. The output / input energy ratio is proposed as the most comprehensive single factor in pursuing the objective of sustainability. Sylibum marianum L. is one of the most important medicinal plants in Iran and has effective role on health of growing population in Iran. The objective of this investigation was to find out energy efficiency in conventional and low input production system of Milk thistle. This investigation was carried out in the spring of 2005 – 2007 in the Research Station of Rangelands in Hamand - Damavand region of IRAN. This experiment was done in split-split plot based on randomized complete block design with 3 replications. Treatments were 2 production systems (Conventional and Low input system) in the main plots, 3 planting time (25 of March, 4 and 14 of April) in the sub plots and 2 seed types (Improved and Native of Khoozestan) in the sub-sub plots. Results showed that in conventional production system energy efficiency, because of higher inputs and less seed yield, was less than low input production system. Seed yield was 1199.5 and 1888 kg/ha in conventional and low input systems, respectively. Total energy inputs and out puts for conventional system was 10068544.5 and 7060515.9 kcal. These amounts for low input system were 9533885.6 and 11113191.8 kcal. Results showed that energy efficiency for seed production in conventional and low input system was 0.7 and 1.16, respectively. So, milk thistle seed production in low input system has 39.6 percent higher energy efficiency than conventional production system. Also, higher energy efficiency were found in sooner planting time (25 of March) and native seed of Khoozestan.
Abstract: Scolothrips longicornis Priesner is one of the
important predators of tetranychid mites with a wide distribution
throughout Iran. Life table and population growth parameters of S.
longicornis feeding on two-spotted spider mite, Tetranychus
turkestani Ugarov & Nikolski were investigated under laboratory
condition (26±1ºC, 65±5% R.H. and 16L: 8D). To carry of these
experiments, S. longicornis collections reared on cowpea infested
with T. turkestani were prepared. The eggs with less than 24 hours
old were selected and reared. The emerged larvae feeding directly on
cowpea leaf discs which were infested with T. turkestani. Thirty
females of S. longicornis with 24 hours age were selected and
released on infested leaf discs. They replaced daily to a new leaf disc
and the laying eggs have counted. The experiment continued till the
last thrips had died. The result showed that the mean age mortality of
the adult female thrips were between 21-25 days which is nearly
equal life expectancy (ex) at the time of adult eclosion. Parameters
related to reproductive table including gross reproductive rate, net
reproductive rate, intrinsic rate of natural increase and finite rate of
increase were 48.91, 37.63, 0.26 and 2.3, respectively. Mean age per
female/day, mean fertile egg per female/day, gross hatch rate, mean
net age fertility, mean net age fecundity, net fertility rate and net
fecundity rate were 2.23, 1.76, 0.87, 13.87, 14.26, 69.1 and 78.5,
respectively. Sex ratio of offspring also recorded daily. The highest
sex ratio for females was 0.88 in first day of oviposition. The sex
ratio decreased gradually and reached under 0.46 after the day 26 and
the oviposition rate declined. Then it seems that maintenance of
rearing culture of predatory thrips for mass rearing later than 26 days
after egg-laying commence is not profitable.
Abstract: To make use of the limited amounts of water in arid
region, the Iranians developed man-made underground water
channels called qanats (kanats) .In fact, qanats may be considered as
the first long-distance water transfer system. Qanats are an ancient
water transfer system found in arid regions wherein groundwater
from mountainous areas, aquifers and sometimes from rivers, was
brought to points of re-emergence such as an oasis, through one or
more underground tunnels. The tunnels, many of which were
kilometers in length, had designed for slopes to provide gravitational
flow. The tunnels allowed water to drain out to the surface by gravity
to supply water to lower and flatter agricultural land.
Qanats have been an ancient, sustainable system facilitating the
harvesting of water for centuries in Iran, and more than 35 additional
countries of the world such as India, Arabia, Egypt, North Africa,
Spain and even to New world.
There are about 22000 qanats in Iran with 274000 kilometers of
underground conduits all built by manual labor. The amount of
water of the usable qanats of Iran produce is altogether 750 to
1000 cubic meter per second. The longest chain of qanat is
situated in Gonabad region in Khorasan province. It is 70
kilometers long. Qanats are renewable water supply systems that
have sustained agricultural settlement on the Iranian plateau for
millennia. The great advantages of Qanats are no evaporation
during transit, little seepage , no raising of the water- table and no
pollution in the area surrounding the conduits. Qanat systems
have a profound influence on the lives of the water users in Iran, and
conform to Iran-s climate. Qanat allows those living in a desert
environment adjacent to a mountain watershed to create a large oasis
in an otherwise stark environment.
This paper explains qanats structure designs, their history,
objectives causing their creation, construction materials, locations
and their importance in different times, as well as their present
sustainable role in Iran.
Abstract: The use of statistical data and of the neural networks, capable of elaborate a series of data and territorial info, have allowed the making of a model useful in the subdivision of urban places into homogeneous zone under the profile of a social, real estate, environmental and urbanist background of a city. The development of homogeneous zone has fiscal and urbanist advantages. The tools in the model proposed, able to be adapted to the dynamic changes of the city, allow the application of the zoning fast and dynamic.
Abstract: Cooperative visual modeling is more and more
necessary in our complicated world. A collaborative environment
which supports interactive operation and communication is required
to increase work efficiency. We present a collaborative visual
modeling framework which collaborative platform could be built on.
On this platform, cooperation and communication is available for
designers from different regions. This framework, which is different
from other collaborative frameworks, contains a uniform message
format, a message handling mechanism and other functions such as
message pretreatment and Role-Communication-Token Access
Control (RCTAC). We also show our implementation of this
framework called Orchestra Designer, which support BPLE
workflow modeling cooperatively online.
Abstract: For many industrial applications plate heat
exchangers are demonstrating a large superiority over the
other types of heat exchangers. The efficiency of such a
device depends on numerous factors the effect of which needs
to be analysed and accurately evaluated.
In this paper we present a theoretical analysis of a cocurrent
plate heat exchanger and the results of its numerical
simulation.
Knowing the hot and the cold fluid streams inlet temperatures,
the respective heat capacities mCp
and the value of the
overall heat transfer coefficient, a 1-D mathematical model
based on the steady flow energy balance for a differential
length of the device is developed resulting in a set of N first
order differential equations with boundary conditions where N
is the number of channels.For specific heat exchanger
geometry and operational parameters, the problem is
numerically solved using the shooting method.
The simulation allows the prediction of the temperature
map in the heat exchanger and hence, the evaluation of its
performances. A parametric analysis is performed to evaluate
the influence of the R-parameter on the e-NTU values. For
practical purposes effectiveness-NTU graphs are elaborated
for specific heat exchanger geometry and different operating
conditions.
Abstract: Soil mechanics is a traditional course in any
university. Management of lab classes is one of the main issues to
deliver a proper outline. In Curtin University, different methods
applied to check the efficiency of these methods. One of them was
mainly rely on demonstration and the other one mainly on involving
students in running tests. Comparison between these delivery
methods also are outlined in summary section. The recommendation
also made that the more satisfaction is reachable while the students
engaged.
Abstract: The globalization of the Indian economy has thrown a great challenge to the Indian industries in respect of productivity, quality, cost, delivery etc. Achieving success• the global market has required fundamental shift in the way business is conducted and has dramatically affected virtually every aspect of process industry. The internal manufacturing process and supporting infrastructure should be such that it can compete successfully in global markets with better flexibility and delivery. The paper deals with a case study of a reputed process industry, some changes in the process has been suggested, which leads to reduction in labor cost and production cost.
Abstract: The vehicle fleet of public transportation companies is often equipped with intelligent on-board passenger information systems. A frequently used but time and labor-intensive way for keeping the on-board controllers up-to-date is the manual update using different memory cards (e.g. flash cards) or portable computers. This paper describes a compression algorithm that enables data transmission using low bandwidth wireless radio networks (e.g. GPRS) by minimizing the amount of data traffic. In typical cases it reaches a compression rate of an order of magnitude better than that of the general purpose compressors. Compressed data can be easily expanded by the low-performance controllers, too.
Abstract: Owning to the high-speed feed rate and ultra spindle
speed have been used in modern machine tools, the tool-path
generation plays a key role in the successful application of a
High-Speed Machining (HSM) system. Because of its importance in
both high-speed machining and tool-path generation, approximating a
contour by NURBS format is a potential function in CAD/CAM/CNC
systems. It is much more convenient to represent an ellipse by
parametric form than to connect points laboriously determined in a
CNC system. A new approximating method based on optimum
processes and NURBS curves of any degree to the ellipses is presented
in this study. Such operations can be the foundation of tool-radius
compensation interpolator of NURBS curves in CNC system. All
operating processes for a CAD tool is presented and demonstrated by
practical models.
Abstract: Sickle cell anemia is a recessive genetic disease
caused by the presence in the red blood cell, of abnormal hemoglobin
called hemoglobin S. It results from the replacement in the beta chain
of the acid glutamic acid by valin at position 6. Topics may be
homozygous (SS) or heterozygous (AS) most often
asymptomatic. Other mutations result in compound heterozygous:
- Synthesis of hemoglobin C mutation in the sixth leucin codon
(heterozygous SC);
- ß-thalassemia (heterozygous S-ß thalassemia).
SS homozygous, heterozygous SC and S- ß -thalassemia are grouped
under the major sickle cell syndromes.
To make a laboratory diagnosis of hemoglobinopathies in a
portion of the population in region of Batna, our study was
conducted on 115 patients with suspected sickle cell anemia, all cases
have benefited from hematological tests as blood count (count RBC,
calculated erythrocyte indices, MCV and MCHC, measuring the
hemoglobin concentration) and a biochemical test in this case
electrophoresis CAPILLARYS HEMOGLOBIN (E).
The results showed:
27 cases of sickle cell anemia were found on 115 suspected cases,
73,03% homozygous sickle cell disease and 59,25% sickle cell trait.
Finally, the double heterozygous S/C, represent the incidence rate of
3, 70%.
Abstract: When a lightning strike falls near an overhead power
line, the intense electromagnetic field radiated by the current of the
lightning return stroke coupled with power lines and there induced
transient overvoltages, which can cause a back-flashover in electrical
network. The indirect lightning represents a major danger owing to
the fact that it is more frequent than that which results from the direct
strikes.
In this paper we present an analysis of the electromagnetic
coupling between an external electromagnetic field generated by the
lightning and an electrical overhead lines, so we give an important
and original contribution: We are based on our experimental
measurements which we carried in the high voltage laboratories of
EPFL in Switzerland during the last trimester of 2005, on the recent
works of other authors and with our mathematical improvement a
new particular analytical expression of the electromagnetic field
generated by the lightning return stroke was developed and presented
in this paper. The results obtained by this new electromagnetic field
formulation were compared with experimental results and give a
reasonable approach.