Abstract: This paper presents a new method to detect high impedance faults in radial distribution systems. Magnitudes of third and fifth harmonic components of voltages and currents are used as a feature vector for fault discrimination. The proposed methodology uses a learning vector quantization (LVQ) neural network as a classifier for identifying high impedance arc-type faults. The network learns from the data obtained from simulation of a simple radial system under different fault and system conditions. Compared to a feed-forward neural network, a properly tuned LVQ network gives quicker response.
Abstract: In the process of polyethylene extrusion polymer
material similar to powder or granule is under compression, melting
and transmission operation and on base of special form, extrudate has
been produced. Twin-screw extruders are applicable in industries
because of their high capacity. The powder mixing with chemical
additives and melting with thermal and mechanical energy in three
zones (feed, compression and metering zone) and because of gear
pump and screw's pressure, converting to final product in latest plate.
Extruders with twin-screw and short distance between screws are
better than other types because of their high capacity and good
thermal and mechanical stress.
In this paper, process of polyethylene extrusion and various tapes
of extruders are studied. It is necessary to have an exact control on
process to producing high quality products with safe operation and
optimum energy consumption.
The granule size is depending on granulator motor speed. Results
show at constant feed rate a decrease in granule size was found whit
Increase in motor speed. Relationships between HDPE feed rate and
speed of granulator motor, main motor and gear pump are calculated
following as:
x = HDPE feed flow rate, yM = Main motor speed
yM = (-3.6076e-3) x^4+ (0.24597) x^3+ (-5.49003) x^2+ (64.22092)
x+61.66786 (1)
x = HDPE feed flow rate, yG = Gear pump speed
yG = (-2.4996e-3) x^4+ (0.18018) x^3+ (-4.22794) x^2+ (48.45536)
x+18.78880 (2)
x = HDPE feed flow rate, y = Granulator motor speed
10th Degree Polynomial Fit: y = a+bx+cx^2+dx^3... (3)
a = 1.2751, b = 282.4655, c = -165.2098,
d = 48.3106, e = -8.18715, f = 0.84997
g = -0.056094, h = 0.002358, i = -6.11816e-5
j = 8.919726e-7, k = -5.59050e-9
Abstract: This paper presents the results related to the
interference reduction technique in multistage multiuser detector for
asynchronous DS-CDMA system. To meet the real-time
requirements for asynchronous multiuser detection, a bit streaming,
cascade architecture is used. An asynchronous multiuser detection
involves block-based computations and matrix inversions. The paper
covers iterative-based suboptimal schemes that have been studied to
decrease the computational complexity, eliminate the need for matrix
inversions, decreases the execution time, reduces the memory
requirements and uses joint estimation and detection process that
gives better performance than the independent parameter estimation
method. The stages of the iteration use cascaded and bits processed
in a streaming fashion. The simulation has been carried out for
asynchronous DS-CDMA system by varying one parameter, i.e.,
number of users. The simulation result exhibits that system gives
optimum bit error rate (BER) at 3rd stage for 15-users.
Abstract: This article presents the development of a neural
network cognitive model for the classification and detection of
different frequency signals. The basic structure of the implemented
neural network was inspired on the perception process that humans
generally make in order to visually distinguish between high and low
frequency signals. It is based on the dynamic neural network concept,
with delays. A special two-layer feedforward neural net structure was
successfully implemented, trained and validated, to achieve
minimum target error. Training confirmed that this neural net
structure descents and converges to a human perception classification
solution, even when far away from the target.
Abstract: Interactive web-based computer simulations are
needed by the medical community to replicate the experience of
surgical procedures as closely and realistically as possible without
the need to practice on corpses, animals and/or plastic models. In this
paper, we offer a review on current state of the research on
simulations of surgical threads, identify future needs and present our
proposed plans to meet them. Our goal is to create a physics-based
simulator, which will predict the behavior of surgical thread when
subjected to conditions commonly encountered during surgery. To
that end, we will i) develop three dimensional finite element models
based on the Cosserat theory of elasticity ii) test and feedback results
with the medical community and iii) develop a web-based user
interface to run/command our simulator and visualize the results. The
impacts of our research are that i) it will contribute to the
development of a new generation of training for medical school
students and ii) the simulator will be useful to expert surgeons in
developing new, better and less risky procedures.
Abstract: This study was conducted to investigate the optimum
levels of glutamine (Gln) supplementation in broiler diets. A total of
32 one-day-old male chicks with initial body weight 41.5 g were
segregated into 4 groups (8 chicks per group) and subsequently
distributed to individual cages. Feed and water were provided ad
libitum for 21 days. Four dietary treatments were as follows: control
and supplemented Gln at 1, 2 and 3%, respectively. The results found
that the addition Gln had no negative effects on dry matter, organic
matter, ash digestibility or nitrogen retention. Birds fed with 1% Gln
had significantly higher villi wide and villi height : crypt depth ratio
in duodenum than the control chicks and 2 and 3% Gln chicks. It is
suggested that the addition of Gln at 1% indicated a beneficial effect
on improving small intestinal morphology, in addition Gln may
stimulate immune organ development of broiler chickens.
Abstract: This paper presents an efficient algorithm for
optimization of radial distribution systems by a network
reconfiguration to balance feeder loads and eliminate overload
conditions. The system load-balancing index is used to determine the
loading conditions of the system and maximum system loading
capacity. The index value has to be minimum in the optimal network
reconfiguration of load balancing. A method based on Tabu search
algorithm, The Tabu search algorithm is employed to search for the
optimal network reconfiguration. The basic idea behind the search is
a move from a current solution to its neighborhood by effectively
utilizing a memory to provide an efficient search for optimality. It
presents low computational effort and is able to find good quality
configurations. Simulation results for a radial 69-bus system with
distributed generations and capacitors placement. The study results
show that the optimal on/off patterns of the switches can be identified
to give the best network reconfiguration involving balancing of
feeder loads while respecting all the constraints.
Abstract: In a pilot plant scale of a fluidized bed reactor, a
reduction reaction of sodium sulfate by natural gas has been
investigated. Natural gas is applied in this study as a reductant. Feed
density, feed mass flow rate, natural gas and air flow rate
(independent parameters)and temperature of bed and CO
concentration in inlet and outlet of reactor (dependent parameters)
were monitored and recorded at steady state. The residence time was
adjusted close to value of traditional reaction [1]. An artificial neural
network (ANN) was established to study dependency of yield and
carbon gradient on operating parameters. Resultant 97% accuracy of
applied ANN is a good prove that natural gas can be used as a
reducing agent. Predicted ANN model for relation between other
sources carbon gradient (accuracy 74%) indicates there is not a
meaningful relation between other sources carbon variation and
reduction process which means carbon in granule does not have
significant effect on the reaction yield.
Abstract: Where renewable energy sources, solar, hydro, wind are available the remote communities and businesses can be provided with the most reliable and affordable source of electrical energy. This paper presents a model of safari rest contains all the necessary services for the interested tourists who visit the safari Sinai desert. The PV energy system provides the rural energy needs of remote communities. A photovoltaic renewable energy system is designed to feed the global Ac and Dc electrical required load of this safari rest . The benefits of photovoltaic renewable energy at rural applications are its versatility and convenience. This model of safari rest must be taken in consideration by Egyptian Government as it will provide the tourism plane by new interested tourism field which put a big spot on Red sea area: El Ghordaka.
Abstract: Team efficacy beliefs show promise in enhancing
team performance. Using a model-based quantitative research design,
we investigated the antecedents and performance consequences of
generalized team efficacy (potency) in a sample of 56 capital projects
executed by 15 Fortune 500 companies in the process industries.
Empirical analysis of our field survey identified that generalized
team efficacy beliefs were positively associated with an objective
measure of project cost performance. Regression analysis revealed
that team competence, empowering leadership, and performance
feedback all predicted generalized team efficacy beliefs. Tests of
mediation revealed that generalized team efficacy fully mediated
between these three inputs and project cost performance.
Abstract: Fuel cells have become one of the major areas of
research in the academia and the industry. The goal of most fish
farmers is to maximize production and profits while holding labor
and management efforts to the minimum. Risk of fish kills, disease
outbreaks, poor water quality in most pond culture operations,
aeration offers the most immediate and practical solution to water
quality problems encountered at higher stocking and feeding rates.
Many units of aeration system are electrical units so using a
continuous, high reliability, affordable, and environmentally friendly
power sources is necessary. Aeration of water by using PEM fuel cell
power is not only a new application of the renewable energy, but
also, it provides an affordable method to promote biodiversity in
stagnant ponds and lakes. This paper presents a new design and
control of PEM fuel cell powered a diffused air aeration system for a
shrimp farm in Mersa Matruh in Egypt. Also Artificial intelligence
(AI) techniques control is used to control the fuel cell output power
by control input gases flow rate. Moreover the mathematical
modeling and simulation of PEM fuel cell is introduced. A
comparison study is applied between the performance of fuzzy logic
control (FLC) and neural network control (NNC). The results show
the effectiveness of NNC over FLC.
Abstract: The distillation process in the general sense is a
relatively simple technique from the standpoints of its principles.
When dedicating distillation to water treatment and specifically
producing fresh water from sea, ocean and/ briny waters it is
interesting to notice that distillation has no limitations or domains of
applicability regarding the nature or the type of the feedstock water.
This is not the case however for other techniques that are
technologically quite complex, necessitate bigger capital investments
and are limited in their usability. In a previous paper we have
explored some of the effects of temperature on yield. In this paper,
we continue building onto that knowledge base and focus on the
effects of several additional engineering and design variables on
productivity.
Abstract: Since the presentation of the backpropagation algorithm, a vast variety of improvements of the technique for training a feed forward neural networks have been proposed. This article focuses on two classes of acceleration techniques, one is known as Local Adaptive Techniques that are based on weightspecific only, such as the temporal behavior of the partial derivative of the current weight. The other, known as Dynamic Adaptation Methods, which dynamically adapts the momentum factors, α, and learning rate, η, with respect to the iteration number or gradient. Some of most popular learning algorithms are described. These techniques have been implemented and tested on several problems and measured in terms of gradient and error function evaluation, and percentage of success. Numerical evidence shows that these techniques improve the convergence of the Backpropagation algorithm.
Abstract: This paper presents a method of reducing the feedback
delay time of DWA(Data Weighted Averaging) used in sigma-delta
modulators. The delay time reduction results from the elimination of
the latch at the quantizer output and also from the falling edge
operation. The designed sigma-delta modulator improves the timing
margin about 16%. The sub-circuits of sigma-delta modulator such as
SC(Switched Capacitor) integrator, 9-level quantizer, comparator, and
DWA are designed with the non-ideal characteristics taken into
account. The sigma-delta modulator has a maximum SNR (Signal to
Noise Ratio) of 84 dB or 13 bit resolution.
Abstract: This paper presents an approach for the determination of the optimal cutting parameters (spindle speed, feed rate, depth of cut and engagement) leading to minimum surface roughness in face milling of high silicon stainless steel by coupling neural network (NN) and Electromagnetism-like Algorithm (EM). In this regard, the advantages of statistical experimental design technique, experimental measurements, artificial neural network, and Electromagnetism-like optimization method are exploited in an integrated manner. To this end, numerous experiments on this stainless steel were conducted to obtain surface roughness values. A predictive model for surface roughness is created by using a back propogation neural network, then the optimization problem was solved by using EM optimization. Additional experiments were performed to validate optimum surface roughness value predicted by EM algorithm. It is clearly seen that a good agreement is observed between the predicted values by EM coupled with feed forward neural network and experimental measurements. The obtained results show that the EM algorithm coupled with back propogation neural network is an efficient and accurate method in approaching the global minimum of surface roughness in face milling.
Abstract: In this paper comparison of Reflector Antenna
analyzing techniques based on wave and ray nature of optics is
presented for an offset reflector antenna using GRASP (General
Reflector antenna Analysis Software Package) software. The results
obtained using PO (Physical Optics), PTD (Physical theory of
Diffraction), and GTD (Geometrical Theory of Diffraction) are
compared. The validity of PO and GTD techniques in regions around
the antenna, caustic behavior of GTD in main beam, and deviation of
GTD in case of near-in sidelobes of radiation pattern are discussed.
The comparison for far-out sidelobes predicted by PO, PO + PTD
and GTD is described. The effect of Direct Radiations from feed
which results in feed selection for the system is addressed.
Abstract: One of the most attractive and important field of chaos theory is control of chaos. In this paper, we try to present a simple framework for chaotic motion control using the feedback linearization method. Using this approach, we derive a strategy, which can be easily applied to the other chaotic systems. This task presents two novel results: the desired periodic orbit need not be a solution of the original dynamics and the other is the robustness of response against parameter variations. The illustrated simulations show the ability of these. In addition, by a comparison between a conventional state feedback and our proposed method it is demonstrated that the introduced technique is more efficient.
Abstract: The paper presents a novel method for the 3D shaping
of different materials using a high-pressure abrasive water jet and a
flat target image. For steering movement process of the jet a principle
similar to raster image way of record and readout was used.
However, respective colors of pixel of such a bitmap are connected
with adequate jet feed rate that causes erosion of material with
adequate depth. Thanks to that innovation, one can observe spatial
imaging of the object. Theoretical basis as well as spatial model of
material shaping and experimental stand including steering program
are presented in. There are also presented methodic and some
experimental erosion results as well as practical example of object-s
bas-relief made of metal.
Abstract: We present here the results for a comparative study of
some techniques, available in the literature, related to the relevance
feedback mechanism in the case of a short-term learning. Only one
method among those considered here is belonging to the data mining
field which is the K-nearest neighbors algorithm (KNN) while the
rest of the methods is related purely to the information retrieval field
and they fall under the purview of the following three major axes:
Shifting query, Feature Weighting and the optimization of the
parameters of similarity metric. As a contribution, and in addition to
the comparative purpose, we propose a new version of the KNN
algorithm referred to as an incremental KNN which is distinct from
the original version in the sense that besides the influence of the
seeds, the rate of the actual target image is influenced also by the
images already rated. The results presented here have been obtained
after experiments conducted on the Wang database for one iteration
and utilizing color moments on the RGB space. This compact
descriptor, Color Moments, is adequate for the efficiency purposes
needed in the case of interactive systems. The results obtained allow
us to claim that the proposed algorithm proves good results; it even
outperforms a wide range of techniques available in the literature.
Abstract: This paper presents how the real-time chatter
prevention can be realized by feedback of acoustic cutting signal, and
the efficacy of the proposed adaptive spindle speed tuning algorithm is
verified by intensive experimental simulations. A pair of
microphones, perpendicular to each other, is used to acquire the
acoustic cutting signal resulting from milling chatter. A real-time
feedback control loop is constructed for spindle speed compensation
so that the milling process can be ensured to be within the stability
zone of stability lobe diagram. Acoustic Chatter Signal Index (ACSI)
and Spindle Speed Compensation Strategy (SSCS) are proposed to
quantify the acoustic signal and actively tune the spindle speed
respectively. By converting the acoustic feedback signal into ACSI,
an appropriate Spindle Speed Compensation Rate (SSCR) can be
determined by SSCS based on real-time chatter level or ACSI.
Accordingly, the compensation command, referred to as Added-On
Voltage (AOV), is applied to increase/decrease the spindle motor
speed. By inspection on the precision and quality of the workpiece
surface after milling, the efficacy of the real-time chatter prevention
strategy via acoustic signal feedback is further assured.