Abstract: In this paper, we will implement three-dimensional pursuit guidance law with feedback linearization control method and study the effects of parameters. First, we introduce guidance laws and equations of motion of a missile. Pursuit guidance law is our highlight. We apply feedback linearization control method to obtain the accelerations to implement pursuit guidance law. The solution makes warhead direction follow with line-of-sight. Final, the simulation results show that the exact solution derived in this paper is correct and some factors e.g. control gain, time delay, are important to implement pursuit guidance law.
Abstract: This paper analyses the unsteady, two-dimensional
stagnation point flow of an incompressible viscous fluid over a flat
sheet when the flow is started impulsively from rest and at the same
time, the sheet is suddenly stretched in its own plane with a velocity
proportional to the distance from the stagnation point. The partial
differential equations governing the laminar boundary layer forced
convection flow are non-dimensionalised using semi-similar
transformations and then solved numerically using an implicit finitedifference
scheme known as the Keller-box method. Results
pertaining to the flow and heat transfer characteristics are computed
for all dimensionless time, uniformly valid in the whole spatial region
without any numerical difficulties. Analytical solutions are also
obtained for both small and large times, respectively representing the
initial unsteady and final steady state flow and heat transfer.
Numerical results indicate that the velocity ratio parameter is found
to have a significant effect on skin friction and heat transfer rate at
the surface. Furthermore, it is exposed that there is a smooth
transition from the initial unsteady state flow (small time solution) to
the final steady state (large time solution).
Abstract: In this article, we present a web server based solution
for implementing a system for intelligent navigation. In this solution
we use real time collected data and traffic history to establish the best
route for navigation. This is a low cost solution that is easily to
implement and extend. There is no need any infrastructure at road
network level except only a device that collect data about traffic in
key road crossing. The presented solution creates a strong base for
traffic pursuit and offers an infrastructure for navigation applications.
Abstract: In this work, I present a review on Sparse Distributed
Memory for Small Cues (SDMSCue), a variant of Sparse Distributed
Memory (SDM) that is capable of handling small cues. I then conduct
and show some cognitive experiments on SDMSCue to test its
cognitive soundness compared to SDM. Small cues refer to input
cues that are presented to memory for reading associations; but have
many missing parts or fields from them. The original SDM failed to
handle such a problem. SDMSCue handles and overcomes this
pitfall. The main idea in SDMSCue; is the repeated projection of the
semantic space on smaller subspaces; that are selected based on the
input cue length and pattern. This process allows for Read/Write
operations using an input cue that is missing a large portion.
SDMSCue is augmented with the use of genetic algorithms for
memory allocation and initialization. I claim that SDM functionality
is a subset of SDMSCue functionality.
Abstract: Electronics Products that achieve high levels of integrated communications, computing and entertainment, multimedia features in small, stylish and robust new form factors are winning in the market place. Due to the high costs that an industry may undergo and how a high yield is directly proportional to high profits, IC (Integrated Circuit) manufacturers struggle to maximize yield, but today-s customers demand miniaturization, low costs, high performance and excellent reliability making the yield maximization a never ending research of an enhanced assembly process. With factors such as minimum tolerances, tighter parameter variations a systematic approach is needed in order to predict the assembly process. In order to evaluate the quality of upcoming circuits, yield models are used which not only predict manufacturing costs but also provide vital information in order to ease the process of correction when the yields fall below expectations. For an IC manufacturer to obtain higher assembly yields all factors such as boards, placement, components, the material from which the components are made of and processes must be taken into consideration. Effective placement yield depends heavily on machine accuracy and the vision of the system which needs the ability to recognize the features on the board and component to place the device accurately on the pads and bumps of the PCB. There are currently two methods for accurate positioning, using the edge of the package and using solder ball locations also called footprints. The only assumption that a yield model makes is that all boards and devices are completely functional. This paper will focus on the Monte Carlo method which consists in a class of computational algorithms (information processed algorithms) which depends on repeated random samplings in order to compute the results. This method utilized in order to recreate the simulation of placement and assembly processes within a production line.
Abstract: Colored Petri Nets (CPN) are very known kind of
high level Petri nets. With sound and complete semantics, rewriting
logic is one of very powerful logics in description and verification of
non-deterministic concurrent systems. Recently, CPN semantics are
defined in terms of rewriting logic, allowing us to built models by
formal reasoning. In this paper, we propose an automatic translation
of CPN to the rewriting logic language Maude. This tool allows
graphical editing and simulating CPN. The tool allows the user
drawing a CPN graphically and automatic translating the graphical
representation of the drawn CPN to Maude specification. Then,
Maude language is used to perform the simulation of the resulted
Maude specification. It is the first rewriting logic based environment
for this category of Petri Nets.
Abstract: High-frequency (HF) communications have been used by military organizations for more than 90 years. The opportunity of very long range communications without the need for advanced equipment makes HF a convenient and inexpensive alternative of satellite communications. Besides the advantages, voice and data transmission over HF is a challenging task, because the HF channel generally suffers from Doppler shift and spread, multi-path, cochannel interference, and many other sources of noise. In constructing an HF data modem, all these effects must be taken into account. STANAG 4539 is a NATO standard for high-speed data transmission over HF. It allows data rates up to 12800 bps over an HF channel of 3 kHz. In this work, an efficient implementation of STANAG 4539 on a single Texas Instruments- TMS320C6747 DSP chip is described. The state-of-the-art algorithms used in the receiver and the efficiency of the implementation enables real-time high-speed data / digitized voice transmission over poor HF channels.
Abstract: The mesoporous MoO3/γ-Al2O3 catalyst was prepared
by incipient wetness impregnation method aiming to investigate the
effect of drying method and molybdenum content on the catalyst
property and performance towards the oxidation of benzothiophene
(BT), dibenzothiophene (DBT) and 4,6-dimethyle dibenzothiophene
(4,6-DMDBT) with H2O2 for deep oxidative desulfurization of diesel
fuel. The catalyst was characterized by XRD, BET, BJH and SEM
method. The catalyst with 10wt.% and 15wt.% Mo content represent
same optimum performance for DBT and 4,6-DMDBT removal, but
a catalyst with 10wt.% Mo has higher efficiency than 15wt.% Mo for
BT conversion. The SEM images show that use of rotary evaporator
in drying step reaches a more homogenous impregnation. The
oxidation reactivity of different sulfur compounds was studied which
followed the order of DBT>4,6-DMDBT>>BT.
Abstract: Liposomal magnetofection is a simple, highly efficient
technology for cell transfection, demonstrating better outcome than a
number of other common gene delivery methods. However,
aggregate complexes distribution over the cell surface is non-uniform
due to the gradient of the permanent magnetic field. The aim of this
study was to estimate the efficiency of liposomal magnetofection for
prostate carcinoma PC3 cell line using newly designed device,
“DynaFECTOR", ensuring magnetofection in a dynamic gradient
magnetic field. Liposomal magnetofection in a dynamic gradient
magnetic field demonstrated the highest transfection efficiency for
PC3 cells – it increased for 21% in comparison with liposomal
magnetofection and for 42% in comparison with lipofection alone.
The optimal incubation time under dynamic magnetic field for PC3
cell line was 5 minutes and the optimal rotation frequency of
magnets – 5 rpm. The new approach also revealed lower cytotoxic
effect to cells than liposomal magnetofection.
Abstract: We present the results of a case study aiming to assess the reflection of the tourism community in the Web and its usability to propose new ways to communicate visually. The wealth of information contained in the Web and the clear facilities to communicate personals points of view makes of the social web a new space of exploration. In this way, social web allow the sharing of information between communities with similar interests. However, the tourism community remains unexplored as is the case of the information covered in travel stories. Along the Web, we find multiples sites allowing the users to communicate their experiences and personal points of view of a particular place of the world. This cultural heritage is found in multiple documents, usually very little supplemented with photos, so they are difficult to explore due to the lack of visual information. This paper explores the possibility of analyzing travel stories to display them visually on maps and generate new knowledge such as patterns of travel routes. This way, travel narratives published in electronic formats can be very important especially to the tourism community because of the great amount of knowledge that can be extracted. Our approach is based on the use of a Geoparsing Web Service to extract geographic coordinates from travel narratives in order to draw the geo-positions and link the documents into a map image.
Abstract: Gamboge disorder (GD) or fruit damage by the yellow sap is a major problem in mangosteen. Mangosteen plants varied in the level of GD, from very low or non GD to low, moderate and high GD. However it was difficult to differentiate between GD and non GD plants because evaluation of the disorder is strongly influenced by environment. In this study we investigated the usefulness of primer designed from bioinformatics related to cell wall strength, termed as MCWS, to predict GD. Plant materials used were 28 mangosteen plants selected based on percentage of GD categorized as high, moderate, low and very low or non GD. The result showed that the specific DNA fragments were absent in the high GD accessions. The MCWS marker suggests as a novel polymorphic marker for GD in mangosteen as well as a marker for detect variability in mangosteen as apomictic plant.
Abstract: In CMOS integrated circuit design there is a trade-off between static power consumption and technology scaling. Recently, the power density has increased due to combination of higher clock speeds, greater functional integration, and smaller process geometries. As a result static power consumption is becoming more dominant. This is a challenge for the circuit designers. However, the designers do have a few methods which they can use to reduce this static power consumption. But all of these methods have some drawbacks. In order to achieve lower static power consumption, one has to sacrifice design area and circuit performance. In this paper, we propose a new method to reduce static power in the CMOS VLSI circuit using Variable Body Biasing technique without being penalized in area requirement and circuit performance.
Abstract: The importance for manipulating an incorporated
scaffold and directing cell behaviors is well appreciated for tissue
engineering. Here, we developed newly nano-topographic oxidized
silicon nanosponges capable of being various chemical modifications
to provide much insight into the fundamental biology of how cells
interact with their surrounding environment in vitro. A wet etching
technique is exerted to allow us fabricated the silicon nanosponges in a
high-throughput manner. Furthermore, various organo-silane
chemicals enabled self-assembled on the surfaces by vapor deposition.
We have found that Chinese hamster ovary (CHO) cells displayed
certain distinguishable morphogenesis, adherent responses, and
biochemical properties while cultured on these chemical modified
nano-topographic structures in compared with the planar oxidized
silicon counterparts, indicating that cell behaviors can be influenced
by certain physical characteristic derived from nano-topography in
addition to the hydrophobicity of contact surfaces crucial for cell
adhesion and spreading. Of particular, there were predominant
nano-actin punches and slender protrusions formed while cells were
cultured on the nano-topographic structures. This study shed potential
applications of these nano-topographic biomaterials for controlling
cell development in tissue engineering or basic cell biology research.
Abstract: Determination of wellbore problems during a
production/injection process might be evaluated thorough
temperature log analysis. Other applications of this kind of log
analysis may also include evaluation of fluid distribution analysis
along the wellbore and identification of anomalies encountered
during production/injection process. While the accuracy of such
prediction is paramount, the common method of determination of a
wellbore temperature log includes use of steady-state energy balance
equations, which hardly describe the real conditions as observed in
typical oil and gas flowing wells during production operation; and
thus increase level of uncertainties. In this study, a practical method
has been proposed through development of a simplified semianalytical
model to apply for predicting temperature profile along the
wellbore. The developed model includes an overall heat transfer
coefficient accounting all modes of heat transferring mechanism,
which has been focused on the prediction of a temperature profile as
a function of depth for the injection/production wells. The model has
been validated with the results obtained from numerical simulation.
Abstract: The present paper concerns with the influence of fiber
packing on the transverse plastic properties of metal matrix
composites. A micromechanical modeling procedure is used to
predict the effective mechanical properties of composite materials at
large tensile and compressive deformations. Microstructure is
represented by a repeating unit cell (RUC). Two fiber arrays are
considered including ideal square fiber packing and random fiber
packing defined by random sequential algorithm. The
micromechanical modeling procedure is implemented for
graphite/aluminum metal matrix composite in which the
reinforcement behaves as elastic, isotropic solids and the matrix is
modeled as an isotropic elastic-plastic solid following the von Mises
criterion with isotropic hardening and the Ramberg-Osgood
relationship between equivalent true stress and logarithmic strain.
The deformation is increased to a considerable value to evaluate both
elastic and plastic behaviors of metal matrix composites. The yields
strength and true elastic-plastic stress are determined for
graphite/aluminum composites.
Abstract: In this study, synthesis of biomemitic patterned nano
hydroxyapatite-starch biocomposites using different concentration of
starch to evaluate effect of polymer alteration on biocomposites
structural properties has been reported. Formation of hydroxyapatite
nano particles was confirmed by X-ray diffraction (XRD) and Fourier
transform infrared spectroscopy (FT-IR). Size and morphology of the
samples were characterized using scanning and transmission electron
microscopy (SEM and TEM). It seems that by increasing starch
content, the more active site of polymer (oxygen atoms) can be
provided for interaction with Ca2+ followed by phosphate and
hydroxyl group.
Abstract: Post cracking behavior and load –bearing capacity of
the steel fiber reinforced high-strength concrete (SFRHSC) are
dependent on the number of fibers are crossing the weakest crack
(bridged the crack) and their orientation to the crack surface. Filling
the mould by SFRHSC, fibers are moving and rotating with the
concrete matrix flow till the motion stops in each internal point of the
concrete body. Filling the same mould from the different ends
SFRHSC samples with the different internal structures (and different
strength) can be obtained. Numerical flow simulations (using Newton
and Bingham flow models) were realized, as well as single fiber
planar motion and rotation numerical and experimental investigation
(in viscous flow) was performed. X-ray pictures for prismatic
samples were obtained and internal fiber positions and orientations
were analyzed. Similarly fiber positions and orientations in cracked
cross-section were recognized and were compared with numerically
simulated. Structural SFRHSC fracture model was created based on
single fiber pull-out laws, which were determined experimentally.
Model predictions were validated by 15x15x60cm prisms 4 point
bending tests.
Abstract: The effect of notch depth on the elastic new strainconcentration
factor (SNCF) of rectangular bars with single edge Unotch
under combined loading is studied here. The finite element
method (FEM) and super position technique are used in the current
study. This new SNCF under combined loading of static tension and
pure bending has been defined under triaxial stress state. The
employed specimens have constant gross thickness of 16.7 mm and
net section thickness varied to give net-to-gross thickness ratio ho/Ho
from 0.2 to 0.95. The results indicated that the elastic SNCF for
combined loading increases with increasing notch depth up to ho/Ho =
0.7 and sharply decreases with increasing notch depth. It is also
indicated that the elastic SNCF of combined loading is greater than
that of pure bending and less than that of the static tension for 0.2 ≤
ho/Ho ≤ 0.7. However, the elastic SNCF of combined loading is the
elastic SNCF for static tension and less than that of pure bending for
shallow notches (i.e. 0.8 ≤ ho/Ho ≤ 0.95).
Abstract: The main aim of this paper is to develop and calibrate
an econometric model for modeling prices of long term electricity
futures contracts. The calibration of our model is performed on data
from EEX AG allowing us to capture the specific features of German
electricity market. The data sample contains several structural breaks
which have to be taken into account for modeling. We model the data
with an ARIMAX model which reveals high correlation between the
price of electricity futures contracts and prices of LT futures
contracts of fuels (namely coal, natural gas and crude oil). Besides
this, also a share price index of representative electricity companies
traded on Xetra, spread between 10Y and 1Y German bonds and
exchange rate between EUR and USD appeared to have significant
explanatory power over these futures contracts on EEX.
Abstract: We numerically study the three-dimensional
magnetohydrodynamics (MHD) stability of oscillatory natural
convection flow in a rectangular cavity, with free top surface, filled
with a liquid metal, having an aspect ratio equal to A=L/H=5, and
subjected to a transversal temperature gradient and a uniform
magnetic field oriented in x and z directions. The finite volume
method was used in order to solve the equations of continuity,
momentum, energy, and potential. The stability diagram obtained in
this study highlights the dependence of the critical value of the
Grashof number Grcrit , with the increase of the Hartmann number
Ha for two orientations of the magnetic field. This study confirms
the possibility of stabilization of a liquid metal flow in natural
convection by application of a magnetic field and shows that the
flow stability is more important when the direction of magnetic field
is longitudinal than when the direction is transversal.