Abstract: Terminal localization for indoor Wireless Local Area
Networks (WLANs) is critical for the deployment of location-aware
computing inside of buildings. A major challenge is obtaining high
localization accuracy in presence of fluctuations of the received signal
strength (RSS) measurements caused by multipath fading. This paper
focuses on reducing the effect of the distance-varying noise by spatial
filtering of the measured RSS. Two different survey point geometries
are tested with the noise reduction technique: survey points arranged
in sets of clusters and survey points uniformly distributed over the
network area. The results show that the location accuracy improves
by 16% when the filter is used and by 18% when the filter is applied
to a clustered survey set as opposed to a straight-line survey set.
The estimated locations are within 2 m of the true location, which
indicates that clustering the survey points provides better localization
accuracy due to superior noise removal.
Abstract: The study of piezoelectric material in the past was in T-Domain form; however, no one has studied piezoelectric material in the S-Domain form. This paper will present the piezoelectric material in the transfer function or S-Domain model. S-Domain is a well known mathematical model, used for analyzing the stability of the material and determining the stability limits. By using S-Domain in testing stability of piezoelectric material, it will provide a new tool for the scientific world to study this material in various forms.
Abstract: In this paper, the problem of reducing switching
activity in on-chip buses at the stage of high-level synthesis is
considered, and a high-level low power bus binding based on dynamic
bit reordering is proposed. Whereas conventional methods use a fixed
bit ordering between variables within a bus, the proposed method
switches a bit ordering dynamically to obtain a switching activity
reduction. As a result, the proposed method finds a binding solution
with a smaller value of total switching activity (TSA). Experimental
result shows that the proposed method obtains a binding solution
having 12.0-34.9% smaller TSA compared with the conventional
methods.
Abstract: This paper presents a low cost automatic system for
sampling the electric field in a limited area. The scanning area is a
flat surface parallel to the ground at a selected height. We discuss
in detail the hardware, software and all the arrangements involved
in the system operation. In order to show the system performance
we include a campaign of narrow band measurements with 6017
sample points in the surroundings of a cellular base station. A
commercial isotropic antenna with three orthogonal axes was used
as sampling device. The results are analyzed in terms of its space
average, standard deviation and statistical distribution.
Abstract: This paper presents positive and negative full-wave
rectifier. The proposed structure is based on OTA using
commercially available ICs (LT1228). The features of the proposed
circuit are that: it can rectify and amplify voltage signal with
controllable output magnitude via input bias current: the output
voltage is free from temperature variation. The circuit description
merely consists of 1 single ended and 3 fully differential OTAs. The
performance of the proposed circuit are investigated though PSpice.
They show that the proposed circuit can function as positive/negative
full-wave rectifier, where the voltage input wide-dynamic range from
-5V to 5V. Furthermore, the output voltage is slightly dependent on
the temperature variations.
Abstract: Smith Predictor control is theoretically a good solution to the problem of controlling the time delay systems. However, it seldom gets use because it is almost impossible to find out a precise mathematical model of the practical system and very sensitive to uncertain system with variable time-delay. In this paper is concerned with a design method of smith predictor for temperature control system by Coefficient Diagram Method (CDM). The simulation results show that the control system with smith predictor design by CDM is stable and robust whilst giving the desired time domain system performance.
Abstract: This paper presents an application of 5S lean technology to a production facility. Due to increased demand, high product variety, and a push production system, the plant has suffered from excessive wastes, unorganized workstations, and unhealthy work environment. This has translated into increased production cost, frequent delays, and low workers morale. Under such conditions, it has become difficult, if not impossible, to implement effective continuous improvement studies. Hence, the lean project is aimed at diagnosing the production process, streamlining the workflow, removing/reducing process waste, cleaning the production environment, improving plant layout, and organizing workstations. 5S lean technology is utilized for achieving project objectives. The work was a combination of both culture changes and tangible/physical changes on the shop floor. The project has drastically changed the plant and developed the infrastructure for a successful implementation of continuous improvement as well as other best practices and quality initiatives.
Abstract: With major technological advances and to reduce the
cost of training apprentices for real-time critical systems, it was
necessary the development of Intelligent Tutoring Systems for
training apprentices in these systems. These systems, in general, have
interactive features so that the learning is actually more efficient,
making the learner more familiar with the mechanism in question. In
the home stage of learning, tests are performed to obtain the student's
income, a measure on their use. The aim of this paper is to present a
framework to model an Intelligent Tutoring Systems using the UML
language. The various steps of the analysis are considered the
diagrams required to build a general model, whose purpose is to
present the different perspectives of its development.
Abstract: A study was undertaken to assess the potential of an
Algal Turf Scrubber to remove nitrogen from aquaculture effluent to
reduce environmental pollution. High total ammonia nitrogen
concentrations were introduced to an Algal Turf Scrubber developed
under varying hydraulic surface loading rates of African catfish
(Clarius gariepinus) effluent in a recirculating aquaculture system.
Nutrient removal rates were not affected at total suspended solids
concentration of up to 0.04g TSS/l (P > 0.05). Nitrogen removal
rates 0.93-0.99g TAN/m²/d were recorded at very high loading rates
3.76-3.81 g TAN/m²/d. Total ammonia removal showed ½ order
kinetics between 1.6 to 2.3mg/l Total Ammonia Nitrogen
concentrations. Nitrogen removal increased with its loading, which
increased with hydraulic surface loading rate. Total Ammonia
Nitrogen removal by Algal turf scrubber was higher than reported
values for fluidized bed filters and trickling filters. The algal turf
scrubber also effectively removed nitrate thereby reducing the need
for water exchange.
Abstract: Information regarding early onset neonatal sepsis
(EONS) pathogens may vary between regions. Global perspectives
showed Group B Streptococcal (GBS) as the most common causative
pathogens, but the widespread use of intrapartum antibiotics has
changed the pathogens pattern towards gram negative
microorganisms, especially E. coli. Objective of this study is to
describe the pathogens isolated, to assess current treatment and risk
of EONS. Records of 899 neonates born in three General Hospitals
between 2009 until 2012 were retrospectively reviewed. Proven was
found in 22 (3%) neonates. The majority was isolated with gram
positive organisms, 17 (2.3%). All grams positive and most gram
negative organisms showed sensitivity to the tested antibiotics. Only
two rare gram negative organisms showed total resistant. Male was
possible risk of proven EONS. Although proven EONS remains
uncommon in Malaysia, nonetheless, the effect of intrapartum
antibiotics still required continuous surveillance.
Abstract: There is an urgent need to develop novel
Mycobacterium tuberculosis (Mtb) drugs that are active against drug
resistant bacteria but, more importantly, kill persistent bacteria. Our
study structured based on integrated analysis of metabolic pathways,
small molecule screening and similarity Search in PubChem
Database. Metabolic analysis approaches based on Unified weighted
used for potent target selection. Our results suggest that pantothenate
synthetase (panC) and and 3-methyl-2-oxobutanoate hydroxymethyl
transferase (panB) as a appropriate drug targets. In our study, we
used pantothenate synthetase because of existence inhibitors. We
have reported the discovery of new antitubercular compounds
through ligand based approaches using computational tools.
Abstract: This paper attempts to establish the fact that Multi
State Network Classification is essential for performance
enhancement of Transport protocols over Satellite based Networks. A
model to classify Multi State network condition taking into
consideration both congestion and channel error is evolved. In order
to arrive at such a model an analysis of the impact of congestion and
channel error on RTT values has been carried out using ns2. The
analysis results are also reported in the paper. The inference drawn
from this analysis is used to develop a novel statistical RTT based
model for multi state network classification.
An Adaptive Multi State Proactive Transport Protocol consisting
of Proactive Slow Start, State based Error Recovery, Timeout Action
and Proactive Reduction is proposed which uses the multi state
network state classification model. This paper also confirms through
detail simulation and analysis that a prior knowledge about the
overall characteristics of the network helps in enhancing the
performance of the protocol over satellite channel which is
significantly affected due to channel noise and congestion.
The necessary augmentation of ns2 simulator is done for
simulating the multi state network classification logic. This
simulation has been used in detail evaluation of the protocol under
varied levels of congestion and channel noise. The performance
enhancement of this protocol with reference to established protocols
namely TCP SACK and Vegas has been discussed. The results as
discussed in this paper clearly reveal that the proposed protocol
always outperforms its peers and show a significant improvement in
very high error conditions as envisaged in the design of the protocol.
Abstract: Due to the deregulation of the Electric Supply
Industry and the resulting emergence of electricity market, the
volumes of power purchases are on the rise all over the world. In a
bid to meet the customer-s demand in a reliable and yet economic
manner, utilities purchase power from the energy market over and
above its own production. This paper aims at developing an optimal
power purchase model with two objectives viz economy and
environment ,taking various functional operating constraints such as
branch flow limits, load bus voltage magnitudes limits, unit capacity
constraints and security constraints into consideration.The price of
purchased power being an uncertain variable is modeled using fuzzy
logic. DEMO (Differential Evolution For Multi-objective
Optimization) is used to obtain the pareto-optimal solution set of the
multi-objective problem formulated. Fuzzy set theory has been
employed to extract the best compromise non-dominated solution.
The results obtained on IEEE 30 bus system are presented and
compared with that of NSGAII.
Abstract: Urban non-point source (NPS) pollution for a
residential catchment in Miri, Sarawak was investigated for two storm events in 2011. Runoff from two storm events were sampled and tested for water quality parameters including TSS, BOD5, COD,
NH3-N, NO3-N, NO2-N, P and Pb. Concentration of the water quality
parameters was found to vary significantly between storms and the pollutant of concern was found to be NO3-N, TSS, COD and Pb. Results were compared to the Interim National Water Quality
Standards for Malaysia (INWQS),and the stormwater runoff from the
study can be classified as polluted, exceeding class III water quality,
especially in terms of TSS, COD, and NH3-N with maximum EMCs
of 158, 135, and 2.17 mg/L, respectively.
Abstract: The model-based approach to user interface design relies on developing separate models that are capturing various aspects about users, tasks, application domain, presentation and dialog representations. This paper presents a task modeling approach for user interface design and aims at exploring the mappings between task, domain and presentation models. The basic idea of our approach is to identify typical configurations in task and domain models and to investigate how they relate each other. A special emphasis is put on application-specific functions and mappings between domain objects and operational task structures. In this respect, we will distinguish between three layers in the task decomposition: a functional layer, a planning layer, and an operational layer.
Abstract: This paper describes a complex energy signal model
that is isomorphic with digital human fingerprint images. By using
signal models, the problem of fingerprint matching is transformed
into the signal processing problem of finding a correlation between
two complex signals that differ by phase-rotation and time-scaling. A
technique for minutiae matching that is independent of image
translation, rotation and linear-scaling, and is resistant to missing
minutiae is proposed. The method was tested using random data
points. The results show that for matching prints the scaling and
rotation angles are closely estimated and a stronger match will have a
higher correlation.
Abstract: Macrobenthos distribution along the coastal waters of
Penang National Park was studid to estimate the effect of different
environmental parameters at three stations, during six sampling
months, from June 2010 to April 2011. The aim of this survey was to
investigate different environment stress over soft bottom polychaete
community along Teluk Ketapang and Pantai Acheh (Penang
National Park) over a year period. Variations in the polychaete
community were evaluated using univariate and multivariate
methods. A total of 604 individuals were examined which was
grouped into 23 families. Family Nereidae was the most abundant
(22.68%), followed by Spionidae (22.02%), Hesionidae (12.58%),
Nephtylidae (9.27%) and Orbiniidae (8.61%). It is noticeable that
good results can only be obtained on the basis of good taxonomic
resolution. The maximum Shannon-Wiener diversity (H'=2.16) was
recorded at distance 200m and 1200m (August 2010) in Teluk
Ketapang and lowest value of diversity was found at distance 1200m
(December 2010) in Teluk Ketapang.
Abstract: Nowadays, hard disk is one of the most popular storage components. In hard disk industry, the hard disk drive must pass various complex processes and tested systems. In each step, there are some failures. To reduce waste from these failures, we must find the root cause of those failures. Conventionall data analysis method is not effective enough to analyze the large capacity of data. In this paper, we proposed the Hough method for straight line detection that helps to detect straight line defect patterns that occurs in hard disk drive. The proposed method will help to increase more speed and accuracy in failure analysis.
Abstract: Steel corrosion in concrete is considered as a main
engineering problems for many countries and lots of expenses has been paid for their repair and maintenance annually. This problem
may occur in all engineering structures whether in coastal and offshore or other areas. Hence, concrete structures should be able to
withstand corrosion factors existing in water or soil. Reinforcing
steel corrosion enhancement can be measured by use of concrete
electrical resistance; and maintaining high electric resistivity in concrete is necessary for steel corrosion prevention. Lots of studies
devoted to different aspects of the subjects worldwide. In this paper, an evaluation of the effects of W/C ratio, cementitious materials, and
percent increase in silica fume were investigated on electric resistivity of high strength concrete. To do that, sixteen mix design
with one aggregate grading was planned. Five of them had varying amount of W/C ratio and other eleven mixes was prepared with
constant W/C ratio but different amount of cementitious materials.
Silica fume and super plasticizer were used with different proportions
in all specimens. Specimens were tested after moist curing for 28 days. A total of 80 cube specimens (50 mm) were tested for concrete
electrical resistance. Results show that concrete electric resistivity can be increased with increasing amount of cementitious materials
and silica fume.
Abstract: A specially designed flat plate was mounted vertically
over the axial line in the wind tunnel of the Aerospace Department of
the Pusan National University. The plate is 2 m long, 0.8 m high and 8
cm thick. The measurements were performed in velocity range from
15 to 60 m/s. A sand paper turbulizer was placed close to the plate nose
to provide fully developed turbulent boundary layer over the most part
of the plate. Strain balances were mounted in the trailing part of the
plate to measure the skin friction drag over removable insertions of
0.55×0.25m2 size. A set of the insertions was designed and
manufactured: 3mm thick polished metal surface and three compliant
surfaces. The compliant surfaces were manufactured of a silicone
rubber Silastic® S2 (Dow Corning company). To modify the
viscoelastic properties of the rubber, its composition was varied: 90%
of the rubber + 10% catalyst (standard), 92.5% + 7.5% (weak), 85% +
15% (strong). Modulus of elasticity and the loss tangent were
measured accurately for these materials in the frequency range from
40 Hz to 3 KHz using the unique proposed technique.