Abstract: A brushless DC motor with integrated drive circuit for air management system is presented. Using magnetic equivalent circuit model a basic design of the motor is determined, and specific configurations are inspected thanks to finite element analysis. In order to reduce an unbalanced magnetic force in an axial direction, induced forces between a stator core and a permanent magnet are calculated with respect to the relative positions of them. For the high efficiency, and high power density, BLDC motor and drive are developed. Also vibration mode and eccentricity of a rotor are considered at the rated and maximum rotational speed Through the experimental results, a validity of the simulated one is confirmed.
Abstract: This paper presented a novel combined cycle of air separation and natural gas liquefaction. The idea is that natural gas can be liquefied, meanwhile gaseous or liquid nitrogen and oxygen are produced in one combined cryogenic system. Cycle simulation and exergy analysis were performed to evaluate the process and thereby reveal the influence of the crucial parameter, i.e., flow rate ratio through two stages expanders β on heat transfer temperature difference, its distribution and consequent exergy loss. Composite curves for the combined hot streams (feeding natural gas and recycled nitrogen) and the cold stream showed the degree of optimization available in this process if appropriate β was designed. The results indicated that increasing β reduces temperature difference and exergy loss in heat exchange process. However, the maximum limit value of β should be confined in terms of minimum temperature difference proposed in heat exchanger design standard and heat exchanger size. The optimal βopt under different operation conditions corresponding to the required minimum temperature differences was investigated.
Abstract: Cavitation in pumps is known as the formation of
vapor bubbles due to pressure drop and collapsing these bubbles. In
some conditions, it has been observed that the formation of bubbles
occurs at the pressure side of centrifugal pump blades. In this study,
the formation of bubbles at the pressure side of blades has been
investigated. Water is used in this study as the fluid and performance
curves were depicted for different flow rates in an approximately
constant speed. The results show that when a centrifugal pump works
in low flow rates, a secondary flow namely recirculation starts to
begin. In this condition, separation of flow increases which causes
vortex formation and local pressure drop and eventually the
formation of vapor bubbles starts.
Abstract: These Nowadays the explosion of bombs or explosive
materials such as gas and oil near or inside the buildings cause some
losses in installations and building components. This has made the
engineers to make the buildings and their components resistance
against the effects of explosion. These activities lead to provide
regulations and different methods. The above regulations are mostly
focused on the explosion effects resulting from the vehicles around
the buildings. Therefore, the explosion resulting from the vehicles
outside the buildings will be studied in this research.
In the present study, the main goals are to investigate the
explosion load effects on the structures located on the piles with the
specific quantity of plasticity and observing the permissible response
of these structures. The concentrated mass system and the spring with
two degree of freedom will be used to study the structural system.
Abstract: The anti-lock braking systems installed on vehicles
for safe and effective braking, are high-order nonlinear and timevariant.
Using fuzzy logic controllers increase efficiency of such
systems, but impose a high computational complexity as well. The
main concept introduced by this paper is reducing computational
complexity of fuzzy controllers by deploying problem-solution data
structure. Unlike conventional methods that are based on
calculations, this approach is based on data oriented modeling.
Abstract: Relay based communication has gained considerable importance in the recent years. In this paper we find the end-toend statistics of a two hop non-regenerative relay branch, each hop being Nakagami-m faded. Closed form expressions for the probability density functions of the signal envelope at the output of a selection combiner and a maximal ratio combiner at the destination node are also derived and analytical formulations are verified through computer simulation. These density functions are useful in evaluating the system performance in terms of bit error rate and outage probability.
Abstract: Cardiovascular disease mostly in the form of atherosclerosis is responsible for 30% of all world deaths amounting to 17 million people per year. Atherosclerosis is due to the formation of plaque. The fatty plaque may be at risk of rupture, leading typically to stroke and heart attack. The plaque is usually associated with a high degree of lumen reduction, called a stenosis. The initiation and progression of the disease is strongly linked to the hemodynamic environment near the vessel wall. The aim of this study is to validate the flow of blood mimic through an arterial stenosis model with computational fluid dynamics (CFD) package. In experiment, an axisymmetric model constructed consists of contraction and expansion region that follow a mathematical form of cosine function. A 30% diameter reduction was used in this study. Particle image velocimetry (PIV) was used to characterize the flow. The fluid consists of rigid spherical particles suspended in waterglycerol- NaCl mixture. The particles with 20 μm diameter were selected to follow the flow of fluid. The flow at Re=155, 270 and 390 were investigated. The experimental result is compared with FLUENT simulated flow that account for viscous laminar flow model. The results suggest that laminar flow model was sufficient to predict flow velocity at the inlet but the velocity at stenosis throat at Re =390 was overestimated. Hence, a transition to turbulent regime might have been developed at throat region as the flow rate increases.
Abstract: The purpose of this study is two-fold. First, it attempts to explore potential opportunities for utilizing visual interactive simulations along with Business Intelligence (BI) as a decision support tool for strategic decision making. Second, it tries to figure out the essential top-level managerial requirements that would transform strategic decision simulation into an integral component of BI systems. The domain of particular interest was the application of visual interactive simulation capabilities in the field of supply chains. A qualitative exploratory method was applied, through the use of interviews with two leading companies. The collected data was then analysed to demonstrate the difference between the literature perspective and the practical managerial perspective on the issue. The results of the study suggest that although the use of simulation particularly in managing supply chains is very evident in literature, yet, in practice such utilization is still in its infancy, particularly regarding strategic decisions. Based on the insights a prototype of a simulation based BI-solution-extension was developed and evaluated.
Abstract: This paper proposes a new methodology for the
optimal allocation and sizing of Embedded Generation (EG)
employing Real Coded Genetic Algorithm (RCGA) to minimize the
total power losses and to improve voltage profiles in the radial
distribution networks. RCGA is a method that uses continuous
floating numbers as representation which is different from
conventional binary numbers. The RCGA is used as solution tool,
which can determine the optimal location and size of EG in radial
system simultaneously. This method is developed in MATLAB. The
effect of EG units- installation and their sizing to the distribution
networks are demonstrated using 24 bus system.
Abstract: Formaldehyde is the illegal chemical substance used
for food preservation in fish and vegetable. It can promote
carcinogenesis. Superoxide dismutases are the important
antioxidative enzymes that catalyze the dismutation of superoxide
anion into oxygen and hydrogen peroxide. The resultant level of
oxidative stress in formaldehyde-treated lymphocytes was
investigated. The formaldehyde concentrations of 0, 20, 40, 60, 80
and 120μmol/L were treated in human lymphocytes for 12 hours.
After 12 treated hours, the superoxide dismutase activity change was
measured in formaldehyde-treated lymphocytes. The results showed
that the formaldehyde concentrations of 60, 80 and 120μmol/L
significantly decreased superoxide dismutase activities in
lymphocytes (P < 0.05). The change of superoxide dismutase
activity in formaldehyde-treated lymphocytes may be the biomarker
for detect cellular injury, such as damage to DNA, due to
formaldehyde exposure.
Abstract: It has formed an essential issue that Climate Change, composed of highly knowledge complexity, reveals its significant impact on human existence. Therefore, specific national policies, some of which present the educational aspects, have been published for overcoming the imperative problem. Accordingly, the study aims to analyze as well as integrate the relationship between Climate Change and environmental education and apply the perspective of concept map to represent the knowledge contents and structures of Climate Change; by doing so, knowledge contents of Climate Change could be represented in an even more comprehensive way and manipulated as the tool for environmental education. The method adapted for this study is knowledge conversion model compounded of the platform for experts and teachers, who were the participants for this study, to cooperate and combine each participant-s standpoints into a complete knowledge framework that is the foundation for structuring the concept map. The result of this research contains the important concepts, the precise propositions and the entire concept map for representing the robust concepts of Climate Change.
Abstract: A state of the art Speaker Identification (SI) system
requires a robust feature extraction unit followed by a speaker
modeling scheme for generalized representation of these features.
Over the years, Mel-Frequency Cepstral Coefficients (MFCC)
modeled on the human auditory system has been used as a standard
acoustic feature set for speech related applications. On a recent
contribution by authors, it has been shown that the Inverted Mel-
Frequency Cepstral Coefficients (IMFCC) is useful feature set for
SI, which contains complementary information present in high
frequency region. This paper introduces the Gaussian shaped filter
(GF) while calculating MFCC and IMFCC in place of typical
triangular shaped bins. The objective is to introduce a higher
amount of correlation between subband outputs. The performances
of both MFCC & IMFCC improve with GF over conventional
triangular filter (TF) based implementation, individually as well as
in combination. With GMM as speaker modeling paradigm, the
performances of proposed GF based MFCC and IMFCC in
individual and fused mode have been verified in two standard
databases YOHO, (Microphone Speech) and POLYCOST
(Telephone Speech) each of which has more than 130 speakers.
Abstract: This paper focuses on the Mega-Sub Controlled
Structure Systems (MSCSS) performances and characteristics
regarding the new control principle contained in MSCSS subjected to
strong earthquake excitations. The adopted control scheme consists of
modulated sub-structures where the control action is achieved by
viscous dampers and sub-structure own configuration. The
elastic-plastic time history analysis under severe earthquake excitation
is analyzed base on the Finite Element Analysis Method (FEAM), and
some comparison results are also given in this paper. The result shows
that the MSCSS systems can remarkably reduce vibrations effects
more than the mega-sub structure (MSS). The study illustrates that the
improved MSCSS presents good seismic resistance ability even at 1.2g
and can absorb seismic energy in the structure, thus imply that
structural members cross section can be reduce and achieve to good
economic characteristics. Furthermore, the elasto-plastic analysis
demonstrates that the MSCSS is accurate enough regarding
international building evaluation and design codes. This paper also
shows that the elasto-plastic dynamic analysis method is a reasonable
and reliable analysis method for structures subjected to strong
earthquake excitations and that the computed results are more precise.
Abstract: Traffic congestion has become a major problem in
many countries. One of the main causes of traffic congestion is due
to road merges. Vehicles tend to move slower when they reach the
merging point. In this paper, an enhanced algorithm for traffic
simulation based on the fluid-dynamic algorithm and kinematic wave
theory is proposed. The enhanced algorithm is used to study traffic
congestion at a road merge. This paper also describes the
development of a dynamic traffic simulation tool which is used as a
scenario planning and to forecast traffic congestion level in a certain
time based on defined parameter values. The tool incorporates the
enhanced algorithm as well as the two original algorithms. Output
from the three above mentioned algorithms are measured in terms of
traffic queue length, travel time and the total number of vehicles
passing through the merging point. This paper also suggests an
efficient way of reducing traffic congestion at a road merge by
analyzing the traffic queue length and travel time.
Abstract: This study was designed to formulate,
pharmaceutically evaluate a topical skin-care cream (w/o emulsion)
of Aloe Vera versus its vehicle (Base) as control and determine their
effects on Stratum Corneum (SC) water content and Transepidermal
water loss (TEWL). Base containing no extract and a Formulation
containing 3% concentrated extract of Aloe Vera was developed by
entrapping in the inner aqueous phase of w/o emulsion (cream).
Lemon oil was incorporated to improve the odor. Both the Base and
Formulation were stored at 8°C ±0.1°C (in refrigerator), 25°C±0.1°C,
40°C±0.1°C and 40°C± 0.1°C with 75% RH (in incubator) for a
period of 4 weeks to predict their stability. The evaluation parameters
consisted of color, smell, type of emulsion, phase separation,
electrical conductivity, centrifugation, liquefaction and pH. Both the
Base and Formulation were applied to the cheeks of 21 healthy
human volunteers for a period of 8 weeks Stratum corneum (SC)
water content and Transepidermal water loss (TEWL) were
monitored every week to measure any effect produced by these
topical creams. The expected organoleptic stability of creams was
achieved from 4 weeks in-vitro study period. Odor was disappeared
with the passage of time due to volatilization of lemon oil. Both the
Base and Formulation produced significant (p≤0.05) changes in
TEWL with respect to time. SC water content was significantly
(p≤0.05) increased by the Formulation while the Base has
insignificant (p 0.05) effects on SC water content. The newly
formulated cream of Aloe Vera, applied is suitable for improvement
and quantitative monitoring of skin hydration level (SC water
content/ moisturizing effects) and reducing TEWL in people with dry
skin.
Abstract: Six parameters, the effective diffusivity (De),
activation energy of De, pre-exponential factor of De, amount
(ASOW) of self-organized water species, and amplitude (α) of the
forced oscillation of the molecular mobility (1/tC) derived from the
forced cyclic temperature change operation, were characterized by
using six typical foods, squid, sardines, scallops, salmon, beef, and
pork, as a function of the correlation time (tC) of the water molecule-s
proton retained in the foods. Each of the six parameters was clearly
divided into the water species A1 and A2 at a specified value of tC
=10-8s (=CtC), indicating an anomalous change in the physicochemical
nature of the water species at the CtC. The forced oscillation of 1/tC
clearly demonstrated a characteristic mode depending on the food
shown as a three dimensional map associated with 1/tC, the amount of
self-organized water, and tC.
Abstract: Size based filtration is one of the common methods
employed to isolate circulating tumor cells (CTCs) from whole
blood. It is well known that this method suffers from isolation
efficiency to purity tradeoff. However, this tradeoff is poorly
understood. In this paper, we present the design and manufacturing
of a special rectangular slit filter. The filter was designed to retain
maximal amounts of nucleated cells, while minimizing the pressure
on cells, thereby preserving their morphology. The key parameter,
namely, input pressure, was optimized to retain the maximal number
of tumor cells, whilst maximizing the depletion of normal blood cells
(red and white blood cells and platelets). Our results indicate that for
a slit geometry of 5 × 40 μm on a 13 mm circular membrane with a
fill factor of 21%, a pressure of 6.9 mBar yields the optimum for
maximizing isolation of MCF-7 and depletion of normal blood cells.
Abstract: The environment pollution with pesticides and heavy
metals is a recognized problem nowadays, with extension to the
global scale the tendency of amplification. Even with all the progress
in the environmental field, both in the emphasize of the effect of the
pollutants upon health, the linked studies environment-health are
insufficient, not only in Romania but all over the world also. We aim
to describe the particular situation in Romania regarding the
uncontrolled use of pesticides, to identify and evaluate the risk zones
for health and the environment in Romania, with the final goal of
designing adequate programs for reduction and control of the risk
sources. An exploratory study was conducted to determine the
magnitude of the pesticide use problem in a population living in
Saliste, a rural setting in Transylvania, Romania. The significant
stakeholders in Saliste region were interviewed and a sample from
the population living in Saliste area was selected to fill in a designed
questionnaire. All the selected participants declared that they used
pesticides in their activities for more than one purpose. They
declared they annually applied pesticides for a period of time
between 11 and 30 years, from 5 to 9 days per year on average,
mainly on crops situated at some distance from the houses but high
risk behavior was identified as the volunteers declared the use of
pesticides in the backyard gardens, near their homes, where children
were playing. The pesticide applicators did not have the necessary
knowledge about safety and exposure. The health data must be
correlated with exposure biomarkers in attempt to identify the
possible health effects of the pesticides exposure. Future plans
include educational campaigns to raise the awareness of the
population on the danger of uncontrolled use of pesticides.
Abstract: This paper presents an adaptive technique for generation
of data required for construction of artificial neural network-based
performance model of nano-scale CMOS inverter circuit. The training
data are generated from the samples through SPICE simulation. The
proposed algorithm has been compared to standard progressive sampling
algorithms like arithmetic sampling and geometric sampling.
The advantages of the present approach over the others have been
demonstrated. The ANN predicted results have been compared with
actual SPICE results. A very good accuracy has been obtained.
Abstract: Increasing the demand for effectively use of the
production facility requires the tools for sharing the manufacturing
facility through remote operation of the machining process. This
research introduces the methodology of machining technology for
direct remote operation of networked milling machine. The
integrated tools with virtual simulation, remote desktop protocol and
Setup Free Attachment for remote operation of milling process are
proposed. Accessing and monitoring of machining operation is
performed by remote desktop interface and 3D virtual simulations.
Capability of remote operation is supported by an auto setup
attachment with a reconfigurable pin type setup free technology
installed on the table of CNC milling machine to perform unattended
machining process. The system is designed using a computer server
and connected to a PC based controlled CNC machine for real time
monitoring. A client will access the server through internet
communication and virtually simulate the machine activity. The
result has been presented that combination between real time virtual
simulation and remote desktop tool is enabling to operate all machine
tool functions and as well as workpiece setup..