Abstract: In this work, a Multi-Level Artificial Bee Colony
(called MLABC) for optimizing numerical test functions is presented.
In MLABC, two species are used. The first species employs n
colonies where each of them optimizes the complete solution vector.
The cooperation between these colonies is carried out by exchanging
information through a leader colony, which contains a set of elite
bees. The second species uses a cooperative approach in which the
complete solution vector is divided to k sub-vectors, and each of
these sub-vectors is optimized by a colony. The cooperation between
these colonies is carried out by compiling sub-vectors into the
complete solution vector. Finally, the cooperation between two
species is obtained by exchanging information. The proposed
algorithm is tested on a set of well-known test functions. The results
show that MLABC algorithm provides efficiency and robustness to
solve numerical functions.
Abstract: We propose a new alternative method for imposing
fluid-solid boundary conditions in simulations of Multiparticle
Collision Dynamics. Our method is based on the introduction of
an explicit potential force acting between the fluid particles and a
surface representing a solid boundary. We show that our method can
be used in simulations of plane Poiseuille flows. Important quantities
characterizing the flow and the fluid-solid interaction like the slip
coefficient at the solid boundary and the effective viscosity of the
fluid, are measured in terms of the set of independent parameters
defining the numerical implementation. We find that our method can
be used to simulate the correct hydrodynamic flow within a wide
range of values of these parameters.
Abstract: In this paper a novel design of aerostatic thrust bearing
is proposed and is analyzed numerically. The capillary restrictor and
bearing disk are made of elastomer like silicone and PU. The
viscoelasticity of elastomer helps the capillary expand for more air
flux and at the same time, allows conicity of the bearing surface to
form when the air pressure is enhanced. Therefore the bearing has the
better ability of passive compensation. In the present example, as
compared with the typical model, the new designs can nearly double
the load capability and offer four times static stiffness.
Abstract: This paper reports the numerical and experimental
performances of Double Glass Wall are investigated. Two
configurations were considered namely, the Double Clear Glass Wall
(DCGW) and the Double Translucent Glass Wall (DTGW). The
coupled governing equations as well as boundary conditions are
solved using the finite element method (FEM) via COMSOLTM
Multiphysics. Temperature profiles and flow field of the DCGW and
DTGW are reported and discussed. Different constant heat fluxes
were considered as 400 and 800 W.m-2 the corresponding initial
condition temperatures were 30.5 and 38.5ºC respectively. The
results show that the simulation results are in agreement with the
experimental data. Conclusively, the model considered in this study
could reasonable be used simulate the thermal and ventilation
performance of the DCGW and DTGW configurations.
Abstract: In an urban area the location allocation of emergency
services mobile units, such as ambulances, police patrol cars must be
designed so as to achieve a prompt response to demand locations.
In this paper the partition of a given urban network into distinct
sub-networks is performed such that the vertices in each component
are close and simultaneously the sums of the corresponding
population in the sub-networks are almost uniform. The objective
here is to position appropriately in each sub-network a mobile
emergency unit in order to reduce the response time to the demands.
A mathematical model in framework of graph theory is developed.
In order to clarify the corresponding method a relevant numerical
example is presented on a small network.
Abstract: The thermo-mechanical behaviour of concrete energy
pile foundations with different single and double U-tube shapes
incorporated was analysed using the Comsol Multi-physics package.
For the analysis, a 3D numerical model in real scale of the concrete
pile and surrounding soil was simulated regarding actual operation of
ground heat exchangers (GHE) and the surrounding ambient
temperature. Based on initial ground temperature profile measured in
situ, tube inlet temperature was considered to range from 6oC to 0oC
(during the contraction process) over a 30-day period. Extra thermal
stresses and deformations were calculated during the simulations and
differences arising from the use of two different systems (single-tube
and double-tube) were analysed. The results revealed no significant
difference for extra thermal stresses at the centre of the pile in either
system. However, displacements over the pile length were found to
be up to 1.5-fold higher in the double-tube system than the singletube
system.
Abstract: A computational fluid dynamics simulation is done for
non-Newtonian fluid in a baffled stirred tank. The CMC solution is
taken as non-Newtonian shear thinning fluid for simulation. The
Reynolds Average Navier Stocks equation with steady state multi
reference frame approach is used to simulate flow in the stirred tank.
The turbulent flow field is modelled using realizable k-ε turbulence
model. The simulated velocity profiles of Rushton turbine is
validated with literature data. Then, the simulated flow field of CD-6
impeller is compared with the Rushton turbine. The flow field
generated by CD-6 impeller is less in magnitude than the Rushton
turbine. The impeller global parameter, power number and flow
number, and entropy generation due to viscous dissipation rate is also
reported.
Abstract: Present study is aimed on the cutting process of circular
cross-section rods where the fracture is used to separate one rod
into two pieces. Incorporating the phenomenological ductile fracture
model into the explicit formulation of finite element method, the
process can be analyzed without the necessity of realizing too many
real experiments which could be expensive in case of repetitive
testing in different conditions. In the present paper, the steel AISI
1045 was examined and the tensile tests of smooth and notched
cylindrical bars were conducted together with biaxial testing of the
notched tube specimens to calibrate material constants of selected
phenomenological ductile fracture models. These were implemented
into the Abaqus/Explicit through user subroutine VUMAT and used
for cutting process simulation. As the calibration process is based
on variables which cannot be obtained directly from experiments,
numerical simulations of fracture tests are inevitable part of the
calibration. Finally, experiments regarding the cutting process were
carried out and predictive capability of selected fracture models is
discussed. Concluding remarks then make the summary of gained
experience both with the calibration and application of particular
ductile fracture criteria.
Abstract: In this paper, we introduce a generalized Chebyshev
collocation method (GCCM) based on the generalized Chebyshev
polynomials for solving stiff systems. For employing a technique
of the embedded Runge-Kutta method used in explicit schemes, the
property of the generalized Chebyshev polynomials is used, in which
the nodes for the higher degree polynomial are overlapped with those
for the lower degree polynomial. The constructed algorithm controls
both the error and the time step size simultaneously and further
the errors at each integration step are embedded in the algorithm
itself, which provides the efficiency of the computational cost. For
the assessment of the effectiveness, numerical results obtained by the
proposed method and the Radau IIA are presented and compared.
Abstract: The crude oil in an oil well exists in various phases
such as gas, seawater, and sand, as well as oil. Therefore, a phase
separator is needed at the front of a single-phase pump for
pressurization and transfer. On the other hand, the application of a
multiphase pump can provide such advantages as simplification of the
equipment structure and cost savings, because there is no need for a
phase separation process. Therefore, the crude oil transfer method
using a multiphase pump is being applied to recently developed oil
wells. Due to this increase in demand, technical demands for the
development of multiphase pumps are sharply increasing, but the
progress of research into related technologies is insufficient, due to the
nature of multiphase pumps that require high levels of skills. This
study was conducted to verify the reliability of pump performance
evaluation using numerical analysis, which is the basis of the
development of a multiphase pump. For this study, a model was
designed by selecting the specifications of this study. The performance
of the designed model was evaluated through numerical analysis and
experiment. The results of the performance evaluation were compared
to verify the reliability of the result using numerical analysis.
Abstract: This work presents a Computational Fluid Dynamics
(CFD) simulation of a butterfly valve used to control the flow of
combustible gas mixture in an industrial process setting.The work
uses CFD simulation to analyze the flow characteristics in the
vicinity of the valve, including the pressure distributions and
Frequency spectrum of the pressure pulsations downstream the valves
and the vortex shedding allow predicting the torque fluctuations
acting on the valve shaft and the possibility of generating mechanical
vibration and resonance.These fluctuations are due to aerodynamic
torque resulting from fluid turbulence and vortex shedding in the
valve vicinity.
The valve analyzed is located in a pipeline between two opposing
90o elbows, which exposes the valve and the surrounding structure to
the turbulence generated upstream and downstream the elbows at
either end of the pipe.CFD simulations show that the best location for
the valve from a vibration point of view is in the middle of the pipe
joining the elbows.
Abstract: The reachable set bounding estimation for distributed
delay systems with disturbances is a new problem. In this paper,we
consider this problem subject to not only time varying delay and
polytopic uncertainties but also distributed delay systems which is
not studied fully untill now. we can obtain improved non-ellipsoidal
reachable set estimation for neural networks with time-varying delay
by the maximal Lyapunov-Krasovskii fuctional which is constructed
as the pointwise maximum of a family of Lyapunov-Krasovskii
fuctionals corresponds to vertexes of uncertain polytope.On the other
hand,matrix inequalities containing only one scalar and Matlabs
LMI Toolbox is utilized to give a non-ellipsoidal description of the
reachable set.finally,numerical examples are given to illustrate the
existing results.
Abstract: In this paper, numerical solution of system of
Fredholm and Volterra integral equations by means of the Spline
collocation method is considered. This approximation reduces the
system of integral equations to an explicit system of algebraic
equations. The solution is collocated by cubic B-spline and the
integrand is approximated by the Newton-Cotes formula. The error
analysis of proposed numerical method is studied theoretically. The
results are compared with the results obtained by other methods to
illustrate the accuracy and the implementation of our method.
Abstract: A finite difference/front tracking method is used to
study the motion of three-dimensional deformable drops suspended in
plane Poiseuille flow at non-zero Reynolds numbers. A parallel
version of the code was used to study the behavior of suspension on a
reasonable grid resolution (grids). The viscosity and density of drops
are assumed to be equal to that of the suspending medium. The effect
of the Reynolds number is studied in detail. It is found that drops
with small deformation behave like rigid particles and migrate to an
equilibrium position about half way between the wall and the
centerline (the Segre-Silberberg effect). However, for highly
deformable drops there is a tendency for drops to migrate to the
middle of the channel, and the maximum concentration occurs at the
centerline. The effective viscosity of suspension and the fluctuation
energy of the flow across the channel increases with the Reynolds
number of the flow.
Abstract: The phased-array ultrasound transducer types are
utilities for medical ultrasonography as well as optical imaging.
However, their discontinuity characteristic limits the applications due
to the artifacts contaminated into the reconstructed images. Because
of the effects of the ultrasound pressure field pattern to the echo
ultrasonic waves as well as the optical modulated signal, the side
lobes of the focused ultrasound beam induced by discontinuity of the
phased-array ultrasound transducer might the reason of the artifacts.
In this paper, a simple method in approach of numerical simulation
was used to investigate the limitation of discontinuity of the elements
in phased-array ultrasound transducer and their effects to the
ultrasound pressure field. Take into account the change of ultrasound
pressure field patterns in the conditions of variation of the pitches
between elements of the phased-array ultrasound transducer, the
appropriated parameters for phased-array ultrasound transducer
design were asserted quantitatively.
Abstract: The purpose of this project is to carry out an analysis
and determine the profile of actual lean manufacturing processes in
the Metropolitan Area of Bucaramanga. Through the analysis of
qualitative and quantitative variables it was possible to establish how
these manufacturers develop production practices that ensure their
competitiveness and productivity in the market.
In this study, a random sample of metallurgic and wrought iron
companies was applied, following which a quantitative focus and
analysis was used to formulate a qualitative methodology for
measuring the level of lean manufacturing procedures in the industry.
A qualitative evaluation was also carried out through a multivariate
analysis using the Numerical Taxonomy System (NTSYS) program
which should allow for the determination of Lean Manufacturing
profiles.
Through the results it was possible to observe how the companies
in the sector are doing with respect to Lean Manufacturing Practices,
as well as identify the level of management that these companies
practice with respect to this topic. In addition, it was possible to
ascertain that there is no one dominant profile in the sector when it
comes to Lean Manufacturing.
It was established that the companies in the metallurgic and
wrought iron industry show low levels of Lean Manufacturing
implementation. Each one carries out diverse actions that are
insufficient to consolidate a sectoral strategy for developing a
competitive advantage which enables them to tie together a
production strategy.
Abstract: Stochastic User Equilibrium (SUE) model is a widely
used traffic assignment model in transportation planning, which is
regarded more advanced than Deterministic User Equilibrium (DUE)
model. However, a problem exists that the performance of the SUE
model depends on its error term parameter. The objective of this
paper is to propose a systematic method of determining the
appropriate error term parameter value for the SUE model. First, the
significance of the parameter is explored through a numerical
example. Second, the parameter calibration method is developed
based on the Logit-based route choice model. The calibration process
is realized through multiple nonlinear regression, using sequential
quadratic programming combined with least square method. Finally,
case analysis is conducted to demonstrate the application of the
calibration process and validate the better performance of the SUE
model calibrated by the proposed method compared to the SUE
models under other parameter values and the DUE model.
Abstract: Nonstandard tests are necessary for analyses and
verification of new developed structural and technological solutions
with application of composite materials. One of the most critical
primary structural parts of a typical aerospace structure is T-joint.
This structural element is loaded mainly in shear, bending, peel and
tension. The paper is focused on the shear loading simulations. The
aim of the work is to obtain a representative uniform distribution of
shear loads along T-joint during the mechanical testing. A new
design of T-joint test procedure, numerical simulation and
optimization of representative boundary conditions are presented.
The different conditions and inaccuracies both in simulations and
experiments are discussed. The influence of different parameters on
stress and strain distributions is demonstrated on T-joint made of
CFRP (carbon fibre reinforced plastic). A special test rig designed by
VZLU (Aerospace Research and Test Establishment) for T-shear test
procedure is presented.
Abstract: In this paper the effect of wall waviness of side walls
in a two-dimensional wavy enclosure is numerically investigated.
Two vertical wavy walls and straight top wall are kept isothermal and
the bottom wall temperature is higher and spatially varying with
cosinusoidal temperature distribution. A computational code based on
Finite-volume approach is used to solve governing equations and
SIMPLE method is used for pressure velocity coupling. Test is
performed for several different numbers of undulations. The Prandtl
number was kept constant and the Ra number denotes that the flow is
laminar. Temperature and velocity fields are determined. Therefore,
according to the obtained results a correlation is proposed for average
Nusselt number as a function of number of side wall waves. The
results indicate that the Nusselt number is highly affected by number
of waves and increasing it decreases the wavy walls Nusselt number;
although the Nusselt number is not highly affected by surface
waviness when the number of undulations is below one.
Abstract: This paper is devoted to the study of a viscous
incompressible flow around a circular cylinder performing harmonic
oscillations, especially the steady streaming phenomenon. The
research methodology is based on the asymptotic explanation method
combined with the computational bifurcation analysis. The research
approach develops Schlichting and Wang decomposition method.
Present studies allow to identify several regimes of the secondary
streaming with different flow structures. The results of the research
are in good agreement with experimental and numerical simulation
data.