Abstract: Data security in u-Health system can be an important
issue because wireless network is vulnerable to hacking. However, it is
not easy to implement a proper security algorithm in an embedded
u-health monitoring because of hardware constraints such as low
performance, power consumption and limited memory size and etc. To
secure data that contain personal and biosignal information, we
implemented several security algorithms such as Blowfish, data
encryption standard (DES), advanced encryption standard (AES) and
Rivest Cipher 4 (RC4) for our u-Health monitoring system and the
results were successful. Under the same experimental conditions, we
compared these algorithms. RC4 had the fastest execution time.
Memory usage was the most efficient for DES. However, considering
performance and safety capability, however, we concluded that AES
was the most appropriate algorithm for a personal u-Health monitoring
system.
Abstract: Isobaric and cooling zone of iron ore reactor have been
simulated. In this paper, heat and mass transfer equation are
formulated to perform the temperature and concentration of gas and
solid phase respectively. Temperature profile for isobaric zone is
simulated on the range temperature of 873-1163K while cooling zone
is simulated on the range temperature of 733-1139K. The simulation
results have a good agreement with the plant data. Total carbon
formation in the isobaric zone is only 30% of total carbon contained in
the sponge iron product. The formation of Fe3C in isobaric zone
reduces metallization degree up to 0.58% whereas reduction of
metallization degree in cooling zone up to 1.139%. The decreasing of
sponge iron temperature in the isobaric and cooling zone is around 300
K and 600 K respectively.
Abstract: This paper describes the development, modeling, and
testing of skyhook and MiniMax control strategies of semi-active
suspension. The control performances are investigated using
Matlab/Simulink [1], with a two-degree-of-freedom quarter car semiactive
suspension system model. The comparison and evaluation of
control result are made using software-in-the-loop simulation (SILS)
method. This paper also outlines the development of a hardware-inthe-
loop simulation (HILS) system. The simulation results show that
skyhook strategy can significantly reduce the resonant peak of body
and provide improvement in vehicle ride comfort. Otherwise,
MiniMax strategy can be employed to effectively improve drive
safety of vehicle by influencing wheel load. The two strategies can
be switched to control semi-active suspension system to fulfill
different requirement of vehicle in different stages.
Abstract: Large metal and concrete structures suffer by various kinds of deterioration, and accurate prediction of the remaining life is important. This paper informs about two methods for its assessment. One method, suitable for steel bridges and other constructions exposed to fatigue, monitors the loads and damage accumulation using information systems for the operation and the finite element model of the construction. In addition to the operation load, the dead weight of the construction and thermal stresses can be included into the model. The second method is suitable for concrete bridges and other structures, which suffer by carbonatation and other degradation processes, driven by diffusion. The diffusion constant, important for the prediction of future development, can be determined from the depth-profile of pH, obtained by pH measurement at various depths. Comparison with measurements on real objects illustrates the suitability of both methods.
Abstract: Air conditioning systems of houses consume large
quantity of electricity. To reducing energy consumption for air
conditioning purposes it is becoming attractive the use of evaporative
cooling air conditioning which is less energy consuming compared to
air chillers. But, it is obvious that higher energy efficiency of
evaporative cooling is not enough to judge whether evaporative
cooling economically is competitive with other types of cooling
systems. To proving the higher energy efficiency and cost
effectiveness of the evaporative cooling competitive analysis of
various types of cooling system should be accomplished. For noted
purpose optimization mathematical model for each system should be
composed based on system approach analysis. In this paper different
types of evaporative cooling-heating systems are discussed and
methods for increasing their energy efficiency and as well as
determining of their design parameters are developed. The
optimization mathematical models for each of them are composed
with help of which least specific costs for each of them are reviled.
The comparison of specific costs proved that the most efficient and
cost effective is considered the “direct evaporating" system if it is
applicable for given climatic conditions. Next more universal and
applicable for many climatic conditions system providing least cost
of heating and cooling is considered the “direct evaporating" system.
Abstract: Data mining can be called as a technique to extract
information from data. It is the process of obtaining hidden
information and then turning it into qualified knowledge by statistical
and artificial intelligence technique. One of its application areas is
medical area to form decision support systems for diagnosis just by
inventing meaningful information from given medical data. In this
study a decision support system for diagnosis of illness that make use
of data mining and three different artificial intelligence classifier
algorithms namely Multilayer Perceptron, Naive Bayes Classifier and
J.48. Pima Indian dataset of UCI Machine Learning Repository was
used. This dataset includes urinary and blood test results of 768
patients. These test results consist of 8 different feature vectors.
Obtained classifying results were compared with the previous studies.
The suggestions for future studies were presented.
Abstract: In this research a mathematical model for direct
oxidization of hydrogen sulfide into elemental sulfur in a fluidized
bed reactor with external circulation was developed. As the catalyst
is deactivated in the fluidized bed, it might be placed in a reduction
tank in order to remove sulfur through heating above its dew point.
The reactor model demonstrated via MATLAB software. It was
shown that variations of H2S conversion as well as; products formed
were reasonable in comparison with corresponding results of a fixed
bed reactor. Through analyzing results of this model, it became
possible to propose the main optimized operating conditions for the
process considered. These conditions included; the temperature range
of 100-130ºC and utilizing the catalyst as much as possible providing
the highest bed density respect to dimensions of bed, economical
aspects that the bed ever remained in fluidized mode. A high active
and stable catalyst under the optimum conditions exhibited 100%
conversion in a fluidized bed reactor.
Abstract: Requirement engineering has been the subject of large
volume of researches due to the significant role it plays in the
software development life cycle. However, dynamicity of software
industry is much faster than advances in requirements engineering
approaches. Therefore, this paper aims to systematically review and
evaluate the current research in requirement engineering and identify
new research trends and direction in this field. In addition, various
research methods associated with the Evaluation-based techniques
and empirical study are highlighted for the requirements engineering
field. Finally, challenges and recommendations on future directions
research are presented based on the research team observations
during this study.
Abstract: The aim of this research is to determine how preservice Turkish teachers perceive themselves in terms of problem solving skills. Students attending Department of Turkish Language Teaching of Gazi University Education Faculty in 2005-2006 academic year constitute the study group (n= 270) of this research in which survey model was utilized. Data were obtained by Problem Solving Inventory developed by Heppner & Peterson and Personal Information Form. Within the settings of this research, Cronbach Alpha reliability coefficient of the scale was found as .87. Besides, reliability coefficient obtained by split-half technique which splits odd and even numbered items of the scale was found as r=.81 (Split- Half Reliability). The findings of the research revealed that preservice Turkish teachers were sufficiently qualified on the subject of problem solving skills and statistical significance was found in favor of male candidates in terms of “gender" variable. According to the “grade" variable, statistical significance was found in favor of 4th graders.
Abstract: Wireless sensor networks are consisted of hundreds or
thousands of small sensors that have limited resources.
Energy-efficient techniques are the main issue of wireless sensor
networks. This paper proposes an energy efficient agent-based
framework in wireless sensor networks. We adopt biologically
inspired approaches for wireless sensor networks. Agent operates
automatically with their behavior policies as a gene. Agent aggregates
other agents to reduce communication and gives high priority to nodes
that have enough energy to communicate. Agent behavior policies are
optimized by genetic operation at the base station. Simulation results
show that our proposed framework increases the lifetime of each node.
Each agent selects a next-hop node with neighbor information and
behavior policies. Our proposed framework provides self-healing,
self-configuration, self-optimization properties to sensor nodes.
Abstract: The construction of a civil structure inside a urban
area inevitably modifies the outdoor microclimate at the building
site. Wind speed, wind direction, air pollution, driving rain, radiation
and daylight are some of the main physical aspects that are subjected
to the major changes. The quantitative amount of these modifications
depends on the shape, size and orientation of the building and on its
interaction with the surrounding environment.The flow field over a
flat roof model building has been numerically investigated in order to
determine two-dimensional CFD guidelines for the calculation of the
turbulent flow over a structure immersed in an atmospheric boundary
layer. To this purpose, a complete validation campaign has been
performed through a systematic comparison of numerical simulations
with wind tunnel experimental data.Several turbulence models and
spatial node distributions have been tested for five different vertical
positions, respectively from the upstream leading edge to the
downstream bottom edge of the analyzed model. Flow field
characteristics in the neighborhood of the building model have been
numerically investigated, allowing a quantification of the capabilities
of the CFD code to predict the flow separation and the extension of
the recirculation regions.The proposed calculations have allowed the
development of a preliminary procedure to be used as a guidance in
selecting the appropriate grid configuration and corresponding
turbulence model for the prediction of the flow field over a twodimensional
roof architecture dominated by flow separation.
Abstract: In this paper, we show that the association of the PI
regulators for the speed and stator currents with a control strategy
using the linearization by state feedback for an induction machine
without speed sensor, and with an adaptation of the rotor resistance.
The rotor speed is estimated by using the model reference adaptive
system approach (MRAS). This method consists of using two
models: The first is the reference model and the second is an
adjustable one in which two components of the stator flux, obtained
from the measurement of the currents and stator voltages are
estimated. The estimated rotor speed is then obtained by canceling
the difference between stator-flux of the reference model and those
of the adjustable one. Satisfactory results of simulation are obtained
and discussed in this paper to highlight the proposed approach.
Abstract: This paper gives an overview of a deep drawing
process by pressurized liquid medium separated from the sheet by a
rubber diaphragm. Hydroforming deep drawing processing of sheet
metal parts provides a number of advantages over conventional
techniques. It generally increases the depth to diameter ratio possible
in cup drawing and minimizes the thickness variation of the drawn
cup. To explore the deformation mechanism, analytical and
numerical simulations are used for analyzing the drawing process of
an AA6061-T4 blank. The effects of key process parameters such as
coefficient of friction, initial thickness of the blank and radius
between cup wall and flange are investigated analytically and
numerically. The simulated results were in good agreement with the
results of the analytical model. According to finite element
simulations, the hydroforming deep drawing method provides a more
uniform thickness distribution compared to conventional deep
drawing and decreases the risk of tearing during the process.
Abstract: In this paper, fully developed flow and heat transfer of
viscoelastic materials in curved ducts with square cross section under
constant heat flux have been investigated. Here, staggered mesh is
used as computational grids and flow and heat transfer parameters
have been allocated in this mesh with marker and cell method.
Numerical solution of governing equations has being performed with
FTCS finite difference method. Furthermore, Criminale-Eriksen-
Filbey (CEF) constitutive equation has being used as viscoelastic
model. CEF constitutive equation is a suitable model for studying
steady shear flow of viscoelastic materials which is able to model
both effects of the first and second normal stress differences. Here, it
is shown that the first and second normal stresses differences have
noticeable and inverse effect on secondary flows intensity and mean
Nusselt number which is the main novelty of current research.
Abstract: Modeling of the distributed systems allows us to
represent the whole its functionality. The working system instance
rarely fulfils the whole functionality represented by model; usually
some parts of this functionality should be accessible periodically.
The reporting system based on the Data Warehouse concept seams to
be an intuitive example of the system that some of its functionality is
required only from time to time. Analyzing an enterprise risk
associated with the periodical change of the system functionality, we
should consider not only the inaccessibility of the components
(object) but also their functions (methods), and the impact of such a
situation on the system functionality from the business point of view.
In the paper we suggest that the risk attributes should be estimated
from risk attributes specified at the requirements level (Use Case in
the UML model) on the base of the information about the structure of
the model (presented at other levels of the UML model). We argue
that it is desirable to consider the influence of periodical changes in
requirements on the enterprise risk estimation. Finally, the
proposition of such a solution basing on the UML system model is
presented.
Abstract: In this article, a mathematical programming model
for choosing an optimum portfolio of investments is developed.
The investments are considered as investment projects. The
uncertainties of the real world are associated through fuzzy
concepts for coefficients of the proposed model (i. e. initial
investment costs, profits, resource requirement, and total available
budget). Model has been coded by using LINGO 11.0 solver. The
results of a full analysis of optimistic and pessimistic derivative
models are promising for selecting an optimum portfolio of
projects in presence of uncertainty.
Abstract: In the effort to reduce water consumption for resorts,
more water conservation practices need to be implemented. Hence
water audits need to be performed to obtain a baseline of water
consumption, before planning water conservation practices. In this
study, a water audit framework specifically for resorts was created,
and the audit was performed on two resorts: Resort A in Langkawi,
Malaysia; and Resort B in Miri, Malaysia. From the audit, the total
daily water consumption for Resorts A and B were estimated to be
180m3 and 330 m3 respectively, while the actual water consumption
(based on water meter readings) were 175 m3 and 325 m3. This
suggests that the audit framework is reasonably accurate and may be
used to account for most of the water consumption sources in a
resort. The daily water consumption per guest is about 500 litres. The
water consumption of both resorts is poorly rated compared with
established benchmarks. Water conservation measures were
suggested for both resorts.
Abstract: Trends in business intelligence, e-commerce and
remote access make it necessary and practical to store data in
different ways on multiple systems with different operating systems.
As business evolve and grow, they require efficient computerized
solution to perform data update and to access data from diverse
enterprise business applications. The objective of this paper is to
demonstrate the capability of DTS [1] as a database solution for
automatic data transfer and update in solving business problem. This
DTS package is developed for the sales of variety of plants and
eventually expanded into commercial supply and landscaping
business. Dimension data modeling is used in DTS package to
extract, transform and load data from heterogeneous database
systems such as MySQL, Microsoft Access and Oracle that
consolidates into a Data Mart residing in SQL Server. Hence, the
data transfer from various databases is scheduled to run automatically
every quarter of the year to review the efficient sales analysis.
Therefore, DTS is absolutely an attractive solution for automatic data
transfer and update which meeting today-s business needs.
Abstract: In this paper, stabilization of an Active Magnetic Bearing (AMB) system with varying rotor speed using Sliding Mode Control (SMC) technique is considered. The gyroscopic effect inherited in the system is proportional to rotor speed in which this nonlinearity effect causes high system instability as the rotor speed increases. Also, transformation of the AMB dynamic model into a new class of uncertain system shows that this gyroscopic effect lies in the mismatched part of the system matrix. Moreover, the current gain parameter is allowed to be varied in a known bound as an uncertainty in the input matrix. SMC design method is proposed in which the sufficient condition that guarantees the global exponential stability of the reduced-order system is represented in Linear Matrix Inequality (LMI). Then, a new chattering-free control law is established such that the system states are driven to reach the switching surface and stay on it thereafter. The performance of the controller applied to the AMB model is demonstrated through simulation works under various system conditions.
Abstract: Flow through micro and mini channels requires relatively
high driving pressure due to the large fluid pressure drop
through these channels. Consequently the forces acting on the walls of
the channel due to the fluid pressure are also large. Due to these forces
there are displacement fields set up in the solid substrate containing
the channels. If the movement of the substrate is constrained at some
points, then stress fields are established in the substrate. On the other
hand, if the deformation of the channel shape is sufficiently large
then its effect on the fluid flow is important to be calculated. Such
coupled fluid-solid systems form a class of problems known as fluidstructure
interactions. In the present work a co-located finite volume
discretization procedure on unstructured meshes is described for
solving fluid-structure interaction type of problems. A linear elastic
solid is assumed for which the effect of the channel deformation
on the flow is neglected. Thus the governing equations for the
fluid and the solid are decoupled and are solved separately. The
procedure is validated by solving two benchmark problems, one from
fluid mechanics and another from solid mechanics. A fluid-structure
interaction problem of flow through a U-shaped channel embedded
in a plate is solved.