Abstract: This paper presents the results of a study on the
influence of varying percentages of rock bridges along a basal surface
defining a biplanar failure mode. A pseudo-coupled-hydromechanical
brittle fracture analysis is adopted using the state-of-the-art code
Slope Model. Model results show that rock bridge failure is strongly
influenced by the incorporation of groundwater pressures. The
models show that groundwater pressure can promote total failure of a
5% rock bridge along the basal surface. Once the percentage of the
rock bridges increases to 10 and 15%, although, the rock bridges are
broken, full interconnection of the surface defining the basal surface
of the biplanar mode does not occur. Increased damage is caused
when the rock bridge is located at the daylighting end of the basal
surface in proximity to the blast damage zone. As expected, some
cracking damage is experienced in the blast damage zone, where
properties representing a good quality controlled damage blast
technique were assumed. Model results indicate the potential increase
of permeability towards the blast damage zone.
Abstract: Laura Island, which is located about 50 km away from
downtown, is a source of water supply in Majuro atoll, which is the
capital of the Republic of the Marshall Islands. Low and flat Majuro
atoll has neither river nor lake. It is very important for Majuro atoll to
ensure the conservation of its water resources. However, upconing,
which is the process of partial rising of the freshwater-saltwater
boundary near the water-supply well, was caused by the excess
pumping from it during the severe drought in 1998. Upconing will
make the water usage of the freshwater lens difficult. Thus,
appropriate water usage is required to prevent up coning in the
freshwater lens because there is no other water source during drought. Numerical simulation of water usage applying SEAWAT model
was conducted at the central part of Laura Island, including the water
supply well, which was affected by upconing. The freshwater lens was
created as a result of infiltration of consistent average rainfall. The lens
shape was almost the same as the one in 1985. 0 of monthly rainfall
and variable daily pump discharge were used to calculate the
sustainable pump discharge from the water supply well. Consequently,
the total amount of pump discharge was increased as the daily pump
discharge was increased, indicating that it needs more time to recover
from upconing. Thus, a pump standard to reduce the pump intensity is
being proposed, which is based on numerical simulation concerning
the occurrence of the up-coning phenomenon in Laura Island during
the drought.
Abstract: This study investigates how the site specific traffic
data differs from the Mechanistic Empirical Pavement Design
Software default values. Two Weigh-in-Motion (WIM) stations were
installed in Interstate-40 (I-40) and Interstate-25 (I-25) to developed
site specific data. A computer program named WIM Data Analysis
Software (WIMDAS) was developed using Microsoft C-Sharp (.Net)
for quality checking and processing of raw WIM data. A complete
year data from November 2013 to October 2014 was analyzed using
the developed WIM Data Analysis Program. After that, the vehicle
class distribution, directional distribution, lane distribution, monthly
adjustment factor, hourly distribution, axle load spectra, average
number of axle per vehicle, axle spacing, lateral wander distribution,
and wheelbase distribution were calculated. Then a comparative
study was done between measured data and AASHTOWare default
values. It was found that the measured general traffic inputs for I-40
and I-25 significantly differ from the default values.
Abstract: The end panels of a large rectangular industrial duct,
which experience significant internal pressures, also experience
considerable transverse shear due to transfer of gravity loads to the
supports. The current design practice of such thin plate panels for
shear load is based on methods used for the design of plate girder
webs. The structural arrangements, the loadings and the resulting
behavior associated with the industrial duct end panels are, however,
significantly different from those of the web of a plate girder. The
large aspect ratio of the end panels gives rise to multiple bands of
tension fields, whereas the plate girder web design is based on one
tension field. In addition to shear, the industrial end panels are
subjected to internal pressure which in turn produces significant
membrane action. This paper reports a study which was undertaken
to review the current industrial analysis and design methods and to
propose a comprehensive method of designing industrial duct end
panels for shear resistance. In this investigation, a nonlinear finite element model was
developed to simulate the behavior of industrial duct end panel, along
with the associated edge stiffeners, subjected to transverse shear and
internal pressures. The model considered the geometric imperfections
and constitutive relations for steels. Six scale independent
dimensionless parameters that govern the behavior of such end panel
were identified and were then used in a parametric study. It was
concluded that the plate slenderness dominates the shear strength of
stockier end panels, and whereas, both the plate slenderness and the
aspect ratio influence the shear strength of slender end panels. Based
on these studies, this paper proposes design aids for estimating the
shear strength of rectangular duct end panels.
Abstract: The Haussmannization plan of Cairo in 1867 formed a
regular network of roundabout spaces, though deteriorated at present.
The method of identifying the spatial structure of roundabout Cairo
for conservation matches the voronoi diagram with the space syntax
through their geometrical property of spatial convexity. In this
initiative, the primary convex hull of first-order voronoi adopts the
integral and control measurements of space syntax on Cairo’s
roundabout generators. The functional essence of royal palaces
optimizes the roundabout structure in terms of spatial measurements
and the symbolic voronoi projection of 'Tahrir Roundabout' over the
Giza Nile and Pyramids. Some roundabouts of major public and
commercial landmarks surround the pole of 'Ezbekia Garden' with a
higher control than integral measurements, which filter the new
spatial structure from the adjacent traditional town. Nevertheless, the
least integral and control measures correspond to the voronoi
contents of pollutant workshops and the plateau of old Cairo Citadel
with the visual compensation of new royal landmarks on top.
Meanwhile, the extended suburbs of infinite voronoi polygons
arrange high control generators of chateaux housing in 'garden city'
environs. The point pattern of roundabouts determines the
geometrical characteristics of voronoi polygons. The measured
lengths of voronoi edges alternate between the zoned short range at
the new poles of Cairo and the distributed structure of longer range.
Nevertheless, the shortest range of generator-vertex geometry
concentrates at 'Ezbekia Garden' where the crossways of vast Cairo
intersect, which maximizes the variety of choice at different spatial
resolutions. However, the symbolic 'Hippodrome' which is the largest
public landmark forms exclusive geometrical measurements, while
structuring a most integrative roundabout to parallel the royal syntax.
Overview of the symbolic convex hull of voronoi with space syntax
interconnects Parisian Cairo with the spatial chronology of scattered
monuments to conceive one universal Cairo structure. Accordingly,
the approached methodology of 'voronoi-syntax' prospects the future
conservation of roundabout Cairo at the inferred city-level concept.
Abstract: Coal fly ash, an industrial by product of coal
combustion thermal power plants is considered as a hazardous
material and its improper disposal has become an environmental
issue. On the other hand, manufacturing conventional clay bricks
involves on consumption of large amount of clay and leads
substantial depletion of topsoil. This paper unveils the possibility of
using fly ash as a partial replacement of clay for brick manufacturing
considering the local technology practiced in Bangladesh. The effect
of fly ash with different replacing ratio (0%, 20%, 30%, 40%, and
50% by volume) of clay on properties of bricks was studied. Bricks
were made in the field parallel to ordinary bricks marked with
specific number for different percentage to identify them at time of
testing. No physical distortion is observed in fly ash brick after
burning in the kiln. Results from laboratory test show that
compressive strength of brick is decreased with the increase of fly
ash and maximum compressive strength is found to be 19.6 MPa at
20% of fly ash. In addition, water absorption of fly ash brick is
increased with the increase of fly ash. The abrasion value and
Specific gravity of coarse aggregate prepared from brick with fly ash
also studied and the results of this study suggests that 20% fly ash
can be considered as the optimum fly ash content for producing good
quality bricks utilizing present practiced technology.
Abstract: The article deals with the personality of military
professionals (commanders) and their way of leading and
commanding today and in historical context. The first part focuses on
the leadership skills of Alexander the Great, who introduced strategic
innovations and even from today's perspective; he excelled in
efficient work with people. This paper focuses on the way which he
achieved his goals. Further attention is paid to approaches to
commander´s personality by other great generals. The paper is also
focused on personality traits of military professionals necessary for
successful management and leadership in today's variable and
challenging environment. Finally, attention is paid to the effective
and ineffective ways of behavior of commanders and determining
what styles of leadership is appropriate for a given situation, whether
in peacetime or on deployment.
Abstract: In this work, our goal is to optimize the nitriding treatment at a low-temperature of the steel 32CrMoV13 using gas mixtures of ammonia, nitrogen and hydrogen to improve the mechanical properties of the surface (good wear resistance, friction and corrosion), and of the diffusion layer of the nitrogen (good resistance to fatigue and good tenacity with heart). By limiting our work to the pure iron and to the alloys iron-chromium and iron-chromium-carbon, we have studied the various parameters which manage the nitriding: flow rate and composition of the gaseous phase, the interaction chromium-nitrogen and chromium-carbon by the help of experiments of nitriding realized in the laboratory by thermogravimetry. The acquired knowledge has been applied by the mastery of the growth of the γ' combination layer on the α diffusion layer in the case of the industrial steel 32CrMoV13.
Abstract: Biochar can be produced from the waste matter and its
application has been associated with returning of carbon in large
amounts into the soil. The impacts of this material on physical and
chemical properties of soil have been described. The biggest part of
the research work is dedicated to the hypothesis of this material’s
toxic effects on the soil life regarding its effect on the soil biological
component. At present, it has been worked on methods which could
eliminate these undesirable properties of biochar. One of the
possibilities is to mix biochar with organic material, such as compost,
or focusing on the natural processes acceleration in the soil. In the
experiment has been used as the addition of compost as well as the
elimination of toxic substances by promoting microbial activity in
aerated water environment. Biochar was aerated for 7 days in a
container with a volume of 20 l. This way modified biochar had six
times higher biomass production and reduce mineral nitrogen
leaching. Better results have been achieved by mixing biochar with
compost.
Abstract: Ensuring of continuity of business is basic strategy of
every company. Continuity of organization activities includes
comprehensive procedures that help in solving unexpected situations
of natural and anthropogenic character (for example flood, blaze,
economic situations). Planning of continuity operations is a process
that helps identify critical processes and implement plans for the
security and recovery of key processes. The aim of this article is to
demonstrate application of system approach to managing business
continuity called business continuity management systems in military
issues. This article describes the life cycle of business continuity
management which is based on the established cycle PDCA (Plan-
Do-Check-Act). After this is carried out by activities which are
making by University of Defence during activation of forces and
means of the integrated rescue system in case of emergencies -
accidents at a nuclear power plant in Czech Republic. Activities of
various stages of deployment earmarked forces and resources are
managed and evaluated by using MCMS application (Military
Continuity Management System).
Abstract: Now, the use of renewable energy power generation
has been advanced. In this paper, we compared the usable amount of
resource for photovoltaic power generation which was estimated using
the NEDO formula and the expansion support policy of photovoltaic
power generation which was researched using Internet in the
municipality level in Hokkaido and Aichi Prefecture, Japan. This
paper will contribute to grasp the current situation especially about the
policy. As a result, there were municipalities which seemed to be no
consideration of fitting the amount of resources. We think it would
need to consider the suitability between the resources and policies.
Abstract: Job satisfaction and motivation have been given an
important attention in psychology because they are seen as main
instruments in maintaining organizational growth and development;
they are also used to accomplish organizational aims and objectives.
However, it has been observed that some institutions failed in
motivating and stimulating their workers; in contrast, workers may be
motivated but not satisfied with the job and failed to perform
efficiently and effectively. It is hoped that the study of this nature
would be of significance value to all stakeholders in education
specifically, lecturers in higher institutions in Nigeria. Also, it is
hoped that the findings of this study will enhance lecturers’
effectiveness and performance in discharging their duties. In the light
of the above statements, this study investigated whether job
satisfaction and motivation predict lecturers’ effectiveness in Nigeria
Police Academy, Wudil, Kano State. Correlational research method
was adopted for the study, while purposive sampling technique was
used to choose the institution and the sampled lectures (70). Simple
random sampling technique was used to select one hundred cadets
across the academy. Two instruments were used to elicit information
from both lecturers and cadets. These were job satisfaction and
motivation; and lecturers’ effectiveness Questionnaires. The
instruments were subjected to pilot testing and found to have
reliability coefficient of 0.69 and 0.71 respectively. The results of the
study revealed that there was a significance relationship among job
satisfaction, motivation and lecturers effectiveness in Nigeria Police
Academy. There was a significance relationship between job
satisfaction and lecturers’ effectiveness in Nigeria Police Academy
the cal r is 0.21 while the crt r is 0.19. at p
Abstract: Over the past few decades, manufacturing has evolved
from a more labor-intensive set of mechanical processes to a
sophisticated set of information based technology processes. With the
existence of various advanced manufacturing technologies (AMTs),
more and more functions or jobs are performed by these machines
instead of human labour. This study was undertaken in order to
research the extent of AMTs adoption in manufacturing companies in
Kenya. In order to investigate a survey was conducted via
questionnaires that were sent to 183 selected AMT manufacturing
companies in Kenya. 92 companies responded positively. All the
surveyed companies were found to have a measure of investment in
at least two of the 14 types of AMTs investigated. In general the
company surveyed showed that the level of AMT adoption in Kenya
is very low with investments levels at a mean of 2.057 and
integration levels at a mean of 1.639 in a scale of 1-5.
Abstract: Present empirical paper investigates the relationship
between FDI and economic growth by 10 selected industries in 10
Central and Eastern European countries from the period 1995 to
2012. Different estimation approaches were used to explore the
connection between FDI and economic growth, for example OLS,
RE, FE with and without time dummies. Obtained empirical results
leads to some main consequences: First, the Central and East
European countries (CEEC) attracted foreign direct investment,
which raised the productivity of industries they entered in. It should
be concluded that the linkage between FDI and output growth by
industries is positive and significant enough to suggest that foreign
firm’s participation enhanced the productivity of the industries they
occupied. There had been an endogeneity problem in the regression
and fixed effects estimation approach was used which partially
corrected the regression analysis in order to make the results less
biased. Second, it should be stressed that the results show that time
has an important role in making FDI operational for enhancing output
growth by industries via total factor productivity. Third, R&D
positively affected economic growth and at the same time, it should
take some time for research and development to influence economic
growth. Fourth, the general trends masked crucial differences at the
country level: over the last 20 years, the analysis of the tables and
figures at the country level show that the main recipients of FDI of
the 11 Central and Eastern European countries were Hungary, Poland
and the Czech Republic. The main reason was that these countries
had more open door policies for attracting the FDI. Fifth, according
to the graphical analysis, while Hungary had the highest FDI inflow
in this region, it was not reflected in the GDP growth as much as in
other Central and Eastern European countries.
Abstract: A three-dimensional numerical simulation of flow
through mini and microchannels with designed roughness is
conducted here. The effect of the roughness height (surface
roughness), geometry, Reynolds number on the friction factor, and
Nusselt number is investigated. The study is carried out by
employing CFD software, CFX. Our work focuses on a water flow
inside a circular mini-channel of 1 mm and microchannels of 500 and
100 m in diameter. The speed entry varies from 0.1 m/s to 20 m/s.
The general trend can be observed that bigger sizes of roughness
element lead to higher flow resistance. It is found that the friction
factor increases in a nonlinear fashion with the increase in obstruction
height. Particularly, the effect of roughness can no longer be ignored
at relative roughness height higher than 3%. A significant increase in
Poiseuille number is detected for all configurations considered. The
same observation can be done for Nusselt number. The transition
zone between laminar and turbulent flow depends on the channel
diameter.
Abstract: The goal of this paper is to specify factors influencing
the profitability of selected banks. Next, a model will be created to
help establish variables that have a demonstrable influence on the
development of the selected banks' profitability ratios. Czech banks
and their international parent companies were selected for analyzing
profitability. Banks categorized as large banks (according to the
Czech National Bank's system, which ranks banks according to
balance sheet total) were selected to represent the Czech banks. Two
ratios, the return on assets ratio (ROA) and the return on equity ratio
(ROE) are used to assess bank profitability. Six endogenous and four
external indicators were selected from among other factors that
influence bank profitability. The data analyzed were for 2001–2013.
First, correlation analysis, which was supposed to eliminate
correlated values, was conducted. A large number of correlated
values were established on the basis of this analysis. The strongly
correlated values were omitted. Despite this, the subsequent
regression analysis of profitability for the individual banks that were
selected did not confirm that the selected variables influenced their
profitability. The studied factors' influence on bank profitability was
demonstrated only for Ceskoslovenska Obchodni Banka and Société
Générale using regression analysis. For Československa Obchodni
Banka, it was demonstrated that inflation level and the amount of the
central bank's interest rate influenced the return on assets ratio and
that capital adequacy and market concentration influenced the return
on equity ratio for Société Générale.
Abstract: We regard forecasting of energy consumption by
private production areas of a large industrial facility as well as by the
facility itself. As for production areas, the forecast is made based on
empirical dependencies of the specific energy consumption and the
production output. As for the facility itself, implementation of the
task to minimize the energy consumption forecasting error is based
on adjustment of the facility’s actual energy consumption values
evaluated with the metering device and the total design energy
consumption of separate production areas of the facility. The
suggested procedure of optimal energy consumption was tested based
on the actual data of core product output and energy consumption by
a group of workshops and power plants of the large iron and steel
facility. Test results show that implementation of this procedure gives
the mean accuracy of energy consumption forecasting for winter
2014 of 0.11% for the group of workshops and 0.137% for the power
plants.
Abstract: Sentiment analysis means to classify a given review
document into positive or negative polar document. Sentiment
analysis research has been increased tremendously in recent times
due to its large number of applications in the industry and academia.
Sentiment analysis models can be used to determine the opinion of
the user towards any entity or product. E-commerce companies can
use sentiment analysis model to improve their products on the basis
of users’ opinion. In this paper, we propose a new One-class Support
Vector Machine (One-class SVM) based sentiment analysis model
for movie review documents. In the proposed approach, we initially
extract features from one class of documents, and further test the
given documents with the one-class SVM model if a given new test
document lies in the model or it is an outlier. Experimental results
show the effectiveness of the proposed sentiment analysis model.
Abstract: In this paper, approach to incoherent signal detection
in multi-element antenna array are researched and modeled. Two
types of useful signals with unknown wavefront were considered:
first one, deterministic (Barker code), and second one, random
(Gaussian distribution). The derivation of the sufficient statistics took
into account the linearity of the antenna array. The performance
characteristics and detecting curves are modeled and compared for
different useful signals parameters and for different number of
elements of the antenna array. Results of researches in case of some
additional conditions can be applied to a digital communications
systems.
Abstract: We present probabilistic multinomial Dirichlet
classification model for multidimensional data and Gaussian process
priors. Here, we have considered efficient computational method that
can be used to obtain the approximate posteriors for latent variables
and parameters needed to define the multiclass Gaussian process
classification model. We first investigated the process of inducing a
posterior distribution for various parameters and latent function by
using the variational Bayesian approximations and important sampling
method, and next we derived a predictive distribution of latent
function needed to classify new samples. The proposed model is
applied to classify the synthetic multivariate dataset in order to verify
the performance of our model. Experiment result shows that our model
is more accurate than the other approximation methods.