Abstract: In the present research, steam cracking of two types of
feedstocks i.e., naphtha and ethane is simulated for Pyrocrack1-1 and
2/2 coil configurations considering two key parameters of coil outlet
temperature (COT) and coil capacity using a radical based kinetic
model. The computer model is confirmed using the industrial data
obtained from Amirkabir Petrochemical Complex. The results are in
good agreement with performance data for naphtha cracking in a
wide range of severity (0.4-0.7), and for ethane cracking on various
conversions (50-70). It was found that Pyrocrack2-2 coil type is an
appropriate choice for steam cracking of ethane at reasonable
ethylene yield while resulting in much lower tube wall temperature
while Pyrocrack1-1 coil type is a proper selection for liquid
feedstocks i.e. naphtha. It can be used for cracking of liquid
feedstocks at optimal ethylene yield whereas not exceeding the
allowable maximum tube temperature.
Abstract: Arthrobacter viscosus biomass was used for Cr(VI)
biosorption. The effect of pH on Cr(VI) reduction and removal from
aqueous solution was studied in the range of 1-4. The Cr(VI) removal
involves both redox reaction and adsorption of metal ions on biomass
surface. The removal rate of Cr(VI) was enhanced by very acid
conditions, while higher solution pH values favored the removal of
total chromium. The best removal efficiency and uptake were
reached at pH 4, 72.5 % and 12.6 mgCr/gbiomass, respectively.
Abstract: An adaptive Helmholtz resonator was designed and
adapted to hydraulics. The resonator was controlled by open- and
closed-loop controls so that 20 dB attenuation of the peak-to-peak
value of the pulsating pressure was maintained. The closed-loop
control was noted to be better, albeit it was slower because of its low
pressure and temperature variation, which caused variation in the
effective bulk modulus of the hydraulic system. Low-pressure
hydraulics contains air, which affects the stiffness of the hydraulics,
and temperature variation changes the viscosity of the oil. Thus, an
open-loop control loses its efficiency if a condition such as
temperature or the amount of air changes after calibration. The
instability of the low-pressure hydraulic system reduced the
operational frequency range of the Helmholtz resonator when
compared with the results of an analytical model.
Different dampers for hydraulics are presented. Then analytical
models of a hydraulic pipe and a hydraulic pipe with a Helmholtz
resonator are presented. The analytical models are based on the wave
equation of sound pressure. Finally, control methods and the results
of experiments are presented.
Abstract: In this paper, we apply the FM methodology to the
cross-section of Romanian-listed common stocks and investigate the
explanatory power of market beta on the cross-section of commons
stock returns from Bucharest Stock Exchange. Various assumptions
are empirically tested, such us linearity, market efficiency, the “no
systematic effect of non-beta risk" hypothesis or the positive
expected risk-return trade-off hypothesis. We find that the Romanian
stock market shows the same properties as the other emerging
markets in terms of efficiency and significance of the linear riskreturn
models. Our analysis included weekly returns from January
2002 until May 2010 and the portfolio formation, estimation and
testing was performed in a rolling manner using 51 observations (one
year) for each stage of the analysis.
Abstract: This current research focused on development of degradable starch based packaging film with enhanced mechanical properties. A series of low density polyethylene (LDPE)/tapioca starch compounds with various tapioca starch contents were prepared by twin screw extrusion with the addition of maleic anhydride grafted polyethylene as compatibilizer. Palm cooking oil was used as processing aid to ease the blown film process, thus, degradable film can be processed via conventional blown film machine. Studies on their characteristics, mechanical properties and biodegradation were carried out by Fourier Transform Infrared (FTIR) spectroscopy and optical properties, tensile test and exposure to fungi environment respectively. The presence of high starch contents had an adverse effect on the tensile properties of LDPE/tapioca starch blends. However, the addition of compatibilizer to the blends improved the interfacial adhesion between the two materials, hence, improved the tensile properties of the films. High content of starch amount also was found to increase the rate of biodegradability of LDPE/tapioca starch films. It can be proved by exposure of the film to fungi environment. A growth of microbes colony can be seen on the surface of LDPE/tapioca starch film indicates that the granular starch present on the surface of the polymer film is attacked by microorganisms, until most of it is assimilated as a carbon source.
Abstract: Electrical resistivity is a fundamental parameter of metals or electrical conductors. Since resistivity is a function of temperature, in order to completely understand the behavior of metals, a temperature dependent theoretical model is needed. A model based on physics principles has recently been developed to obtain an equation that relates electrical resistivity to temperature. This equation is dependent upon a parameter associated with the electron travel time before being scattered, and a parameter that relates the energy of the atoms and their separation distance. Analysis of the energy parameter reveals that the equation is optimized if the proportionality term in the equation is not constant but varies over the temperature range. Additional analysis reveals that the theoretical equation can be used to determine the mean free path of conduction electrons, the number of defects in the atomic lattice, and the ‘equivalent’ charge associated with the metallic bonding of the atoms. All of this analysis provides validation for the theoretical model and provides insight into the behavior of metals where performance is affected by temperatures (e.g., integrated circuits and temperature sensors).
Abstract: To simulate heating systems in buildings, a research oriented computer code has been developed in Sharif University of Technology in Iran where the climate, existing heating equipment in buildings, consumer behavior and their interactions are considered for simulating energy consumption in conventional systems such as heaters, radiators and fan-coils. In order to validate the computer code, the available data of five buildings was used and the computed consumed energy was compared with the estimated energy extracted from monthly bills. The initial heating system was replaced by the alternative system and the effect of this change was observed on the energy consumption. As a result, the effect of changing heating equipment on energy consumption was investigated in different climates. Changing heater to radiator renders energy conservation up to 50% in all climates and changing radiator to fan-coil decreases energy consumption in climates with cold and dry winter.
Abstract: Sorghum flour was supplemented with 15 and 30%
chickpea flour. Sorghum flour and the supplement were fermented at
35 oC for 0, 8, 16, and 24 h. Changes in pH, titrable acidity, total
soluble solids, protein content, in vitro protein digestibility and
amino acid composition were investigated during fermentation and/or
after supplementation of sorghum flour with chickpea. The pH of the
fermenting material decreased sharply with a concomitant increase in
the titrable acidity. The total soluble solids remained unchanged with
progressive fermentation time. The protein content of sorghum
cultivar was found to be 9.27 and that of chickpea was 22.47%. The
protein content of sorghum cultivar after supplementation with15 and
30% chickpea was significantly (P ≤ 0.05) increased to 11.78 and
14.55%, respectively. The protein digestibility also increased after
fermentation from 13.35 to 30.59 and 40.56% for the supplements,
respectively. Further increment in protein content and digestibility
was observed when supplemented and unsupplemented samples were
fermented for different periods of time. Cooking of fermented
samples was found to increase the protein content slightly and
decreased digestibility for both supplements. Amino acid content of
fermented and fermented and cooked supplements was determined.
Supplementation was found to increase the lysine and therionine
content. Cooking following fermentation decreased lysine,
isoleucine, valine and sulfur containg amino acids.
Abstract: Group work, projects and discussions are important
components of teacher education courses whether they are face-toface,
blended or exclusively online formats. This paper examines the varieties of tasks and challenges with this learning format in a face to
face class teacher education class providing specific examples of both
failure and success from both the student and instructor perspective.
The discussion begins with a brief history of collaborative and cooperative learning, moves to an exploration of the promised
benefits and then takes a look at some of the challenges which can
arise specifically from the use of new technologies. The discussion concludes with guidelines and specific suggestions.
Abstract: The experiment was performed to evaluate the effect
of GA3, 2,4-D on fruit growth and fruit quality of wax apple. The
experiment consisted of Red A, Monulla, Atu, Red B cultivars. GA3
and 2,4-D were applied at the small bud and petal fall stage.
Physiological, biochemical characters of fruit were recoded. The
result showed application of GA3, 2,4-D greatly response in
increasing fruit set for all treatment as compared to control. Fruit
weight, fruit size were increased at 10 ppm 2,4-D in ‘Red A’, ‘Red
B’, however it was also enhancing at 10 ppm GA3 in ‘Monulla’,
‘Atu’. For ‘Monulla’, ‘Atu’ fruit crack reduced by 10 ppm 2,4-D
application, but ‘Red B’, ‘Red A’ gave least fruit crack at 10 and 30
ppm GA3, respectively. ‘Monulla’, ‘Atu’ and ‘Red B’ resulted in
response well to 10 ppm GA3 on improving TSS, whereas
application of 30 ppm GA3 greatly enhancing TSS in ‘Red A’. For
‘Atu’ titratable acidity markedly reduced by 10 ppm GA3
application, but spraying with 30 ppm GA3 greatly response in
reducing titratable acidity in ‘Red A’, ‘Red B’ and ‘Monulla’. It was
concluded that GA3, 2,4-D can be an effective tool to enhancing fruit
set, fruit growth as well as improving fruit quality of wax apple.
Abstract: Prolonged immobilization leads to significant
weakness and atrophy of the skeletal muscle and can also impair the
recovery of muscle strength following injury. Therefore, it is
important to minimize the period under immobilization and accelerate
the return to normal activity. This study examined the effects of heat
treatment and rest-inserted exercise on the muscle activity of the lower
limb during knee flexion/extension. Twelve healthy subjects were
assigned to 4 groups that included: (1) heat treatment + rest-inserted
exercise; (2) heat + continuous exercise; (3) no heat + rest-inserted
exercise; and (4) no heat + continuous exercise. Heat treatment was
applied for 15 mins prior to exercise. Continuous exercise groups
performed knee flexion/extension at 0.5 Hz for 300 cycles without rest
whereas rest-inserted exercise groups performed the same exercise but
with 2 mins rest inserted every 60 cycles of continuous exercise.
Changes in the rectus femoris and hamstring muscle activities were
assessed at 0, 1, and 2 weeks of treatment by measuring the
electromyography signals of isokinetic maximum voluntary
contraction. Significant increases in both the rectus femoris and
hamstring muscles were observed after 2 weeks of treatment only
when both heat treatment and rest-inserted exercise were performed.
These results suggest that combination of various treatment techniques,
such as heat treatment and rest-inserted exercise, may expedite the
recovery of muscle strength following immobilization.
Abstract: CFD simulations are carried out in arterial stenoses
with 48 % areal occlusion. Non-newtonian fluid model is selected for
the blood flow as the same problem has been solved before with
Newtonian fluid model. Studies on flow resistance with the presence
of surface irregularities are carried out. Investigations are also
performed on the pressure drop at various Reynolds numbers. The
present study revealed that the pressure drop across a stenosed artery
is practically unaffected by surface irregularities at low Reynolds
numbers, while flow features are observed and discussed at higher
Reynolds numbers.
Abstract: This study extends research on the relationship
between marketing strategy and market segmentation by
investigating on market segments in the cement industry.
Competitive strength and rivals distance from the factory were used
as business environment. A three segment (positive, neutral or
indifferent and zero zones) were identified as strategic segments. For
each segment a marketing strategy (aggressive, defensive and
decline) were developed. This study employed data from cement
industry to fulfill two objectives, the first is to give a framework to
the segmentation of cement industry and the second is developing
marketing strategy with varying competitive strength. Fifty six
questionnaires containing close-and open-ended questions were
collected and analyzed. Results supported the theory that segments
tend to be more aggressive than defensive when competitive strength
increases. It is concluded that high strength segments follow total
market coverage, concentric diversification and frontal attack to their
competitors. With decreased competitive strength, Business tends to
follow multi-market strategy, product modification/improvement and
flank attack to direct competitors for this kind of segments. Segments
with weak competitive strength followed focus strategy and decline
strategy.
Abstract: Along with forward supply chain organization needs
to consider the impact of reverse logistics due to its economic
advantage, social awareness and strict legislations. In this paper, we
develop a system dynamics framework for a closed-loop supply
chain with fuzzy demand and fuzzy collection rate by incorporating
product exchange policy in forward channel and various recovery
options in reverse channel. The uncertainty issues associated with
acquisition and collection of used product have been quantified using
possibility measures. In the simulation study, we analyze order
variation at both retailer and distributor level and compare bullwhip
effects of different logistics participants over time between the
traditional forward supply chain and the closed-loop supply chain.
Our results suggest that the integration of reverse logistics can reduce
order variation and bullwhip effect of a closed-loop system. Finally,
sensitivity analysis is performed to examine the impact of various
parameters on recovery process and bullwhip effect.
Abstract: When programming in languages such as C, Java, etc.,
it is difficult to reconstruct the programmer's ideas only from the
program code. This occurs mainly because, much of the programmer's
ideas behind the implementation are not recorded in the code during
implementation. For example, physical aspects of computation such as
spatial structures, activities, and meaning of variables are not required
as instructions to the computer and are often excluded. This makes the
future reconstruction of the original ideas difficult. AIDA, which is a
multimedia programming language based on the cyberFilm model, can
solve these problems allowing to describe ideas behind programs
using advanced annotation methods as a natural extension to
programming. In this paper, a development environment that
implements the AIDA language is presented with a focus on the
annotation methods. In particular, an actual scientific numerical
computation code is created and the effects of the annotation methods
are analyzed.
Abstract: Context awareness is a capability whereby mobile
computing devices can sense their physical environment and adapt
their behavior accordingly. The term context-awareness, in
ubiquitous computing, was introduced by Schilit in 1994 and has
become one of the most exciting concepts in early 21st-century
computing, fueled by recent developments in pervasive computing
(i.e. mobile and ubiquitous computing). These include computing
devices worn by users, embedded devices, smart appliances, sensors
surrounding users and a variety of wireless networking technologies.
Context-aware applications use context information to adapt
interfaces, tailor the set of application-relevant data, increase the
precision of information retrieval, discover services, make the user
interaction implicit, or build smart environments. For example: A
context aware mobile phone will know that the user is currently in a
meeting room, and reject any unimportant calls. One of the major
challenges in providing users with context-aware services lies in
continuously monitoring their contexts based on numerous sensors
connected to the context aware system through wireless
communication. A number of context aware frameworks based on
sensors have been proposed, but many of them have neglected the
fact that monitoring with sensors imposes heavy workloads on
ubiquitous devices with limited computing power and battery. In this
paper, we present CALEEF, a lightweight and energy efficient
context aware framework for resource limited ubiquitous devices.
Abstract: The current study describes a multi-objective optimization technique for positioning of houses in a residential neighborhood. The main task is the placement of residential houses in a favorable configuration satisfying a number of objectives. Solving the house layout problem is a challenging task. It requires an iterative approach to satisfy design requirements (e.g. energy efficiency, skyview, daylight, roads network, visual privacy, and clear access to favorite views). These design requirements vary from one project to another based on location and client preferences. In the Gulf region, the most important socio-cultural factor is the visual privacy in indoor space. Hence, most of the residential houses in this region are surrounded by high fences to provide privacy, which has a direct impact on other requirements (e.g. daylight and direction to favorite views). This investigation introduces a novel technique to optimally locate and orient residential buildings to satisfy a set of design requirements. The developed technique explores the search space for possible solutions. This study considers two dimensional house planning problems. However, it can be extended to solve three dimensional cases.
Abstract: In this paper the General Game problem is described.
In this problem the competition or cooperation dilemma occurs as the
two basic types of strategies. The strategy possibilities have been
analyzed for finding winning strategy in uncertain situations (no
information about the number of players and their strategy types).
The winning strategy is missing, but a good solution can be found by
simulation by varying the ratio of the two types of strategies. This
new method has been used in a real contest with human players,
where the created strategies by simulation have reached very good
ranks. This construction can be applied in other real social games as
well.
Abstract: Finger spelling is an art of communicating by signs
made with fingers, and has been introduced into sign language to serve
as a bridge between the sign language and the verbal language.
Previous approaches to finger spelling recognition are classified into
two categories: glove-based and vision-based approaches. The
glove-based approach is simpler and more accurate recognizing work
of hand posture than vision-based, yet the interfaces require the user to
wear a cumbersome and carry a load of cables that connected the
device to a computer. In contrast, the vision-based approaches provide
an attractive alternative to the cumbersome interface, and promise
more natural and unobtrusive human-computer interaction. The
vision-based approaches generally consist of two steps: hand
extraction and recognition, and two steps are processed independently.
This paper proposes real-time vision-based Korean finger spelling
recognition system by integrating hand extraction into recognition.
First, we tentatively detect a hand region using CAMShift algorithm.
Then fill factor and aspect ratio estimated by width and height
estimated by CAMShift are used to choose candidate from database,
which can reduce the number of matching in recognition step. To
recognize the finger spelling, we use DTW(dynamic time warping)
based on modified chain codes, to be robust to scale and orientation
variations. In this procedure, since accurate hand regions, without
holes and noises, should be extracted to improve the precision, we use
graph cuts algorithm that globally minimize the energy function
elegantly expressed by Markov random fields (MRFs). In the
experiments, the computational times are less than 130ms, and the
times are not related to the number of templates of finger spellings in
database, as candidate templates are selected in extraction step.
Abstract: Dielectric sheet perturbation to the dominant TE111
mode resonant frequency of a circular cavity is studied and presented
in this paper. The dielectric sheet, placed at the middle of the airfilled
cavity, introduces discontinuities and disturbs the configuration
of electromagnetic fields in the cavity. For fixed dimensions of cavity
and fixed thickness of the loading dielectric, the dominant resonant
frequency varies quite linearly with the permittivity of the dielectric.
This quasi-linear relationship is plotted using Maple software and
verified using 3D electromagnetic simulations. Two probes are used
in the simulation for wave excitation into and from the cavity. The
best length of probe is found to be 3 mm, giving the closest resonant
frequency to the one calculated using Maple. A total of fourteen
different dielectrics of permittivity ranging from 1 to 12.9 are tested
one by one in the simulation. The works show very close agreement
between the results from Maple and the simulation. A constant
difference of 0.04 GHz is found between the resonant frequencies
collected during simulation and the ones from Maple. The success of
this project may lead to the possibility of using the middle loaded
cavity at TE111 mode as a microwave non-destructive testing of solid
materials.