Abstract: This paper was to study the clothes dryer using waste
heat from a split type air conditioner with a capacity of 12,648 btu/h.
The drying chamber had a minimum cross section area with the size
of 0.5 x 1.0 m2. The chamber was constructed by sailcloth and was
inside folded with aluminium foil. Then, it was connected to the
condensing unit of an air conditioner. The experiment was carried out
in two aspects which were the clothes drying with and without
auxiliary fan unit. The results showed that the drying rate of clothes
in the chamber installed with and without auxiliary fan unit were
2.26 and 1.1 kg/h, respectively. In case of the chamber installed with
a auxiliary fan unit, the additional power of 0.011 kWh was
consumed and the drying rate was higher than that of clothes drying
without auxiliary fan unit. Without auxiliary fan unit installation, no
energy was required but there was a portion of hot air leaks away
through the punctured holes at the wall of the drying chamber, hence
the drying rate was dropped below. The drying rate of clothes drying
using waste heat was higher than natural indoor drying and
commercial dryer which their drying rate were 0.17 and 1.9 kg/h,
respectively. It was noted that the COP of the air conditioner did not
change during the operating of clothes drying.
Abstract: The paper presents the results of microhardness and
microstructure of low carbon steel surface melted using carbon
dioxide laser with a wavelength of 10.6μm and a maximum output
power of 2000W. The processing parameters such as the laser power,
and the scanning rate were investigated in this study. After surface
melting two distinct regions formed corresponding to the melted zone
MZ, and the heat affected zone HAZ. The laser melted region
displayed a cellular fine structures while the HAZ displayed
martensite or bainite structure. At different processing parameters,
the original microstructure of this steel (Ferrite+Pearlite) has been
transformed to new phases of martensitic and bainitic structures. The
fine structure and the high microhardness are evidence of the high
cooling rates which follow the laser melting. The melting pool and
the transformed microstructure in the laser surface melted region of
carbon steel showed clear dependence on laser power and scanning
rate.
Abstract: Modeling and vibration of a flexible link manipulator
with tow flexible links and rigid joints are investigated which can
include an arbitrary number of flexible links. Hamilton principle and
finite element approach is proposed to model the dynamics of
flexible manipulators. The links are assumed to be deflection due to
bending. The association between elastic displacements of links is
investigated, took into account the coupling effects of elastic motion
and rigid motion. Flexible links are treated as Euler-Bernoulli beams
and the shear deformation is thus abandoned. The dynamic behavior
due to flexibility of links is well demonstrated through numerical
simulation. The rigid-body motion and elastic deformations are
separated by linearizing the equations of motion around the rigid
body reference path. Simulation results are shown on for both
position and force trajectory tracking tasks in the presence of varying
parameters and unknown dynamics remarkably well. The proposed
method can be used in both dynamic simulation and controller
design.
Abstract: To increase precision and reliability of automatic control systems, we have to take into account of random factors affecting the control system. Thus, operational matrix technique is used for statistical analysis of first order plus time delay system with uniform random parameter. Examples with deterministic and stochastic disturbance are considered to demonstrate the validity of the method. Comparison with Monte Carlo method is made to show the computational effectiveness of the method.
Abstract: The article presents the whole model of IS/IT
architecture exception governance. As first, the assumptions of
presented model are set. As next, there is defined a generic
governance model that serves as a basis for the architecture exception
governance. The architecture exception definition and its attributes
follow. The model respects well known approaches to the area that
are described in the text, but it adopts higher granularity in
description and expands the process view with all the next necessary
governance components as roles, principles and policies, tools to
enable the implementation of the model into organizations. The
architecture exception process is decomposed into a set of processes
related to the architecture exception lifecycle consisting of set of
phases and architecture exception states. Finally, there is information
about my future research related to this area.
Abstract: Humic acids (HAs) have been shown to activate some
ion uptakes along with stimulating the lateral roots at effective
concentration of micronutrients. However, the effects of HA on ion
adsorption by plant roots are not easily explainable due to the
varieties of HAs that differ from origins. Therefore, this study was
aimed to investigate the effect of various concentrations of HA
obtained from the compost derived from mix manures and some
agricultural wastes on the growth of eggplant seedlings (Solanum
melongena L. cv. Chao Praya) in tissue cultures at low nutrient level.
Egg plant seeds were surfaced sterilized and germinated in ½
Murashige and Skoog medium (MS) without HA added or in ¼ MS
supplemented with 0, 25, 50, 75 and 100 ppm of HAs. Then, they
were cultured for 4 weeks under the controlled environment. The
results showed that seedlings grown on ¼MS supplemented with
HAs at the concentration of 25 and 50 ppm had the average plant
heights (2.49 and 2.28 cm, respectively) higher than the other
treatments. Both treatments also significantly showed the maximum
average fresh and dry weights (p
Abstract: Bacterial cellulose, a biopolysaccharide, is produced by the bacterium, Gluconacetobacter xylinus. Static batch fermentation for bacterial cellulose production was studied in sucrose and date syrup solutions (Bx. 10%) at 28 °C using G. xylinus (PTCC, 1734). Results showed that the maximum yields of bacterial cellulose (BC) were 4.35 and 1.69 g/l00 ml for date syrup and sucrose medium after 336 hours fermentation period, respectively. Comparison of FTIR spectrum of cellulose with BC indicated appropriate coincidence which proved that the component produced by G. xylinus was cellulose. Determination of the area under X-ray diffractometry patterns demonstrated that the crystallinity amount of cellulose (83.61%) was more than that for the BC (60.73%). The scanning electron microscopy imaging of BC and cellulose were carried out in two magnifications of 1 and 6K. Results showed that the diameter ratio of BC to cellulose was approximately 1/30 which indicated more delicacy of BC fibers relative to cellulose.
Abstract: Generally flow behavior in centrifugal fan is observed
to be in a state of instability with flow separation zones on suction
surface as well as near the front shroud. Overall performance of the
diffusion process in a centrifugal fan could be enhanced by
judiciously introducing the boundary layer suction slots. With easy
accessibility of CFD as an analytical tool, an extensive numerical
whole field analysis of the effect of boundary layer suction slots in
discrete regions of suspected separation points is possible. This paper
attempts to explore the effect of boundary layer suction slots
corresponding to various geometrical locations on the impeller with
converging configurations for the slots. The analysis shows that the
converging suction slots located on the impeller blade about 25%
from the trailing edge, significantly improves the static pressure
recovery across the fan. Also it is found that Slots provided at a
radial distance of about 12% from the leading and trailing edges
marginally improve the static pressure recovery across the fan.
Abstract: Markov games are a generalization of Markov
decision process to a multi-agent setting. Two-player zero-sum
Markov game framework offers an effective platform for designing
robust controllers. This paper presents two novel controller design
algorithms that use ideas from game-theory literature to produce
reliable controllers that are able to maintain performance in presence
of noise and parameter variations. A more widely used approach for
controller design is the H∞ optimal control, which suffers from high
computational demand and at times, may be infeasible. Our approach
generates an optimal control policy for the agent (controller) via a
simple Linear Program enabling the controller to learn about the
unknown environment. The controller is facing an unknown
environment, and in our formulation this environment corresponds to
the behavior rules of the noise modeled as the opponent. Proposed
controller architectures attempt to improve controller reliability by a
gradual mixing of algorithmic approaches drawn from the game
theory literature and the Minimax-Q Markov game solution
approach, in a reinforcement-learning framework. We test the
proposed algorithms on a simulated Inverted Pendulum Swing-up
task and compare its performance against standard Q learning.
Abstract: This paper proposes the novel model order
formulation scheme to design a discrete PID controller for higher
order linear time invariant discrete systems. Modified PSO (MPSO)
based model order formulation technique has used to obtain the
successful formulated second order system. PID controller is tuned to
meet the desired performance specification by using pole-zero
cancellation and proposed design procedures. Proposed PID
controller is attached with both higher order system and formulated
second order system. System specifications are tabulated and closed
loop response is observed for stabilization process. The proposed
method is illustrated through numerical examples from literature.
Abstract: Over the past decades, automatic face recognition has become a highly active research area, mainly due to the countless application possibilities in both the private as well as the public sector. Numerous algorithms have been proposed in the literature to cope with the problem of face recognition, nevertheless, a group of methods commonly referred to as appearance based have emerged as the dominant solution to the face recognition problem. Many comparative studies concerned with the performance of appearance based methods have already been presented in the literature, not rarely with inconclusive and often with contradictory results. No consent has been reached within the scientific community regarding the relative ranking of the efficiency of appearance based methods for the face recognition task, let alone regarding their susceptibility to appearance changes induced by various environmental factors. To tackle these open issues, this paper assess the performance of the three dominant appearance based methods: principal component analysis, linear discriminant analysis and independent component analysis, and compares them on equal footing (i.e., with the same preprocessing procedure, with optimized parameters for the best possible performance, etc.) in face verification experiments on the publicly available XM2VTS database. In addition to the comparative analysis on the XM2VTS database, ten degraded versions of the database are also employed in the experiments to evaluate the susceptibility of the appearance based methods on various image degradations which can occur in "real-life" operating conditions. Our experimental results suggest that linear discriminant analysis ensures the most consistent verification rates across the tested databases.
Abstract: This paper study the behavior of the solution at the crack edges for an elliptical crack with developing cusps, Ω in the plane elasticity subjected to shear loading. The problem of finding the resulting shear stress can be formulated as a hypersingular integral equation over Ω and it is then transformed into a similar equation over a circular region, D, using conformal mapping. An appropriate collocation points are chosen on the region D to reduce the hypersingular integral equation into a system of linear equations with (2N+1)(N+1) unknown coefficients, which will later be used in the determination of shear stress intensity factors and maximum shear stress intensity. Numerical solution for the considered problem are compared with the existing asymptotic solution, and displayed graphically. Our results give a very good agreement to the existing asymptotic solutions.
Abstract: It can be said that the business sector is faced with a range of challenges–a rapidly changing business environment, an increase and diversification of customers- demands and the consequent need for quick response–for having in place flexible management and production info systems. As a matter of fact, many manufacturers have adopted production info management systems such as MES and ERP. Nevertheless, managers are having difficulties obtaining ever-changing production process information in real time, or responding quickly to any change in production related needs on the basis of such information. This is because they rely on poor production info systems which are not capable of providing real-time factory settings. If the manufacturer doesn-t have a capacity for collecting or digitalizing the 4 Ms (Man, Machine, Material, Method), which are resources for production, on a real time basis, it might to difficult to effectively maintain the information on production process. In this regard, this paper will introduce some new alternatives to the existing methods of collecting the 4 Ms in real time, which are currently comprise the production field.
Abstract: Enterprise applications are complex systems that are hard to develop and deploy in organizations. Although software application development tools, frameworks, methodologies and patterns are rapidly developing; many projects fail by causing big costs. There are challenging issues that programmers and designers face with while working on enterprise applications. In this paper, we present the three of the significant issues: Architectural, technological and performance. The important subjects in each issue are pointed out and recommendations are given. In architectural issues the lifecycle, meta-architecture, guidelines are pointed out. .NET and Java EE platforms are presented in technological issues. The importance of performance, measuring performance and profilers are explained in performance issues.
Abstract: The move towards internationalization of accounting encountered a great boost, when in 2002 EU delegated the IASB to provide the accounting standards to be applied inside its frontiers. Among the incentives of the standardization of accounting on the international level, is the reduction of the cost of capital. Romania made the move towards IFRS before EU, when the country was not yet a member of it. Even if this made Romania a special case, it was scarcely approached. The leak of real data is usually the reason for avoiding. The novelty of this paper is that it offers an insight from the reality of Romanian companies and their view regarding the IFRS. The paper is based on a survey that the authors made among the companies listed on the first two tiers of the Bucharest Stock Exchange (BSE), which are basically, the most important companies in the country.
Abstract: In this paper, we proposed the direct method for converting
Finite-Impulse Response (FIR) filter with low nonzero tap
into Infinite-Impulse Response (IIR) filter using the pre-determined
table. The prony method is used by ghost cancellator which is IIR
approximation to FIR filter which is better performance than IIR and
have much larger calculation difference. The direct method for many
ghost combination with low nonzero tap of NTSC(National Television
System Committee) TV signal in Korea is described. The proposed
method is illustrated with an example.
Abstract: In this paper, a three dimensional autonomous chaotic system is considered. The existence of Hopf bifurcation is investigated by choosing the appropriate bifurcation parameter. Furthermore, formulas for determining the direction of the Hopf bifurcation and the stability of bifurcating periodic solutions are derived with the help of normal form theory. Finally, a numerical example is given.
Abstract: Background: Regular physical activity contributes
positively to physical and psychological health. In the present study,
the stages of change of physical activity and the total physical
Aims: The aim of this study was to investigate the proportion of
adolescent girls in each stages of change and the causative factors
associated with physical activity such as the related social support
and self efficacy in a sample of the high school students.
Methods: In this study, Social Cognitive Theory (SCT) and the
Transtheorical Model (TTM) guided instrument development. The
data regarding the demographics, psychosocial determinants of
physical activity, stage of change and physical activity was gathered
by questionnaires. Several measures of psychosocial determinants of
physical activity were translated from English into Persian using the
back-translation technique. These translated measures were
administered to 512 ninth and tenth-grade Iranian high school
students for factor analysis.
Results: The distribution of the stage of change for physical activity
was as follow: 18/5% in precontemplation, 23.4% in contemplation,
38.2% in preparation, 4.6% in action and 15.3% in maintenance.
They were in 80.1% pre-adoption stages (precontemplation stage,
contemplation stage and preparation stage) and 19.9% post-adoption
stages (action stage and maintenance stage) of physical activity.
There was a significant relate between age and physical activity in
adolescent girls (age-related decline of physical activity) p
Abstract: this article proposed a methodology for computer
numerical control (CNC) machine scoring. The case study company
is a manufacturer of hard disk drive parts in Thailand. In this
company, sample of parts manufactured from CNC machine are
usually taken randomly for quality inspection. These inspection data
were used to make a decision to shut down the machine if it has
tendency to produce parts that are out of specification. Large amount
of data are produced in this process and data mining could be very
useful technique in analyzing them. In this research, data mining
techniques were used to construct a machine scoring model called
'machine priority assessment model (MPAM)'. This model helps to
ensure that the machine with higher risk of producing defective parts
be inspected before those with lower risk. If the defective prone
machine is identified sooner, defective part and rework could be
reduced hence improving the overall productivity. The results
showed that the proposed method can be successfully implemented
and approximately 351,000 baht of opportunity cost could have
saved in the case study company.
Abstract: Tanzania secondary schools in rural areas are geographically and socially isolated, hence face a number of problems in getting learning materials resulting in poor performance in National examinations. E-learning as defined to be the use of information and communication technology (ICT) for supporting the educational processes has motivated Tanzania to apply ICT in its education system. There has been effort to improve secondary school education using ICT through several projects. ICT for e-learning to Tanzania rural secondary school is one of the research projects conceived by the University of Dar-es-Salaam through its College of Engineering and Technology. The main objective of the project is to develop a tool to enable ICT support rural secondary school. The project is comprehensive with a number of components, one being development of e-learning management system (e-LMS) for Tanzania secondary schools. This paper presents strategies of developing e-LMS. It shows the importance of integrating action research methodology with the modeling methods as presented by model driven architecture (MDA) and the usefulness of Unified Modeling Language (UML) on the issue of modeling. The benefit of MDA will go along with the development based on software development life cycle (SDLC) process, from analysis and requirement phase through design and implementation stages as employed by object oriented system analysis and design approach. The paper also explains the employment of open source code reuse from open source learning platforms for the context sensitive development of the e-LMS for Tanzania secondary schools.