Abstract: The effect of carbon nanofibers (CNFs) on the
electrical properties of Poly(vinylidene fluoride-hexafluoropropylene)
(P(VdF-HFP)) based gel polymer electrolytes has been investigated
in the present work. The length and diameter ranges of CNFs used in
the present work are 5-50 μm and 200-600 nm respectively. The
nanocomposite gel polymer electrolytes have been synthesized by
solution casting technique with varying CNFs content in terms of
weight percentage. Electrochemical impedance analysis demonstrates
that the reinforcement of carbon nanofibers significantly enhances the
ionic conductivity of the polymer electrolyte. The decrease of
crystallinity of P(VdF-HFP) due the addition of CNFs has been
confirmed by X-ray diffraction (XRD). The interaction of CNFs with
various constituents of nanocomposite gel polymer electrolytes has
been assessed by Fourier Transform Infrared (FTIR) spectroscopy.
Moreover CNFs added gel polymer electrolytes offer superior
thermal stability as compared to that of CNFs free electrolytes as
confirmed by Thermogravimetric analysis (TGA).
Abstract: A new approach has been developed to estimate the
load share and distribution of worm gear drives, and to calculate the
instantaneous tooth meshing stiffness. In the approach, the worm gear
drive was modelled as a series of spur gear slices, and each slice was
analyzed separately using the well-established formulae of spur gear
loading and stresses. By combining the results obtained for all slices,
the entire envolute worm gear set loading and stressing was obtained. The geometric modelling method presented allows tooth elastic
deformation and tooth root stresses of worm gear drives under
different load conditions to be investigated. Based on the slicing
method introduced in this study, the instantaneous meshing stiffness
and load share are obtained. In comparison with existing methods,
this approach has both good analysis accuracy and less computing
time.
Abstract: Carefully scheduling the operations of pumps can be
resulted to significant energy savings. Schedules can be defined
either implicit, in terms of other elements of the network such as tank
levels, or explicit by specifying the time during which each pump is
on/off. In this study, two new explicit representations based on timecontrolled
triggers were analyzed, where the maximum number of
pump switches was established beforehand, and the schedule may
contain fewer switches than the maximum. The optimal operation of
pumping stations was determined using a Jumping Particle Swarm
Optimization (JPSO) algorithm to achieve the minimum energy cost.
The model integrates JPSO optimizer and EPANET hydraulic
network solver. The optimal pump operation schedule of VanZyl
water distribution system was determined using the proposed model
and compared with those from Genetic and Ant Colony algorithms.
The results indicate that the proposed model utilizing the JPSO
algorithm is a versatile management model for the operation of realworld
water distribution system.
Abstract: This paper deals with the problem of management of
information resources in libraries of the public institution Sultan
Moulay Slimane University (SMSU) in order to analyze the
satisfaction of the readers, and allow university leaders to make better
strategic and instant decisions. For this, the integration of an
integrated management decision library system is a priority program
of higher education, as part of the Digital Morocco, which has a
proactive policy to develop the use of new technologies information
and communication in higher institutions. This operational
information system can provide better services to the students and for
the leaders. Our approach is to integrate the tools of business
intelligence (BI) in the library management by using power BI.
Abstract: At the present time, awareness, education, computer
simulation and information systems protection are very serious and
relevant topics. The article deals with perspectives and possibilities of
implementation of emergence or natural hazard threats into the
system which is developed for communication among members of
crisis management staffs. The Czech Hydro-Meteorological Institute
with its System of Integrated Warning Service resents the largest
usable base of information. National information systems are connected to foreign systems,
especially to flooding emergency systems of neighboring countries,
systems of European Union and international organizations where the
Czech Republic is a member. Use of outputs of particular information
systems and computer simulations on a single communication
interface of information system for communication among members
of crisis management staff and setting the site interoperability in the
net will lead to time savings in decision-making processes in solving
extraordinary events and crisis situations. Faster managing of an
extraordinary event or a crisis situation will bring positive effects and
minimize the impact of negative effects on the environment.
Abstract: The system of ordinary nonlinear differential
equations describing sliding velocity during impact with friction for a
three-dimensional rigid-multibody system is developed. No analytical
solutions have been obtained before for this highly nonlinear system.
Hence, a power series solution is proposed. Since the validity of this
solution is limited to its convergence zone, a suitable time step is
chosen and at the end of it a new series solution is constructed. For a
case study, the trajectory of the sliding velocity using the proposed
method is built using 6 time steps, which coincides with a Runge-
Kutta solution using 38 time steps.
Abstract: The moisture content of densified biomass is a
limiting parameter influencing the quality of this solid biofuel. It
influences its calorific value, density, mechanical strength and
dimensional stability as well as affecting its production process. This
paper deals with experimental research into the effect of moisture
content of the densified material on the final quality of biofuel in the
form of logs (briquettes or pellets). Experiments based on the singleaxis
densification of the spruce sawdust were carried out with a
hydraulic piston press (piston and die), where the densified logs were
produced at room temperature. The effect of moisture content on the
qualitative properties of the logs, including density, change of
moisture, expansion and physical changes, and compressive and
impact resistance were studied. The results show the moisture ranges
required for producing good-quality logs. The experiments were
evaluated and the moisture content of the tested material was
optimized to achieve the optimum value for the best quality of the
solid biofuel. The dense logs also have high-energy content per unit
volume. The research results could be used to develop and optimize
industrial technologies and machinery for biomass densification to
achieve high quality solid biofuel.
Abstract: Healthcare safety has been perceived important. It is
essential to prevent troubles in healthcare processes for healthcare
safety. Trouble prevention is based on trouble prediction using
accumulated knowledge on processes, troubles, and countermeasures.
However, information on troubles has not been accumulated in
hospitals in the appropriate structure, and it has not been utilized
effectively to prevent troubles. In the previous study, however a
detailed knowledge acquisition process for trouble prediction was
proposed, the knowledgebase for countermeasures was not involved.
In this paper, we aim to propose the structure of the knowledgebase for
countermeasures, in the knowledge acquisition process for trouble
prediction in healthcare process. We first design the structure of
countermeasures and propose the knowledge representation form on
countermeasures. Then, we evaluate the validity of the proposal, by
applying it into an actual hospital.
Abstract: The current study aims to highlight the loading
characteristics impact on the time evolution (focusing particularly on
long term effects) of the deformation of realized reinforced concrete
beams. Namely the tension stiffening code provisions (i.e. within
Eurocode 2) are reviewed with a clear intention to reassess their
operational value and predicting capacity. In what follows the
experimental programme adopted along with some preliminary
findings and numerical modeling attempts are presented. For a range of long slender reinforced concrete simply supported
beams (4200 mm) constant static sustained and repeated cyclic
loadings were applied mapping the time evolution of deformation.
All experiments were carried out at the Heavy Structures Lab of the
University of Leeds. During tests the mid-span deflection, creep
coefficient and shrinkage strains were monitored for duration of 90
days. The obtained results are set against the values predicted by
Eurocode 2 and the tools within an FE commercial package (i.e.
Midas FEA) to yield that existing knowledge and practise is at times
over-conservative.
Abstract: For the shrimp companies to remain relevant to its local
and international consumers, they must offer new shrimp product and
services. It must work actively not just to create value for the consumer,
but to involve the consumer in co-creating value for shrimp product
innovation in the market. In this theoretical work, we conceptualize the
business concept of value co-creation in the context of shrimp products,
and propose a framework of value co-creation for shrimp product
innovation in shrimp industries. With guidance on value co-creation in
in shrimp industry, and shrimp value chain actors mapped to the
co-creation cycle, companies can use the framework to offer new
shrimp product to consumer communities. Although customer
co-creation is known approach in the world, it is not commonly used
by the companies in Bangladesh. This paper makes an original
contribution by conceptualizing co-creation and set the examples of
best co-creation practices in food sector. The results of the study
provide management with guidelines for successful co-creation
projects with an innovation- and market-oriented approach. The
framework also provides a basis for further research in this area.
Abstract: In VLSI, testing plays an important role. Major
problem in testing are test data volume and test power. The important
solution to reduce test data volume and test time is test data
compression. The Proposed technique combines the bit maskdictionary
and 2n pattern run length-coding method and provides a
substantial improvement in the compression efficiency without
introducing any additional decompression penalty. This method has
been implemented using Mat lab and HDL Language to reduce test
data volume and memory requirements. This method is applied on
various benchmark test sets and compared the results with other
existing methods. The proposed technique can achieve a compression
ratio up to 86%.
Abstract: Drought is one of the most serious problems posing a
grave threat to cereals production including maize. Maize
improvement in drought-stress tolerance poses a great challenge as
the global need for food and bio-energy increases. Thus, the current
study was planned to explore the variations and determine the
performance of target traits of maize hybrids at grain growth stage
under drought conditions during 2014 under Adana, Mediterranean
climate conditions, Turkey. Maize hybrids (Sancia, Indaco,
71May69, Aaccel, Calgary, 70May82, 72May80) were evaluated
under (irrigated and water stress). Results revealed that, grain yield
and yield traits had a negative effects because of water stress
conditions compared with the normal irrigation. As well as, based on
the result under normal irrigation, the maximum biological yield and
harvest index were recorded. According to the differences among
hybrids were found that, significant differences were observed among
hybrids with respect to yield and yield traits under current research. Based on the results, grain weight had more effect on grain yield
than grain number during grain filling growth stage under water
stress conditions. In this concern, according to low drought
susceptibility index (less grain yield losses), the hybrid (Indaco) was
more stable in grain number and grain weight. Consequently, it may
be concluded that this hybrid would be recommended for use in the
future breeding programs for production of drought tolerant hybrids.
Abstract: Oxygen Reduction Reaction (ORR) performance of
iron and nitrogen co-doped porous carbon nanoparticles (Fe-NPC)
with various physical and (electro) chemical properties have been
investigated. Fe-NPC nanoparticles are synthesized via a facile
soft-templating procedure by using Iron (III) chloride hexa-hydrate as
iron precursor and aminophenol-formaldehyde resin as both carbon
and nitrogen precursor. Fe-NPC nanoparticles shows high surface area
(443.83 m2g-1), high pore volume (0.52 m3g-1), narrow mesopore size
distribution (ca. 3.8 nm), high conductivity (IG/ID=1.04), high kinetic
limiting current (11.71 mAcm-2) and more positive onset potential
(-0.106 V) compared to metal-free NPC nanoparticles (-0.295V)
which make it high efficient ORR metal-free catalysts in alkaline
solution. This study may pave the way of feasibly designing iron and
nitrogen containing carbon materials (Fe-N-C) for highly efficient
oxygen reduction electro-catalysis.
Abstract: One of the most important challenging factors in
medical images is nominated as noise. Image denoising refers to the
improvement of a digital medical image that has been infected by
Additive White Gaussian Noise (AWGN). The digital medical image
or video can be affected by different types of noises. They are
impulse noise, Poisson noise and AWGN. Computed tomography
(CT) images are subjects to low quality due to the noise. Quality of
CT images is dependent on absorbed dose to patients directly in such
a way that increase in absorbed radiation, consequently absorbed
dose to patients (ADP), enhances the CT images quality. In this
manner, noise reduction techniques on purpose of images quality
enhancement exposing no excess radiation to patients is one the
challenging problems for CT images processing. In this work, noise
reduction in CT images was performed using two different
directional 2 dimensional (2D) transformations; i.e., Curvelet and
Contourlet and Discrete Wavelet Transform (DWT) thresholding
methods of BayesShrink and AdaptShrink, compared to each other
and we proposed a new threshold in wavelet domain for not only
noise reduction but also edge retaining, consequently the proposed
method retains the modified coefficients significantly that result good
visual quality. Data evaluations were accomplished by using two
criterions; namely, peak signal to noise ratio (PSNR) and Structure
similarity (Ssim).
Abstract: This paper describes how to dimension the electric
components of a 48V hybrid system considering real customer use.
Furthermore, it provides information about savings in energy and
CO2 emissions by a customer-tailored 48V hybrid. Based on measured customer profiles, the electric units such as the
electric motor and the energy storage are dimensioned. Furthermore,
the CO2 reduction potential in real customer use is determined
compared to conventional vehicles. Finally, investigations are carried
out to specify the topology design and preliminary considerations in
order to hybridize a conventional vehicle with a 48V hybrid system.
The emission model results from an empiric approach also taking into
account the effects of engine dynamics on emissions. We analyzed
transient engine emissions during representative customer driving
profiles and created emission meta models. The investigation showed
a significant difference in emissions when simulating realistic
customer driving profiles using the created verified meta models
compared to static approaches which are commonly used for vehicle
simulation.
Abstract: A sliding door system is used in commercial vehicles
and passenger cars to allow a larger unobstructed access to the
interior for loading and unloading. The movement of a sliding door
on vehicle body is ensured by mechanisms and tracks having special
cross-section which is manufactured by roll forming and stretch
bending process. There are three tracks and three mechanisms which
are called upper, central and lower on a sliding door system. There
are static requirements as strength on different directions, rigidity for
mechanisms, door drop off, door sag; dynamic requirements as high
energy slam opening-closing and durability requirement to validate
these products. In addition, there is a kinematic requirement to find
out force values from door handle during manual operating. In this
study, finite element analysis and physical test results which are
realized for sliding door systems will be shared comparatively.
Abstract: Ultraviolet photocatalytic oxidation (UV-PCO)
technology has been recommended as a green approach to health
indoor environment when it is integrated into mechanical ventilation
systems for inorganic and organic compounds removal as well as
energy saving due to less outdoor air intakes. Although much research
has been devoted to UV-PCO, limited information is available on the
UV-PCO behavior tested by the mixtures in literature. This project
investigated UV-PCO performance and by-product generation using a
single and a mixture of acetone and MEK at 100 ppb each in a
single-pass duct system in an effort to obtain knowledge associated
with competitive photochemical reactions involved in. The
experiments were performed at 20 % RH, 22 °C, and a gas flow rate of
128 m3/h (75 cfm). Results show that acetone and MEK mutually
reduced each other’s PCO removal efficiency, particularly negative
removal efficiency for acetone. These findings were different from
previous observation of facilitatory effects on the adsorption of
acetone and MEK on photocatalyst surfaces.
Abstract: In Automotive Industry, sliding door systems that are
also used as body closures are safety members. Extreme product tests
are realized to prevent failures in design process, but these tests
realized experimentally result in high costs. Finite element analysis is
an effective tool used for design process. These analyses are used
before production of prototype for validation of design according to
customer requirement. In result of this, substantial amount of time
and cost is saved. Finite element model is created for geometries that are designed in
3D CAD programs. Different element types as bar, shell and solid,
can be used for creating mesh model. Cheaper model can be created
by selection of element type, but combination of element type that
was used in model, number and geometry of element and degrees of
freedom affects the analysis result. Sliding door system is a good
example which used these methods for this study. Structural analysis
was realized for sliding door mechanism by using FE models. As
well, physical tests that have same boundary conditions with FE
models were realized. Comparison study for these element types,
were done regarding test and analyses results then optimum
combination was achieved.
Abstract: One of the fundamental characteristics of Information
and Communication Technology (ICT) has been the ever-changing
nature of continuous release and models of ICTs with its impact on
the academic, social, and psychological benefits of its introduction in
schools. However, there seems to be a growing concern about its
negative impact on students when introduced early in schools for
teaching and learning. This study aims to design a model of child
development factors affecting the early introduction of ICTs in
schools in an attempt to improve the understanding of child
development and introduction of ICTs in schools. The proposed
model is based on a sound theoretical framework. It was designed
following a literature review of child development theories and child
development factors. The child development theoretical framework
that fitted to the best of all child development factors was then chosen
as the basis for the proposed model. This study hence found that the
Jean Piaget cognitive developmental theory is the most adequate
theoretical frameworks for modeling child development factors for
ICT introduction in schools.
Abstract: Damaturu is the capital of Yobe State in northeastern
Nigeria where civic amenities and facilities are not adequate even
after 24 years of its existence. The volatile security and political
situations are most significant causes for the same. The basic facility
for the citizens in terms of drinking water and electricity are not
available. For the drinking water, they have to rely on personal
boreholes or the filtered borehole waters available in packaged
sachets in market. The present study is concerned with environmental
impact of indiscriminate disposal of drinking synthetic polythene
water sachets in Damaturu. The sachet water is popularly called as
“pure water”, but its purity is questionable. Increased production and
consumption of sachet water has led to indiscriminate dumping and
disposal of empty sachets leading to serious environmental threat.
The evidence of this is seen for sachets littering the streets and the
drainages blocked by ‘blocks’ of water sachet waste. Sachet water
gained much popularity in Nigeria because the product is convenient
for use, affordable and economically viable. The present study aims
to find out the solution to this environmental problem. The fieldbased
study has found some significant factors that cause
environmental and socio economic effect due to this. Some
recommendations have been made based on research findings
regarding sustainable waste management, recycling and re-use of the
non-biodegradable products in society.