Abstract: Microscopic emission and fuel consumption models
have been widely recognized as an effective method to quantify real
traffic emission and energy consumption when they are applied with
microscopic traffic simulation models. This paper presents a
framework for developing the Microscopic Emission (HC, CO, NOx,
and CO2) and Fuel consumption (MEF) models for light-duty
vehicles. The variable of composite acceleration is introduced into
the MEF model with the purpose of capturing the effects of historical
accelerations interacting with current speed on emission and fuel
consumption. The MEF model is calibrated by multivariate
least-squares method for two types of light-duty vehicle using
on-board data collected in Beijing, China by a Portable Emission
Measurement System (PEMS). The instantaneous validation results
shows the MEF model performs better with lower Mean Absolute
Percentage Error (MAPE) compared to other two models. Moreover,
the aggregate validation results tells the MEF model produces
reasonable estimations compared to actual measurements with
prediction errors within 12%, 10%, 19%, and 9% for HC, CO, NOx
emissions and fuel consumption, respectively.
Abstract: Particle damping is a technique to reduce the
structural vibrations by means of placing small metallic particles
inside a cavity that is attached to the structure at location of high
vibration amplitudes. In this paper, we have presented an analytical
model to simulate the particle damping of two dimensional transient
vibrations in structure operating under high centrifugal loads. The
simulation results show that this technique remains effective as long
as the ratio of the dynamic acceleration of the structure to the applied
centrifugal load is more than 0.1. Particle damping increases with the
increase of particle to structure mass ratio. However, unlike to the
case of particle damping in the absence of centrifugal loads where
the damping efficiency strongly depends upon the size of the cavity,
here this dependence becomes very weak. Despite the simplicity of
the model, the simulation results are considerably in good agreement
with the very scarce experimental data available in the literature for
particle damping under centrifugal loads.
Abstract: This paper has, as its point of departure, the foundational
axiomatic theory of E. De Giorgi (1996, Scuola Normale
Superiore di Pisa, Preprints di Matematica 26, 1), based on two
primitive notions of quality and relation. With the introduction of
a unary relation, we develop a system totally based on the sole
primitive notion of relation. Such a modification enables a definition
of the concept of dynamic unary relation. In this way we construct a
simple language capable to express other well known theories such
as Robinson-s arithmetic or a piece of a theory of concatenation. A
key role in this system plays an abstract relation designated by “( )",
which can be interpreted in different ways, but in this paper we will
focus on the case when we can perform computations and obtain
results.
Abstract: Mostly transforms are used for speech data
compressions which are lossy algorithms. Such algorithms are
tolerable for speech data compression since the loss in quality is not
perceived by the human ear. However the vector quantization (VQ)
has a potential to give more data compression maintaining the same
quality. In this paper we propose speech data compression algorithm
using vector quantization technique. We have used VQ algorithms
LBG, KPE and FCG. The results table shows computational
complexity of these three algorithms. Here we have introduced a new
performance parameter Average Fractional Change in Speech
Sample (AFCSS). Our FCG algorithm gives far better performance
considering mean absolute error, AFCSS and complexity as
compared to others.
Abstract: Swietenia mahagoni have been used in traditional
medicine for treatment of different diseases. Present study was
performed to evaluate anti-ulcerogenic activity of ethanol seed
extract against ethanol induced gastric mucosal injury in rats. Six
groups of rats were orally pre-treated respectively with
carboxymethyl cellulose, omeprazole 20 mg/kg, 50, 100, 200 and 400
mg/kg plant extract one hour before oral administration of absolute
ethanol to generate gastric mucosal injury. After additional hour, rats
were sacrificed and ulcer areas of gastric walls were determined.
Grossly, carboxymethyl cellulose group exhibited severe mucosal
injury, whereas pre-treatment with plant extract exhibited significant
protection of gastric mucosa. Histology, carboxymethyl cellulose
group exhibited severe damage of gastric mucosa; edema and
leucocytes infiltration of sub mucosa compared to plant extract which
showed gastric protection. Acute toxicity study did not manifest any
toxicological signs in rats. Conclusions, results suggest that S.
mahagoni promotes ulcer protection as ascertained grossly and
histologically.
Abstract: In this paper two different Antilock braking system (ABS) are simulated and compared. One is the ordinary hydraulic ABS system which we call it ABS and the other is Electromagnetic Antilock braking system which is called (EMABS) the basis of performance of an EMABS is based upon Electromagnetic force. In this system there is no need to use servo hydraulic booster which are used in ABS system. In EMABS to generate the desired force we have use a magnetic relay which works with an input voltage through an air gap (g). The generated force will be amplified by the relay arm, and is applied to the brake shoes and thus the braking torque is generated. The braking torque is proportional to the applied electrical voltage E. to adjust the braking torque it is only necessary to regulate the electrical voltage E which is very faster and has a much smaller time constant T than the ABS system. The simulations of these two different ABS systems are done with MATLAB/SIMULINK software and the superiority of the EMABS has been shown.
Abstract: This work presents a theoretical investigation of the
simultaneous absorption of CO2 and H2S into aqueous solutions of
MDEA and DEA. In this process the acid components react
with the basic alkanolamine solution via an exothermic,
reversible reaction in a gas/liquid absorber. The use of amine
solvents for gas sweetening has been investigated using
process simulation programs called HYSYS and ASPEN. We
use Electrolyte NRTL and Amine Package and Amines
(experimental) equation of state. The effects of temperature and
circulation rate and amine concentration and packed column and
murphree efficiency on the rate of absorption were studied.
When lean amine flow and concentration increase, CO2 and H2S
absorption increase too. With the improvement of inlet amine
temperature in absorber, CO2 and H2S penetrate to upper stages of
absorber and absorption of acid gases in absorber decreases. The CO2
concentration in the clean gas can be greatly influenced by the
packing height, whereas for the H2S concentration in the clean gas the
packing height plays a minor role. HYSYS software can not
estimate murphree efficiency correctly and it applies the same
contributions in all diagrams for HYSYS software. By
improvement in murphree efficiency, maximum temperature
of absorber decrease and the location of reaction transfer to the
stages of bottoms absorber and the absorption of acid gases
increase.
Abstract: This paper proposes the use of metrics in design space exploration that highlight where in the structure of the model and at what point in the behaviour, prevention is needed against transient faults. Previous approaches to tackle transient faults focused on recovery after detection. Almost no research has been directed towards preventive measures. But in real-time systems, hard deadlines are performance requirements that absolutely must be met and a missed deadline constitutes an erroneous action and a possible system failure. This paper proposes the use of metrics to assess the system design to flag where transient faults may have significant impact. These tools then allow the design to be changed to minimize that impact, and they also flag where particular design techniques – such as coding of communications or memories – need to be applied in later stages of design.
Abstract: Integrins are a large family of multidomain α/β cell
signaling receptors. Some integrins contain an additional inserted I
domain, whose earliest expression appears to be with the chordates,
since they are observed in the urochordates Ciona intestinalis (vase
tunicate) and Halocynthia roretzi (sea pineapple), but not in integrins
of earlier diverging species. The domain-s presence is viewed as a
hallmark of integrins of higher metazoans, however in vertebrates,
there are clearly three structurally-different classes: integrins without
I domains, and two groups of integrins with I domains but separable
by the presence or absence of an additional αC helix. For example,
the αI domains in collagen-binding integrins from Osteichthyes
(bony fish) and all higher vertebrates contain the specific αC helix,
whereas the αI domains in non-collagen binding integrins from
vertebrates and the αI domains from earlier diverging urochordate
integrins, i.e. tunicates, do not. Unfortunately, within the early
chordates, there is an evolutionary gap due to extinctions between the
tunicates and cartilaginous fish. This, coupled with a knowledge gap
due to the lack of complete genomic data from surviving species,
means that the origin of collagen-binding αC-containing αI domains
remains unknown. Here, we analyzed two available genomes from
Callorhinchus milii (ghost shark/elephant shark; Chondrichthyes –
cartilaginous fish) and Petromyzon marinus (sea lamprey;
Agnathostomata), and several available Expression Sequence Tags
from two Chondrichthyes species: Raja erinacea (little skate) and
Squalus acanthias (dogfish shark); and Eptatretus burgeri (inshore
hagfish; Agnathostomata), which evolutionary reside between the
urochordates and osteichthyes. In P. marinus, we observed several
fragments coding for the αC-containing αI domain, allowing us to
shed more light on the evolution of the collagen-binding integrins.
Abstract: This paper investigates the effects of lubrication on
the quantity of heat emission of two spur gear. System with and
without lubrication effected on the quantity of heat induced on the
gear box (oil - bearings – gears). Both of lubrication and speed of
motor are affected on the performance of gears. Research investigated
the lubrication on the system with and without loading as well as the
wear of gears and bearing's conditions. Gear box investigated
includes the motor, pump, two spur gears, two shafts; speed change
used pulleys and belts. Load used equal one weight ones of gear.
Lubrication mechanism used jet system (upper and lower jet). Gear
box we used system of jet lubrication is perpendicular direction of
the contact line between two teeth. Results appeared in this work that
the lubrication is the vital parameter which is affected on the
performance and durability of gears and bearings. In macroscopic
observation, we noted that damage of bearings happened during the
absence of lubrication as well as abrasive of wear of teeth. Higher
speed of motor without lubrication increased the noise, but in the
presence of lubrication was decreased.
Abstract: This work concerns on experimentally investigation
of surfactant flooding in fractured porous media. In this study a series
of water and surfactant injection processes were performed on
micromodels initially saturated with a heavy crude oil. Eight
fractured glass micromodels were used to illustrate effects of
surfactant types and concentrations on oil recovery efficiency in
presence of fractures with different properties i.e. fracture
orientation, length and number of fractures. Two different
surfactants with different concentrations were tested. The results
showed that surfactant flooding would be more efficient by using
SDS surfactant aqueous solution and also by locating injection well
in a proper position respect to fracture properties. This study
demonstrates different physical and chemical conditions that affect
the efficiency of this method of enhanced oil recovery.
Abstract: This paper investigates the impact of the hand-hold
positions on both antenna performance and the specific absorption
rate (SAR) induced in the user-s head. A cellular handset with
external antenna operating at GSM-900 frequency is modeled and
simulated using a finite difference time-domain (FDTD)-based
platform SEMCAD-X. A specific anthropomorphic mannequin
(SAM) is adopted to simulate the user-s head, whereas a semirealistic
CAD-model of three-tissues is designed to simulate the
user-s hand. The results show that in case of the handset in hand close
to head at different positions; the antenna total efficiency gets
reduced to (14.5% - 5.9%) at cheek-position and to (27.5% to 11.8%)
at tilt-position. The peak averaged SAR1g values in head close to
handset without hand, are 4.67 W/Kg and 2.66 W/Kg at cheek and
tilt-position, respectively. Due to the presence of hand, the SAR1g in
head gets reduced to (3.67-3.31 W/Kg) at cheek-position and to
(1.84-1.64 W/Kg) at tilt-position, depending on the hand-hold
position.
Abstract: The fast growth in complexity coupled with requests for shorter development periods for embedded systems are bringing demands towards a more effective, i.e. higher-abstract, design process for hardaware/software integrated design. In Software Engineering area, Model Driven Architecture (MDA) and Executable UML (xUML) has been accepted to bring further improvement in software design. This paper constructs MDA and xUML stepwise transformations from an abstract specification model to a more concrete implementation model using the refactoring technique for hardaware/software integrated design. This approach provides clear and structured models which enables quick exploration and synthesis, and early stage verification.
Abstract: Hybrid photovoltaic thermal (PV/T) solar system comprises a solar collector which is disposed on photovoltaic solar cells. The disadvantage of a conventional photovoltaic cell is that its performance decreases as the temperature increases. Indeed, part of the solar radiation is converted into electricity and is dissipated as heat, increasing the temperature of the photovoltaic cell with respect to the ambient temperature. The objective of this work is to study experimentally and implement a hybrid prototype to evaluate electrical and thermal performance. In this paper, an experimental study of two new configurations of hybrid collectors is exposed. The results are given and interpreted. The two configurations of absorber studied are a new combination with tubes and galvanized tank, the other is a tubes and sheet.
Abstract: The ability of agricultural and decorative plants to
absorb and detoxify TNT and RDX has been studied. All tested 8
plants, grown hydroponically, were able to absorb these explosives
from water solutions: Alfalfa > Soybean > Chickpea> Chikling vetch
>Ryegrass > Mung bean> China bean > Maize. Differently from
TNT, RDX did not exhibit negative influence on seed germination
and plant growth. Moreover, some plants, exposed to RDX
containing solution were increased in their biomass by 20%. Study of
the fate of absorbed [1-14ðí]-TNT revealed the label distribution in
low and high-molecular mass compounds, both in roots and above
ground parts of plants, prevailing in the later. Content of 14ðí in lowmolecular
compounds in plant roots are much higher than in above
ground parts. On the contrary, high-molecular compounds are more
intensively labeled in aboveground parts of soybean. Most part (up to
70%) of metabolites of TNT, formed either by enzymatic reduction
or oxidation, is found in high molecular insoluble conjugates.
Activation of enzymes, responsible for reduction, oxidation and
conjugation of TNT, such as nitroreductase, peroxidase,
phenoloxidase and glutathione S-transferase has been demonstrated.
Among these enzymes, only nitroreductase was shown to be induced
in alfalfa, exposed to RDX. The increase in malate dehydrogenase
activities in plants, exposed to both explosives, indicates
intensification of Tricarboxylic Acid Cycle, that generates reduced
equivalents of NAD(P)H, necessary for functioning of the
nitroreductase. The hypothetic scheme of TNT metabolism in plants
is proposed.
Abstract: Deoxyribonucleic Acid or DNA computing has
emerged as an interdisciplinary field that draws together chemistry,
molecular biology, computer science and mathematics. Thus, in this
paper, the possibility of DNA-based computing to solve an absolute
1-center problem by molecular manipulations is presented. This is
truly the first attempt to solve such a problem by DNA-based
computing approach. Since, part of the procedures involve with
shortest path computation, research works on DNA computing for
shortest path Traveling Salesman Problem, in short, TSP are reviewed.
These approaches are studied and only the appropriate one is adapted
in designing the computation procedures. This DNA-based
computation is designed in such a way that every path is encoded by
oligonucleotides and the path-s length is directly proportional to the
length of oligonucleotides. Using these properties, gel electrophoresis
is performed in order to separate the respective DNA molecules
according to their length. One expectation arise from this paper is that
it is possible to verify the instance absolute 1-center problem using
DNA computing by laboratory experiments.
Abstract: As is needless to say; a majority of accidents, which occur, are due to drunk driving. As such, there is no effective mechanism to prevent this. Here we have designed an integrated system for the same purpose. Alcohol content in the driver-s body is detected by means of an infrared breath analyzer placed at the steering wheel. An infrared cell directs infrared energy through the sample and any unabsorbed energy at the other side is detected. The higher the concentration of ethanol, the more infrared absorption occurs (in much the same way that a sunglass lens absorbs visible light, alcohol absorbs infrared light). Thus the alcohol level of the driver is continuously monitored and calibrated on a scale. When it exceeds a particular limit the fuel supply is cutoff. If the device is removed also, the fuel supply will be automatically cut off or an alarm is sounded depending upon the requirement. This does not happen abruptly and special indicators are fixed at the back to avoid inconvenience to other drivers using the highway signals. Frame work for integration of sensors and control module in a scalable multi-agent system is provided .A SMS which contains the current GPS location of the vehicle is sent via a GSM module to the police control room to alert the police. The system is foolproof and the driver cannot tamper with it easily. Thus it provides an effective and cost effective solution for the problem of drunk driving in vehicles.
Abstract: Social ideology, cultural values and principles shaping environment are inferred by environment and structural characteristics of construction site. In other words, this inference manifestation also indicates ideology and culture of its foundation and also applies its principles and values and somehow plays an important role in Cultural Revolution. All human behaviors and artifacts are affected and being influenced by culture. Culture is not abstract concept, it is a spiritual domain that an individual and society grow and develop in it. Social behaviors are affected by environmental comprehension, so the architecture work influences on its audience and it is the environment that fosters social behaviors. Indeed, sustainable architecture should be considered as background of culture for establishing optimal sustainable culture. Since unidentified architecture roots in cultural non identity and abnormalities, so the society possesses identity characteristics and life and as a consequence, the society and architecture are changed by transformation of life style. This article aims to investigate the interaction of architecture, society, environment and sustainable architecture formation in its cultural basis and analyzes the results approaching behavior and sustainable culture in recent era.
Abstract: Headphones and earphones have many extremely small
holes or narrow slits; they use sound-absorbing or porous material (i.e.,
dampers) to suppress vibratory system resonance. The air viscosity in
these acoustic paths greatly affects the acoustic properties. Simulation
analyses such as the finite element method (FEM) therefore require
knowledge of the material properties of sound-absorbing or porous
materials, such as the characteristic impedance and propagation
constant. The transfer function method using acoustic tubes is a widely
known measuring method, but there is no literature on taking
measurements up to the audible range. To measure the acoustic
properties at high-range frequencies, the acoustic tubes that form the
measuring device need to be narrowed, and the distance between the
two microphones needs to be reduced. However, when the tubes are
narrowed, the characteristic impedance drops below the air impedance.
In this study, we considered the effect of air viscosity in an acoustical
tube, introduced a theoretical formula for this effect in the form of
complex density and complex sonic velocity, and verified the
theoretical formula. We also conducted an experiment and observed
the effect from air viscosity in the actual measurements.
Abstract: The state and stability of hemoglobin adsorbed on the
glass surface was investigated using slab optical waveguide (SOWG)
spectroscopy. The peak position of the absorption band of hemoglobin
adsorbed on the glass surface was same as that of the hemoglobin in
solution. This result suggests that no significant denaturation occurred
by adsorption. The adsorption of hemoglobin is relatively strong that
the hemoglobin molecules even remained adsorbed after rinsing the
cell with buffer solution. The peak shift caused by the reduction of
adsorbed hemoglobin was also observed.