Abstract: The aim of this paper is to present a comparative
study on two different methods for the evaluation of the equilibrium
point of a ship, core issue for designing an On Board Stability System
(OBSS) module that, starting from geometry information of a ship
hull, described by a discrete model in a standard format, and the
distribution of all weights onboard calculates the ship floating
conditions (in draught, heel and trim).
Abstract: Nowadays use of a new structural bracing system
called 'Knee Bracing System' have taken the specialists attention too
much. On the other hand nonlinear static analysis procedures in
estimate structures performance in earthquake time have taken
attention too much. One of these procedure is modal pushover
analysis (MPA) procedure. The accuracy of MPA procedure for
simple steel moment resisting frame has been verified and considered
in Chintanapakdee and Chopra-s article in 2003. Since the accuracy
of MPA procedure has not verified for semi-rigid steel frames with
knee bracing, we are going to get through with this matter in this
study. For this purpose, the selected structures are four frames with
different heights, 5 to 20 stories, will be designed according to AISC
criteria. Then MPA procedure is used for the same frames with
different rigidity percentiles of connections. The results of seismic
responses are compared with dynamic nonlinear response history
analysis as exact procedure and accuracy of MPA procedure is
evaluated. It seems that MPA procedure accuracy will come down by
reduction of the rigidity percentiles of semi-rigid connections.
Abstract: Some physical properties of musk lime (Citrus
microcarpa) were determined in this study. The average moisture
content (wet basis) of the fruit was found to be 85.10 (±0.72) %. The
mean of length, width and thickness of the fruit was 26.36 (±0.97),
26.40 (±1.04) and 25.26 (±0.94) mm respectively. The average value
for geometric mean diameter, sphericity, aspect ratio, mass, surface
area, volume, true density, bulk density and porosity was 26.00
(±0.82) mm, 98.67 (±2.04) %, 100.23 (±3.28) %, 10.007 (±0.878) g,
2125.07 (±133.93) mm2, 8800.00 (±731.82) mm3, 1002.87 (±39.16)
kgm-3, 501.70 (±22.58) kgm-3 and 49.89 (±3.15) % respectively.
The coefficient of static friction on four types of structural surface
was found to be varying from 0.238 (±0.025) for glass to 0.247
(±0.024) for steel surface.
Abstract: In this research work, investigations are carried out on
Continuous Wave (CW) Nd:YAG laser welding system after
preliminary experimentation to understand the influencing parameters
associated with laser welding of AISI 304. The experimental
procedure involves a series of laser welding trials on AISI 304
stainless steel sheets with various combinations of process parameters
like beam power, beam incident angle and beam incident angle. An
industrial 2 kW CW Nd:YAG laser system, available at Welding
Research Institute (WRI), BHEL Tiruchirappalli, is used for
conducting the welding trials for this research. After proper tuning of
laser beam, laser welding experiments are conducted on AISI 304
grade sheets to evaluate the influence of various input parameters on
weld bead geometry i.e. bead width (BW) and depth of penetration
(DOP). From the laser welding results, it is noticed that the beam
power and welding speed are the two influencing parameters on
depth and width of the bead. Three dimensional finite element
simulation of high density heat source have been performed for laser
welding technique using finite element code ANSYS for predicting
the temperature profile of laser beam heat source on AISI 304
stainless steel sheets. The temperature dependent material properties
for AISI 304 stainless steel are taken into account in the simulation,
which has a great influence in computing the temperature profiles.
The latent heat of fusion is considered by the thermal enthalpy of
material for calculation of phase transition problem. A Gaussian
distribution of heat flux using a moving heat source with a conical
shape is used for analyzing the temperature profiles. Experimental
and simulated values for weld bead profiles are analyzed for stainless
steel material for different beam power, welding speed and beam
incident angle. The results obtained from the simulation are
compared with those from the experimental data and it is observed
that the results of numerical analysis (FEM) are in good agreement
with experimental results, with an overall percentage of error
estimated to be within ±6%.
Abstract: Data mining (DM) is the process of finding and extracting frequent patterns that can describe the data, or predict unknown or future values. These goals are achieved by using various learning algorithms. Each algorithm may produce a mining result completely different from the others. Some algorithms may find millions of patterns. It is thus the difficult job for data analysts to select appropriate models and interpret the discovered knowledge. In this paper, we describe a framework of an intelligent and complete data mining system called SUT-Miner. Our system is comprised of a full complement of major DM algorithms, pre-DM and post-DM functionalities. It is the post-DM packages that ease the DM deployment for business intelligence applications.
Abstract: In this work, thermoelastic damping effect on the hemi- spherical shells is investigated. The material is selected silicon, and heat conduction equation for thermal flow is solved to obtain the temperature profile in which bending approximation with inextensional assumption of the model. Using the temperature profile, eigen-value analysis is performed to get the natural frequencies of hemispherical shells. Effects of mode numbers, radii and radial thicknesses of the model on the natural frequencies are analyzed in detail. Furthermore, the quality factor (Q-factor) is defined, and discussed for the ring and hemispherical shell.
Abstract: Bidding is a very important business function to find
latent contractors of construction projects. Moreover, bid markup is
one of the most important decisions for a bidder to gain a reasonable
profit. Since the bidding system is a complex adaptive system, bidding
agent need a learning process to get more valuable knowledge for a bid,
especially from past public bidding information. In this paper, we
proposed an iterative agent leaning model for bidders to make markup
decisions. A classifier for public bidding information named PIBS is
developed to make full use of history data for classifying new bidding
information. The simulation and experimental study is performed to
show the validity of the proposed classifier. Some factors that affect
the validity of PIBS are also analyzed at the end of this work.
Abstract: Using a texture database, a statistical estimation of
spring-back was conducted in this study on the basis of statistical
analysis. Both spring-back in bending deformation and experimental
data related to the crystal orientation show significant dispersion.
Therefore, a probabilistic statistical approach was established for the
proper quantification of these values. Correlation was examined
among the parameters F(x) of spring-back, F(x) of the buildup fraction
to three orientations after 92° bending, and F(x) at an as-received part
on the basis of the three-parameter Weibull distribution. Consequent
spring-back estimation using a texture database yielded excellent
estimates compared with experimental values.
Abstract: The European countries that during the past two
decades based their exchange rate regimes on currency board
arrangement (CBA) are usually analysed from the perspective of
corner solution choice’s stabilisation effects. There is an open
discussion on the positive and negative background of a strict
exchange rate regime choice, although it should be seen as part of the
transition process towards the monetary union membership. The
focus of the paper is on the Baltic countries that after two decades of
a rigid exchange rate arrangement and strongly influenced by global
crisis are finishing their path towards the euro zone. Besides the
stabilising capacity, the CBA is highly vulnerable regime, with
limited developing potential. The rigidity of the exchange rate (and
monetary) system, despite the ensured credibility, do not leave
enough (or any) space for the adjustment and/or active crisis
management. Still, the Baltics are in a process of recovery, with fiscal
consolidation measures combined with (painful and politically
unpopular) measures of internal devaluation. Today, two of them
(Estonia and Latvia) are members of euro zone, fulfilling their
ultimate transition targets, but de facto exchanging one fixed regime
with another.
The paper analyses the challenges for the CBA in unstable
environment since the fixed regimes rely on imported stability and
are sensitive to external shocks. With limited monetary instruments,
these countries were oriented to the fiscal policies and used a
combination of internal devaluation and tax policy measures. Despite
their rather quick recovery, our second goal is to analyse the long
term influence that the measures had on the national economy.
Abstract: The modern Kazakh society is characterized by strengthen cross-cultural communication, the emergence of new powerful subcultures, accelerated change in social systems and values. The socio-political reforms in all fields have changed the quality of social relationships and spiritual life.Cross-cultural approach involves the analysis of different types of behavior and communication, including the manifestation of the conflict, and the formation of marginal destructive stereotypes.
Abstract: This paper describes studies carried out to investigate
the viability of using wireless cameras as a tool in monitoring
changes in air quality. A camera is used to monitor the change in
colour of a chemically responsive polymer within view of the camera
as it is exposed to varying chemical species concentration levels. The
camera captures this image and the colour change is analyzed by
averaging the RGB values present. This novel chemical sensing
approach is compared with an established chemical sensing method
using the same chemically responsive polymer coated onto LEDs. In
this way, the concentration levels of acetic acid in the air can be
tracked using both approaches. These approaches to chemical plume
tracking have many applications for air quality monitoring.
Abstract: Development of artificial neural network (ANN) for
prediction of aluminum workpieces' surface roughness in ultrasonicvibration
assisted turning (UAT) has been the subject of the present
study. Tool wear as the main cause of surface roughness was also
investigated. ANN was trained through experimental data obtained
on the basis of full factorial design of experiments. Various
influential machining parameters were taken into consideration. It
was illustrated that a multilayer perceptron neural network could
efficiently model the surface roughness as the response of the
network, with an error less than ten percent. The performance of the
trained network was verified by further experiments. The results of
UAT were compared with the results of conventional turning
experiments carried out with similar machining parameters except for
the vibration amplitude whence considerable reduction was observed
in the built-up edge and the surface roughness.
Abstract: The changes in quality properties and nutritional
components in two fermented mugworts (Artemisia capillaries
Thumberg, Artemisiaeasiaticae Nakai) were characterized followed
by the rapid pattern analysis of volatile flavor compounds by Electric
Nose based on SAW(Surface Acoustic Wave) sensor in GC system.
There were remarkable decreases in the pH and small changes in the
total soluble solids after fermentation. The L (lightness) and b
(yellowness) values in Hunter's color system were shown to be
decreased, whilst the a (redness) value was increased by fermentation.
The HPLC analysis demonstrated that total amino acids were
increased in quantity and the essential amino acids were contained
higher in A. asiaticaeNakai than in A. capillaries Thumberg. While
the total polyphenol contents were not affected by fermentation, the
total sugar contents were dramatically decreased. Scopoletinwere
highly abundant in A. capillarisThumberg, however, it was not
detected in A. asiaticaeNakai. Volatile flavor compounds by Electric
Nose showed that the intensity of several peaks were increased much
and seven additional flavor peaks were newly produced after
fermentation. The flavor differences of two mugworts were clearly
distinguished from the image patterns of VaporPrintTM which indicate
that the fermentation enables the two mugworts to have subtle flavor
differences.
Abstract: There is increasing pressure on, and decline of
mopane woodlands due to increasing use and competition for
mopane resources in Zimbabwe in Namibia. Community management strategies, based largely on local knowledge are
evidently unable to cope. Research has generated potentially useful
information for mopane woodland management, but this information
has not been utilized. The work reported in this paper sought to add value to research work conducted on mopane woodlands by
developing effective community-based mopane woodland
management regimes that were based on both local and scientific
knowledge in Zimbabwe and Namibia. The conditions under which research findings were likely to be adopted for mopane woodland management by communities were investigated. The study was conducted at two sites each in Matobo and Omusati Districts in Zimbabwe and Namibia respectively. The mopane woodland
resources in the two study areas were assessed using scientific
ecological methods. A range of participatory methods was used to collect information on use of mopane woodland resources by communities, institutional arrangements governing access to and use
of these resources and to evaluate scientific knowledge for
applicability in local management regimes. Coppicing, thinning and
pollarding were the research generated management methods evaluated. Realities such as availability of woodland resources and
social roles and responsibilities influenced preferences for woodland
management interventions
Abstract: There are very complex communication systems, as
the multifunction radar, MFAR (Multi-Function Array Radar), where
functions are integrated all together, and simultaneously are
performed the classic functions of tracking and surveillance, as all
the functions related to the communication, countermeasures, and
calibration. All these functions are divided into the tasks to execute.
The task scheduler is a key element of the radar, since it does the
planning and distribution of energy and time resources to be shared
and used by all tasks. This paper presents schedulers based on the use
of multiple queue. Several schedulers have been designed and
studied, and it has been made a comparative analysis of different
performed schedulers. The tests and experiments have been done by
means of system software simulation. Finally a suitable set of radar
characteristics has been selected to evaluate the behavior of the task
scheduler working.
Abstract: Since the actuator capacity is limited, in the real
application of active control systems under sever earthquakes it is
conceivable that the actuators saturate, hence the actuator saturation
should be considered as a constraint in design of optimal controllers.
In this paper optimal design of active controllers for nonlinear
structures by considering actuator saturation, has been studied. The
proposed method for designing optimal controllers is based on
defining an optimization problem which the objective has been to
minimize the maximum displacement of structure when a limited
capacity for actuator has been used. To this end a single degree of
freedom (SDF) structure with a bilinear hysteretic behavior has been
simulated under a white noise ground acceleration of different
amplitudes. Active tendon control mechanism, comprised of prestressed
tendons and an actuator, and extended nonlinear Newmark
method based instantaneous optimal control algorithm have been
used. To achieve the best results, the weights corresponding to
displacement, velocity, acceleration and control force in the
performance index have been optimized by the Distributed Genetic
Algorithm (DGA). Results show the effectiveness of the proposed
method in considering actuator saturation. Also based on the
numerical simulations it can be concluded that the actuator capacity
and the average value of required control force are two important
factors in designing nonlinear controllers which consider the actuator
saturation.
Abstract: This paper presents a comparative study on two most
popular control strategies for Permanent Magnet Synchronous Motor
(PMSM) drives: field-oriented control (FOC) and direct torque
control (DTC). The comparison is based on various criteria including
basic control characteristics, dynamic performance, and
implementation complexity. The study is done by simulation using
the Simulink Power System Blockset that allows a complete
representation of the power section (inverter and PMSM) and the
control system. The simulation and evaluation of both control
strategies are performed using actual parameters of Permanent
Magnet Synchronous Motor fed by an IGBT PWM inverter.
Abstract: The service sector continues to grow and the percentage
of GDP accounted for by service industries keeps increasing. The
growth and importance of service to an economy is not just a
phenomenon of advanced economies, service is now a majority of the
world gross domestic products. However, the performance evaluation
process of new service development problems generally involves
uncertain and imprecise data. This paper presents a 2-tuple fuzzy
linguistic computing approach to dealing with heterogeneous
information and information loss problems while the processes of
subjective evaluation integration. The proposed method based on group
decision-making scenario to assist business managers in measuring
performance of new service development manipulates the
heterogeneity integration processes and avoids the information loss
effectively.
Abstract: The present work is concerned with sulfidation of Cu,
Zn and Ni containing plating wastewater with CaS. The sulfidation
experiments were carried out at a room temperature by adding solid
CaS to simulated metal solution containing either single-metal of Ni,
Zn and Cu, or Ni-Zn-Cu mixture. At first, the experiments were
conducted without pH adjustment and it was found that the complete
sulfidation of Zn and Ni was achieved at an equimolar ratio of CaS to a
particular metal. However, in the case of Cu, a complete copper
sulfidation was achieved at CaS to Cu molar ratio of about 2. In the
case of the selective sulfidation, a simulated plating solution
containing Cu, Zn and Ni at the concentration of 100 mg/dm3 was
treated with CaS under various pH conditions. As a result, selective
precipitation of metal sulfides was achieved by a sulfidation treatment
at different pH values. Further, the precipitation agents of NaOH,
Na2S and CaS were compared in terms of the average specific
filtration resistance and compressibility coefficients of metal sulfide
slurry. Consequently, based on the lowest filtration parameters of the
produced metal sulfides, it was concluded that CaS was the most
effective precipitation agent for separation and recovery of Cu, Zn and
Ni.
Abstract: Today, numerical simulation is a powerful tool to
solve various hydraulic engineering problems. The aim of this
research is numerical solutions of shallow water equations using
finite volume method for Simulations of dam break over wet and dry
bed. In order to solve Riemann problem, Roe-s approximate solver is
used. To evaluate numerical model, simulation was done in 1D and
2D states. In 1D state, two dam break test over dry bed (with and
without friction) were studied. The results showed that Structural
failure around the dam and damage to the downstream constructions
in bed without friction is more than friction bed. In 2D state, two
tests for wet and dry beds were done. Generally in wet bed case,
waves are propagated to canal sides but in dry bed it is not
significant. Therefore, damage to the storage facilities and
agricultural lands in wet bed case is more than in dry bed.