Abstract: Noise has adverse effect on human health and
comfort. Noise not only cause hearing impairment, but it also acts as
a causal factor for stress and raising systolic pressure. Additionally it
can be a causal factor in work accidents, both by marking hazards
and warning signals and by impeding concentration. Industry
workers also suffer psychological and physical stress as well as
hearing loss due to industrial noise. This paper proposes an approach
to enable engineers to point out quantitatively the noisiest source for
modification, while multiple machines are operating simultaneously.
The model with the point source and spherical radiation in a free field
was adopted to formulate the problem. The procedure works very
well in ideal cases (point source and free field). However, most of the
industrial noise problems are complicated by the fact that the noise is
confined in a room. Reflections from the walls, floor, ceiling, and
equipment in a room create a reverberant sound field that alters the
sound wave characteristics from those for the free field. So the model
was validated for relatively low absorption room at NIT Kurukshetra
Central Workshop. The results of validation pointed out that the
estimated sound power of noise sources under simultaneous
conditions were on lower side, within the error limits 3.56 - 6.35 %.
Thus suggesting the use of this methodology for practical
implementation in industry. To demonstrate the application of the
above analytical procedure for estimating the sound power of noise
sources under simultaneous operating conditions, a manufacturing
facility (Railway Workshop at Yamunanagar, India) having five
sound sources (machines) on its workshop floor is considered in this
study. The findings of the case study had identified the two most
effective candidates (noise sources) for noise control in the Railway
Workshop Yamunanagar, India. The study suggests that the
modification in the design and/or replacement of these two identified
noisiest sources (machine) would be necessary so as to achieve an
effective reduction in noise levels. Further, the estimated data allows
engineers to better understand the noise situations of the workplace
and to revise the map when changes occur in noise level due to a
workplace re-layout.
Abstract: Natural gas is defined as gas obtained from a natural underground reservoir. It generally contains a large quantity of methane along with heavier hydrocarbons such as ethane, propane, isobutene, normal butane; also in the raw state it often contains a considerable amount of non hydrocarbons, such as nitrogen and the acid gases (carbon dioxide and hydrogen sulfide). The acid gases must be removed from natural gas before use. One of the processes witch are use in the industry to remove the acid gases from natural gas is the use of alkanolamine process. In this present paper, a simulation study for an industrial gas sweetening plant has been investigated. The aim of the study is to investigate the effect of using mixing amines as solvent on the gas treatment process using the software Hysys.
Abstract: The increasing industrialization and motorization of the world has led to a steep rise for the demand of petroleum-based fuels. Petroleum-based fuels are obtained from limited reserves. These finite reserves are highly concentrated in certain regions of the world. Therefore, those countries not having these resources are facing energy/foreign exchange crisis, mainly due to the import of crude petroleum. Hence, it is necessary to look for alternative fuels which can be produced from resources available locally within the country such as alcohol, biodiesel, vegetable oils etc. Biodiesel is a renewable, domestically produced fuel that has been shown to reduce particulate, hydrocarbon, and carbon monoxide emissions from combustion. In the present study an experimental investigation on emission characteristic of a liquid burner system operating on several percentage of biodiesel and gas oil is carried out. Samples of exhaust gas are analysed with Testo 350 Xl. The results show that biodiesel can lower some pollutant such as CO, CO2 and particulate matter emissions while NOx emission would increase in comparison with gas oil. The results indicate there may be benefits to using biodiesel in industrial processes.
Abstract: Activity-Based Costing (ABC) represents an
alternative paradigm to traditional cost accounting system and
it often provides more accurate cost information for decision
making such as product pricing, product mix, and make-orbuy
decisions. ABC models the causal relationships between
products and the resources used in their production and traces
the cost of products according to the activities through the use
of appropriate cost drivers. In this paper, the implementation
of the ABC in a manufacturing system is analyzed and a
comparison with the traditional cost based system in terms of
the effects on the product costs are carried out to highlight the
difference between two costing methodologies. By using this
methodology, a valuable insight into the factors that cause the
cost is provided, helping to better manage the activities of the
company.
Abstract: Brick is one of the most common masonry units used as building material. Due to the demand, different types of waste have been investigated to be incorporated into the bricks. Many types of sludge have been incorporated in fired clay brick for example marble sludge, stone sludge, water sludge, sewage sludge, and ceramic sludge. The utilization of these waste materials in fired clay bricks usually has positive effects on the properties such as lightweight bricks with improved shrinkage, porosity, and strength. This paper reviews on utilization of different types of sludge wastes into fired clay bricks. Previous investigations have demonstrated positive effects on the physical and mechanical properties as well as less impact towards the environment. Thus, the utilizations of sludge waste could produce a good quality of brick and could be one of alternative disposal methods for the sludge wastes.
Abstract: The governing two-dimensional equations of a heterogeneous material composed of a fluid (allowed to flow in the absence of acoustic excitations) and a crystalline piezoelectric cubic solid stacked one-dimensionally (along the z direction) are derived and special emphasis is given to the discussion of acoustic group velocity for the structure as a function of the wavenumber component perpendicular to the stacking direction (being the x axis). Variations in physical parameters with y are neglected assuming infinite material homogeneity along the y direction and the flow velocity is assumed to be directed along the x direction. In the first part of the paper, the governing set of differential equations are derived as well as the imposed boundary conditions. Solutions are provided using Hamilton-s equations for the wavenumber vs. frequency as a function of the number and thickness of solid layers and fluid layers in cases with and without flow (also the case of a position-dependent flow in the fluid layer is considered). In the first part of the paper, emphasis is given to the small-frequency case. Boundary conditions at the bottom and top parts of the full structure are left unspecified in the general solution but examples are provided for the case where these are subject to rigid-wall conditions (Neumann boundary conditions in the acoustic pressure). In the second part of the paper, emphasis is given to the general case of larger frequencies and wavenumber-frequency bandstructure formation. A wavenumber condition for an arbitrary set of consecutive solid and fluid layers, involving four propagating waves in each solid region, is obtained again using the monodromy matrix method. Case examples are finally discussed.
Abstract: Unified Modeling Language (UML) extensions for real time embedded systems (RTES) co-design, are taking a growing interest by a great number of industrial and research communities. The extension mechanism is provided by UML profiles for RTES. It aims at improving an easily-understood method of system design for non-experts. On the other hand, one of the key items of the co- design methods is the Hardware/Software partitioning and scheduling tasks. Indeed, it is mandatory to define where and when tasks are implemented and run. Unfortunately the main goals of co-design are not included in the usual practice of UML profiles. So, there exists a need for mapping used models to an execution platform for both schedulability test and HW/SW partitioning. In the present work, test schedulability and design space exploration are performed at an early stage. The proposed approach adopts Model Driven Engineering MDE. It starts from UML specification annotated with the recent profile for the Modeling and Analysis of Real Time Embedded systems MARTE. Following refinement strategy, transformation rules allow to find a feasible schedule that satisfies timing constraints and to define where tasks will be implemented. The overall approach is experimented for the design of a football player robot application.
Abstract: Diabetes mellitus (DM) is frequently characterized by
autonomic nervous dysfunction. Analysis of heart rate variability
(HRV) has become a popular noninvasive tool for assessing the
activities of autonomic nervous system (ANS). In this paper, changes
in ANS activity are quantified by means of frequency and time
domain analysis of R-R interval variability. Electrocardiograms
(ECG) of 16 patients suffering from DM and of 16 healthy volunteers
were recorded. Frequency domain analysis of extracted normal to
normal interval (NN interval) data indicates significant difference in
very low frequency (VLF) power, low frequency (LF) power and
high frequency (HF) power, between the DM patients and control
group. Time domain measures, standard deviation of NN interval
(SDNN), root mean square of successive NN interval differences
(RMSSD), successive NN intervals differing more than 50 ms (NN50
Count), percentage value of NN50 count (pNN50), HRV triangular
index and triangular interpolation of NN intervals (TINN) also show
significant difference between the DM patients and control group.
Abstract: A kinetic model for propane dehydrogenation in an
industrial moving bed reactor is developed based on the reported
reaction scheme. The kinetic parameters and activity constant are
fine tuned with several sets of balanced plant data. Plant data at
different operating conditions is applied to validate the model and
the results show a good agreement between the model
predictions and plant observations in terms of the amount of main
product, propylene produced. The simulation analysis of key
variables such as inlet temperature of each reactor (Tinrx) and
hydrogen to total hydrocarbon ratio (H2/THC) affecting process
performance is performed to identify the operating condition to
maximize the production of propylene. Within the range of operating
conditions applied in the present studies, the operating condition to
maximize the propylene production at the same weighted average
inlet temperature (WAIT) is ΔTinrx1= -2, ΔTinrx2= +1, ΔTinrx3= +1 ,
ΔTinrx4= +2 and ΔH2/THC= -0.02. Under this condition, the surplus
propylene produced is 7.07 tons/day as compared with base case.
Abstract: A series of experiments were carried out to study
unsteady behavior of the flow field as well as the boundary layer of
an airfoil oscillating in plunging motion in a subsonic wind tunnel.
The measurements involved surface pressure distribution
complimented with surface-mounted hot-films. The effect of leadingedge
roughness that simulates surface irregularities on the wind
turbine blades was also studied on variations of aerodynamic loads
and boundary layer behavior.
Abstract: Insufficient Quality of Service (QoS) of Voice over
Internet Protocol (VoIP) is a growing concern that has lead the need
for research and study. In this paper we investigate the performance
of VoIP and the impact of resource limitations on the performance of
Access Networks. The impact of VoIP performance in Access
Networks is particularly important in regions where Internet
resources are limited and the cost of improving these resources is
prohibitive. It is clear that perceived VoIP performance, as measured
by mean opinion score [2] in experiments, where subjects are asked
to rate communication quality, is determined by end-to-end delay on
the communication path, delay variation, packet loss, echo, the
coding algorithm in use and noise. These performance indicators can
be measured and the affect in the Access Network can be estimated.
This paper investigates the congestion in the Access Network to the
overall performance of VoIP services with the presence of other
substantial uses of internet and ways in which Access Networks can
be designed to improve VoIP performance. Methods for analyzing
the impact of the Access Network on VoIP performance will be
surveyed and reviewed. This paper also considers some approaches
for improving performance of VoIP by carrying out experiments
using Network Simulator version 2 (NS2) software with a view to
gaining a better understanding of the design of Access Networks.
Abstract: Protein 3D structure prediction has always been an
important research area in bioinformatics. In particular, the
prediction of secondary structure has been a well-studied research
topic. Despite the recent breakthrough of combining multiple
sequence alignment information and artificial intelligence algorithms
to predict protein secondary structure, the Q3 accuracy of various
computational prediction algorithms rarely has exceeded 75%. In a
previous paper [1], this research team presented a rule-based method
called RT-RICO (Relaxed Threshold Rule Induction from Coverings)
to predict protein secondary structure. The average Q3 accuracy on
the sample datasets using RT-RICO was 80.3%, an improvement
over comparable computational methods. Although this demonstrated
that RT-RICO might be a promising approach for predicting
secondary structure, the algorithm-s computational complexity and
program running time limited its use. Herein a parallelized
implementation of a slightly modified RT-RICO approach is
presented. This new version of the algorithm facilitated the testing of
a much larger dataset of 396 protein domains [2]. Parallelized RTRICO
achieved a Q3 score of 74.6%, which is higher than the
consensus prediction accuracy of 72.9% that was achieved for the
same test dataset by a combination of four secondary structure
prediction methods [2].
Abstract: Current spectrums of a high power induction machine was calculated for the cases of full symmetry, static and dynamic eccentricity. The calculations involve integration of 93 electrical plus four mechanical ordinary differential equations. Electrical equations account for variable inductances affected by slotting and eccentricities. The calculations were followed by Fourier analysis of the stator currents in steady state operation. The paper presents the stator current spectrums in full symmetry, static and dynamic eccentricity cases, and demonstrates the harmonics present in each case. The effect of dynamic eccentricity is demonstrating via comparing the current spectrums related to dynamic eccentricity cases with the full symmetry one. The paper includes one case study, refers to dynamic eccentricity, to present the spectrum of the measured current and demonstrate the existence of the harmonics related to dynamic eccentricity. The zooms of current spectrums around the main slot harmonic zone are included to simplify the comparison and prove the existence of the dynamic eccentricity harmonics in both calculated and measured current spectrums.
Abstract: The use of a Bayesian Hierarchical Model (BHM) to interpret breath measurements obtained during a 13C Octanoic Breath Test (13COBT) is demonstrated. The statistical analysis was implemented using WinBUGS, a commercially available computer package for Bayesian inference. A hierarchical setting was adopted where poorly defined parameters associated with a delayed Gastric Emptying (GE) were able to "borrow" strength from global distributions. This is proved to be a sufficient tool to correct model's failures and data inconsistencies apparent in conventional analyses employing a Non-linear least squares technique (NLS). Direct comparison of two parameters describing gastric emptying ng ( tlag -lag phase, t1/ 2 -half emptying time) revealed a strong correlation between the two methods. Despite our large dataset ( n = 164 ), Bayesian modeling was fast and provided a successful fitting for all subjects. On the contrary, NLS failed to return acceptable estimates in cases where GE was delayed.
Abstract: This paper describes a one-dimensional numerical model for natural gas production from the dissociation of methane hydrate in hydrate-capped gas reservoir under depressurization and thermal stimulation. Some of the hydrate reservoirs discovered are overlying a free-gas layer, known as hydrate-capped gas reservoirs. These reservoirs are thought to be easiest and probably the first type of hydrate reservoirs to be produced. The mathematical equations that can be described this type of reservoir include mass balance, heat balance and kinetics of hydrate decomposition. These non-linear partial differential equations are solved using finite-difference fully implicit scheme. In the model, the effect of convection and conduction heat transfer, variation change of formation porosity, the effect of using different equations of state such as PR and ER and steam or hot water injection are considered. In addition distributions of pressure, temperature, saturation of gas, hydrate and water in the reservoir are evaluated. It is shown that the gas production rate is a sensitive function of well pressure.
Abstract: The objective of this research is to study plant layout
of iron manufacturing based on the systematic layout planning
pattern theory (SLP) for increased productivity. In this case study,
amount of equipments and tools in iron production are studied. The
detailed study of the plant layout such as operation process chart,
flow of material and activity relationship chart has been investigated.
The new plant layout has been designed and compared with the
present plant layout. The SLP method showed that new plant layout
significantly decrease the distance of material flow from billet
cutting process until keeping in ware house.
Abstract: Studies regarding the determination of population
trend of Lipaphis erysimi (kalt.) and its associated natural enemies in
different Brassica lines along with the effect of gamma radiation on
their population were conducted at Agricultural Research Farm,
Malakandher, Khyber Pakhtunkhwa Agricultural University
Peshawar during spring 2006. Three different Brassica lines F6B3,
F6B6 and F6B7 were used, which were replicated four times in
Randomized Complete Block Design. The data revealed that aphid
infestation invariably stated in all three varieties during last week of
February 2006 (1st observation). The peak population of 4.39 aphids
leaf-1 was s recorded during 2nd week of March and lowest population
of 1.02 aphids leaf-1 was recorded during 5th week of March. The
species of lady bird beetle (Coccinella septempunctata) and Syrphid
fly (Syrphus balteatus) first appeared on 24th February with a mean
number of 0.40 lady bird beetle leaf-1 and 0.87 Syrphid fly leaf-1,
respectively. At the time when aphid population started to increase
the peak population of C. septempunctata (0.70 lady bird beetle leaf-
1) and S. balteatus (1.04 syrphid fly leaf-1) was recorded on the 2nd
week of March. Chrysoperla carnea appeared in the 1st week of
March and their peak population was recorded during the 3rd week of
March with mean population of 1.46 C. carnea leaf-1. Among all the
Brassica lines, F6B7 showed comparatively more resistance as
compared to F6B3 F6B6. F6B3 showed least resistance against L.
erysimi, which was found to be the most susceptible cultivar. F6B7
was also found superior in terms of natural enemies. Maximum
number of all natural enemies was recorded on this variety followed
by F6B6. Lowest number of natural enemies was recorded in F6B3.
No significant effect was recorded for the effect of gamma radiation
on the population of aphids, natural enemies and on the varieties.
Abstract: This study considers priorities of primary goals to increase policy efficiency of Green ICT. Recently several studies have been published that address how IT is linked to climate change. However, most of the previous studies are limited to Green ICT industrial statute and policy directions. This paper present Green ICT
policy making processes systematically. As a result of the analysis of
Korean Green ICT policy, the following emerged as important to accomplish for Green ICT policy: eco-friendliness, technology evolution, economic efficiency, energy efficiency, and stable supply
of energy. This is an initial study analyzing Green ICT policy, which provides an academic framework that can be used a guideline to
establish Green ICT policy.
Abstract: In this paper a novel structure of metamaterial is
proposed in order to miniaturize a rectangular microstrip patch
antenna. The metamaterial is composed of two nested split octagons
which are located on a 10 mm
Abstract: The research objective aims to search information about storytelling and fable associated with fireflies in Amphawa community, in order to design and create a story book which is appropriate for the interests of children in early childhood. This book should help building the development of learning about the natural environment, imagination, and creativity among children, which then, brings about the promotion of the development, conservation and dissemination of cultural values and uniqueness of the Amphawa community. The population used in this study were 30 students in early childhood aged between 6-8 years-old, grade 1-3 from the Demonstration School of Suan Sunandha Rajabhat University. The method used for this study was purposive sampling and the research conducted by the query and analysis of data from both the document and the narrative field tales and fable associated with the fireflies of Amphawa community. Then, using the results to synthesize and create a conceptual design in a form of 8 visual images which were later applied to 1 illustrated children’s book and presented to the experts to evaluate and test this media.