Abstract: In this paper, a mathematical model is proposed to
estimate the dropping probabilities of cellular wireless networks by
queuing handoff instead of reserving guard channels. Usually, prioritized
handling of handoff calls is done with the help of guard channel
reservation. To evaluate the proposed model, gamma inter-arrival and
general service time distributions have been considered. Prevention of
some of the attempted calls from reaching to the switching center due
to electromagnetic propagation failure or whimsical user behaviour
(missed call, prepaid balance etc.), make the inter-arrival time of
the input traffic to follow gamma distribution. The performance is
evaluated and compared with that of guard channel scheme.
Abstract: In this paper we introduce three watermarking methods that can be used to count the number of times that a user has played some content. The proposed methods are tested with audio content in our experimental system using the most common signal processing attacks. The test results show that the watermarking methods used enable the watermark to be extracted under the most common attacks with a low bit error rate.
Abstract: In the present study, position estimation of switched reluctance motor (SRM) has been achieved on the basis of the artificial neural networks (ANNs). The ANNs can estimate the rotor position without using an extra rotor position sensor by measuring the phase flux linkages and phase currents. Flux linkage-phase current-rotor position data set and supervised backpropagation learning algorithm are used in training of the ANN based position estimator. A 4-phase SRM have been used to verify the accuracy and feasibility of the proposed position estimator. Simulation results show that the proposed position estimator gives precise and accurate position estimations for both under the low and high level reference speeds of the SRM
Abstract: This paper proposes an efficient lattice-reduction-aided
detection (LRD) scheme to improve the detection performance of
MIMO-OFDM system. In this proposed scheme, V candidate symbols
are considered at the first layer, and V probable streams are
detected with LRD scheme according to the first detected V candidate
symbols. Then, the most probable stream is selected through a ML
test. Since the proposed scheme can more accurately detect initial
symbol and can reduce transmission of error to rest symbols, the
proposed scheme shows more improved performance than conventional
LRD with very low complexity.
Abstract: We demonstrate through a sample application, Ebanking,
that the Web Service Modelling Language Ontology component
can be used as a very powerful object-oriented database design
language with logic capabilities. Its conceptual syntax allows the
definition of class hierarchies, and logic syntax allows the definition
of constraints in the database. Relations, which are available for
modelling relations of three or more concepts, can be connected to
logical expressions, allowing the implicit specification of database
content. Using a reasoning tool, logic queries can also be made
against the database in simulation mode.
Abstract: The recurring decimal of rural and urban poverty in
Nigeria, resulting from lack of sustainable livelihood activities by
the people due to non-diversification of the economy, necessitated
this study. One hundred snail farmers were randomly selected in
Akure North and Akure South Local Government areas of Ondo
State, Southwest Nigeria where snail farming is widely practised.
Data collection was through questionnaires administration and onsite
observation of farms. Data obtained were subjected to
descriptive statistics, Student-s t-test and regression analysis. Cost
benefit ratio (CBR) and rate of return on investment (RORI) were
calculated in order to determine the poverty alleviation potentials of
snail farming in the study areas. Although snail farming was
profitable and viable, it was below poverty line. With time and more
knowledge in its farming activities, and with more people taking to
snail production, its poverty alleviation and reduction potentials will
increase.
Abstract: The research study is carried out to determine the efficiency of the Biofilm sewage treatment plant which is located at the Engineering Complex-s. Wastewater analyses have been carried out at the Environmental Engineering laboratory to study the six parameters: Biochemical Oxygen Demand BOD, Chemical Oxygen Demand COD l, and Total Suspended Solids TSS, Ammoniac Nitrogen NH3-N and Phosphorous P which have been selected to determine the wastewater quality. The plant was designed to treat 750 Pe (population equivalent) at hydraulic retention time of 5 hours in the aerobic zone. The results show that Biofilm wastewater treatment plant was able to treat sewage successfully at different flow condition. The discharge has fulfilled the Malaysia Environmental of Standard A water quality. The achieved BOD removal is more than 85%, COD is more than 80%, TSS is more than 80%, NH3-N is more than 70%, and P was more than 70%. The Biofilm system provides a very efficient process for sewage treatment and it is compact in structure thus minimizes the required land area.
Abstract: In vitro plant regeneration has been successfully obtained from basal shoot explant of Vetiveria zizanioides through indirect organogenesis. The explant was cultured in Murashige & Skoog’s (MS) media supplemented with 2,4-D, IAA, and kinetin in various concentrations. Callus was well induced in media supplemented with 2 ppm 2,4-D, 1 ppm IAA, and 1 ppm kinetin. This callus was then transferred to MS media supplemented with 1 - 5 ppm of BAP for shoot regeneration. The media supplemented with 3 ppm BAP was a suitable medium for shoot induction, as well as for shoot multiplication. Rooting was well developed in shoot following transferred to half MS media containing 0.2 ppm IBA. Plantlet was then transferred to husk charcoal for acclimatization, and almost all (90%) of plantlets were survived during acclimatization.
Abstract: This paper presents the exergy analysis of a
desalination unit using humidification-dehumidification process.
Here, this unit is considered as a thermal system with three main
components, which are the heating unit by using a solar collector, the
evaporator or the humidifier, and the condenser or the dehumidifier.
In these components the exergy is a measure of the quality or grade
of energy and it can be destroyed in them. According to the second
law of thermodynamics this destroyed part is due to irreversibilities
which must be determined to obtain the exergetic efficiency of the
system.
In the current paper a computer program has been developed using
visual basic to determine the exergy destruction and the exergetic
efficiencies of the components of the desalination unit at variable
operation conditions such as feed water temperature, outlet air
temperature, air to feed water mass ratio and salinity, in addition to
cooling water mass flow rate and inlet temperature, as well as
quantity of solar irradiance.
The results obtained indicate that the exergy efficiency of the
humidifier increases by increasing the mass ratio and decreasing the
outlet air temperature. In the other hand the exergy efficiency of the
condenser increases with the increase of this ratio and also with the
increase of the outlet air temperature.
Abstract: A study was carried out at the Rice Research Institute of Iran (RRII) to investigate the effect of rollers differential peripheral speed of commercial rubber roll husker and paddy moisture content on the husking index and percentage of broken rice. The experiment was conducted at six levels of rollers differential speed (1.5, 2.2, 2.9, 3.6, 4.3 and 5 m/s) and three levels of paddy moisture content (8-9, 10-11 and 12-13% w.b.). Two common paddy varieties namely, Binam and Khazer, were selected for this study. Results revealed that the effect of rollers differential speed and moisture content significantly (P
Abstract: In this paper, experimental testing and numerical analysis were used to investigate the effect of tube thickness on the face bending for concrete filled hollow sections connected to other structural members using Extended Hollobolts. Six samples were tested experimentally by applying pull-out load on the bolts. These samples were designed to fail by column face bending. The main variable in all tests is the column face thickness. Finite element analyses were also performed using ABAQUS 6.11 to extend the experimental results and to quantify the effect of column face thickness. Results show that, the column face thickness has a clear impact on the connection strength and stiffness. However, the amount of improvement in the connection stiffness by changing the column face thickness from 5mm to 6.3mm seems to be higher than that when increasing it from 6.3mm to 8mm. The displacement at which the bolts start pulling-out from their holes increased with the use of thinner column face due to the high flexibility of the section. At the ultimate strength, the yielding of the column face propagated to the column corner and there was no yielding in its walls. After the ultimate resistance is reached, the propagation of the yielding was mainly in the column face with a miner yielding in the walls.
Abstract: A full six degrees of freedom (6-DOF) flight dynamics
model is proposed for the accurate prediction of short and long-range
trajectories of high spin and fin-stabilized projectiles via atmospheric
flight to final impact point. The projectiles is assumed to be both rigid
(non-flexible), and rotationally symmetric about its spin axis launched
at low and high pitch angles. The mathematical model is based on the
full equations of motion set up in the no-roll body reference frame and
is integrated numerically from given initial conditions at the firing
site. The projectiles maneuvering motion depends on the most
significant force and moment variations, in addition to wind and
gravity. The computational flight analysis takes into consideration the
Mach number and total angle of attack effects by means of the
variable aerodynamic coefficients. For the purposes of the present
work, linear interpolation has been applied from the tabulated database
of McCoy-s book. The developed computational method gives
satisfactory agreement with published data of verified experiments and
computational codes on atmospheric projectile trajectory analysis for
various initial firing flight conditions.
Abstract: Electrocardiogram (ECG) data compression algorithm
is needed that will reduce the amount of data to be transmitted, stored
and analyzed, but without losing the clinical information content. A
wavelet ECG data codec based on the Set Partitioning In Hierarchical
Trees (SPIHT) compression algorithm is proposed in this paper. The
SPIHT algorithm has achieved notable success in still image coding.
We modified the algorithm for the one-dimensional (1-D) case and
applied it to compression of ECG data.
By this compression method, small percent root mean square
difference (PRD) and high compression ratio with low
implementation complexity are achieved. Experiments on selected
records from the MIT-BIH arrhythmia database revealed that the
proposed codec is significantly more efficient in compression and in
computation than previously proposed ECG compression schemes.
Compression ratios of up to 48:1 for ECG signals lead to acceptable
results for visual inspection.
Abstract: It is a challenge to provide a wide range of queries to
database query systems for small mobile devices, such as the PDAs
and cell phones. Currently, due to the physical and resource
limitations of these devices, most reported database querying systems
developed for them are only offering a small set of pre-determined
queries for users to possibly pose. The above can be resolved by
allowing free-form queries to be entered on the devices. Hence, a
query language that does not restrict the combination of query terms
entered by users is proposed. This paper presents the free-form query
language and the method used in translating free-form queries to
their equivalent SQL statements.
Abstract: Gradual patterns have been studied for many years as
they contain precious information. They have been integrated in
many expert systems and rule-based systems, for instance to reason
on knowledge such as “the greater the number of turns, the greater
the number of car crashes”. In many cases, this knowledge has been
considered as a rule “the greater the number of turns → the greater
the number of car crashes” Historically, works have thus been
focused on the representation of such rules, studying how implication
could be defined, especially fuzzy implication. These rules were
defined by experts who were in charge to describe the systems they
were working on in order to turn them to operate automatically. More
recently, approaches have been proposed in order to mine databases
for automatically discovering such knowledge. Several approaches
have been studied, the main scientific topics being: how to determine
what is an relevant gradual pattern, and how to discover them as
efficiently as possible (in terms of both memory and CPU usage).
However, in some cases, end-users are not interested in raw level
knowledge, and are rather interested in trends. Moreover, it may be
the case that no relevant pattern can be discovered at a low level of
granularity (e.g. city), whereas some can be discovered at a higher
level (e.g. county). In this paper, we thus extend gradual pattern
approaches in order to consider multiple level gradual patterns. For
this purpose, we consider two aggregation policies, namely
horizontal and vertical.
Abstract: Tackling emergency situations is performed based on emergency scenarios. These scenarios do not have a uniform form in the Czech Republic. They are unstructured and developed primarily in the text form. This does not allow solving emergency situations efficiently. For this reason, the paper aims at defining a Process Oriented Architecture to support and thus to improve tackling emergency situations in the Czech Republic. The innovative Process Oriented Architecture is based on the Workflow Reference Model while taking into account the options of Business Process Management Suites for the implementation of process oriented emergency scenarios. To verify the proposed architecture the Proof of Concept has been used which covers the reception of an emergency event at the district emergency operations centre. Within the particular implementation of the proposed architecture the Bonita Open Solution has been used. The architecture created in this way is suitable not only for emergency management, but also for educational purposes.
Abstract: Sediment formation and its transport along the river course is considered as important hydraulic consideration in river engineering. Their impact on the morphology of rivers on one hand and important considerations of which in the design and construction of the hydraulic structures on the other has attracted the attention of experts in arid and semi-arid regions. Under certain conditions where the momentum energy of the flow stream reaches a specific rate, the sediment materials start to be transported with the flow. This can usually be analyzed in two different categories of suspended and bed load materials. Sedimentation phenomenon along the waterways and the conveyance of vast volume of materials into the canal networks can potentially influence water abstraction in the intake structures. This can pose a serious threat to operational sustainability and water delivery performance in the canal networks. The situation is serious where ineffective watershed management (poor vegetation cover in the water basin) is the underlying cause of soil erosion which feeds the materials into the waterways that intern would necessitate comprehensive study. The present paper aims to present an analytical investigation of the sediment process in the waterways on one hand and estimation of the sediment load transport into the lined canals using the SHARC software on the other. For this reason, the paper focuses on the comparative analysis of the hydraulic behaviors of the Sabilli main canal that feeds the pumping station with that of the Western canal in the Greater Dezful region to identify effective factors in sedimentation and ways of mitigating their impact on water abstraction in the canal systems. The method involved use of observational data available in the Dezful Dastmashoon hydrometric station along a 6 km waterway of the Sabilli main canal using the SHARC software to estimate the suspended load concentration and bed load materials. Results showed the transport of a significant volume of sediment loads from the waterways into the canal system which is assumed to have arisen from the absence of stilling basin on one hand and the gravity flow on the other has caused serious challenges. This is contrary to what occurs in the Sabilli canal, where the design feature which incorporates a settling basin just before the pumping station is the major cause of reduced sediment load transport into the canal system.Results showed that modification of the present design features by constructing a settling basin just upstream of the western intake structure can considerably reduce the entry of sediment materials into the canal system. Not only this can result in the sustainability of the hydraulic structures but can also improve operational performance of water conveyance and distribution system, all of which are the pre-requisite to secure reliable and equitable water delivery regime for the command area.
Abstract: This paper presents results obtained from the
numerical solution for the flow past an oscillating circular cylinder at
Reynolds number of 200. The frequency of oscillation was fixed to
the vortex shedding frequency from a fixed cylinder, f0, while the
amplitudes of oscillations were varied from to 1.1a, where a
represents the radius of the cylinder. The response of the flow
through the fluid forces acting on the surface of the cylinder are
investigated. The lock-on phenomenon is captured at low oscillation
amplitudes.
Abstract: Laser soldering is based on applying some soldering material (albumin) onto the approximated edges of the cut and heating the solder (and the underlying tissues) by a laser beam. Endogenous and exogenous materials such as indocyanine green (ICG) are often added to solders to enhance light absorption. Gold nanoshells are new materials which have an optical response dictated by the plasmon resonance. The wavelength at which the resonance occurs depends on the core and shell sizes, allowing nanoshells to be tailored for particular applications. The purposes of this study was use combination of ICG and different concentration of gold nanoshells for skin tissue soldering and also to examine the effect of laser soldering parameters on the properties of repaired skin. Two mixtures of albumin solder and different combinations of ICG and gold nanoshells were prepared. A full thickness incision of 2×20 mm2 was made on the surface and after addition of mixtures it was irradiated by an 810nm diode laser at different power densities. The changes of tensile strength σt due to temperature rise, number of scan (Ns), and scan velocity (Vs) were investigated. The results showed at constant laser power density (I), σt of repaired incisions increases by increasing the concentration of gold nanoshells in solder, Ns and decreasing Vs. It is therefore important to consider the tradeoff between the scan velocity and the surface temperature for achieving an optimum operating condition. In our case this corresponds to σt =1800 gr/cm2 at I~ 47 Wcm-2, T ~ 85ºC, Ns =10 and Vs=0.3mms-1.
Abstract: Color categorization is shared among members in a
society. This allows communication of color, especially when using
natural language such as English. Hence sociable robot, to live
coexist with human in human society, must also have the shared
color categorization. To achieve this, many works have been done
relying on modeling of human color perception and mathematical
complexities. In contrast, in this work, the computer as brain of the
robot learns color categorization through interaction with humans
without much mathematical complexities.