Abstract: The importance of energy efficiency within the production processes increases steadily. For a comprehensive assessment of energy efficiency within the production process, unfortunately no tools exist or have been developed yet. Therefore the Institute for Factory Automation and Production Systems at the Friedrich-Alexander-University Erlangen-Nuremberg has developed two methods with the goal of achieving transparency and a quantitative assessment of energy efficiency namely EEV (Energy Efficiency Value) and EPE (Energetic Process Efficiency). This paper describes the basics and state-of-the-art as well as the developed approaches.
Abstract: A multilayer passive shield composed of low-activity
lead (Pb), copper (Cu), tin (Sn) and iron (Fe) was designed and
manufactured for a coaxial HPGe detector placed at a surface
laboratory for reducing background radiation and radiation dose to
the personnel. The performance of the shield was evaluated and
efficiency curves of the detector were plotted by using of various
standard sources in different distances. Monte Carlo simulations and
a set of TLD chips were used for dose estimation in two distances of
20 and 40 cm. The results show that the shield reduced background
spectrum and the personnel dose more than 95%.
Abstract: The paper identifies the features of Polish sports clubs
in the particular organizational forms: profit and nonprofit.
Identification and description of these features is carried out in terms
of financial efficiency of the given organizational form. Under the
terms of the efficiency the research allows you to specify the
advantages of particular organizational sports club form and the
following limitations. Paper considers features of sports clubs in
range of Polish conditions as legal regulations. The sources of the
functioning efficiency of sports clubs may lie in the organizational
forms in which they operate. Each of the available forms can be
considered either a for-profit or nonprofit enterprise. Depending on
this classification there are different capabilities of increasing
organizational and financial efficiency of a given sports club. Authors
start with general classification and difference between for-profit and
non-profit sport clubs. Next identifies specific financial and
organizational conditions of both organizational form and then show
examples of mixed activity forms and their efficiency effect.
Abstract: The present paper attempts to investigate the
prediction of air entrainment rate and aeration efficiency of a free
overfall jets issuing from a triangular sharp crested weir by using
regression based modelling. The empirical equations, Support vector
machine (polynomial and radial basis function) models and the linear
regression techniques were applied on the triangular sharp crested
weirs relating the air entrainment rate and the aeration efficiency to
the input parameters namely drop height, discharge, and vertex angle.
It was observed that there exists a good agreement between the
measured values and the values obtained using empirical equations,
Support vector machine (Polynomial and rbf) models and the linear
regression techniques. The test results demonstrated that the SVM
based (Poly & rbf) model also provided acceptable prediction of the
measured values with reasonable accuracy along with empirical
equations and linear regression techniques in modelling the air
entrainment rate and the aeration efficiency of a free overfall jets
issuing from triangular sharp crested weir. Further sensitivity analysis
has also been performed to study the impact of input parameter on the
output in terms of air entrainment rate and aeration efficiency.
Abstract: Automation of airport operations can greatly improve
ground movement efficiency. In this paper, we study the speed profile
design problem for advanced airport ground movement control and
guidance. The problem is constrained by the surface four-dimensional
trajectory generated in taxi planning. A decomposed approach of two
stages is presented to solve this problem efficiently. In the first stage,
speeds are allocated at control points, which ensure smooth speed
profiles can be found later. In the second stage, detailed speed profiles
of each taxi interval are generated according to the allocated control
point speeds with the objective of minimizing the overall fuel
consumption. We present a swarm intelligence based algorithm for the
first-stage problem and a discrete variable driven enumeration method
for the second-stage problem, since it only has a small set of discrete
variables. Experimental results demonstrate the presented
methodology performs well on real world speed profile design
problems.
Abstract: In order to achieve high data rate and increase the
spectral efficiency, multiple input multiple output (MIMO) system has
been proposed. However, multiple antennas are limited by size and
cost. Therefore, recently developed cooperative diversity scheme,
which profits the transmit diversity only with the existing hardware by
constituting a virtual antenna array, can be a solution. However, most
of the introduced cooperative techniques have a common fault of
decreased transmission rate because the destination should receive the
decodable compositions of symbols from the source and the relay. In
this paper, we propose a cooperative cyclic delay diversity (CDD)
scheme that use hierarchical modulation. This scheme is free from the
rate loss and allows seamless cooperative communication.
Abstract: The objective of this study was to evaluate the
effects of calving season on the production and economic efficiency
of dairy farms in Egypt. Our study was performed at dairy
production farms in the Alexandria, Behera, and Kafr El-Sheikh
provinces of Egypt from summer 2010 to winter 2013. The
randomly selected dairy farms had herds consisting of Baladi,
Holstein-Friesian, or cross-bred (Baladi × Holstein-Friesian) cows.
The data were collected from production records and responses to a
structured questionnaire. The average total return differed
significantly (P < 0.05) between the different cattle breeds and
calving seasons. The average total return was highest for the
Holstein- Friesian cows that calved in the winter (29106.42
EGP/cow/year), and it was lowest for Baladi cows that calved in the
summer (12489.79 EGP/cow/year). Differences in total returns
between the cows that calved in the winter or summer or between
the foreign and native breeds, as well as variations in calf prices,
might have contributed to the differences in milk yield. The average
net profit per cow differed significantly (P < 0.05) between the cattle
breeds and calving seasons. The average net profit values for the
Baladi cows that calved in the winter or summer were 2413 and
2994.96 EGP/cow/year, respectively, and those for the Holstein-
Friesian cows were 10744.17 and 7860.56 EGP/cow/year,
respectively, whereas those for the cross-bred cows were 10174.86
and 7571.33 EGP/cow/year, respectively. The variations in net profit
might have resulted from variation in the availability or price of feed
materials, milk prices, or sales volumes. Our results show that the
breed and calving season of dairy cows significantly affected the
economic efficiency of dairy farms in Egypt. The cows that calved
in the winter produced more milk than those that calved in the
summer, which may have been the result of seasonal influences,
such as temperature, humidity, management practices, and the type
of feed or green fodder available.
Abstract: Below-knee amputees commonly experience
asymmetrical gait patterns. It is generally believed that ischemia is
related to the formation of pressure sores due to uneven distribution
of forces. Micro-vascular responses can reveal local malnutrition.
Changes in local skin blood supply under various external loading
conditions have been studied for a number of years. Radionuclide
clearance, photo-plethysmography, trans-cutaneous oxygen tension
along with other studies showed that the blood supply would be
influenced by the epidermal forces, and the rate and the amount of
blood supply would decrease with increased epidermal loads being
shear forces or normal forces. Several cases of socket designs were
investigated using Finite Element Model (FEM) and Design of
Experiment (DOE) to increase flexibility and minimize the pressure
at the limb/socket interface using ultra high molecular weight
polyethylene (UHMWPE) and polyamide 6 (PA6) or Duraform. The
pressure reliefs at designated areas where reducing thickness is
involved are seen to be critical in determination of amputees’ comfort
and are very important to clinical applications. Implementing a hole
between the Patellar Tendon (PT) and Distal Tibia (DT) would
decrease stiffness and increase prosthesis range of motion where
flexibility is needed. In addition, displacement and prosthetic energy
storage increased without compromising mechanical efficiency and
prosthetic design integrity.
Abstract: This work is on decision tree-based classification for
the disbursement of scholarship. Tree-based data mining
classification technique is used in other to determine the generic rule
to be used to disburse the scholarship. The system based on the
defined rules from the tree is able to determine the class (status) to
which an applicant shall belong whether Granted or Not Granted. The
applicants that fall to the class of granted denote a successful
acquirement of scholarship while those in not granted class are
unsuccessful in the scheme. An algorithm that can be used to classify
the applicants based on the rules from tree-based classification was
also developed. The tree-based classification is adopted because of its
efficiency, effectiveness, and easy to comprehend features. The
system was tested with the data of National Information Technology
Development Agency (NITDA) Abuja, a Parastatal of Federal
Ministry of Communication Technology that is mandated to develop
and regulate information technology in Nigeria. The system was
found working according to the specification. It is therefore
recommended for all scholarship disbursement organizations.
Abstract: Batch production plants provide a wide range of
scheduling problems. In pharmaceutical industries a batch process
is usually described by a recipe, consisting of an ordering of tasks
to produce the desired product. In this research work we focused
on pharmaceutical production processes requiring the culture of
a microorganism population (i.e. bacteria, yeasts or antibiotics).
Several sources of uncertainty may influence the yield of the culture
processes, including (i) low performance and quality of the cultured
microorganism population or (ii) microbial contamination. For
these reasons, robustness is a valuable property for the considered
application context. In particular, a robust schedule will not collapse
immediately when a cell of microorganisms has to be thrown away
due to a microbial contamination. Indeed, a robust schedule should
change locally in small proportions and the overall performance
measure (i.e. makespan, lateness) should change a little if at all.
In this research work we formulated a constraint programming
optimization (COP) model for the robust planning of antibiotics
production. We developed a discrete-time model with a multi-criteria
objective, ordering the different criteria and performing a
lexicographic optimization. A feasible solution of the proposed
COP model is a schedule of a given set of tasks onto available
resources. The schedule has to satisfy tasks precedence constraints,
resource capacity constraints and time constraints. In particular
time constraints model tasks duedates and resource availability
time windows constraints. To improve the schedule robustness, we
modeled the concept of (a, b) super-solutions, where (a, b) are input
parameters of the COP model. An (a, b) super-solution is one in
which if a variables (i.e. the completion times of a culture tasks)
lose their values (i.e. cultures are contaminated), the solution can be
repaired by assigning these variables values with a new values (i.e.
the completion times of a backup culture tasks) and at most b other
variables (i.e. delaying the completion of at most b other tasks).
The efficiency and applicability of the proposed model is
demonstrated by solving instances taken from a real-life
pharmaceutical company. Computational results showed that
the determined super-solutions are near-optimal.
Abstract: The nickel-manganese (Ni-Mn) alloy coating prepared
from DC electrodeposition process in sulphamate bath was studied.
The effects of process parameters, such as current density and
electrolyte composition, on the cathodic current efficiency,
microstructure, internal stress and mechanical properties were
investigated. Because of its crucial effect on the application to the
electroforming of microelectronic components, the development of
low internal stress coating with high leveling power was emphasized.
It was found that both the coating’s manganese content and the
cathodic current efficiency increased with the raise in current density.
In addition, the internal stress of the deposited coating showed
compressive nature at low current densities while changed to tensile
one at higher current densities. Moreover, the metallographic
observation, X-ray diffraction measurement, and polarization curve
measurement were conducted. It was found that the Ni-Mn coating
consisted of nano-sized columnar grains and the maximum hardness of
the coating was associated with (111) preferred orientation in the
microstructure. The grain size was refined along with the increase in
the manganese content of the coating, which accordingly, raised its
hardness and resistance to annealing softening. In summary, the
Ni-Mn coating prepared at lower current density of 1-2 A/dm2 had low
internal stress, high leveling power, and better corrosion resistance.
Abstract: Sewer deposits have been identified as a major cause
of dysfunctions in combined sewer systems regarding sewer
management, which induces different negative consequents resulting
in poor hydraulic conveyance, environmental damages as well as
worker’s health. In order to overcome the problematics of
sedimentation, flushing has been considered as the most operative
and cost-effective way to minimize the sediments impacts and
prevent such challenges. Flushing, by prompting turbulent wave
effects, can modify the bed form depending on the hydraulic
properties and geometrical characteristics of the conduit. So far, the
dynamics of the bed-load during high-flow events in combined sewer
systems as a complex environment is not well understood, mostly due
to lack of measuring devices capable to work in the “hostile” in
combined sewer system correctly. In this regards, a one-episode
flushing issue from an opening gate valve with weir function was
carried out in a trunk sewer in Paris to understand its cleansing
efficiency on the sediments (thickness: 0-30 cm). During more than
1h of flushing within 5 m distance in downstream of this flushing
device, a maximum flowrate and a maximum level of water have
been recorded at 5 m in downstream of the gate as 4.1 m3/s and 2.1
m respectively. This paper is aimed to evaluate the efficiency of this
type of gate for around 1.1 km (from the point -50 m to +1050 m in
downstream from the gate) by (i) determining bed grain-size
distribution and sediments evolution through the sewer channel, as
well as their organic matter content, and (ii) identifying sections that
exhibit more changes in their texture after the flush. For the first one,
two series of sampling were taken from the sewer length and then
analyzed in laboratory, one before flushing and second after, at same
points among the sewer channel. Hence, a non-intrusive sampling
instrument has undertaken to extract the sediments smaller than the
fine gravels. The comparison between sediments texture after the
flush operation and the initial state, revealed the most modified zones
by the flush effect, regarding the sewer invert slope and hydraulic
parameters in the zone up to 400 m from the gate. At this distance,
despite the increase of sediment grain-size rages, D50 (median grainsize)
varies between 0.6 mm and 1.1 mm compared to 0.8 mm and 10
mm before and after flushing, respectively. Overall, regarding the
sewer channel invert slope, results indicate that grains smaller than
sands (< 2 mm) are more transported to downstream along about 400
m from the gate: in average 69% before against 38% after the flush
with more dispersion of grain-sizes distributions. Furthermore, high
effect of the channel bed irregularities on the bed material evolution
has been observed after the flush.
Abstract: This study aims to investigate the mixing behaviors of
deionized (DI) water and carboxymethyl cellulose (CMC) solutions in
C-shaped serpentine micromixers over a wide range of flow
conditions. The flow of CMC solutions exhibits shear-thinning
behaviors. Numerical simulations are performed to investigate the
effects of the mean flow speed, fluid properties and geometry
parameters on flow and mixing in the micromixers with the serpentine
channel of the same overall channel length. From the results, we can
find the following trends. When convection dominates fluid mixing,
the curvature-induced vortices enhance fluid mixing effectively. The
mixing efficiency of a micromixer consisting of semicircular C-shaped
repeating units with a smaller centerline radius is better than that of a
micromixer consisting of major segment repeating units with a larger
centerline radius. The viscosity of DI water is less than the overall
average apparent viscosity of CMC solutions, and so the effect of
curvature-induced vortices on fluid mixing in DI water is larger than
that in CMC solutions for the cases with the same mean flow speed.
Abstract: Barley (Hordeum vulgare L.), vetch (Vicia villosa),
and grass pea (Lathyrus sativus L.) monocultures as well as mixtures
of barley with each of the above legumes, in three seeding ratios (i.e.,
barley: legume 75:25, 50:50 and 25:75, based on seed numbers) were
used to investigated forage yield and competition indices. The results
showed that intercropping reduced the dry matter yield of the three
component plants, compared with their respective monocrops. The
greatest value of total dry matter yield was obtained from barley25-
grasspea75 (5.44 t ha-1) mixture, followed by grass pea sole crop (4.99
t ha-1). The total actual yield loss (AYL) values were positive and
greater than 0 in all mixtures, indicating an advantage from
intercropping over sole crops. Intercropped barley had a higher
relative crowding coefficient (K=1.64) than intercropped legumes
(K=1.20), indicating that barley was more competitive than legumes
in mixtures. Furthermore, grass pea was more competitive than vetch
in mixtures with barley. The highest land equivalent ratio (LER),
system productivity index (SPI) and monetary advantage index
(MAI) were obtained when barley was mixed at a rate of 25% with
75% seed rate of grass pea. It is concluded that intercropping of
barley with grass pea has a good potential to improve the
performance of forage with high land-use efficiency.
Abstract: In order to obtain efficient pollutants removal in
small-scale wastewater treatment plants, uniform water flow has to be
achieved. The experimental setup, designed for treating high-load
wastewater (leachate), consists of two aerobic biological reactors and
a lamellar settler. Both biological tanks were aerated by using three
different types of aeration systems - perforated pipes, membrane air
diffusers and tube ceramic diffusers. The possibility of homogenizing
the water mass with each of the air diffusion systems was evaluated
comparatively. The oxygen concentration was determined by optical
sensors with data logging. The experimental data was analyzed
comparatively for all three different air dispersion systems aiming to
identify the oxygen concentration variation during different
operational conditions. The Oxygenation Capacity was calculated for
each of the three systems and used as performance and selection
parameter. The global mass transfer coefficients were also evaluated
as important tools in designing the aeration system. Even though
using the tubular porous diffusers leads to higher oxygen
concentration compared to the perforated pipe system (which
provides medium-sized bubbles in the aqueous solution), it doesn’t
achieve the threshold limit of 80% oxygen saturation in less than 30
minutes. The study has shown that the optimal solution for the
studied configuration was the radial air diffusers which ensure an
oxygen saturation of 80% in 20 minutes. An increment of the values
was identified when the air flow was increased.
Abstract: An approach was evaluated for the retrieval of soil
moisture of bare soil surface using bistatic scatterometer data in the
angular range of 200 to 700 at VV- and HH- polarization. The
microwave data was acquired by specially designed X-band (10
GHz) bistatic scatterometer. The linear regression analysis was done
between scattering coefficients and soil moisture content to select the
suitable incidence angle for retrieval of soil moisture content. The 250
incidence angle was found more suitable. The support vector
regression analysis was used to approximate the function described
by the input output relationship between the scattering coefficient and
corresponding measured values of the soil moisture content. The
performance of support vector regression algorithm was evaluated by
comparing the observed and the estimated soil moisture content by
statistical performance indices %Bias, root mean squared error
(RMSE) and Nash-Sutcliffe Efficiency (NSE). The values of %Bias,
root mean squared error (RMSE) and Nash-Sutcliffe Efficiency
(NSE) were found 2.9451, 1.0986 and 0.9214 respectively at HHpolarization.
At VV- polarization, the values of %Bias, root mean
squared error (RMSE) and Nash-Sutcliffe Efficiency (NSE) were
found 3.6186, 0.9373 and 0.9428 respectively.
Abstract: Main objective of this paper is to establish a link
between inertial forces of the bearings used in construction of wind
power plant and its behavior. Using bearings with lower inertial
forces has the immediate effect of decreasing inertia rotor system,
with significant results in increased energy efficiency, due to
decreased friction forces between rollers and raceways. The F.E.M.
analysis shows the appearance of uniform contact stress at the ends of
the rollers, demonstrated the necessity of production of low mass
bearings. Favorable results are expected in the economic field, by
reducing material consumption and by increasing the durability of
bearings. Using low mass bearings with hollow rollers instead of
solid rollers has an impact on working temperature, on vibrations and
noise which decrease. Implementation of types of hollow rollers of
cylindrical tubular type, instead of expensive rollers with logarithmic
profile, will bring significant inertial forces decrease with large
benefits in behavior of wind power plant.
Abstract: Wireless Sensor Networks (WSNs) enable new
applications and need non-conventional paradigms for the protocol
because of energy and bandwidth constraints, In WSN, sensor node’s
life is a critical parameter. Research on life extension is based on
Low-Energy Adaptive Clustering Hierarchy (LEACH) scheme,
which rotates Cluster Head (CH) among sensor nodes to distribute
energy consumption over all network nodes. CH selection in WSN
affects network energy efficiency greatly. This study proposes an
improved CH selection for efficient data aggregation in sensor
networks. This new algorithm is based on Bacterial Foraging
Optimization (BFO) incorporated in LEACH.
Abstract: A solution methodology without using integral
transformation is proposed to develop analytical solutions for
transient heat conduction in nonuniform hollow cylinders with
time-dependent boundary condition at the outer surface. It is shown
that if the thermal conductivity and the specific heat of the medium
are in arbitrary polynomial function forms, the closed solutions of the
system can be developed. The influence of physical properties on the
temperature distribution of the system is studied. A numerical
example is given to illustrate the efficiency and the accuracy of the
solution methodology.
Abstract: A lower consumption of thermal energy will
contribute not only to a reduction in the running costs, but also in the
reduction of pollutant emissions that contribute to the greenhouse
effect. Cogeneration or CHP (Combined Heat and Power) is the
system that produces power and usable heat simultaneously by
decreasing the pollutant emissions and increasing the efficiency.
Combined production of mechanical or electrical and thermal energy
using a simple energy source, such as oil, coal, natural or liquefied
gas, biomass or the sun; affords remarkable energy savings and
frequently makes it possible to operate with greater efficiency when
compared to a system producing heat and power separately. This
study aims to bring out the contributions of cogeneration systems to
the environment and sustainability by saving the energy and reducing
the emissions. In this way we made a comprehensive investigation in
the literature by focusing on the environmental aspects of the
cogeneration systems. In the light of these studies we reached that,
cogeneration systems must be consider in sustainability and their
benefits on protecting the ecology must be investigated.