Abstract: Different approaches for heating\cooling of stirred tanks, coils and jackets, are investigated using computational fluid dynamics (CFD).A time-dependant sliding mesh approach is applied to simulate the flow in both conditions. The investigations are carried out under the turbulent flow conditions for a Rushton impeller and heating elements are considered isothermal. The flow behavior and temperature distribution are studied for each case and heat transfer coefficient is calculated. Results show different velocity profiles for each case. Unsteady temperature distribution is not similar for different cases .In the case of the coiled stirred vessel more uniform temperature and higher heat transfer coefficient is resulted.
Abstract: The objective of this project is to study the corrosion
behaviour and hardness based on the presence of martensite in dual
phase steel. This study was conducted on six samples of dual phase
steel which have different percentage of martensite. A total of 9
specimens were prepared by intercritical annealing process to study
the effect of temperature to the formation of martensite. The low
carbon steels specimens were heated for 25 minutes in a specified
temperature ranging from 7250C to 8250C followed by rapid cooling
in water. The measurement of corrosion rate was done by using
extrapolation tafel method, while potentiostat was used to control and
measured the current produced. This measurement is performed
through a system named CMS105. The result shows that a specimen
with higher percentage of martensite is likely to corrode faster.
Hardness test for each specimen was conducted to compare its
hardness with low carbon steel. The results obtained indicate that the
specimen hardness is proportional to the amount of martensite in dual
phase steel.
Abstract: Research on the boron (B) toxicity problems had recently considerable relation, especially in the dry regions of the world. Development of resistant varieties to B toxicity is a high priority on these regions, where the soils have high levels of B. Thus, this study aimed to assessment the resistance of wheat genotypes to B toxicity using the agronomic and physiologic parameters. For this aim, a pot experiment, based on a completely randomized design with three replications, was conducted using the soil of calcareous usthochrepts. In the study, twenty different wheat genotypes of T. aestivum and T. Durum were used. Boron fertilizer at the levels of 0 (-B), 30 mg B kg-1 (+B) as H3BO3 was applied to the pots. After harvest, plant dry matter yield was recorded, and total B concentrations in tops of wheat plants were determined. The results have revealed the existence of a large genotypic variation among wheat genotypes to their physiologic and agronomic susceptibility to B toxicity.
Abstract: Experimental investigation of heat transfer and
friction factor characteristics of circular tube fitted with 300 right-left helical screw inserts with 100 mm spacer of different twist ratio has
been presented for laminar and turbulent flow.. The experimental data obtained were compared with those obtained from plain tube
published data. The heat transfer coefficient enhancement for 300 RL
inserts with 100 mm spacer is quite comparable with for 300 R-L
inserts. Performance evaluation analysis has been made and found
that the performance ratio increases with increasing Reynolds number
and decreasing twist ration with the maximum for the twist ratio 2.93.
Also, the performance ratio of more than one indicates that the type
of twist inserts can be used effectively for heat transfer augmentation.
Abstract: Calcium oxide (CaO) as carbon dioxide (CO2)
adsorbent at the elevated temperature has been very well-received
thus far. The CaO can be synthesized from natural calcium carbonate
(CaCO3) sources through the reversible calcination-carbonation
process. In the study, cockle shell has been selected as CaO
precursors. The objectives of the study are to investigate the
performance of calcination and carbonation with respect to different
temperature, heating rate, particle size and the duration time. Overall,
better performance is shown at the calcination temperature of 850oC
for 40 minutes, heating rate of 20oC/min, particle size of < 0.125mm
and the carbonation temperature is at 650oC. The synthesized
materials have been characterized by nitrogen physisorption and
surface morphology analysis. The effectiveness of the synthesized
cockle shell in capturing CO2 (0.72 kg CO2/kg adsorbent) which is
comparable to the commercialized adsorbent (0.60 kg CO2/kg
adsorbent) makes them as the most promising materials for CO2
capture.
Abstract: The equilibrium process of plasma nitrogen species by
chemical kinetic reactions along various pressures is successfully
investigated. The equilibrium process is required in industrial
application to obtain the stable condition when heating up the
material for having homogenous reaction. Nitrogen species densities
is modeled by a continuity equation and extended Arrhenius form.
These equations are used to integrate the change of density over the
time. The integration is to acquire density and the reaction rate of
each reaction where temperature and time dependence are imposed.
A comparison is made with global model within pressure range of 1-
100mTorr and the temperature of electron is set to be higher than
other nitrogen species. The results shows that the chemical kinetic
model only agrees for high pressure because of no power imposed;
while the global model considers the external power along the
pressure range then the electron and nitrogen species give highly
quantity densities by factor of 3 to 5.
Abstract: In all industries which are related to heat, suitable
thermal ranges are defined for each device to operate well.
Consideration of these limits requires a thermal control unit beside
the main system. The Satellite Thermal Control Unit exploits from
different methods and facilities individually or mixed. For enhancing
heat transfer between primary surface and the environment,
utilization of radiating extended surfaces are common. Especially for
large temperature differences; variable thermal conductivity has a
strong effect on performance of such a surface .In most literatures,
thermo-physical properties, such as thermal conductivity, are
assumed as constant. However, in some recent researches the
variation of these parameters is considered. This may be helpful for
the evaluation of fin-s temperature distribution in relatively large
temperature differences. A new method is introduced to evaluate
temperature-dependent thermal conductivity values. The finite
volume method is employed to simulate numerically the temperature
distribution in a space radiating fin. The present modeling is carried
out for Aluminum as fin material and compared with previous
method. The present results are also compared with those of two
other analytical methods and good agreement is shown.
Abstract: This paper is concerned with calculating boiler
efficiency as one of the most important types of performance
measurements in any steam power plant. That has a key role in
determining the overall effectiveness of the whole system within the
power station. For this calculation, a Visual-Basic program was
developed, and a steam power plant known as El-Khmus power
plant, Libya was selected as a case study. The calculation of the
boiler efficiency was applied by using heating balance method. The
findings showed how the maximum heat energy which produced
from the boiler increases the boiler efficiency through increasing the
temperature of the feed water, and decreasing the exhaust
temperature along with humidity levels of the of fuel used within the
boiler.
Abstract: A numerical study has been conducted to investigate the influence of fin pitch and relative humidity on the heat transfer performance of the fin-and-tube heat exchangers having plain fin geometry under dehumidifying conditions. The analysis is done using the ratio between the heat transfer coefficients in totally wet conditions and those in totally dry conditions using the appropriate correlations for both dry and wet conditions. For a constant relative humidity, it is found that the heat transfer coefficient increases with the increase of the air frontal velocity. By contrast, the fin efficiency decreases when the face velocity is increased. Apparently, this phenomenon is attributed to the path of condensate drainage. For the influence of relative humidity, the results showed an increase in heat transfer performance and a decrease in wet fin efficiency when relative humidity increases. This is due to the higher amount of mass transfer encountered at higher relative humidity. However, it is found that the effect of fin pitch on the heat transfer performance depends strongly on the face velocity. At lower frontal velocity the heat transfer increases with fin pitch. Conversely, an increase in fin pitch gives lower heat transfer coefficients when air velocity is increased.
Abstract: Paleoclimate was reconstructed by the clay mineral
assemblages of shale units of Pabdeh (Paleocene- Oligocene), Gurpi
(Upper Cretaceous), Kazhdumi (Albian-Cenomanian) and Gadvan
(Aptian-Neocomian) formations in the Bangestan anticline. To
compare with clay minerals assemblages in these formations,
selected samples also taken from available formations in drilled wells
in Ahvaz, Marun, Karanj, and Parsi oil fields. Collected samples
prepared using standard clay mineral methodology. They were
treated as normal, glycolated and heated oriented glass slides. Their
identification was made on X-Ray diffractographs. Illite % varies
from 8 to 36. Illite quantity increased from Pabdeh to Gurpi
Formation. This may be due to dominant dry climate. Kaolinite is in
range of 12-49%. Its variation style in different formations could be a
marker of climate changes from wet to dry which is supported by the
lithological changes. Chlorite (4-28%) can also be detected in those
samples without any kaolinite. Mixed layer minerals as the mixture
of illite-chlorite and illite-vermiculite-montmorillonite are varied
from 6 to 36%, decreased during Kazhdumi deposition from the base
to the top. This result may be according to decreasing of illite
leaching process. Vermiculite was also determined in very less
quantity and found in those units without kaolinite. Montmorillonite
varies from 8 to 43%, and its presence is due to terrestrial
depositional condition. Stratigraphical documents is also supported
this idea that clay mineral distribution is a function of the climate
changes. It seems, thus, the present results can be indicated a possible
procedure for ancient climate changes evaluation.
Abstract: In space during functioning, a satellite will be heated
up due to the behavior of its components such as power electronics.
In order to prevent problems in the satellite, this heat has to be
released in space thanks to the cooling system. This system consists
of a loop heat pipe (LHP), in which a fluid streams through an
evaporator and a condenser. In the evaporator, the fluid captures the
heat from the satellite and evaporates. Then it flows to the condenser
where it releases the heat and it condenses. In this project, the two
mains parts of a cooling system are studied: the evaporator and the
condenser. The study of the diphasic loop was done starting from
digital simulations carried out under Matlab and Femlab.
Abstract: Tufting carpet is a very suitable substrate for growing
microorganism such as pathogenic microbes, due to the direct touch
with human body, long washing periods and laying on the floor; in
fact there are 3 major problems: To risk human health, Prepare bad
odors and Destruction of the products.. In the presented research, for
investigation of presence most common microbes on polyester
tufting, first goods laid in a public place (in the corridor fair) for 30
days and the existence of some microbes were investigate on it with
two methods of enrichment in nutrient environments such as
thioglycolate and noutrunt brath, and shake the dust off the polyester
tufting onto cultivation mediums such as blood agar and noutrunt
agar. After the microorganism colonics are grown, the colonies were
separated and six microbial tests such as cataloes and sitrat were
carried out in five phases on the colonics for identifying the varieties
of bacteria. As a result of tests, 5 type of bacteria, such as
Escherichia coli, staphylococcus saprophytic as were identified. Each
of the mentioned bacteria can be seriously harmful for the heath of
human.
Abstract: This paper investigates the effects of lubrication on
the quantity of heat emission of two spur gear. System with and
without lubrication effected on the quantity of heat induced on the
gear box (oil - bearings – gears). Both of lubrication and speed of
motor are affected on the performance of gears. Research investigated
the lubrication on the system with and without loading as well as the
wear of gears and bearing's conditions. Gear box investigated
includes the motor, pump, two spur gears, two shafts; speed change
used pulleys and belts. Load used equal one weight ones of gear.
Lubrication mechanism used jet system (upper and lower jet). Gear
box we used system of jet lubrication is perpendicular direction of
the contact line between two teeth. Results appeared in this work that
the lubrication is the vital parameter which is affected on the
performance and durability of gears and bearings. In macroscopic
observation, we noted that damage of bearings happened during the
absence of lubrication as well as abrasive of wear of teeth. Higher
speed of motor without lubrication increased the noise, but in the
presence of lubrication was decreased.
Abstract: The current paper presents a numerical approach in solving the conjugate heat transfer problems. A heat conduction code is coupled internally with a computational fluid dynamics solver for developing a couple conjugate heat transfer solver. Methodology of treating non-matching meshes at interface has also been proposed. The validation results of 1D and 2D cases for the developed conjugate heat transfer code have shown close agreement with the solutions given by analysis.
Abstract: Researches on the general rules of temperature field
changing and their effects on the bridge in construction are necessary.
This paper investigated the rules of temperature field changing and its
effects on bridge using onsite measurement and computational
analysis. Guanyinsha Bridge was used as a case study in this research.
The temperature field was simulated in analyses. The effects of certain
boundary conditions such as sun radiance, wind speed, and model
parameters such as heat factor and specific heat on temperature field
are investigated. Recommended values for these parameters are
proposed. The simulated temperature field matches the measured
observations with high accuracy. At the same time, the stresses and
deflections of the bridge computed with the simulated temperature
field matches measured values too. As a conclusion, the temperature
effect analysis of reinforced concrete box girder can be conducted
directly based on the reliable weather data of the concerned area.
Abstract: Celiac disease is an immune-mediated disease, triggered in genetically susceptible individuals by ingested gluten from wheat, rye, barley and other closely related cereal grains. The only effective treatment is a strict gluten free diet for life. Latvian producers do not offer gluten-free products. In this research, use of extruded maize flour was tested for substituting rice, maize or buckwheat flour in gluten-free bread formulations at different ratios. Also the influence of extruded maize flour on the quality parameters of gluten-free bread was investigated. The aim of research was to study the influence of extruded maize flour on gluten-free bread quality. Addition of extruded maize flour affect gluten-free bread crumb color, structure of crumb, weight loss and dry off of bread.
Abstract: The objective of this experiment was to study of water
relations and chlorophyll in different wheat genotypes and their
correlations with grain and biological yields. 21 genotypes of bread
wheat were compared in a field experiment as randomized complete
blocks design with four replications. The results showed that relative
water deficit, relative water loss, excised leaf water retention, cell
membrane stability, chlorophyll-a, chlorophyll-b, total chlorophyll,
grain yield and biological yield were different significantly among
wheat genotypes, but SPAD-chlorophyll index, relative water content
and chlorophyll florescence were not. Significant correlations were
not observed among above mentioned water relations and
chlorophyll characteristics with grain yield, but there was a positive
and significant correlation between biological yield and grain yield.
Abstract: The periodic mixed convection of a water-copper
nanofluid inside a rectangular cavity with aspect ratio of 3 is
investigated numerically. The temperature of the bottom wall of the
cavity is assumed greater than the temperature of the top lid which
oscillates horizontally with the velocity defined as u = u0 sin (ω t).
The effects of Richardson number, Ri, and volume fraction of
nanoparticles on the flow and thermal behavior of the nanofluid are
investigated. Velocity and temperature profiles, streamlines and
isotherms are presented. It is observed that when Ri < 1, heat transfer
rate is much greater than when Ri > 1. The higher value of Ri
corresponds to a lower value of the amplitude of the oscillation of
Num in the steady periodic state. Moreover, increasing the volume
fraction of the nanoparticles increases the heat transfer rate.
Abstract: Dehydration behavior gives a hint about thermal properties of materials. It is important for the usage areas and transportation of minerals. Magnesium borates can be used as additive materials in areas such as in the production of superconducting materials, in the composition of detergents, due to the content of boron in the friction-reducing additives in oils and insulating coating compositions due to their good mechanic and thermal properties.
In this study, thermal dehydration behavior of admontite (MgO(B2O3)3.7(H2O)), which is a kind of magnesium borate mineral, is experimented by microwave energy at 360W. Structure of admontite is suitable for the investigation of dehydration behavior by microwave because of its seven moles of crystal water. It is seen that admontite lost its 28.7% of weight at the end of the 120 minutes heating in microwave furnace.
Abstract: Magnesium wastes are produced by many industrial activities. This waste problem is becoming a future problem for the world. Magnesium borates have many advantages such as; high corrosion resistance, heat resistance, high coefficient of elasticity and can also be used in the production of material against radiation. Addition, magnesium borates have great potential in sectors
including ceramic and detergents industry and superconducting materials.
In this study, using the starting materials of waste magnesium and H3BO3 the hydrothermal method was applied at a moderate
temperature of 70oC. Several mole ratios of waste magnesium to H3BO3 are selected as; 1:2, 1:4, 1:6, 1:8, 1:10. Reaction time was determined as 1 hour. After the synthesis, X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR) techniques are applied to products. As a result the forms of mcallisterite “Mg2(B6O7(OH)6)2.9(H2O)”, admontite “MgO(B2O3)3.7(H2O)” and magnesium boron hydrate (MgO(B2O3)3.6(H2O)” are obtained.