Abstract: Properly sized capacitor banks are connected across induction motors for several reasons including power factor correction, reducing distortions, increasing capacity, etc. Total harmonic distortion (THD) and power factor (PF) are used in such cases to quantify the improvements obtained through connection of the external capacitor banks. On the other hand, one of the methods for assessing the motor internal condition is by the use of Park-s pattern analysis. In spite of taking adequate precautionary measures, the capacitor banks may sometimes malfunction. Such a minor fault in the capacitor bank is often not apparently discernible. This may however, give rise to substantial degradation of power factor correction performance and may also damage the supply profile. The case is more severe with the fact that the Park-s pattern gets distorted due to such external capacitor faults, and can give anomalous results about motor internal fault analyses. The aim of this paper is to present simulation and hardware laboratory test results to have an understanding of the anomalies in harmonic distortion and Park-s pattern analyses in induction motors due to capacitor bank defects.
Abstract: Wrist pulse analysis for identification of health status
is found in Ancient Indian as well as Chinese literature. The preprocessing
of wrist pulse is necessary to remove outlier pulses and
fluctuations prior to the analysis of pulse pressure signal. This paper
discusses the identification of irregular pulses present in the pulse
series and intricacies associated with the extraction of time domain
pulse features. An approach of Dynamic Time Warping (DTW) has
been utilized for the identification of outlier pulses in the wrist pulse
series. The ambiguity present in the identification of pulse features is
resolved with the help of first derivative of Ensemble Average of
wrist pulse series. An algorithm for detecting tidal and dicrotic notch
in individual wrist pulse segment is proposed.
Abstract: This paper present some preliminary work on the
preparation and physicochemical caracterization of nanocomposite
MFI-alumina structures based on alumina hollow fibres. The fibers
are manufactured by a wet spinning process. α-alumina particles were
dispersed in a solution of polysulfone in NMP. The resulting slurry is
pressed through the annular gap of a spinneret into a precipitation
bath. The resulting green fibres are sintered. The mechanical strength
of the alumina hollow fibres is determined by a three-point-bending
test while the pore size is characterized by bubble-point testing. The
bending strength is in the range of 110 MPa while the average pore
size is 450 nm for an internal diameter of 1 mm and external diameter
of 1.7 mm. To characterize the MFI membranes various techniques
were used for physicochemical characterization of MFI–ceramic
hollow fibres membranes: The nitrogen adsorption, X-ray
diffractometry, scanning electron microscopy combined with X
emission microanalysis. Scanning Electron Microscopy (SEM) and
Energy Dispersive Microanalysis by the X-ray were used to observe
the morphology of the hollow fibre membranes (thickness,
infiltration into the carrier, defects, homogeneity). No surface film,
has been obtained, as observed by SEM and EDX analysis and
confirmed by high temperature variation of N2 and CO2 gas
permeances before cation exchange. Local analysis and characterise
(SEM and EDX) and overall (by ICP elemental analysis) were
conducted on two samples exchanged to determine the quantity and
distribution of the cation of cesium on the cross section fibre of the
zeolite between the cavities.
Abstract: The growing problem of youth unemployment in
Egypt after the 25th January Revolution has directed the attention of
some human resource experts towards considering remote
employment as a partial remedy for the unemployed youth instead of
the unavailable traditional jobs, a trend which will also help with the
congested offices and unsolved traffic problem in Cairo and spread
a flexible work culture, but despite of that, the main issue remains
unresolved for these organizations to deal with the system challenges.
In the past few years, in developed countries, there has been a
growing trend for many companies to shift to remote employment
instead of the traditional office employment for many reasons: due to
the growing technological advances that helped some employees do
their work from home on a part time basis, the need for achieving an
employee-s work balance in the middle of unbalanced complicated
life, top management focus on employee-s productivity rather their
time spent at work. The objective of this paper is to study and analyze
the advantages and challenges that Egypt-s labor force will be facing
in their implementation of remote or virtual employment in both
government and private organizations after the 25th January
revolution. Therefore, the research question will be: What are the
advantages and different challenges that Egyptian organizations
might face in their implementation for remote employment system
and how can they manage these challenges for the system to work
effectively? The study is divided into six main parts: the introduction,
objective and importance of the study, research problem,
methodology, experience of some countries that implemented remote
employment, advantages and challenges of implementing remote
employment in Egypt and then the conclusion which discuses the
results and recommendations of the study.
Abstract: It is very important to determine reference temperature when convective temperature because it should be used to calculate the temperature potential. This paper deals with the development of a new method that can determine heat transfer coefficient and reference free stream temperature simultaneously, based on transient heat transfer experiments with using two narrow band thermo-tropic liquid crystals (TLC's). The method is validated through error analysis in terms of the random uncertainties in the measured temperatures. It is shown how the uncertainties in heat transfer coefficient and free stream temperature can be reduced. The general method described in this paper is applicable to many heat transfer models with unknown free stream temperature.
Abstract: Renewable natural fibres such as oil palm, flax, and
pineapple leaf can be utilized to obtain new high performance
polymer materials. The reuse of waste natural fibres as reinforcement
for polymer is a sustainable option to the environment. However, due
to its high hydroxyl content of cellulose, natural fibres are
susceptible to absorb water that affects the composite mechanical
properties adversely. Research found that Nano materials such as
Nano Silica Carbide (n-SiC) and Nano Clay can be added into the
polymer composite to overcome this problem by enhancing its
mechanical properties in wet condition. The addition of Nano
material improves the tensile and wear properties, flexural stressstrain
behaviour, fracture toughness, and fracture strength of polymer
natural composites in wet and dry conditions.
Abstract: The use of wind energy for electricity generation is
growing rapidly across the world and in Portugal. However, the
geographical characteristics of the country along with the average
wind regime and with the environmental restrictions imposed to these
projects create limitations to the exploit of the onshore wind
resource. The best onshore wind spots are already committed and the
possibility of offshore wind farms in the Portuguese cost is now
being considered. This paper aims to make a contribution to the
evaluation of offshore wind power projects in Portugal. The technical
restrictions are addressed and the strategic, environmental and
financial interest of the project is analysed from the private company
and public points of view. The results suggest that additional support
schemes are required to ensure private investors interest for these
projects. Assuming an approach of direct substitution of energy
sources for electricity generation, the avoided CO2 equivalent
emissions for an offshore wind power project were quantified. Based
on the conclusions, future research is proposed to address the
environmental and social impacts of these projects.
Abstract: This study utilizes the panel vector error correction
model (PVECM) to examine the relationship among corruption,
economic growth, and income inequality experienced within ten Asian
countries over the 1995 to 2010 period. According to the empirical
results, we do not support the common perception that corruption
decreases economic growth. On the contrary, we found that corruption
increases economic growth. Meanwhile, an increase in economic
growth will cause an increase in income inequality, although the effect
is insignificant. Similarly, an increase in income inequality will cause
an increase in economic growth but a decrease in corruption, although
the effect is also insignificant.
Abstract: It is claimed that a new style of urban planning and
policy intertwined with ICT is emerging and urban planning and ICT
policy are no longer considered as separate disciplines. The
interactions between electronic spaces and urban spaces are so
complex and uncertain that confront urban planners and policy makers
with great challenges. However, the assumption about the relationship
between ICT and urban planning is mainly based on North American
and European experiences. In the light of empirical evidence from
Taipei City, this paper shows that this new type of urban planning and
policy intertwined with ICT has existed in Asian city for a decade as
well. Based on these results, this paper further reviews how the Taipei
City government implements this new type of urban ICT planning and
the validity and realism of its underlying assumptions. Finally, it also
explores the extent to which urban ICT planning could promote
positive synergies between physical and electronic developments.
Abstract: This paper presents a new high speed simulation methodology to solve the long simulation time problem of CMOS image sensor matrix. Generally, for integrating the pixel matrix in SOC and simulating the system performance, designers try to model the pixel in various modeling languages such as VHDL-AMS, SystemC or Matlab. We introduce a new alternative method based on spice model in cadence design platform to achieve accuracy and reduce simulation time. The simulation results indicate that the pixel output voltage maximum error is at 0.7812% and time consumption reduces from 2.2 days to 13 minutes achieving about 240X speed-up for the 256x256 pixel matrix.
Abstract: Dengue fever has become a major concern for health
authorities all over the world particularly in the tropical countries.
These countries, in particular are experiencing the most worrying
outbreak of dengue fever (DF) and dengue haemorrhagic fever
(DHF). The DF and DHF epidemics, thus, have become the main
causes of hospital admissions and deaths in Malaysia. This paper,
therefore, attempts to examine the environmental factors that may
influence the recent dengue outbreak. The aim of this study is twofold,
firstly is to establish a statistical model to describe the
relationship between the number of dengue cases and a range of
explanatory variables and secondly, to identify the lag operator for
explanatory variables which affect the dengue incidence the most.
The explanatory variables involved include the level of cloud cover,
percentage of relative humidity, amount of rainfall, maximum
temperature, minimum temperature and wind speed. The Poisson and
Negative Binomial regression analyses were used in this study. The
results of the analyses on the 915 observations (daily data taken from
July 2006 to Dec 2008), reveal that the climatic factors comprising of
daily temperature and wind speed were found to significantly
influence the incidence of dengue fever after 2 and 3 weeks of their
occurrences. The effect of humidity, on the other hand, appears to be
significant only after 2 weeks.
Abstract: Technical laboratories are typically considered as
highly hazardous places in the polytechnic institution when
addressing the problems of high incidences and fatality rates. In
conjunction with several topics covered in the technical curricular,
safety and health precaution should be highlighted in order to
connect to few key ideas of being safe. Therefore the assessment of
safety awareness in terms of safety and health about hazardous and
risks at laboratories is needed and has to be incorporated with
technical education and other training programmes. The purpose of
this study was to determine the efficacy of technical laboratory safety
in one of the polytechnics in northern region. The study examined
three related issues that were; the availability of safety material and
equipment, safety practice adopted by technical teachers and
administrator-s safety attitudes in enforcing safety to the students. A
model of efficacy technical laboratory was developed to test the
linear relationship between existing safety material and equipment,
teachers- safety practice and administrators- attitude in enforcing
safety and to identify which of technical laboratory safety issues was
the most pertinent factor to realize safety in technical laboratory.
This was done by analyzing survey-based data sets particularly those
obtained from samples of 210 students in the polytechnic. The
Pearson Correlation was used to measure the association between the
variables and to test the research hypotheses. The result of the study
has found that there was a significant correlation between existing
safety material and equipment, safety practice adopted by teacher
and administrator-s attitude. There was also a significant relationship
between technical laboratory safety and safety practice adopted by
teacher and between technical laboratory safety and administrator
attitude. Hence, safety practice adopted by teacher and administrator
attitude is vital in realizing technical laboratory safety.
Abstract: Space Vector Modulation (SVM) is an optimum Pulse Width Modulation (PWM) technique for an inverter used in a variable frequency drive applications. It is computationally rigorous and hence limits the inverter switching frequency. Increase in switching frequency can be achieved using Neural Network (NN) based SVM, implemented on application specific chips. This paper proposes a neural network based SVM technique for a Voltage Source Inverter (VSI). The network proposed is independent of switching frequency. Different architectures are investigated keeping the total number of neurons constant. The performance of the inverter is compared for various switching frequencies for different architectures of NN based SVM. From the results obtained, the network with minimum resource and appropriate word length is identified. The bit precision required for this application is identified. The network with 8-bit precision is implemented in the IC XCV 400 and the results are presented. The performance of NN based general purpose SVM with higher bit precision is discussed.
Abstract: We developed a GPS-based navigation device for the
blind, with audio guidance in Thai language. The device is composed
of simple and inexpensive hardware components. Its user interface is
quite simple. It determines optimal routes to various landmarks in our
university campus by using heuristic search for the next waypoints.
We tested the device and made note of its limitations and possible
extensions.
Abstract: The main objective of this paper is a comparative
investigate in enhancement of damping power system oscillation via
coordinated design of the power system stabilizer (PSS) and static
synchronous series compensator (SSSC) and static synchronous
compensator (STATCOM). The design problem of FACTS-based
stabilizers is formulated as a GA based optimization problem. In this
paper eigenvalue analysis method is used on small signal stability of
single machine infinite bus (SMIB) system installed with SSSC and
STATCOM. The generator is equipped with a PSS. The proposed
stabilizers are tested on a weakly connected power system with
different disturbances and loading conditions. This aim is to enhance
both rotor angle and power system stability. The eigenvalue analysis
and non-linear simulation results are presented to show the effects of
these FACTS-based stabilizers and reveal that SSSC exhibits the best
effectiveness on damping power system oscillation.
Abstract: This study assessed the effects of climate change on
Thai soybeans under simulation situations. Our study is focused on
temperature variability and effects on growth, yield, and genetic
changes in 2 generations of Chiang Mai 60 cultivars. In the
experiment, soybeans were exposed to 3 levels of air temperature for
8 h day-1 in an open top chamber for 2 cropping periods. Air
temperature levels in each treatment were controlled at 30-33°C (±
2.3) for LT-treatment, 33-36°C ( ± 2.4) for AT-treatment, and 36-40
°C ( ± 3.2) for HT-treatment, respectively. Positive effects of high
temperature became obvious at the maturing stage when yield
significantly increased in both cropping periods. Results in growth
indicated that shoot length at the pre-maturing stage
(V3-R3) was more positively affected by high temperature than at the
maturing stage. However, the positive effect on growth under high
temperature was not found in the 2nd cropping period. Finally, genetic
changes were examined in phenotype characteristics by the AFLPs
technique. The results showed that the high temperature factor clearly
caused genetic change in the soybeans and showed more alteration in
the 2nd cropping period.
Abstract: The National Blood Center, Thai Red Cross Society is
responsible for providing blood to hospitals all over the country.
When any hospital needs blood, it will have to send the vehicle to
pick up at the NBC. There are a lot of vehicles to pick up blood at the
NBC every day. Each vehicle is usually empty for inbound trip and a
little loaded for outbound. The NBC realized such waste or loss and
there have been the third party offered to distribute blood and charge
for fee. This paper proposes to apply the vehicle routing problem
(VRP) for estimating the fair price. The idea is tested with the real
data during seven-day period of 6 – 12 July 2010 to estimate the fair
price for transporting blood in Bangkok Metropolitan Region.
Abstract: Monoculture and mixed cultures of microalgae and
the oleaginous yeast for microbial oil productions were investigated
using sugarcane juice as carbon substrate. The monoculture of yeast
Torulaspora maleeae Y30, Torulaspora globosa YU5/2 grew faster
than that of microalgae Chlorella sp. KKU-S2. In monoculture of T.
maleeae Y30, a biomass of 8.267g/L with lipid yield of 0.920g/L
were obtained, while 8.333g/L of biomass with lipid yield of
1.141g/L were obtained for monoculture of T. globosa YU5/2. A
biomass of 1.933g/L with lipid yield of 0.052g/L was found for
monoculture of Chlorella sp. KKU-S2. The biomass concentration in
the mixed culture of the oleaginous yeast with microalgae increased
faster and was higher compared with that in the monocultures. A
biomass of 8.733g/L with lipid yield of 1.564g/L was obtained for a
mixed culture of T. maleeae Y30 with Chlorella sp. KKU-S2, while
8.010g/L of biomass with lipid yield of 2.424g/L was found for
mixed culture of T. globosa YU5/2 with Chlorella sp. KKU-S2.
Maximum cell yield coefficient (YX/S, g/L) was found of 0.323 in
monoculture of Chlorella sp. KKU-S2 but low level of both specific
yield of lipid (YP/X, g lipid/g cells) of 0.027 and volumetric lipid
production rate (QP, g/L/d) of 0.003 were observed. While, maximum
YP/X (0.303), QP (0.105) and maximum process product yield (YP/S,
0.061) were obtained in mixed culture of T. globosa YU5/2 with
Chlorella sp. KKU-S2. The results obtained from the study shows
that mixed culture of yeast with microalgae is a desirable cultivation
process for microbial oil production.
Abstract: The running logs of a process hold valuable
information about its executed activity behavior and generated activity
logic structure. Theses informative logs can be extracted, analyzed and
utilized to improve the efficiencies of the process's execution and
conduction. One of the techniques used to accomplish the process
improvement is called as process mining. To mine similar processes is
such an improvement mission in process mining. Rather than directly
mining similar processes using a single comparing coefficient or a
complicate fitness function, this paper presents a simplified heuristic
process mining algorithm with two similarity comparisons that are
able to relatively conform the activity logic sequences (traces) of
mining processes with those of a normalized (regularized) one. The
relative process conformance is to find which of the mining processes
match the required activity sequences and relationships, further for
necessary and sufficient applications of the mined processes to process
improvements. One similarity presented is defined by the relationships
in terms of the number of similar activity sequences existing in
different processes; another similarity expresses the degree of the
similar (identical) activity sequences among the conforming processes.
Since these two similarities are with respect to certain typical behavior
(activity sequences) occurred in an entire process, the common
problems, such as the inappropriateness of an absolute comparison and
the incapability of an intrinsic information elicitation, which are often
appeared in other process conforming techniques, can be solved by the
relative process comparison presented in this paper. To demonstrate
the potentiality of the proposed algorithm, a numerical example is
illustrated.
Abstract: Construction site safety in China has aroused
comprehensive concern all over the world. It is imperative to
investigate the main causes of poor construction site safety. This paper
divides all the causes into four aspects, namely the factors of workers,
object, environment and management and sets up the accident causes
element system based on Delphi Method. This is followed by the
application of structural equation modeling to examine the importance
of each aspect of causes from the standpoints of different roles related
to the construction respectively. The results indicate that all the four
aspects of factors are in need of improvement, and different roles have
different ideas considering the priority of those factors. The paper has
instructive significance for the practitioners to take measures to
improve construction site safety in China accordingly.