Abstract: Synthesis gas manufacturing by steam reforming of hydrocarbons is an important industrial process. High endothermic nature of the process makes it one of the most cost and heat intensive processes. In the present work, composite effect of different inert gases on synthesis gas yield, feed gas conversion and temperature distribution along the reactor length has been studied using a heterogeneous model. Mathematical model was developed as a first stage and validated against the existing process models. With the addition of inert gases, a higher yield of synthesis gas is observed. Simultaneously the rector outlet temperature drops to as low as 810 K. It was found that Xenon gives the highest yield and conversion while Helium gives the lowest temperature. Using Xenon inert gas 20 percent reduction in outlet temperature was observed compared to traditional case.
Abstract: This paper presents two simplified models to
determine nodal voltages in power distribution networks. These
models allow estimating the impact of the installation of reactive
power compensations equipments like fixed or switched capacitor
banks. The procedure used to develop the models is similar to the
procedure used to develop linear power flow models of transmission
lines, which have been widely used in optimization problems of
operation planning and system expansion. The steady state non-linear
load flow equations are approximated by linear equations relating the
voltage amplitude and currents. The approximations of the linear
equations are based on the high relationship between line resistance
and line reactance (ratio R/X), which is valid for power distribution
networks. The performance and accuracy of the models are evaluated
through comparisons with the exact results obtained from the
solution of the load flow using two test networks: a hypothetical
network with 23 nodes and a real network with 217 nodes.
Abstract: Arms detection is one of the fundamental problems in
human motion analysis application. The arms are considered as the
most challenging body part to be detected since its pose and speed
varies in image sequences. Moreover, the arms are usually occluded
with other body parts such as the head and torso. In this paper,
histogram-based skin colour segmentation is proposed to detect the
arms in image sequences. Six different colour spaces namely RGB,
rgb, HSI, TSL, SCT and CIELAB are evaluated to determine the best
colour space for this segmentation procedure. The evaluation is
divided into three categories, which are single colour component,
colour without luminance and colour with luminance. The
performance is measured using True Positive (TP) and True Negative
(TN) on 250 images with manual ground truth. The best colour is
selected based on the highest TN value followed by the highest TP
value.
Abstract: Fly ash is a significant waste that is released of
thermal power plants and defined as very fine particles that are drifted upward with up taken by the flue gases due to the burning of
used coal [1]. The fly-ash is capable of removing organic
contaminants in consequence of high carbon content, a large surface area per unit volume and contained heavy metals. Therefore, fly ash
is used as an effective coagulant and adsorbent by pelletization [2, 3].
In this study, the possibility of use of fly ash taken from Turkey like low-cost adsorbent for adsorption of zinc ions found in waste
water was investigated. The fly ash taken from Turkey was pelletized with bentonite and molass to evaluate the adsorption capaticity. For
this purpose; analyses such as sieve analysis, XRD, XRF, FTIR and SEM were performed. As a result, it was seen that pellets prepared
from fly ash, bentonite and molass would be used for zinc adsorption.
Abstract: This paper describes a CMOS four-quadrant
multiplier intended for use in the front-end receiver by utilizing the
square-law characteristic of the MOS transistor in the saturation
region. The circuit is based on 0.35 um CMOS technology simulated
using HSPICE software. The mixer has a third-order inter the power
consumption is 271uW from a single 1.2V power supply. One of the
features of the proposed design is using two MOS transistors
limitation to reduce the supply voltage, which leads to reduce the
power consumption. This technique provides a GHz bandwidth
response and low power consumption.
Abstract: In-core memory requirement is a bottleneck in solving
large three dimensional Navier-Stokes finite element problem
formulations using sparse direct solvers. Out-of-core solution
strategy is a viable alternative to reduce the in-core memory
requirements while solving large scale problems. This study
evaluates the performance of various out-of-core sequential solvers
based on multifrontal or supernodal techniques in the context of
finite element formulations for three dimensional problems on a
Windows platform. Here three different solvers, HSL_MA78,
MUMPS and PARDISO are compared. The performance of these
solvers is evaluated on a 64-bit machine with 16GB RAM for finite
element formulation of flow through a rectangular channel. It is
observed that using out-of-core PARDISO solver, relatively large
problems can be solved. The implementation of Newton and
modified Newton's iteration is also discussed.
Abstract: Nowadays, engineering ceramics have significant
applications in different industries such as; automotive, aerospace,
electrical, electronics and even martial industries due to their
attractive physical and mechanical properties like very high hardness
and strength at elevated temperatures, chemical stability, low friction
and high wear resistance. However, these interesting properties plus
low heat conductivity make their machining processes too hard,
costly and time consuming. Many attempts have been made in order
to make the grinding process of engineering ceramics easier and
many scientists have tried to find proper techniques to economize
ceramics' machining processes. This paper proposes a new diamond
plunge grinding technique using ultrasonic vibration for grinding
Alumina ceramic (Al2O3). For this purpose, a set of laboratory
equipments have been designed and simulated using Finite Element
Method (FEM) and constructed in order to be used in various
measurements. The results obtained have been compared with the
conventional plunge grinding process without ultrasonic vibration
and indicated that the surface roughness and fracture strength
improved and the grinding forces decreased.
Abstract: The dynamics of User Datagram Protocol (UDP) traffic
over Ethernet between two computers are analyzed using nonlinear
dynamics which shows that there are two clear regimes in the data
flow: free flow and saturated. The two most important variables
affecting this are the packet size and packet flow rate. However,
this transition is due to a transcritical bifurcation rather than phase
transition in models such as in vehicle traffic or theorized large-scale
computer network congestion. It is hoped this model will help lay
the groundwork for further research on the dynamics of networks,
especially computer networks.
Abstract: High speed networks provide realtime variable bit rate
service with diversified traffic flow characteristics and quality
requirements. The variable bit rate traffic has stringent delay and
packet loss requirements. The burstiness of the correlated traffic
makes dynamic buffer management highly desirable to satisfy the
Quality of Service (QoS) requirements. This paper presents an
algorithm for optimization of adaptive buffer allocation scheme for
traffic based on loss of consecutive packets in data-stream and buffer
occupancy level. Buffer is designed to allow the input traffic to be
partitioned into different priority classes and based on the input
traffic behavior it controls the threshold dynamically. This algorithm
allows input packets to enter into buffer if its occupancy level is less
than the threshold value for priority of that packet. The threshold is
dynamically varied in runtime based on packet loss behavior. The
simulation is run for two priority classes of the input traffic –
realtime and non-realtime classes. The simulation results show that
Adaptive Partial Buffer Sharing (ADPBS) has better performance
than Static Partial Buffer Sharing (SPBS) and First In First Out
(FIFO) queue under the same traffic conditions.
Abstract: The increased number of automobiles in recent years
has resulted in great demand for fossil fuel. This has led to the
development of automobile by using alternative fuels which include
gaseous fuels, biofuels and vegetables oils as fuel. Energy from
biomass and more specific bio-diesel is one of the opportunities that
could cover the future demand of fossil fuel shortage. Biomass in the
form of cashew nut shell represents a new energy source and
abundant source of energy in India. The bio-fuel is derived from
cashew nut shell oil and its blend with diesel are promising
alternative fuel for diesel engine. In this work the pyrolysis Cashew
Nut Shell Liquid (CNSL)-Diesel Blends (CDB) was used to run the
Direct Injection (DI) diesel engine. The experiments were conducted
with various blends of CNSL and Diesel namely B20, B40, B60, B80
and B100. The results are compared with neat diesel operation. The
brake thermal efficiency was decreased for blends of CNSL and
Diesel except the lower blends of B20. The brake thermal efficiency
of B20 is nearly closer to that of diesel fuel. Also the emission level
of the all CNSL and Diesel blends was increased compared to neat
diesel. The higher viscosity and lower volatility of CNSL leads to
poor mixture formation and hence lower brake thermal efficiency and
higher emission levels. The higher emission level can be reduced by
adding suitable additives and oxygenates with CNSL and Diesel
blends.
Abstract: Network layer multicast, i.e. IP multicast, even after
many years of research, development and standardization, is not
deployed in large scale due to both technical (e.g. upgrading of
routers) and political (e.g. policy making and negotiation) issues.
Researchers looked for alternatives and proposed application/overlay
multicast where multicast functions are handled by end hosts, not
network layer routers. Member hosts wishing to receive multicast
data form a multicast delivery tree. The intermediate hosts in the tree
act as routers also, i.e. they forward data to the lower hosts in the
tree. Unlike IP multicast, where a router cannot leave the tree until all
members below it leave, in overlay multicast any member can leave
the tree at any time thus disjoining the tree and disrupting the data
dissemination. All the disrupted hosts have to rejoin the tree. This
characteristic of the overlay multicast causes multicast tree unstable,
data loss and rejoin overhead. In this paper, we propose that each node
sets its leaving time from the tree and sends join request to a number
of nodes in the tree. The nodes in the tree will reject the request if
their leaving time is earlier than the requesting node otherwise they
will accept the request. The node can join at one of the accepting
nodes. This makes the tree more stable as the nodes will join the tree
according to their leaving time, earliest leaving time node being at the
leaf of the tree. Some intermediate nodes may not follow their leaving
time and leave earlier than their leaving time thus disrupting the tree.
For this, we propose a proactive recovery mechanism so that disrupted
nodes can rejoin the tree at predetermined nodes immediately. We
have shown by simulation that there is less overhead when joining
the multicast tree and the recovery time of the disrupted nodes is
much less than the previous works. Keywords
Abstract: This paper presents the significant factor and give
some suggestion that should know before design. The main objective of this paper is guide the first step for someone who attends to design of grounding system before study in details later. The overview of
grounding system can protect damage from fault such as can save a human life and power system equipment. The unsafe conditions have
three cases. Case 1) maximum touch voltage exceeds the safety
criteria. In this case, the conductor compression ratio of the ground gird should be first adjusted to have optimal spacing of ground grid
conductors. If it still over limit, earth resistivity should be consider afterward. Case 2) maximum step voltage exceeds the safety criteria.
In this case, increasing the number of ground grid conductors around
the boundary can solve this problem. Case 3) both of maximum touch
and step voltage exceed the safety criteria. In this case, follow the solutions explained in case 1 and case 2. Another suggestion, vary depth of ground grid until maximum step and touch voltage do not
exceed the safety criteria.
Abstract: A model predictive controller based on recursive learning is proposed. In this SISO adaptive controller, a model is automatically updated using simple recursive equations. The identified models are then stored in the memory to be re-used in the future. The decision for model update is taken based on a new control performance index. The new controller allows the use of simple linear model predictive controllers in the control of nonlinear time varying processes.
Abstract: By introducing the concept of Oracle we propose an approach for improving the performance of genetic algorithms for large-scale asymmetric Traveling Salesman Problems. The results have shown that the proposed approach allows overcoming some traditional problems for creating efficient genetic algorithms.
Abstract: Increasing growth of information volume in the
internet causes an increasing need to develop new (semi)automatic
methods for retrieval of documents and ranking them according to
their relevance to the user query. In this paper, after a brief review
on ranking models, a new ontology based approach for ranking
HTML documents is proposed and evaluated in various
circumstances. Our approach is a combination of conceptual,
statistical and linguistic methods. This combination reserves the
precision of ranking without loosing the speed. Our approach
exploits natural language processing techniques to extract phrases
from documents and the query and doing stemming on words. Then
an ontology based conceptual method will be used to annotate
documents and expand the query. To expand a query the spread
activation algorithm is improved so that the expansion can be done
flexible and in various aspects. The annotated documents and the
expanded query will be processed to compute the relevance degree
exploiting statistical methods. The outstanding features of our
approach are (1) combining conceptual, statistical and linguistic
features of documents, (2) expanding the query with its related
concepts before comparing to documents, (3) extracting and using
both words and phrases to compute relevance degree, (4) improving
the spread activation algorithm to do the expansion based on
weighted combination of different conceptual relationships and (5)
allowing variable document vector dimensions. A ranking system
called ORank is developed to implement and test the proposed
model. The test results will be included at the end of the paper.
Abstract: The objective of the present study was to evaluate the
potential of hollow microneedles for enhancing the transdermal
delivery of Bovine Serum Albumin (MW~66,000 Da)-Fluorescein
Isothiocyanate (BSA-FITC) conjugate, a hydrophilic large molecular
compound. Moreover, the effect of different formulations was
evaluated. The series of binary mixtures composed of propylene
glycol (PG) and pH 7.4 phosphate buffer solution (PBS) was
prepared and used as a medium for BSA-FITC. The results showed
that there was no permeation of BSA-FITC solution across the
neonatal porcine skin without using hollow microneedles, whereas
the cumulative amount of BSA-FITC released at 8 h through the
neonatal porcine skin was about 60-70% when using hollow
microneedles. Furthermore, the results demonstrated that the higher
volume of PG in binary mixtures injected, the lower cumulative
amount of BSA-FITC released and release rate of BSA-FITC from
skin. These release profiles of BSA-FITC in binary mixtures were
expressed by Fick-s law of diffusion. These results suggest the
utilization of hollow microneedle to enhance transdermal delivery of
protein and provide useful information for designing an effective
hollow microneedle system.
Abstract: This paper presents a mathematical model and a
methodology to analyze the losses in transmission expansion
planning (TEP) under uncertainty in demand. The methodology is
based on discrete particle swarm optimization (DPSO). DPSO is a
useful and powerful stochastic evolutionary algorithm to solve the
large-scale, discrete and nonlinear optimization problems like TEP.
The effectiveness of the proposed idea is tested on an actual
transmission network of the Azerbaijan regional electric company,
Iran. The simulation results show that considering the losses even for
transmission expansion planning of a network with low load growth
is caused that operational costs decreases considerably and the
network satisfies the requirement of delivering electric power more
reliable to load centers.
Abstract: In this paper a new approach to face recognition is
presented that achieves double dimension reduction, making the
system computationally efficient with better recognition results and
out perform common DCT technique of face recognition. In pattern
recognition techniques, discriminative information of image
increases with increase in resolution to a certain extent, consequently
face recognition results change with change in face image resolution
and provide optimal results when arriving at a certain resolution
level. In the proposed model of face recognition, initially image
decimation algorithm is applied on face image for dimension
reduction to a certain resolution level which provides best
recognition results. Due to increased computational speed and feature
extraction potential of Discrete Cosine Transform (DCT), it is
applied on face image. A subset of coefficients of DCT from low to
mid frequencies that represent the face adequately and provides best
recognition results is retained. A tradeoff between decimation factor,
number of DCT coefficients retained and recognition rate with
minimum computation is obtained. Preprocessing of the image is
carried out to increase its robustness against variations in poses and
illumination level. This new model has been tested on different
databases which include ORL , Yale and EME color database.
Abstract: The overall penumbra is usually defined as the
distance, p20–80, separating the 20% and 80% of the dose on the beam axis at the depth of interest. This overall penumbra accounts
also for the fact that some photons emitted by the distal parts of the source are only partially attenuated by the collimator. Medulloblastoma is the most common type of childhood brain tumor
and often spreads to the spine. Current guidelines call for surgery to remove as much of the tumor as possible, followed by radiation of the brain and spinal cord, and finally treatment with chemotherapy.
The purpose of this paper was to present results on an Uniformity of dose distribution in radiation fields surrounding the spine using film
dosimetry and comparison with 3D treatment planning software.
Abstract: A satured liquid is warmed until boiling in a parallelepipedic boiler. The heat is supplied in a liquid through the horizontal bottom of the boiler, the other walls being adiabatic. During the process of boiling, the liquid evaporates through its free surface by deforming it. This surface which subdivides the boiler into two regions occupied on both sides by the boiled liquid (broth) and its vapor which surmounts it. The broth occupying the region and its vapor the superior region. A two- fluids model is used to describe the dynamics of the broth, its vapor and their interface. In this model, the broth is treated as a monophasic fluid (homogeneous model) and form with its vapor adiphasic pseudo fluid (two-fluid model). Furthermore, the interface is treated as a zone of mixture characterized by superficial void fraction noted α* . The aim of this article is to describe the dynamics of the interface between the boiled fluid and its vapor within a boiler. The resolution of the problem allowed us to show the evolution of the broth and the level of the liquid.