Abstract: This article experimentally investigates the
thermal performance of thermoelectric air-cooling module
which comprises a thermoelectric cooler (TEC) and an
air-cooling heat sink. The influences of input current and heat
load are determined. And performances under each situation
are quantified by thermal resistance analysis. Since TEC
generates Joule heat, this nature makes construction of thermal
resistance network difficult. To simplify the analysis, this
article emphasizes on the resistance heat load might meet when
passing through the device. Therefore, the thermal resistances
in this paper are to divide temperature differences by heat load.
According to the result, there exists an optimum input current
under every heating power. In this case, the optimum input
current is around 6A or 7A. The performance of the heat sink
would be improved with TEC under certain heating power and
input current, especially at a low heat load. According to the
result, the device can even make the heat source cooler than the
ambient. However, TEC is not always effective at every heat
load and input current. In some situation, the device works
worse than the heat sink without TEC. To determine the
availability of TEC, this study figures out the effective
operating region in which the TEC air-cooling module works
better than the heat sink without TEC. The result shows that
TEC is more effective at a lower heat load. If heat load is too
high, heat sink with TEC will perform worse than without TEC.
The limit of this device is 57W. Besides, TEC is not helpful if
input current is too high or too low. There is an effective range
of input current, and the range becomes narrower when the heat
load grows.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: The aim of this study is evaluating the antinociceptive
and anti-inflamatory activity of Geum kokanicum. After
determination total extract LD50, different doses of extract were
chosen for intrapritoneal injections. In inflammation test, male NMRI
mice were divided into 6 groups: control (normal saline), positive
control (Dexamethasone 15mg/kg), and total extract (0.025, 0.05,
0.1, and 0.2 gr/kg). The inflammation was produced by xyleneinduced
edema. In order to evaluate the antinociceptive effect of total
extract, formalin test was used. Mice were divided into 6 groups:
control, positive control (morphine 10mg/kg), and 4 groups which
received total extract. Then they received Formalin. The animals
were observed for the reaction to pain. Data were analyzed using
One-way ANOVA followed by Tukey-Kramer multiple comparison
test. LD50 was 1 gr/kg. Data indicated that 0.5,0.1 and 0.2 gr/kg
doses of total extract have particular antinociceptive and antiinflammatory
effects in a comparison with control (P
Abstract: Magnesium is used implant material potentially for
non-toxicity to the human body. Due to the excellent
bio-compatibility, Mg alloys is applied to implants avoiding removal
second surgery. However, it is found commercial magnesium alloys
including aluminum has low corrosion resistance, resulting
subcutaneous gas bubbles and consequently the approach as
permanent bio-materials. Generally, Aluminum is known to pollution
substance, and it raises toxicity to nervous system. Therefore
especially Mg-35Zn-3Ca alloy is prepared for new biodegradable
materials in this study. And the pulsed power is used in
constant-current mode of DC power kinds of anodization. Based on
the aforementioned study, it examines corrosion resistance and
biocompatibility by effect of current and frequency variation. The
surface properties and thickness were compared using scanning
electronic microscopy. Corrosion resistance was assessed via
potentiodynamic polarization and the effect of oxide layer on the body
was assessed cell viability. Anodized Mg-35Zn-3Ca alloy has good
biocompatibility in vitro by current and frequency variation.
Abstract: The study of the transport coefficients in electronic
devices is currently carried out by analytical and empirical models.
This study requires several simplifying assumptions, generally
necessary to lead to analytical expressions in order to study the
different characteristics of the electronic silicon-based devices.
Further progress in the development, design and optimization of
Silicon-based devices necessarily requires new theory and modeling
tools. In our study, we use the PSO (Particle Swarm Optimization)
technique as a computational tool to develop analytical approaches in
order to study the transport phenomenon of the electron in crystalline
silicon as function of temperature and doping concentration. Good
agreement between our results and measured data has been found.
The optimized analytical models can also be incorporated into the
circuits simulators to study Si-based devices without impact on the
computational time and data storage.
Abstract: The purpose of this study was to study postpartum breastfeeding mothers to determine the impact their psychosocial and spiritual dimensions play in promoting full-term (6 month duration) breastfeeding of their infants. Purposive and snowball sampling methods were used to identify and recruit the study's participants. A total of 23 postpartum mothers, who were breastfeeding within 6 weeks after giving birth, participated in this study. In-depth interviews combined with observations, participant focus groups, and ethnographic records were used for data collection. The Data were then analyzed using content analysis and typology. The results of this study illustrated that postpartum mothers experienced fear and worry that they would lack support from their spouse, family and peers, and that their infant would not get enough milk It was found that the main barrier mothers faced in breastfeeding to full-term was the difficulty of continuing to breastfeed when returning to work. 81.82% of the primiparous mothers and 91.67% of the non-primiparous mothers were able to breastfeed for the desired full-term of 6 months. Factors found to be related to breastfeeding for six months included 1) belief and faith in breastfeeding, 2) support from spouse and family members, 3) counseling from public health nurses and friends. The sample also provided evidence that religious principles such as tolerance, effort, love, and compassion to their infant, and positive thinking, were used in solving their physical, mental and spiritual problems.
Abstract: This paper presents an interval-based multi-attribute
decision making (MADM) approach in support of the decision
process with imprecise information. The proposed decision
methodology is based on the model of linear additive utility function
but extends the problem formulation with the measure of composite
utility variance. A sample study concerning with the evaluation of
electric generation expansion strategies is provided showing how the
imprecise data may affect the choice toward the best solution and
how a set of alternatives, acceptable to the decision maker (DM),
may be identified with certain confidence.
Abstract: This paper presents the experimental results of a
single cylinder Enfield engine using an electronically controlled fuel
injection system which was developed to carry out exhaustive tests
using neat CNG, and mixtures of hydrogen in compressed natural gas
(HCNG) as 0, 5, 10, 15 and 20% by energy. Experiments were
performed at 2000 and 2400 rpm with wide open throttle and varying
the equivalence ratio. Hydrogen which has fast burning rate, when
added to compressed natural gas, enhances its flame propagation rate.
The emissions of HC, CO, decreased with increasing percentage of
hydrogen but NOx was found to increase. The results indicated a
marked improvement in the brake thermal efficiency with the
increase in percentage of hydrogen added. The improved thermal
efficiency was clearly observed to be more in lean region as
compared to rich region. This study is expected to reduce vehicular
emissions along with increase in thermal efficiency and thus help in
reduction of further environmental degradation.
Abstract: This paper describes the results and implications of a correlational study of learning styles and learner satisfaction. The relationship of these empirical concepts was examined in the context of traditional versus e-blended modes of course delivery in an introductory graduate research course. Significant results indicated that the visual side of the visual-verbal dimension of students- learning style(s) was positively correlated to satisfaction with themselves as learners in an e-blended course delivery mode and negatively correlated to satisfaction with the classroom environment in the context of a traditional classroom course delivery mode.
Abstract: Logistics outsourcing is a growing trend and measuring its performance, a challenge. It must be consistent with the objectives set for logistics outsourcing, but we have found no objective-based performance measurement system. We have conducted a comprehensive review of the specialist literature to cover this gap, which has led us to identify and define these objectives. The outcome is that we have obtained a list of the most relevant objectives and their descriptions. This will enable us to analyse in a future study whether the indicators used for measuring logistics outsourcing performance are consistent with the objectives pursued with the outsourcing. If this is not the case, a proposal will be made for a set of financial and operational indicators to measure performance in logistics outsourcing that take the goals being pursued into account.
Abstract: This paper demonstrates the results when either
Shiftrows stage or Mixcolumns stage and when both the stages are
omitted in the well known block cipher Advanced Encryption
Standard(AES) and its modified version AES with Key Dependent
S-box(AES-KDS), using avalanche criterion and other tests namely
encryption quality, correlation coefficient, histogram analysis and
key sensitivity tests.
Abstract: Software effort estimation is the process of predicting
the most realistic use of effort required to develop or maintain
software based on incomplete, uncertain and/or noisy input. Effort
estimates may be used as input to project plans, iteration plans,
budgets. There are various models like Halstead, Walston-Felix,
Bailey-Basili, Doty and GA Based models which have already used
to estimate the software effort for projects. In this study Statistical
Models, Fuzzy-GA and Neuro-Fuzzy (NF) Inference Systems are
experimented to estimate the software effort for projects. The
performances of the developed models were tested on NASA
software project datasets and results are compared with the Halstead,
Walston-Felix, Bailey-Basili, Doty and Genetic Algorithm Based
models mentioned in the literature. The result shows that the NF
Model has the lowest MMRE and RMSE values. The NF Model
shows the best results as compared with the Fuzzy-GA based hybrid
Inference System and other existing Models that are being used for
the Effort Prediction with lowest MMRE and RMSE values.
Abstract: The objective of this study was to improve our
understanding of vulnerability and environmental change; it's causes
basically show the intensity, its distribution and human-environment
effect on the ecosystem in the Apodi Valley Region, This paper is
identify, assess and classify vulnerability and environmental change
in the Apodi valley region using a combined approach of landscape
pattern and ecosystem sensitivity. Models were developed using the
following five thematic layers: Geology, geomorphology, soil,
vegetation and land use/cover, by means of a Geographical
Information Systems (GIS)-based on hydro-geophysical parameters.
In spite of the data problems and shortcomings, using ESRI-s ArcGIS
9.3 program, the vulnerability score, to classify, weight and combine
a number of 15 separate land cover classes to create a single indicator
provides a reliable measure of differences (6 classes) among regions
and communities that are exposed to similar ranges of hazards.
Indeed, the ongoing and active development of vulnerability
concepts and methods have already produced some tools to help
overcome common issues, such as acting in a context of high
uncertainties, taking into account the dynamics and spatial scale of
asocial-ecological system, or gathering viewpoints from different
sciences to combine human and impact-based approaches. Based on
this assessment, this paper proposes concrete perspectives and
possibilities to benefit from existing commonalities in the
construction and application of assessment tools.
Abstract: Indoor air distribution has great impact on people-s thermal sensation. Therefore, how to remove the indoor excess heat becomes an important issue to create a thermally comfortable indoor environment. To expel the extra indoor heat effectively, this paper used a dynamic CFD approach to study the effect of an air-supply guide vane swinging periodically on the indoor air distribution within a model room. The numerical results revealed that the indoor heat transfer performance caused by the swing guide vane had close relation with the number of vortices developing under the inlet cold jet. At larger swing amplitude, two smaller vortices continued to shed outward under the cold jet and remove the indoor heat load more effectively. As a result, it can be found that the average Nusselt number on the floor increased with the increase of the swing amplitude of the guide vane.
Abstract: In this work, ionic liquids (ILs) for CO2 capturing in typical absorption/stripper process are considered. The use of ionic liquids is considered to be cost-effective because it requires less energy for solvent recovery compared to other conventional processes. A mathematical model is developed for the process based on Peng-Robinson (PR) equation of state (EoS) which is validated with experimental data for various solutions involving CO2. The model is utilized to study the sorbent and energy demand for three types of ILs at specific CO2 capturing rates. The energy demand is manifested by the vapor-liquid equilibrium temperature necessary to remove the captured CO2 from the used solvent in the regeneration step. It is found that higher recovery temperature is required for solvents with higher solubility coefficient. For all ILs, the temperature requirement is less than that required by the typical monoethanolamine (MEA) solvent. The effect of the CO2 loading in the sorbent stream on the process performance is also examined.
Abstract: The investigating and assessing the effects of
relaxation training on the levels of state anxiety concerning first year
female nursing students at their initial experience in clinical setting.
This research is a quasi experimental study that was carried out in
nursing and midwifery faculty of Tehran university of medical
sciences .The sample of research consists 60 first term female
nursing students were selected through convenience and random
sampling. 30 of them were the experimental group and 30 of them
were in control group. The Instruments of data-collection has been a
questionnaire which consists of 3 parts. The first part includes 10
questions about demographic characteristics .the second part includes
20 question about anxiety (test 'Spielberg' ). The 3rd part includes
physiological indicators of anxiety (BP, P, R, body temperature). The
statistical tests included t-test and and fisher test, Data were
analyzed by SPSS software.
Abstract: Music has a great effect on human body and mind; it
can have a positive effect on hormone system. Objective of this study
is to analysis the effect of music (carnatic, hard rock and jazz) on
brain activity during mental work load using electroencephalography
(EEG). Eight healthy subjects without special musical education
participated in the study. EEG signals were acquired at frontal (Fz),
parietal (Pz) and central (Cz) lobes of brain while listening to music
at three experimental condition (rest, music without mental task and
music with mental task). Spectral powers features were extracted at
alpha, theta and beta brain rhythms. While listening to jazz music, the
alpha and theta powers were significantly (p < 0.05) high for rest as
compared to music with and without mental task in Cz. While
listening to Carnatic music, the beta power was significantly (p <
0.05) high for with mental task as compared to rest and music
without mental task at Cz and Fz location. This finding corroborates
that attention based activities are enhanced while listening to jazz and
carnatic as compare to Hard rock during mental task.
Abstract: The study was carried out to evaluated effect of S-gridling on fruit growth and quality of wax apple. The study was laid in Random completed block design with four replicated. Four treatment were applied as follows: S-girdling, fruit thinning plus bagging with 2,4-D sprayed, fruit thinning plus bagging and the control treatment. 2,4D was sprayed at the small bud and petal fall stage. Girdling was applied three week before flowering. The effect of all treatments on fruit growth was measured weekly. Number of flower, fruit set, fruit drop, fruit crack, and fruit quality were recorded. The result indicated that S-girdling, 2,4D application produced the lowest bud drop, fruit drop compared to untreated control. S-girdling improved faster fruit growth producing the best final fruit length and diameter compared to untreated control. S-girdling also markedly enhanced fruit set, fruit weight, and total soluble solid, reduced fruit crack, titratable acidity. On the other hand, it was noticed that with 2,4-D application also increased the fruit growth rate, improved physiological and biochemical characters of fruit than control treatment. It was concluded that S-girdling was recommended as the industry norm to increase fruit set, fruit quality in wax apple. 2,4D application had a distinctive and significant effect on most of the fruit quality characteristics assessed.
Abstract: This paper addresses one important aspect of
combustion system analysis, the spray evaporation and
dispersion modeling. In this study we assume an empty
cylinder which is as a simulator for a ramjet engine and the
cylinder has been studied by cold flow. Four nozzles have the
duties of injection which are located in the entrance of
cylinder. The air flow comes into the cylinder from one side
and injection operation will be done. By changing injection
velocity and entrance air flow velocity, we have studied
droplet sizing and efficient mass fraction of fuel vapor near
and at the exit area. We named the mass of fuel vapor inside
the flammability limit as the efficient mass fraction. Further,
we decreased the initial temperature of fuel droplets and we
have repeated the investigating again. To fulfill the calculation
we used a modified version of KIVA-3V.
Abstract: Academic research information service is a must for surveying previous studies in research and development process. OntoFrame is an academic research information service under Semantic Web framework different from simple keyword-based services such as CiteSeer and Google Scholar. The first purpose of this study is for revealing user behavior in their surveys, the objects of using academic research information services, and their needs. The second is for applying lessons learned from the results to OntoFrame.