Abstract: The aim of this study is to develop mathematical
relationships for the performance parameter brake thermal efficiency
(BTE) and emission parameter nitrogen oxides (NOx) for the various
esters of vegetable oils used as CI engine fuel. The BTE is an
important performance parameter defining the ability of engine to
utilize the energy supplied and power developed similarly it is
indication of efficiency of fuels used. The esters of cottonseed oil,
soybean oil, jatropha oil and hingan oil are prepared using
transesterification process and characterized for their physical and
main fuel properties including viscosity, density, flash point and
higher heating value using standard test methods. These esters are
tried as CI engine fuel to analyze the performance and emission
parameters in comparison to diesel. The results of the study indicate
that esters as a fuel does not differ greatly with that of diesel in
properties. The CI engine performance with esters as fuel is in line
with the diesel where as the emission parameters are reduced with the
use of esters.
The correlation developed between BTE and brake power(BP),
gross calorific value(CV), air-fuel ratio(A/F), heat carried away by
cooling water(HCW). Another equation is developed between the
NOx emission and CO, HC, smoke density (SD), exhaust gas
temperature (EGT). The equations are verified by comparing the
observed and calculated values which gives the coefficient of
correlation of 0.99 and 0.96 for the BTE and NOx equations
respectively.
Abstract: In this paper, we develop quartic nonpolynomial
spline method for the numerical solution of third order two point
boundary value problems. It is shown that the new method gives
approximations, which are better than those produced by other spline
methods. Convergence analysis of the method is discussed through
standard procedures. Two numerical examples are given to illustrate
the applicability and efficiency of the novel method.
Abstract: In this work we study the effect of several covariates X on a censored response variable T with unknown probability distribution. In this context, most of the studies in the literature can be located in two possible general classes of regression models: models that study the effect the covariates have on the hazard function; and models that study the effect the covariates have on the censored response variable. Proposals in this paper are in the second class of models and, more specifically, on least squares based model approach. Thus, using the bootstrap estimate of the bias, we try to improve the estimation of the regression parameters by reducing their bias, for small sample sizes. Simulation results presented in the paper show that, for reasonable sample sizes and censoring levels, the bias is always smaller for the new proposals.
Abstract: As a vital activity for companies, new product
development (NPD) is also a very risky process due to the high
uncertainty degree encountered at every development stage and the
inevitable dependence on how previous steps are successfully
accomplished. Hence, there is an apparent need to evaluate new
product initiatives systematically and make accurate decisions under
uncertainty. Another major concern is the time pressure to launch a
significant number of new products to preserve and increase the
competitive power of the company. In this work, we propose an
integrated decision-making framework based on neural networks and
fuzzy logic to make appropriate decisions and accelerate the
evaluation process. We are especially interested in the two initial
stages where new product ideas are selected (go/no go decision) and
the implementation order of the corresponding projects are
determined. We show that this two-staged intelligent approach allows
practitioners to roughly and quickly separate good and bad product
ideas by making use of previous experiences, and then, analyze a
more shortened list rigorously.
Abstract: Pyritisation halos are identified in weathering crusts and unconsolidated formations at five locations within large fault structure of the Urals’ eastern slope. Electron microscopy reveals the presence of inclusions and growths on pyrite faces – normally on cubic pyrite with striations, or combinations of cubes and other forms. Following neogenesis types are established: native elements and intermetallic compounds (including gold and silver), halogenides, sulphides, sulfosalts, tellurides, sulphotellurides,
selenides, tungstates, sulphates, phosphates, carbon-based substances. Direct relationship is noted between amount and diversity of such mineral phases, and proximity to and scale of ore-grade mineralization. Gold and silver, both in native form and within tellurides, presence of lead (galena, native lead), native tungsten, and, possibly, molybdenite and sulfosalts can indicate gold-bearing formations. First find of native tungsten in the Urals is for the first time – in crystallised and druse-like form. Link is suggested between unusual mineralization and “reducing” hydrothermal fluids from deep-seated faults at later stages of Urals’ reactivation.
Abstract: Coal tar is a liquid by-product of the process of coal
gasification and carbonation. This liquid oil mixture contains various
kinds of useful compounds such as phenol, o-cresol, and p-cresol.
These compounds are widely used as raw material for insecticides,
dyes, medicines, perfumes, coloring matters, and many others.
This research needed to be done that given the optimum conditions
for the separation of phenol, o-cresol, and p-cresol from the coal tar
by solvent extraction process. The aim of the present work was to
study the effect of two kinds of aqueous were used as solvents:
methanol and acetone solutions, the effect of temperature (298, 306,
and 313K) and mixing (30, 35, and 40rpm) for the separation of
phenol, o-cresol, and p-cresol from coal tar by solvent extraction.
Results indicated that phenol, o-cresol, and p-cresol in coal tar
were selectivity extracted into the solvent phase and these
components could be separated by solvent extraction. The aqueous
solution of methanol, mass ratio of solvent to feed, Eo/Ro=1,
extraction temperature 306K and mixing 35 rpm were the most
efficient for extraction of phenol, o-cresol, and p-cresol from coal tar.
Abstract: We integrate TiN/Ni/HfO2/Si RRAM cell with a
vertical gate-all-around (GAA) nanowire transistor to achieve
compact 4F2 footprint in a 1T1R configuration. The tip of the Si
nanowire (source of the transistor) serves as bottom electrode of the
memory cell. Fabricated devices with nanowire diameter ~ 50nm
demonstrate ultra-low current/power switching; unipolar switching
with 10μA/30μW SET and 20μA/30μW RESET and bipolar switching
with 20nA/85nW SET and 0.2nA/0.7nW RESET. Further, the
switching current is found to scale with nanowire diameter making the
architecture promising for future scaling.
Abstract: The significant effects of the interactions between the
system boundaries and the near wall molecules in miniaturized
gaseous devices lead to the formation of the Knudsen layer in which
the Navier-Stokes-Fourier (NSF) equations fail to predict the correct
associated phenomena. In this paper, the well-known lattice
Boltzmann method (LBM) is employed to simulate the fluid flow and
heat transfer processes in rarefied gaseous micro media. Persuaded
by the problematic deficiency of the LBM in capturing the Knudsen
layer phenomena, present study tends to concentrate on the effective
molecular mean free path concept the main essence of which is to
compensate the incapability of this mesoscopic method in dealing
with the momentum and energy transport within the above mentioned
kinetic boundary layer. The results show qualitative and quantitative
accuracy comparable to the solutions of the linearized Boltzmann
equation or the DSMC data for the Knudsen numbers of O (1) .
Abstract: The “PYRAMIDS" Block Cipher is a symmetric encryption algorithm of a 64, 128, 256-bit length, that accepts a variable key length of 128, 192, 256 bits. The algorithm is an iterated cipher consisting of repeated applications of a simple round transformation with different operations and different sequence in each round. The algorithm was previously software implemented in Cµ code. In this paper, a hardware implementation of the algorithm, using Field Programmable Gate Arrays (FPGA), is presented. In this work, we discuss the algorithm, the implemented micro-architecture, and the simulation and implementation results. Moreover, we present a detailed comparison with other implemented standard algorithms. In addition, we include the floor plan as well as the circuit diagrams of the various micro-architecture modules.
Abstract: This study reports results of a meta-analytic path analysis e-learning Acceptance Model with k = 27 studies, Databases searched included Information Sciences Institute (ISI) website. Variables recorded included perceived usefulness, perceived ease of use, attitude toward behavior, and behavioral intention to use e-learning. A correlation matrix of these variables was derived from meta-analytic data and then analyzed by using structural path analysis to test the fitness of the e-learning acceptance model to the observed aggregated data. Results showed the revised hypothesized model to be a reasonable, good fit to aggregated data. Furthermore, discussions and implications are given in this article.
Abstract: This paper details a new concept of using compressed air as a potential zero pollution power source for motorbikes. In place of an internal combustion engine, the motorbike is equipped with an air turbine transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor diameters, casing diameters and ratio of rotor to casing diameters of the turbine have been considered and analyzed. It is concluded that the work output is found optimum for some typical values of rotor / casing diameter ratios. In this study, the maximum power works out to 3.825 kW (5.20 HP) for casing diameter of 200 mm and rotor to casing diameter ratio of 0.65 to 0.60 which is sufficient to run motorbike.
Abstract: The present study was conducted to observe the effect
of Plantago psyllium on blood glucose and cholesterol levels in
normal and alloxan induced diabetic rats. To investigate the effect of
Plantago psyllium 40 rats were included in this study divided into
four groups of ten rats in each group. One group A was normal,
second group B was diabetic, third group C was non diabetic and
hypercholesterolemic and fourth group D was diabetic and
hypercholesterolemic. Two groups B and D were made diabetic by
intraperitonial injection of alloxan dissolved in 1mL distilled water at
a dose of 125mg/Kg of body weight. Two groups C and D were
made hypercholesterolemic by oral administration of powder
cholesterol (1g/Kg of body weight). The blood samples from all the
rats were collected from coccygial vein on 1st day, then on 21st and
42nd day respectively. All the samples were analyzed for blood
glucose and cholesterol level by using enzymatic kits. The blood
glucose and cholesterol levels of treated groups of rats showed
significant reduction after 7 weeks of treatment with Plantago
psyllium. By statistical analysis of results it was found that Plantago
psyllium has anti-diabetic and hypocholesterolemic activity in
diabetic and hypercholesterolemic albino rats.
Abstract: This paper proposes a method which reduces power consumption in single-error correcting, double error-detecting checker circuits that perform memory error correction code. Power is minimized with little or no impact on area and delay, using the degrees of freedom in selecting the parity check matrix of the error correcting codes. The genetic algorithm is employed to solve the non linear power optimization problem. The method is applied to two commonly used SEC-DED codes: standard Hamming and odd column weight Hsiao codes. Experiments were performed to show the performance of the proposed method.
Abstract: The electrical interaction between two axisymmetric
spheroidal particles in an electrolyte solution is examined numerically.
A Galerkin finite element method combined with a Newton-Raphson
iteration scheme is proposed to evaluate the spatial variation in the
electrical potential, and the result obtained used to estimate the
interaction energy between two particles. We show that if the surface
charge density is fixed, the potential gradient is larger at a point, which
has a larger curvature, and if surface potential is fixed, surface charge
density is proportional to the curvature. Also, if the total interaction
energy against closest surface-to-surface curve exhibits a primary
maximum, the maximum follows the order (oblate-oblate) >
(sphere-sphere)>(oblate-prolate)>(prolate-prolate), and if the curve
has a secondary minimum, the absolute value of the minimum follows
the same order.
Abstract: The purposes of this study are 1) to identify
learning styles of university students in Bangkok, and 2) to study
the frequency of the relevant instructional context of the identified
learning styles. Learning Styles employed in this study are those of
Honey and Mumford, which include 1) Reflectors, 2) Theorists, 3)
Pragmatists, and 4) Activists. The population comprises 1383
students and 5 lecturers. Research tools are 2 questionnaires – one
used for identifying students- learning styles, and the other used for
identifying the frequency of the relevant instructional context of
the identified learning styles.
The research findings reveal that 32.30 percent - are Activists,
while 28.10 percent are Theorists, 20.10 are Reflectors, and 19.50
are Pragmatists. In terms of the relevant instructional context of the
identified 4 learning styles, it is found that the frequency level of
the instructional context is totally in high level. Moreover, 2 lists of
the context being conducted most frequently are 'Lead'in activity
to review background knowledge,- and 'Information retrieval
report.' And these two activities serve the learning styles of
theorists and activists. It is, therefore, suggested that more
instructional context supporting the activists, the majority of the
population, learning best by doing, as well as emotional learning
situation should be added.
Abstract: A hybrid learning automata-genetic algorithm (HLGA) is proposed to solve QoS routing optimization problem of next generation networks. The algorithm complements the advantages of the learning Automato Algorithm(LA) and Genetic Algorithm(GA). It firstly uses the good global search capability of LA to generate initial population needed by GA, then it uses GA to improve the Quality of Service(QoS) and acquiring the optimization tree through new algorithms for crossover and mutation operators which are an NP-Complete problem. In the proposed algorithm, the connectivity matrix of edges is used for genotype representation. Some novel heuristics are also proposed for mutation, crossover, and creation of random individuals. We evaluate the performance and efficiency of the proposed HLGA-based algorithm in comparison with other existing heuristic and GA-based algorithms by the result of simulation. Simulation results demonstrate that this paper proposed algorithm not only has the fast calculating speed and high accuracy but also can improve the efficiency in Next Generation Networks QoS routing. The proposed algorithm has overcome all of the previous algorithms in the literature.
Abstract: The main criteria of designing in the most hydraulic
constructions essentially are based on runoff or discharge of water. Two of those important criteria are runoff and return period. Mostly,
these measures are calculated or estimated by stochastic data.
Another feature in hydrological data is their impreciseness.
Therefore, in order to deal with uncertainty and impreciseness, based
on Buckley-s estimation method, a new fuzzy method of evaluating hydrological measures are developed. The method introduces
triangular shape fuzzy numbers for different measures in which both
of the uncertainty and impreciseness concepts are considered. Besides, since another important consideration in most of the
hydrological studies is comparison of a measure during different
months or years, a new fuzzy method which is consistent with special form of proposed fuzzy numbers, is also developed. Finally, to
illustrate the methods more explicitly, the two algorithms are tested on one simple example and a real case study.
Abstract: The following study aims to outline, whether the
perceptions of entrepreneurs about their entrepreneurial activities and
the underlying meanings of their activities are universal or whether
they vary systematically across cultures. In contrast to previous
studies, the phenomenographical approach and the resulting findings
of this study provide new insights into what constitutes
entrepreneurship by drawing an inference from the perceptions of
entrepreneurs in the United States and in Germany. Culture is shown
to have an important impact on entrepreneurship, since the
underlying meanings of entrepreneurship vary significantly among
the two sample groups. Furthermore, the study sheds more light on
the culturally contingent 'why' of entrepreneurship by looking at the
internal motivations of individuals instead of exclusively focusing on
character traits or external influences of the respective economic
environments.
Abstract: This study uses simulated meta-analysis to assess the effects of publication bias on meta-analysis estimates and to evaluate the efficacy of the trim and fill method in adjusting for these biases. The estimated effect sizes and the standard error were evaluated in terms of the statistical bias and the coverage probability. The results demonstrate that if publication bias is not adjusted it could lead to up to 40% bias in the treatment effect estimates. Utilization of the trim and fill method could reduce the bias in the overall estimate by more than half. The method is optimum in presence of moderate underlying bias but has minimal effects in presence of low and severe publication bias. Additionally, the trim and fill method improves the coverage probability by more than half when subjected to the same level of publication bias as those of the unadjusted data. The method however tends to produce false positive results and will incorrectly adjust the data for publication bias up to 45 % of the time. Nonetheless, the bias introduced into the estimates due to this adjustment is minimal
Abstract: Today, people are more interested in the foods
beneficial on their health. However, there are still lacks of accurate
knowledge in the field of biological properties, functional properties,
including the application of legume in foods. This study focused on
antioxidant activity of soybean (SB) and fermented soybean (FSB)
crude extracts evaluating to have more information in fortification SB
and FSB crude extracts in food products and/or dietary supplement.
SB and FSB crude extracts were prepared by infusion with water and
ethanol. The antioxidant activity of crude extracts was studied with
DPPH and ABTS assay including commercial standard. From both
DPPH and ABTS assay, the antioxidant activity of SB and FSB water
crude extract showed higher antioxidant activity than ethanol crude
extract, and FSB crude extract showed higher antioxidant activity
than SB crude extract. In DPPH assay, BHT and vitamin C showed
IC50 values at 0.241, 0.039 mg/ml, in ABTS assay. In addition,
Trolox showed IC50 at 0.058 mg/ml respectively. FSB water crude
extract showed high antioxidant activity. Finally, the functional
properties study of both water and ethanol crude extracts should be
done for beneficial in application of these extracts in food products
and dietary supplement in the near future.