Abstract: Single-pole switching scheme is widely used in the
Extra High Voltage system. However, the substantial negativesequence
current injected to the turbine-generators imposes the
electromagnetic (E/M) torque of double system- frequency
components during the dead time (between single-pole clearing and
line reclosing). This would induce supersynchronous resonance
(SPSR) torque amplifications on low pressure turbine generator
blades and even lead to fatigue damage. This paper proposes the
design of a mechanical filter (MF) with natural frequency close to
double-system frequency. From the simulation results, it is found that
such a filter not only successfully damps the resonant effect, but also
has the characteristics of feasibility and compact.
Abstract: The modern telecommunication industry demands
higher capacity networks with high data rate. Orthogonal frequency
division multiplexing (OFDM) is a promising technique for high data
rate wireless communications at reasonable complexity in wireless
channels. OFDM has been adopted for many types of wireless
systems like wireless local area networks such as IEEE 802.11a, and
digital audio/video broadcasting (DAB/DVB). The proposed research
focuses on a concatenated coding scheme that improve the
performance of OFDM based wireless communications. It uses a
Redundant Residue Number System (RRNS) code as the outer code
and a convolutional code as the inner code. Here, a direct conversion
of analog signal to residue domain is done to reduce the conversion
complexity using sigma-delta based parallel analog-to-residue
converter. The bit error rate (BER) performances of the proposed
system under different channel conditions are investigated. These
include the effect of additive white Gaussian noise (AWGN),
multipath delay spread, peak power clipping and frame start
synchronization error. The simulation results show that the proposed
RRNS-Convolutional concatenated coding (RCCC) scheme provides
significant improvement in the system performance by exploiting the
inherent properties of RRNS.
Abstract: Selection of maize (Zea mays) hybrids with wide adaptability across diverse farming environments is important, prior to recommending them to achieve a high rate of hybrid adoption. Grain yield of 14 maize hybrids, tested in a randomized completeblock design with four replicates across 22 environments in Iran, was analyzed using site regression (SREG) stability model. The biplot technique facilitates a visual evaluation of superior genotypes, which is useful for cultivar recommendation and mega-environment identification. The objectives of this study were (i) identification of suitable hybrids with both high mean performance and high stability (ii) to determine mega-environments for maize production in Iran. Biplot analysis identifies two mega-environments in this study. The first mega-environments included KRM, KSH, MGN, DZF A, KRJ, DRB, DZF B, SHZ B, and KHM, where G10 hybrid was the best performing hybrid. The second mega-environment included ESF B, ESF A, and SHZ A, where G4 hybrid was the best hybrid. According to the ideal-hybrid biplot, G10 hybrid was better than all other hybrids, followed by the G1 and G3 hybrids. These hybrids were identified as best hybrids that have high grain yield and high yield stability. GGE biplot analysis provided a framework for identifying the target testing locations that discriminates genotypes that are high yielding and stable.
Abstract: Crucial information barely visible to the human eye is
often embedded in a series of low resolution images taken of the
same scene. Super resolution reconstruction is the process of
combining several low resolution images into a single higher
resolution image. The ideal algorithm should be fast, and should add
sharpness and details, both at edges and in regions without adding
artifacts. In this paper we propose a super resolution blind
reconstruction technique for linearly degraded images. In our
proposed technique the algorithm is divided into three parts an image
registration, wavelets based fusion and an image restoration. In this
paper three low resolution images are considered which may sub
pixels shifted, rotated, blurred or noisy, the sub pixel shifted images
are registered using affine transformation model; A wavelet based
fusion is performed and the noise is removed using soft thresolding.
Our proposed technique reduces blocking artifacts and also
smoothens the edges and it is also able to restore high frequency
details in an image. Our technique is efficient and computationally
fast having clear perspective of real time implementation.
Abstract: In this paper we present a novel approach for human
Body configuration based on the Silhouette. We propose to address
this problem under the Bayesian framework. We use an effective
Model based MCMC (Markov Chain Monte Carlo) method to solve
the configuration problem, in which the best configuration could be
defined as MAP (maximize a posteriori probability) in Bayesian
model. This model based MCMC utilizes the human body model to
drive the MCMC sampling from the solution space. It converses the
original high dimension space into a restricted sub-space constructed
by the human model and uses a hybrid sampling algorithm. We
choose an explicit human model and carefully select the likelihood
functions to represent the best configuration solution. The
experiments show that this method could get an accurate
configuration and timesaving for different human from multi-views.
Abstract: This study was investigated on sampling and
analyzing water quality in water reservoir & water tower installed in
two kind of residential buildings and school facilities. Data of water
quality was collected for correlation analysis with frequency of
sanitization of water reservoir through questioning managers of
building about the inspection charts recorded on equipment for water
reservoir. Statistical software packages (SPSS) were applied to the
data of two groups (cleaning frequency and water quality) for
regression analysis to determine the optimal cleaning frequency of
sanitization. The correlation coefficient (R) in this paper represented
the degree of correlation, with values of R ranging from +1 to -1.After
investigating three categories of drinking water users; this study found
that the frequency of sanitization of water reservoir significantly
influenced the water quality of drinking water. A higher frequency of
sanitization (more than four times per 1 year) implied a higher quality
of drinking water. Results indicated that sanitizing water reservoir &
water tower should at least twice annually for achieving the aim of
safety of drinking water.
Abstract: PCCI engines can reduce NOx and PM emissions
simultaneously without sacrificing thermal efficiency, but a low
combustion temperature resulting from early fuel injection, and
ignition occurring prior to TDC, can cause higher THC and CO
emissions and fuel consumption. In conclusion, it was found that the
PCCI combustion achieved by the 2-stage injection strategy with
optimized calibration factors (e.g. EGR rate, injection pressure, swirl
ratio, intake pressure, injection timing) can reduce NOx and PM
emissions simultaneously. This research works are expected to
provide valuable information conducive to a development of an
innovative combustion engine that can fulfill upcoming stringent
emission standards.
Abstract: In single trial analysis, when using Principal
Component Analysis (PCA) to extract Visual Evoked Potential
(VEP) signals, the selection of principal components (PCs) is an
important issue. We propose a new method here that selects only
the appropriate PCs. We denote the method as selective eigen-rate
(SER). In the method, the VEP is reconstructed based on the rate
of the eigen-values of the PCs. When this technique is applied on
emulated VEP signals added with background
electroencephalogram (EEG), with a focus on extracting the
evoked P3 parameter, it is found to be feasible. The improvement
in signal to noise ratio (SNR) is superior to two other existing
methods of PC selection: Kaiser (KSR) and Residual Power (RP).
Though another PC selection method, Spectral Power Ratio (SPR)
gives a comparable SNR with high noise factors (i.e. EEGs), SER
give more impressive results in such cases. Next, we applied SER
method to real VEP signals to analyse the P3 responses for
matched and non-matched stimuli. The P3 parameters extracted
through our proposed SER method showed higher P3 response for
matched stimulus, which confirms to the existing neuroscience
knowledge. Single trial PCA using KSR and RP methods failed to
indicate any difference for the stimuli.
Abstract: In this paper we propose a family of algorithms based
on 3rd and 4th order cumulants for blind single-input single-output
(SISO) Non-Minimum Phase (NMP) Finite Impulse Response (FIR)
channel estimation driven by non-Gaussian signal. The input signal
represents the signal used in 10GBASE-T (or IEEE 802.3an-2006)
as a Tomlinson-Harashima Precoded (THP) version of random
Pulse-Amplitude Modulation with 16 discrete levels (PAM-16). The
proposed algorithms are tested using three non-minimum phase
channel for different Signal-to-Noise Ratios (SNR) and for different
data input length. Numerical simulation results are presented to
illustrate the performance of the proposed algorithms.
Abstract: System MEMORI automatically detects and recognizes rotated and/or rescaled versions of the objects of a database within digital color images with cluttered background. This task is accomplished by means of a region grouping algorithm guided by heuristic rules, whose parameters concern some geometrical properties and the recognition score of the database objects. This paper focuses on the strategies implemented in MEMORI for the estimation of the heuristic rule parameters. This estimation, being automatic, makes the system a highly user-friendly tool.
Abstract: All around the world pulp and paper industries are the
biggest plant production with the environmental pollution as the
biggest challenge facing the pulp manufacturing operations. The
concern among these industries is to produce a high volume of papers
with the high quality standard and of low cost without affecting the
environment. This result obtained from this bleaching study show
that the activation of peroxide was an effective method of reducing
the total applied charge of chlorine dioxide which is harmful to our
environment and also show that softwood and hardwood Kraft pulps
responded linearly to the peroxide treatments. During the bleaching
process the production plant produce chlorines. Under the trial stages
chloride dioxide has been reduced by 3 kg/ton to reduce the
brightness from 65% ISO to 60% ISO of pulp and the dosing point
returned to the E stage charges by pre-treating Kraft pulps with
hydrogen peroxide. The pulp and paper industry has developed
elemental chlorine free (ECF) and totally chlorine free (TCF)
bleaching, in their quest for being environmental friendly, they have
been looking at ways to turn their ECF process into a TCF process
while still being competitive. This prompted the research to
investigate the capability of the hydrogen peroxide as catalyst to
reduce chloride dioxide.
Abstract: The previous study of new metal gasket that contact
width and contact stress an important design parameter for optimizing
metal gasket performance. The optimum design based on an elastic
and plastic contact stress was founded. However, the influence of
flange surface roughness had not been investigated thoroughly. The
flange has many kinds of surface roughness. In this study, we
conducted a gasket model include a flange surface roughness effect. A
finite element method was employed to develop simulation solution. A
uniform quadratic mesh used for meshing the gasket material and a
gradually quadrilateral mesh used for meshing the flange. The gasket
model was simulated by using two simulation stages which is forming
and tightening simulation. A simulation result shows that a smoother
of surface roughness has higher slope for force per unit length. This
mean a squeezed against between flange and gasket will be strong. The
slope of force per unit length for gasket 400-MPa mode was higher
than the gasket 0-MPa mode.
Abstract: An active RC filters with a 880 / 1760 MHz dual bandwidth tuning ability is present for 60 GHz unlicensed band applications. A third order Butterworth low-pass filter utilizes two Cherry-Hooper amplifiers to satisfy the very high bandwidth requirements of an amplifier. The low-pass filter is fabricated in 90nm standard CMOS process. Drawing 6.7 mW from 1.2 V power supply, the low frequency gains of the filter are -2.5 and -4.1 dB, and the output third order intercept points (OIP3) are +2.2 and +1.9 dBm for the single channel and channel bonding conditions, respectively.
Abstract: Since 1984 many schemes have been proposed for
digital signature protocol, among them those that based on discrete
log and factorizations. However a new identification scheme based
on iterated function (IFS) systems are proposed and proved to be
more efficient. In this study the proposed identification scheme is
transformed into a digital signature scheme by using a one way hash
function. It is a generalization of the GQ signature schemes. The
attractor of the IFS is used to obtain public key from a private one,
and in the encryption and decryption of a hash function. Our aim is
to provide techniques and tools which may be useful towards
developing cryptographic protocols. Comparisons between the
proposed scheme and fractal digital signature scheme based on RSA
setting, as well as, with the conventional Guillou-Quisquater
signature, and RSA signature schemes is performed to prove that, the
proposed scheme is efficient and with high performance.
Abstract: There are three distinct stages in the evolution of
economic thought, namely:
1. in the first stage, the major concern was to accelerate
economic growth with increased availability of material
goods, especially in developing economies with very low
living standards, because poverty eradication meant faster
economic growth.
2. in the second stage, economists made distinction between
growth and development. Development was seen as going
beyond economic growth, and bringing certain changes in
the structure of the economy with more equitable
distribution of the benefits of growth, with the growth
coming automatic and sustained.
3. the third stage is now reached. Our concern is now with
“sustainable development", that is, development not only
for the present but also of the future.
Thus the focus changed from “sustained growth" to “sustained
development". Sustained development brings to the fore the long
term relationship between the ecology and economic development.
Since the creation of UNEP in 1972 it has worked for
development without destruction for environmentally sound and
sustained development. It was realised that the environment cannot
be viewed in a vaccum, it is not separate from development, nor is it
competing. It suggested for the integration of the environment with
development whereby ecological factors enter development planning,
socio-economic policies, cost-benefit analysis, trade, technology
transfer, waste management, educational and other specific areas.
Industrialisation has contributed to the growth of economy of
several countries. It has improved the standards of living of its people
and provided benefits to the society. It has also created in the process
great environmental problems like climate change, forest destruction
and denudation, soil erosion and desertification etc.
On the other hand, industry has provided jobs and improved the
prospects of wealth for the industrialists. The working class
communities had to simply put up with the high levels of pollution in
order to keep up their jobs and also to save their income.
There are many roots of the environmental problem. They may be
political, economic, cultural and technological conditions of the
modern society. The experts concede that industrial growth lies
somewhere close to the heart of the matter. Therefore, the objective
of this paper is not to document all roots of an environmental crisis
but rather to discuss the effects of industrial growth and
development.
We have come to the conclusion that although public intervention
is often unnecessary to ensure that perfectly competitive markets will
function in society-s best interests, such intervention is necessary
when firms or consumers pollute.
Abstract: The spatial variation in plant species associated with intercropping is intended to reduce resource competition between species and increase yield potential. A field experiment was carried out on corn (Zea mays L.) and soybean (Glycine max L.) intercropping in a replacement series experiment with weed contamination consist of: weed free, infestation of redroot pigweed, infestation of jimsonweed and simultaneous infestation of redroot pigweed and jimsonweed in Karaj, Iran during 2007 growing season. The experimental design was a randomized complete block in factorial experiment with replicated thrice. Significant (P≤0.05) differences were observed in yield in intercropping. Corn yield was higher in intercropping, but soybean yield was significantly reduced by corn when intercropped. However, total productivity and land use efficiency were high under the intercropping system even in contamination of either species of weeds. Aggressivity of corn relative to soybean revealed the greater competitive ability of corn than soybean. Land equivalent ratio (LER) more than 1 in all treatments attributed to intercropping advantages and was highest in 50: 50 (corn/soybean) in weed free. These findings suggest that intercropping corn and soybean increase total productivity per unit area and improve land use efficiency. Considering the experimental findings, corn-soybean intercropping (50:50) may be recommended for yield advantage, more efficient utilization of resources, and weed suppression as a biological control.
Abstract: The application of a high frequency signal injection method as speed and position observer in PMSM drives has been a research focus. At present, the precision of this method is nearly good as that of ten-bit encoder. But there are some questions for estimating position polarity. Based on high frequency signal injection, this paper presents a method to compensate position polarity for permanent magnet synchronous motor (PMSM). Experiments were performed to test the effectiveness of the proposed algorithm and results present the good performance.
Abstract: In this cyber age, the job market has been rapidly transforming and being digitalized. Submitting a paper-based curriculum vitae (CV) nowadays does not grant a job seeker a high employability rate. This paper calls for attention on the creation of mobile Curriculum Vitae or m-CV (http://mcurriculumvitae. blogspot.com), a sample of an individual CV developed using weblog, which can enhance the job hunter especially fresh graduate-s higher marketability rate. This study is designed to identify the perceptions held by Malaysian university students regarding m-CV grounded on a modified Technology Acceptance Model (TAM). It measures the strength and the direction of relationships among three major variables – Perceived Ease of Use (PEOU), Perceived Usefulness (PU) and Behavioral Intention (BI) to use. The finding shows that university students generally accepted adopting m-CV since they perceived m-CV to be more useful rather than easy to use. Additionally, this study has confirmed TAM to be a useful theoretical model in helping to understand and explain the behavioral intention to use Web 2.0 application-weblog publishing their CV. The result of the study has underlined another significant positive value of using weblog to create personal CV. Further research of m-CV has been highlighted in this paper.
Abstract: Reservoirs with high pressures and temperatures
(HPHT) that were considered to be atypical in the past are now
frequent targets for exploration. For downhole oilfield drilling tools
and components, the temperature and pressure affect the mechanical
strength. To address this issue, a finite element analysis (FEA) for
206.84 MPa (30 ksi) pressure and 165°C has been performed on the
pressure housing of the measurement-while-drilling/logging-whiledrilling
(MWD/LWD) density tool.
The density tool is a MWD/LWD sensor that measures the density
of the formation. One of the components of the density tool is the
pressure housing that is positioned in the tool. The FEA results are
compared with the experimental test performed on the pressure
housing of the density tool. Past results show a close match between
the numerical results and the experimental test. This FEA model can
be used for extreme HPHT and ultra HPHT analyses, and/or optimal
design changes.
Abstract: In today's complex global environment, emotional intelligence in educational administrations encompasses self-regard that is formed to utilize communication effectiveness. The paper is undertaken to understand the relationship between managers- emotional intelligence especially self-regard and employees to improve communication effectiveness in educational administrations of Iran. Data (N = 145) for this study were collected through questionnaires that participants were managers and employees educational administrations of Iran. The aim of this paper assess the emotional intelligence especially self-regard of managers and employees and its relationship with communication effectiveness in educational administrations of Iran. This paper explained self-regard that has a high relationship with communication especially communication effectiveness. Self-regard plays an important role in communication effectiveness. Individuals with high self-regard tend to have higher emotional intelligence and this action lead to improve communication effectiveness. The result of the paper shows a strong correspondence between self-regard and communication effectiveness in educational administrations.