Abstract: Many water desalination technologies have been
developed but in general they are energy intensive and have high cost
and adverse environmental impact. Recently, adsorption technology
for water desalination has been investigated showing the potential of
using low temperature waste heat (50-85oC) thus reducing energy
consumption and CO2 emissions. This work mathematically
compares the performance of an adsorption cycle that produces two
useful effects namely, fresh water and cooling using two different
adsorbents, silica-gel and an advanced zeolite material AQSOA-ZO2,
produced by Mitsubishi plastics. It was found that at low chilled
water temperatures, typically below 20oC, the AQSOA-Z02 is more
efficient than silica-gel as the cycle can produce 5.8 m3 of fresh water
per day and 50.1 Rton of cooling per tonne of AQSOA-ZO2. Above
20oC silica-gel is still better as the cycle production reaches 8.4 m3
per day and 62.4 Rton per tonne of silica-gel. These results show the
potential of using the AQSOA-Z02 at low chilled water temperature
for water desalination and cooling applications.
Abstract: Al6061 alloy base matrix, reinforced with particles of
silicon carbide (10 wt %) and Graphite powder (1wt%), known as
hybrid composites have been fabricated by liquid metallurgy route
(stir casting technique) and optimized at different parameters like
applied load, sliding speed and sliding distance by taguchi method. A
plan of experiment generated through taguchi technique was used to
perform experiments based on L27 orthogonal array. The developed
ANOVA and regression equations are used to find the optimum
coefficient of friction and wear under the influence of applied load,
sliding speed and sliding distance. On the basis of “smaller the best”
the dry sliding wear resistance was analysed and finally confirmation
tests were carried out to verify the experimental results.
Abstract: This research paper presents highly optimized barrel
shifter at 22nm Hi K metal gate strained Si technology node. This
barrel shifter is having a unique combination of static and dynamic
body bias which gives lowest power delay product. This power delay
product is compared with the same circuit at same technology node
with static forward biasing at ‘supply/2’ and also with normal reverse
substrate biasing and still found to be the lowest. The power delay
product of this barrel sifter is .39362X10-17J and is lowered by
approximately 78% to reference proposed barrel shifter at 32nm bulk
CMOS technology. Power delay product of barrel shifter at 22nm Hi
K Metal gate technology with normal reverse substrate bias is
2.97186933X10-17J and can be compared with this design’s PDP of
.39362X10-17J. This design uses both static and dynamic substrate
biasing and also has approximately 96% lower power delay product
compared to only forward body biased at half of supply voltage. The
NMOS model used are predictive technology models of Arizona state
university and the simulations to be carried out using HSPICE
simulator.
Abstract: This paper investigates and compares the community
support for tourism development between two groups of minority
ethnic descendants in Malacca, Malaysia, namely the Baba-Nyonya
and Portuguese. A descriptive research design using a quantitative
method with self-reported and self-administered questionnaires
through across-sectional approach was applied. Through the
descriptive and inferential statistics, some significantly useful
insights pertaining to the issue investigated were obtained. The
research outcomes indicate that the sense of community is somewhat
more effective in small communities in terms of togetherness,
closeness and a sense of belonging compared to the slightly bigger
minority group. In addition, the sense of community attributes
through membership, influence, integration and shared emotional
connections contributes to community participation in tourism
development regardless of which ethnic group one belongs to.
Abstract: Mass media campaigns against obesity are often
designed to impact large audiences. This usually means that their
audience is defined based on general demographic characteristics like
age, gender, occupation etc., not taking into account psychographics
like behavior, motivations, wants, etc. Using psychographics, as the
base for the audience segmentation, is a common practice in case of
successful campaigns, as it allows developing more relevant
messages. It also serves a purpose of identifying key segments, those
that generate the best return on investment. For a health campaign,
that would be segments that have the best chance of being converted
into healthy lifestyle at the lowest cost. This paper presents the
limitations of the demographic targeting, based on the findings from
the reception study of IMSS (Mexican Social Security Institute) antiobesity
TV commercials and proposes mothers as the first level of
segmentation, in the process of identifying the key segment for these
campaigns.
Abstract: Fabric textures are very common in our daily life.
However, the representation of fabric textures has never been explored
from neuroscience view. Theoretical studies suggest that primary
visual cortex (V1) uses a sparse code to efficiently represent natural
images. However, how the simple cells in V1 encode the artificial
textures is still a mystery. So, here we will take fabric texture as
stimulus to study the response of independent component analysis that
is established to model the receptive field of simple cells in V1. We
choose 140 types of fabrics to get the classical fabric textures as
materials. Experiment results indicate that the receptive fields of
simple cells have obvious selectivity in orientation, frequency and
phase when drifting gratings are used to determine their tuning
properties. Additionally, the distribution of optimal orientation and
frequency shows that the patch size selected from each original fabric
image has a significant effect on the frequency selectivity.
Abstract: Purpose: The study aimed to assess the depressant or
antidepressant effects of several Nonsteroidal Anti-Inflammatory
Drugs (NSAIDs) in mice: the selective cyclooxygenase-2 (COX-2)
inhibitor meloxicam, and the non-selective COX-1 and COX-2
inhibitors lornoxicam, sodium metamizole, and ketorolac. The
current literature data regarding such effects of these agents are
scarce.
Materials and methods: The study was carried out on NMRI mice
weighing 20-35 g, kept in a standard laboratory environment. The
study was approved by the Ethics Committee of the University of
Medicine and Pharmacy „Carol Davila”, Bucharest. The study agents
were injected intraperitoneally, 10 mL/kg body weight (bw) 1 hour
before the assessment of the locomotor activity by cage testing (n=10
mice/ group) and 2 hours before the forced swimming tests (n=15).
The study agents were dissolved in normal saline (meloxicam,
sodium metamizole), ethanol 11.8% v/v in normal saline (ketorolac),
or water (lornoxicam), respectively. Negative and positive control
agents were also given (amitryptilline in the forced swimming test).
The cage floor used in the locomotor activity assessment was divided
into 20 equal 10 cm squares. The forced swimming test involved
partial immersion of the mice in cylinders (15/9cm height/diameter)
filled with water (10 cm depth at 28C), where they were left for 6
minutes. The cage endpoint used in the locomotor activity assessment
was the number of treaded squares. Four endpoints were used in the
forced swimming test (immobility latency for the entire 6 minutes,
and immobility, swimming, and climbing scores for the final 4
minutes of the swimming session), recorded by an observer that was
„blinded” to the experimental design. The statistical analysis used the
Levene test for variance homogeneity, ANOVA and post-hoc
analysis as appropriate, Tukey or Tamhane tests.
Results: No statistically significant increase or decrease in the
number of treaded squares was seen in the locomotor activity
assessment of any mice group. In the forced swimming test,
amitryptilline showed an antidepressant effect in each experiment, at
the 10 mg/kg bw dosage. Sodium metamizole was depressant at 100
mg/kg bw (increased the immobility score, p=0.049, Tamhane test),
but not in lower dosages as well (25 and 50 mg/kg bw). Ketorolac
showed an antidepressant effect at the intermediate dosage of 5
mg/kg bw, but not so in the dosages of 2.5 and 10 mg/kg bw,
respectively (increased the swimming score, p=0.012, Tamhane test).
Meloxicam and lornoxicam did not alter the forced swimming
endpoints at any dosage level.
Discussion: 1) Certain NSAIDs caused changes in the forced
swimming patterns without interfering with locomotion. 2) Sodium
metamizole showed a depressant effect, whereas ketorolac proved
antidepressant. Conclusion: NSAID-induced mood changes are not
class effects of these agents and apparently are independent of the
type of inhibited cyclooxygenase (COX-1 or COX-2).
Disclosure: This paper was co-financed from the European Social
Fund, through the Sectorial Operational Programme Human Resources Development 2007-2013, project number POSDRU /159
/1.5 /S /138907 "Excellence in scientific interdisciplinary research,
doctoral and postdoctoral, in the economic, social and medical fields
-EXCELIS", coordinator The Bucharest University of Economic
Studies.
Abstract: Advanced treatments such as forward osmosis (FO)
can be used to separate or reject nutrients from secondary treated
effluents. Forward osmosis uses the chemical potential across the
membrane, which is the osmotic pressure gradient, to induce water to
flow through the membrane from a feed solution (FS) into a draw
solution (DS). The performance of FO is affected by the membrane
characteristics, composition of the FS and DS, and operating
conditions. The aim of this study was to investigate the optimum
velocity and temperature for nutrient rejection and water flux
performance in FO treatments. MgCl2 was used as the DS in the FO
process. The results showed that higher cross flow velocities yielded
higher water fluxes. High rejection of nutrients was achieved by using
a moderate cross flow velocity at 0.25 m/s. Nutrient rejection was
insensitive to temperature variation, whereas water flux was
significantly impacted by it. A temperature of 25°C was found to be
good for nutrient rejection.
Abstract: The Orthogonal Frequency Division Multiplexing
(OFDM) with high data rate, high spectral efficiency and its ability to
mitigate the effects of multipath makes them most suitable in wireless
application. Impulsive noise distorts the OFDM transmission and
therefore methods must be investigated to suppress this noise. In this
paper, a State Space Recursive Least Square (SSRLS) algorithm
based adaptive impulsive noise suppressor for OFDM
communication system is proposed. And a comparison with another
adaptive algorithm is conducted. The state space model-dependent
recursive parameters of proposed scheme enables to achieve steady
state mean squared error (MSE), low bit error rate (BER), and faster
convergence than that of some of existing algorithm.
Abstract: Brass terminal, one of the several crude oil and
petroleum products storage/handling facilities in the Niger Delta was
built in the 1980s. Activities at this site, over the years, released
crude oil into this 3 m-deep, 1500 m-long canal lying adjacent to the
terminal with oil floating on it and its sediment heavily polluted. To
ensure effective clean-up, three major activities were planned: site
characterization, bioremediation pilot plant construction and testing
and full-scale bioremediation of contaminated sediment / bank soil by
land farming. The canal was delineated into 12 lots and each
characterized, with reference to the floating oily phase, contaminated
sediment and canal bank soil. As a result of site characterization, a
pilot plant for on-site bioremediation was designed and a treatment
basin constructed for carrying out pilot bioremediation test.
Following a designed sampling protocol, samples from this pilot
plant were collected for analysis at two laboratories as a quality
assurance / quality control check. Results showed that Brass Canal
upstream is contaminated with dark, thick and viscous oily film with
characteristic hydrocarbon smell while downstream, thin oily film
interspersed with water was observed. Sediments were observed to be
dark with mixture of brownish sandy soil with TPH ranging from
17,800 mg/kg in Lot 1 to 88,500 mg/kg in Lot 12 samples. Brass
Canal bank soil was observed to be sandy from ground surface to 3m,
below ground surface (bgs) it was silty-sandy and brownish while
subsurface soil (4-10m bgs) was sandy-clayey and whitish/grayish
with typical hydrocarbon smell. Preliminary results obtained so far
have been very promising but were proprietary. This project is
considered, to the best of technical literature knowledge, the first
large-scale on-site bioremediation project in the Niger Delta region,
Nigeria.
Abstract: The concentrations of heavy metals in sediments of
Qua Iboe River Estuary (QIRE) were monitored at four different
sampling locations in wet and dry seasons. A preliminary survey to
determine the four sampling stations along the river continuum
showed that the area spanned between
Abstract: In this paper, we propose a system for preventing gas
risks through the use of wireless communication modules and
intelligent gas safety appliances. Our system configuration consists of
an automatic extinguishing system, detectors, a wall-pad, and a
microcomputer controlled micom gas meter to monitor gas flow and
pressure as well as the occurrence of earthquakes. The automatic fire
extinguishing system checks for both combustible gaseous leaks and
monitors the environmental temperature, while the detector array
measures smoke and CO gas concentrations. Depending on detected
conditions, the micom gas meter cuts off an inner valve and generates
a warning, the automatic fire-extinguishing system cuts off an external
valve and sprays extinguishing materials, or the sensors generate
signals and take further action when smoke or CO are detected.
Information on intelligent measures taken by the gas safety appliances
and sensors are transmitted to the wall-pad, which in turn relays this as
real time data to a server that can be monitored via an external network
(BcN) connection to a web or mobile application for the management
of gas safety. To validate this smart-home gas management system, we
field-tested its suitability for use in Korean apartments under several
scenarios.
Abstract: Here, we study the characteristic feature of
conventional (ON-OFF keying) and soliton based transmission
system. We consider 20Gbps transmission system implemented with
Conventional Single Mode Fiber (C-SMF) to examine the role of
Gaussian pulse which is the characteristic of conventional
propagation and Hyperbolic-secant pulse which is the characteristic
of soliton propagation in it. We note the influence of these pulses
with respect to different dispersion lengths and soliton period in
conventional and soliton system respectively and evaluate the system
performance in terms of Quality factor. From the analysis, we could
prove that the soliton pulse has the consistent performance even for
long distance without dispersion compensation than the conventional
system as it is robust to dispersion. For the length of transmission of
200Km, soliton system yielded Q of 33.958 while the conventional
system totally exhausted with Q=0.
Abstract: Microstructural and hardening changes of
Fe-0.2wt.%V alloy and pure Fe irradiated with 100 keV hydrogen ions
at room temperature were investigated. It was found that dislocation
density varies dramatically after irradiation, ranging from dislocation
free to dense areas with tangled and complex dislocation
configuration. As the irradiated Fe-0.2wt.%V samples were annealed
at 773 K, the irradiation-induced dislocation loops disappear, while
many small precipitates with enriched C distribute in the matrix. Some
large precipitates with enriched V were also observed. The hardness of
Fe-0.2wt.%V alloy and pure Fe increases after irradiation, which
ascribes to the formation of dislocation loops in the irradiated
specimens. Compared with pure Fe, the size of the
irradiation-introduced dislocation loops in Fe-0.2wt.%V alloy
decreases and the density increases, the change of the hardness also
decreases.
Abstract: Phthalates are ubiquitous environmental pollutants
well known because of their endocrine disrupting activity in human
organism. The aim of our study was, by biological monitoring,
investigate exposure to phthalates of Roma ethnicity group i.e.
children and adults from 5 families (n=29, average age 11.8 ± 7.6
years) living in western Slovakia. Additionally, we analysed some
associations between anthropometric measures, questionnaire data
i.e. socio-economic status, eating and drinking habits, practise of
personal care products and household conditions in comparison with
concentrations of phthalate metabolites. We used for analysis of urine
samples high performance liquid chromatography and tandem mass
spectrometry (HPLC-MS/MS) to determine concentrations of
phthalate metabolites monoethyl phthalate (MEP), mono-n-butyl
phthalate (MnBP), mono-iso-butyl phthalate (MiBP), mono(2-ethyl-
5-hydroxyhexyl) phthalate (5OH-MEHP), mono(2-ethyl-5-oxohexyl)
phthalate (5oxo-MEHP) and mono(2-etylhexyl) phthalate (MEHP).
Our results indicate that ethnicity, lower socioeconomic status and
different housing conditions in Roma population can affect urinary
concentration of phthalate metabolites.
Abstract: The separation of Hg (II) from produced water by
hollow fiber contactors (HFC) was investigation. This system
included of two hollow fiber modules in the series connecting. The
first module used for the extraction reaction and the second module
for stripping reaction. Aliquat336 extractant was fed from the organic
reservoirs into the shell side of the first hollow fiber module and
continuous to the shell side of the second module. The organic liquid
was continuously feed recirculate and back to the reservoirs. The feed
solution was pumped into the lumen (tube side) of the first hollow
fiber module. Simultaneously, the stripping solution was pumped in
the same way in tube side of the second module. The feed and
stripping solution was fed which had a countercurrent flow. Samples
were kept in the outlet of feed and stripping solution at 1 hour and
characterized concentration of Hg (II) by Inductively Couple Plasma
Atomic Emission Spectroscopy (ICP-AES). Feed solution was
produced water from natural gulf of Thailand. The extractant was
Aliquat336 dissolved in kerosene diluent. Stripping solution used was
nitric acid (HNO3) and thiourea (NH2CSNH2). The effect of carrier
concentration and type of stripping solution were investigated.
Results showed that the best condition were 10 % (v/v) Aliquat336
and 1.0 M NH2CSNH2. At the optimum condition, the extraction and
stripping of Hg (II) were 98% and 44.2%, respectively.
Abstract: This paper examines the utilization of public-private
partnerships for the building and operation of wastewater treatment
plants. Our research focuses on risk allocation in this kind of projects.
Our analysis builds on more than hundred wastewater treatment
plants built and operated through PPP projects in Aragon (Spain).
The paper illustrates the consequences of an inadequate management
of construction risk and an unsuitable transfer of demand risk in
wastewater treatment plants. It also shows that the involvement of
many public bodies at local, regional and national level further
increases the complexity of this kind of projects and make time
delays more likely.
Abstract: To understand the friction stir welding process, it is
very important to know the nature of the material flow in and around
the tool. The process is a combination of both thermal as well as
mechanical work i.e. it is a coupled thermo-mechanical process.
Numerical simulations are very much essential in order to obtain a
complete knowledge of the process as well as the physics underlying
it. In the present work a model based approach is adopted in order to
study material flow. A thermo-mechanical based CFD model is
developed using a Finite Element package, Comsol Multiphysics.
The fluid flow analysis is done. The model simultaneously predicts
shear strain fields, shear strain rates and shear stress over the entire
workpiece for the given conditions. The flow fields generated by the
streamline plot give an idea of the material flow. The variation of
dynamic viscosity, velocity field and shear strain fields with various
welding parameters is studied. Finally the result obtained from the
above mentioned conditions is discussed elaborately and concluded.
Abstract: The polymer foil used for manufacturing of
laminated glass members behaves in a viscoelastic manner with
temperature dependance. This contribution aims at incorporating
the time/temperature-dependent behavior of interlayer to our earlier
elastic finite element model for laminated glass beams. The model
is based on a refined beam theory: each layer behaves according
to the finite-strain shear deformable formulation by Reissner and
the adjacent layers are connected via the Lagrange multipliers
ensuring the inter-layer compatibility of a laminated unit. The
time/temperature-dependent behavior of the interlayer is accounted
for by the generalized Maxwell model and by the time-temperature
superposition principle due to the Williams, Landel, and Ferry.
The resulting system is solved by the Newton method with
consistent linearization and the viscoelastic response is determined
incrementally by the exponential algorithm. By comparing the model
predictions against available experimental data, we demonstrate that
the proposed formulation is reliable and accurately reproduces the
behavior of the laminated glass units.
Abstract: This paper presents a rank correlation curve. The
traditional correlation coefficient is valid for both continuous
variables and for integer variables using rank statistics. Since
the correlation coefficient has already been established in rank
statistics by Spearman, such a calculation can be extended to
the correlation curve.
This paper presents two survey questions. The survey
collected non-continuous variables. We will show weak to
moderate correlation. Obviously, one question has a negative
effect on the other. A review of the qualitative literature
can answer which question and why. The rank correlation
curve shows which collection of responses has a positive
slope and which collection of responses has a negative slope.
Such information is unavailable from the flat, ”first-glance”
correlation statistics.