Abstract: The effect of cross linking of the protein isolates of
three legumes with the microbial enzyme transglutaminase (EC
2.3.2.13) on the functional properties at different NaCl concentration
was studied. The reduction in the total free amino groups (OD340) of
the polymerized protein showed that TGase treatment cross-linking
the protein subunit of each legume. The solubility of the protein
polymer of each legume was greatly improved at high concentration
of NaCl. At 1.2 M NaCl the solubility of the native legumes protein
was significantly decreased but after polymerization slightly
improved. Cross linked proteins were less turbid on heating to higher
temperature as compared to native proteins and the temperature at
which the protein turns turbid also increased in the polymerized
proteins. The emulsifying and foaming properties of the protein
polymer were greatly improved at all concentrations of NaCl for all
legumes.
Abstract: Most HWRs currently use natural uranium fuel. Using enriched uranium fuel results in a significant improvement in fuel cycle costs and uranium utilization. On the other hand, reactivity changes of HWRs over the full range of operating conditions from cold shutdown to full power are small. This reduces the required reactivity worth of control devices and minimizes local flux distribution perturbations, minimizing potential problems due to transient local overheating of fuel. Analyzing heavy water effectiveness on neutronic parameters such as enrichment requirements, peaking factor and reactivity is important and should pay attention as primary concepts of a HWR core designing. Two nuclear nuclear reactors of CANDU-type and hexagonal-type reactor cores of 33 fuel assemblies and 19 assemblies in 1.04 P/D have been respectively simulated using MCNP-4C code. Using heavy water and light water as moderator have been compared for achieving less reactivity insertion and enrichment requirements. Two fuel matrixes of (232Th/235U)O2 and (238/235U)O2 have been compared to achieve more economical and safe design. Heavy water not only decreased enrichment needs, but it concluded in negative reactivity insertions during moderator density variations. Thorium oxide fuel assemblies of 2.3% enrichment loaded into the core of heavy water moderator resulted in 0.751 fission to absorption ratio and peaking factor of 1.7 using. Heavy water not only provides negative reactivity insertion during temperature raises which changes moderator density but concluded in 2 to 10 kg reduction of enrichment requirements, depend on geometry type.
Abstract: The paper describes ergonomics problems trend of
student at B5101 classroom building 2, Suranaree University of
Technology. The objective to survey ergonomics problems and effect
from use chairs for sitting in class room. The result from survey
method 100 student they use lecture chair for sitting in classroom
more than 2 hours/ day by RULA[1]. and Body discomfort survey[2].
The result from Body discomfort survey contribute fatigue problems
at neck, lower back, upper back and right shoulder 2.93, 2.91, 2.33,
1.75 respectively and result from RULA contribute fatigue problems
at neck, body and right upper arm 4.00, 3.75 and 3.00 respectively
are consistent. After that the researcher provide improvement plan
for design new chair support student fatigue reduction by prepare
data of sample anthropometry and design ergonomics chair prototype
3 unit. Then sample 100 student trial to use new chair and evaluate
again by RULA, Body discomfort and satisfaction. The result from
trial new chair after improvement by RULA present fatigue reduction
average of head and neck from 4.00 to 2.25 , body and trunk from
3.75 to 2.00 and arm force from 1.00 to 0.25 respectively. The result
from trial new chair after improvement by Body discomfort present
fatigue reduction average of lower back from 2.91 to 0.87, neck from
2.93 to 1.24, upper back 2.33 to 0.84 and right upper arm from 1.75
to 0.74. That statistical of RULA and Body discomfort survey
present fatigue reduction after improvement significance with a
confidence level of 95% (p-value 0.05). When analyzing the
relationship of fatigue as part of the body by Chi – square test during
RULA and Body discomfort that before and after improvements were
consistent with the significant level of confidence 95% (p-value 0.05)
. Moreover the students satisfaction result from trial with a new chair
for 30 minutes [3]. 72 percent very satisfied of the folding of the
secondary writing simple 66% the width of the writing plate, 64% the
suitability of the writing plate, 62% of soft seat cushion and 61%
easy to seat the chair.
Abstract: This study focuses on emission of black carbon (BC)
from field open burning of corn residues. Real-time BC
concentration was measured by Micro Aethalometer from field
burning and simulated open burning in a chamber (SOC)
experiments. The average concentration of BC was 1.18±0.47 mg/m3
in the field and 0.89±0.63 mg/m3 in the SOC. The deduced emission
factor from field experiments was 0.50±0.20 gBC/kgdm, and 0.56±0.33
gBC/kgdm from SOC experiment, which are in good agreement with
other studies. In 2007, the total burned area of corn crop was 8,000
ha, resulting in an emission load of BC 20 ton corresponding to 44.5
million kg CO2 equivalent. Therefore, the control of open burning in
corn field represents a significant global warming reduction option.
Abstract: In order to enhance the aircraft survivability, the
infrared signatures emitted by hot engine parts should be determined
exactly. For its reduction it is necessary for the rear fuselage
temperature to be decreased. In this study, numerical modeling of flow
fields and heat transfer characteristics of an aircraft nozzle is
performed and its temperature distribution along each component wall
is predicted. The radiation shield is expected to reduce the skin
temperature of rear fuselage. The effect of material characteristic of
radiation shield on the heat transfer is also investigated. Through this
numerical analysis, design parameters related to the susceptibility of
aircraft are examined.
Abstract: Subsonic wind tunnel experiments were conducted to
study the effect of tripped boundary layer on the pressure distribution
in the contraction region of the tunnel. Measurements were
performed by installing trip strip at two different positions in the
concave portion of the contraction. The results show that installation
of the trip strips, have significant effects on both turbulence and
pressure distribution. The reduction in the free stream turbulence and
reduction of the wall static pressure distribution deferred signified
with the location of the trip strip.
Abstract: Leprosy is an infectious disease caused by
Mycobacterium Leprae, this disease, generally, compromises
the neural fibers, leading to the development of disability.
Disabilities are changes that limit daily activities or social life
of a normal individual. When comes to leprosy, the study of
disability considered the functional limitation (physical
disabilities), the limitation of activity and social participation,
which are measured respectively by the scales: EHF, SALSA
and PARTICIPATION SCALE. The objective of this work is
to propose an on-line monitoring of leprosy patients, which is
based on information scales EHF, SALSA and
PARTICIPATION SCALE. It is expected that the proposed
system is applied in monitoring the patient during treatment
and after healing therapy of the disease. The correlations that
the system is between the scales create a variety of
information, presented the state of the patient and full of
changes or reductions in disability. The system provides
reports with information from each of the scales and the
relationships that exist between them. This way, health
professionals, with access to patient information, can
intervene with techniques for the Prevention of Disability.
Through the automated scale, the system shows the level of
the patient and allows the patient, or the responsible, to take a
preventive measure. With an online system, it is possible take
the assessments and monitor patients from anywhere.
Abstract: Pre-germinated parboiled brown rice or Khao hang (in Thai) is paddy which undergoing the processes of soaking, steaming, drying and dehusking to obtain the edible form for consumption. The objectives of this research were to study the kinetic of pre-germinated parboiled brown rice drying using fluidization technique and to study the properties of pre-germinated parboiled brown rice after drying. The dryings were performed at the different temperatures of 110, 120 and 130 oC at the bed depth of 2 cm with the air velocity of 1.98 m/s. The results found that the higher drying temperature led to the faster moisture reduction. After drying until the moisture content of pre-germinated parboiled brown rice was lower than 14%wet basis, samples were taken to determine various qualities such as percentage of head rice and L* a* b* color values. The shade drying was used as a control. The results found that the higher drying temperature resulted in the decrease of head rice percentage. For the color assessment, the trend of L* and a* values was increased with the drying temperature, while the b* value was not significantly difference (p › 0.05) by drying temperatures. However, the b value of drying by fluidized bed dryer was higher than the control.
Abstract: So much energy is used in high rise buildings to fulfill
the basic needs of users such as lighting and thermal comfort.
Malaysia has hot and humid climate, buildings especially high rise
buildings receive unnecessary solar radiation that cause more solar
heat gain. Energy use specially electricity consumption in high rise
buildings has increased. There have been growing concerns about
energy consumption and its effect on environment. Building, energy
and the environment are important issues that the designers should
consider to them. Self protected form is one of possible ways against
the impact of solar radiation in high rise buildings. The Energy
performance of building envelopes was investigated in term of the
Overall Thermal Transfer Value (OTTV ).In this paper, the amount
of OTTV reduction was calculated through OTTV Equations to
clear the effectiveness of self shading strategy on minimizing energy
consumption for cooling interior spaces in high rise buildings which
has considerable envelope areas against solar radiation. Also increasing
the optimum window area was investigated using self-shading
strategy in designing high rise buildings. As result, the significant
reduction in OTTV was shown based on WWR.In addition slight
increase was demonstrated in WWR that can influence on visible
comfort interior spaces.
Abstract: Today automobile and aerospace industries realise Laser Beam Welding for a clean and non contact source of heating and fusion for joining of sheets. The welding performance is mainly based on by the laser welding parameters. Some concepts related to Artificial Neural Networks and how can be applied to model weld bead geometry and mechanical properties in terms of equipment parameters are reported in order to evaluate the accuracy and compare it with traditional modeling schemes. This review reveals the output features of Titanium and Aluminium weld bead geometry and mechanical properties such as ultimate tensile strength, yield strength, elongation and reduction of the area of the weld using Artificial Neural Network.
Abstract: Electro-hydraulic power steering (EHPS) system for
the fuel rate reduction and steering feel improvement is comprised of
ECU including the logic which controls the steering system and BL
DC motor and produces the best suited cornering force, BLDC motor,
high pressure pump integrated module and basic oil-hydraulic circuit
of the commercial HPS system.
Electro-hydraulic system can be studied in two ways such as
experimental and computer simulation. To get accurate results in
experimental study of EHPS system, the real boundary management is
necessary which is difficult task. And the accuracy of the experimental
results depends on the preparation of the experimental setup and
accuracy of the data collection. The computer simulation gives
accurate and reliable results if the simulation is carried out considering
proper boundary conditions. So, in this paper, each component of
EHPS was modeled, and the model-based analysis and control logic
was designed by using AMESim
Abstract: In this paper, a new model order reduction
phenomenon is introduced at the design stage of linear phase digital
IIR filter. The complexity of a system can be reduced by adopting the
model order reduction method in their design. In this paper a mixed
method of model order reduction is proposed for linear IIR filter. The
proposed method employs the advantages of factor division technique
to derive the reduced order denominator polynomial and the reduced
order numerator is obtained based on the resultant denominator
polynomial. The order reduction technique is used to reduce the delay
units at the design stage of IIR filter. The validity of the proposed
method is illustrated with design example in frequency domain and
stability is also examined with help of nyquist plot.
Abstract: This paper introduces the effective speckle reduction of
synthetic aperture radar (SAR) images using inner product spaces in
undecimated wavelet domain. There are two major areas in projection
onto span algorithm where improvement can be made. First is the use
of undecimated wavelet transformation instead of discrete wavelet
transformation. And second area is the use of smoothing filter namely
directional smoothing filter which is an additional step. Proposed
method does not need any noise estimation and thresholding
technique. More over proposed method gives good results on both
single polarimetric and fully polarimetric SAR images.
Abstract: Nowadays, consumption of whole flours and flours
with high extraction rate is recommended, because of their high
amount of fibers, vitamins and minerals. Despite nutritional benefits
of whole flour, concentration of some undesirable components such
as phytic acid is higher than white flour. In this study, effect of
several lactic acid bacteria sourdough on Toast bread is investigated.
Sourdough from lactic acid bacteria (Lb. plantarum, Lb. reuteri) with
different dough yield (250 and 300) is made and incubated at 30°C
for 20 hour, then added to dough in the ratio of 10, 20 and 30%
replacement. Breads that supplemented with Lb. plantarum
sourdough had lower phytic acid. Higher replacement of sourdough
and higher DY cause higher decrease in phytic acid content.
Sourdough from Lb. plantarum, DY = 300 and 30% replacement
cause the highest decrease in phytic acid content (49.63 mg/100g).
As indicated by panelists, Lb. reuteri sourdough can present the
greatest effect on overall quality score of the breads. DY reduction
cause a decrease in bread quality score. Sensory score of Toast bread
is 81.71 in the samples that treated with Lb. reuteri sourdough with
DY = 250 and 20% replacement.
Abstract: The growing outsourcing of logistics services
resulting from the ongoing current in firms of costs
reduction/increased efficiency means that it is becoming more and
more important for the companies doing the outsourcing to carry out
a proper evaluation.
The multiple definitions and measures of logistics service
performance found in research on the topic create a certain degree of
confusion and do not clear the way towards the proper measurement
of their performance. Do a model and a specific set of indicators exist
that can be considered appropriate for measuring the performance of
logistics services outsourcing in industrial environments? Are said
indicators in keeping with the objectives pursued by outsourcing? We
aim to answer these and other research questions in the study we have
initiated in the field within the framework of the international High
Performance Manufacturing (HPM) project of which this paper
forms part.
As the first stage of this research, this paper reviews articles
dealing with the topic published in the last 15 years with the aim of
detecting the models most used to make this measurement and
determining which performance indicators are proposed as part of
said models and which are most used. The first steps are also taken in
determining whether these indicators, financial and operational, cover
the aims that are being pursued when outsourcing logistics services.
The findings show there is a wide variety of both models and
indicators used. This would seem to testify to the need to continue
with our research in order to try to propose a model and a set of
indicators for measuring the performance of logistics services
outsourcing in industrial environments.
Abstract: To investigate the behavior of sheet metals during
forming tailor welded blanks (TWB) of various thickness made via
Co2 Laser welding are under consideration. These blanks are formed
used two different forming methods of rubber as well as the
conventional punch and die methods. The main research objective is
the effects of using a rubber die instead of a solid one the
displacement of the weld line and the press force needed for forming.
Specimens with thicknesses of 0.5, 0.6, 0.8 and 1mm are subjected to
Erichsen two dimensional tests and the resulted force for each case
are compared. This is followed by a theoretical and numerical study
of press force and weld line displacement. It is concluded that using
rubber pad forming (RPF) causes a reduction in weld line
displacement and an increase in the press force.
Abstract: Ratio and regression type estimators have been used by previous authors to estimate a population mean for the principal variable from samples in which both auxiliary x and principal y variable data are available. However, missing data are a common problem in statistical analyses with real data. Ratio and regression type estimators have also been used for imputing values of missing y data. In this paper, six new ratio and regression type estimators are proposed for imputing values for any missing y data and estimating a population mean for y from samples with missing x and/or y data. A simulation study has been conducted to compare the six ratio and regression type estimators with a previous estimator of Rueda. Two population sizes N = 1,000 and 5,000 have been considered with sample sizes of 10% and 30% and with correlation coefficients between population variables X and Y of 0.5 and 0.8. In the simulations, 10 and 40 percent of sample y values and 10 and 40 percent of sample x values were randomly designated as missing. The new ratio and regression type estimators give similar mean absolute percentage errors that are smaller than the Rueda estimator for all cases. The new estimators give a large reduction in errors for the case of 40% missing y values and sampling fraction of 30%.
Abstract: Tip vortex cavitation is one of well known patterns of
cavitation phenomenon which occurs in axial pumps. This pattern of
cavitation occurs due to pressure difference between the pressure and
suction sides of blades of an axial pump. Since the pressure in the
pressure side of the blade is higher than the pressure in its suction
side, thus a very small portion of liquid flow flows back from
pressure side to the suction side. This fact is cause of tip vortex
cavitation and gap cavitation that may occur in axial pumps. In this
paper the results of our experimental investigation about movement
of tip vortex cavitation along blade edge due to reduction of pump
flow rate in an axial pump is reported. Results show that reduction of
pump flow rate in conjunction with increasing of outlet pressure
causes movement of tip vortex cavitation along blade edge towards
the blade tip. Results also show that by approaching tip vortex
cavitation to the blade tip, vortex tip pattern of cavitation replaces
with a cavitation phenomenon on the blade tip. Furthermore by
further reduction of pump flow rate and increasing of outlet pressure,
an unstable cavitation phenomenon occurs between each blade
leading edge and the next blade trailing edge.
Abstract: Interior brick-infill partitions are usually considered as
non-structural components, and only their weight is accounted for in
practical structural design. In this study, the brick-infill panels are
simulated by compression struts to clarify their effect on the
progressive collapse potential of an earthquake-resistant RC building.
Three-dimensional finite element models are constructed for the RC
building subjected to sudden column loss. Linear static analyses are
conducted to investigate the variation of demand-to-capacity ratio
(DCR) of beam-end moment and the axial force variation of the beams
adjacent to the removed column. Study results indicate that the
brick-infill effect depends on their location with respect to the
removed column. As they are filled in a structural bay with a shorter
span adjacent to the column-removed line, more significant reduction
of DCR may be achieved. However, under certain conditions, the
brick infill may increase the axial tension of the two-span beam
bridging the removed column.
Abstract: Applying a rigorous process to optimize the elements
of a supply-chain network resulted in reduction of the waiting time
for a service provider and customer. Different sources of downtime
of hydraulic pressure controller/calibrator (HPC) were causing
interruptions in the operations. The process examined all the issues to
drive greater efficiencies. The issues included inherent design issues
with HPC pump, contamination of the HPC with impurities, and the
lead time required for annual calibration in the USA.
HPC is used for mandatory testing/verification of formation
tester/pressure measurement/logging-while drilling tools by oilfield
service providers, including Halliburton.
After market study andanalysis, it was concluded that the current
HPC model is best suited in the oilfield industry. To use theexisting
HPC model effectively, design andcontamination issues were
addressed through design and process improvements. An optimum
network is proposed after comparing different supply-chain models
for calibration lead-time reduction.