Abstract: Production of biogas from bakery waste was enhanced
by additional bacterial cell. This study was divided into 2 steps. First
step, grease waste from bakery industry-s grease trap was initially
degraded by Pseudomonas aeruginosa. The concentration of byproduct,
especially glycerol, was determined and found that glycerol
concentration increased from 12.83% to 48.10%. Secondary step, 3
biodigesters were set up in 3 different substrates: non-degraded waste
as substrate in first biodigester, degraded waste as substrate in
secondary biodigester, and degraded waste mixed with swine manure
in ratio 1:1 as substrate in third biodigester. The highest
concentration of biogas was found in third biodigester that was
44.33% of methane and 63.71% of carbon dioxide. The lower
concentration at 24.90% of methane and 18.98% of carbon dioxide
was exhibited in secondary biodigester whereas the lowest was found
in non-degraded waste biodigester. It was demonstrated that the
biogas production was greatly increased with the initial grease waste
degradation by Pseudomonas aeruginosa.
Abstract: Variable digital filters are useful for various signal processing and communication applications where the frequency characteristics, such as fractional delays and cutoff frequencies, can be varied. In this paper, we propose a design method of variable FIR digital filters with an approximate linear phase characteristic in the passband. The proposed variable FIR filters have some large attenuation in stopband and their large attenuation can be varied by spectrum parameters. In the proposed design method, a quasi-equiripple characteristic can be obtained by using an iterative weighted least square method. The usefulness of the proposed design method is verified through some examples.
Abstract: Recently, Denial of Service(DoS) attacks and Distributed DoS(DDoS) attacks which are stronger form of DoS attacks from plural hosts have become security threats on the Internet. It is important to identify the attack source and to block attack traffic as one of the measures against these attacks. In general, it is difficult to identify them because information about the attack source is falsified. Therefore a method of identifying the attack source by tracing the route of the attack traffic is necessary. A traceback method which uses traffic patterns, using changes in the number of packets over time as criteria for the attack traceback has been proposed. The traceback method using the traffic patterns can trace the attack by matching the shapes of input traffic patterns and the shape of output traffic pattern observed at a network branch point such as a router. The traffic pattern is a shapes of traffic and unfalsifiable information. The proposed trace methods proposed till date cannot obtain enough tracing accuracy, because they directly use traffic patterns which are influenced by non-attack traffics. In this paper, a new traffic pattern matching method using Independent Component Analysis(ICA) is proposed.
Abstract: The usefulness of weaning foods to meet the nutrient
needs of children is well recognized, and most of them are precooked
roller dried mixtures of cereal and/or legume flours which posses a
high viscosity and bulk when reconstituted. The objective of this study
was to formulate composite weaning foods using cereals, malted
legumes and vegetable powders and analyze them for nutrients,
functional properties and sensory attributes. Selected legumes (green
gram and lentil) were germinated, dried and dehulled. Roasted wheat,
rice, carrot powder and skim milk powder also were used. All the
ingredients were mixed in different proportions to get four
formulations, made into 30% slurry and dried in roller drier. The
products were analyzed for proximate principles, mineral content,
functional and sensory qualities. The results of analysis showed
following range of constituents per 100g of formulations on dry
weight basis, protein, 18.1-18.9 g ; fat, 0.78-1.36 g ; iron, 5.09-6.53
mg; calcium, 265-310 mg. The lowest water absorption capacity was
in case of wheat green gram based and the highest was in rice lentil
based sample. Overall sensory qualities of all foods were graded as
“good" and “very good" with no significant differences. The results
confirm that formulated weaning foods were nutritionally superior,
functionally appropriate and organoleptically acceptable.
Abstract: This paper addresses a current problem that occurs among Thai internet service providers with regard to bandwidth network quality management. The IPSTAR department of Telecom Organization of Thailand public company (TOT); the largest internet service provider in Thailand, is the case study to analyze the problem that exists. The Internet bandwidth network quality management (iBWQM) framework is mainly applied to the problem that has been found. Bandwidth management policy (BMP) and quality of service (QoS) are two antecedents of iBWQM. This paper investigates internet user behavior, marketing demand and network operation views in order to determine bandwidth management policy (e.g. quota management, scheduling and malicious management). The congestion of bandwidth is also analyzed to enhance quality of service (QoS). Moreover, the iBWQM framework is able to improve the quality of service and increase bandwidth utilization, minimize complaint rate concerns to slow speed, and provide network planning guidelines through Thai Internet services providers.
Abstract: In this paper, the babbitting of a bearing in boiler feed pump of an electromotor has been studied. These bearings have an important role in reducing the shut down times in the pumps, compressors and turbines. The most conventional method in babbitting is casting as a melting method. The comparison between thermal spray and casting methods in babbitting shows that the thermal spraying babbitt layer has better performance and tribological behavior. The metallurgical and tribological analysis such as SEM, EDS and wet chemical analysis has been made in the Babbitt alloys and worn surfaces. Two type of babbitt materials: tinbase and lead-base babbitt was used. The benefits of thermally sprayed babbitt layers are completely clear especially in large bearings.
Abstract: It-s known that incorporating prior knowledge into support
vector regression (SVR) can help to improve the approximation
performance. Most of researches are concerned with the incorporation
of knowledge in form of numerical relationships. Little work,
however, has been done to incorporate the prior knowledge on the
structural relationships among the variables (referred as to Structural
Prior Knowledge, SPK). This paper explores the incorporation of SPK
in SVR by constructing appropriate admissible support vector kernel
(SV kernel) based on the properties of reproducing kernel (R.K).
Three-levels specifications of SPK are studies with the corresponding
sub-levels of prior knowledge that can be considered for the method.
These include Hierarchical SPK (HSPK), Interactional SPK (ISPK)
consisting of independence, global and local interaction, Functional
SPK (FSPK) composed of exterior-FSPK and interior-FSPK. A
convenient tool for describing the SPK, namely Description Matrix
of SPK is introduced. Subsequently, a new SVR, namely Motivated
Support Vector Regression (MSVR) whose structure is motivated
in part by SPK, is proposed. Synthetic examples show that it is
possible to incorporate a wide variety of SPK and helpful to improve
the approximation performance in complex cases. The benefits of
MSVR are finally shown on a real-life military application, Air-toground
battle simulation, which shows great potential for MSVR to
the complex military applications.
Abstract: A lightpipe is an about 99 percent specular reflective
mirror pipe or duct that is used for the transmission of the daylight
from the outside into a building. The lightpipes are usually used in
the daylighting buildings, in the residential, industrial and
commercial sectors. This paper is about the performances of a
lightpipe installed in a laboratory (3 m x 2.6 m x 3 m) without
windows. The aim is to analyse the luminous intensity distribution
for several sky/sun conditions. The lightpipe was monitored during
the year 2006. The lightpipe is 1 m long and the diameter of the top
collector and of the internal diffuser device is 0.25 m. In the
laboratory there are seven illuminance sensors: one external is
located on the roof of the laboratory and six internal sensors are
connected to a data acquisition system. The internal sensors are
positioned under the internal diffusive device at an height of 0.85 m
from the floor to simulate a working plane. The numerical data are
obtained through a simulation software. This paper shows the
comparison between the experimental and numerical results
concerning the behavior of the lightpipe.
Abstract: This research assesses the value of the brand personality and its influence on consumer-s decision making, through relational variables, after receiving a text message ad. An empirical study, in which 380 participants have received an SMS ad, confirms that brand personality does actually influence the brand trust as well as the attachment and commitment. The levels of sensitivity and involvement have an impact on the brand personality and the related variables to it.
Abstract: This paper presents unified theory for local (Savitzky-
Golay) and global polynomial smoothing. The algebraic framework
can represent any polynomial approximation and is seamless from
low degree local, to high degree global approximations. The representation
of the smoothing operator as a projection onto orthonormal
basis functions enables the computation of: the covariance matrix
for noise propagation through the filter; the noise gain and; the
frequency response of the polynomial filters. A virtually perfect Gram
polynomial basis is synthesized, whereby polynomials of degree
d = 1000 can be synthesized without significant errors. The perfect
basis ensures that the filters are strictly polynomial preserving. Given
n points and a support length ls = 2m + 1 then the smoothing
operator is strictly linear phase for the points xi, i = m+1. . . n-m.
The method is demonstrated on geometric surfaces data lying on an
invariant 2D lattice.
Abstract: Nanowire arrays of copper with uniform diameters have
been synthesized by potentiostatic electrochemical metal deposition
(EMD) of copper sulphate and potassium chloride solution within
the nano-channels of porous Indium-Tin Oxide (ITO), also known as
Tin doped Indium Oxide templates. The nanowires developed were
fairly continuous with diameters ranging from 110-140 nm along
the entire length. Single as well as poly-crystalline copper wires
have been prepared by application of appropriate potential during the
EMD process. Scanning electron microscopy (SEM), high resolution
transmission electron microscopy (HRTEM), small angle electron
diffraction (SAED) and atomic force microscopy (AFM) were used
to characterize the synthesized nano wires at room temperature. The
electrochemical response of synthesized products was evaluated by
cyclic voltammetry while surface energy analysis was carried out
using a Goniometer.
Abstract: An Advance Driver Assistance System (ADAS) is a computer system on board a vehicle which is used to reduce the risk of vehicular accidents by monitoring factors relating to the driver, vehicle and environment and taking some action when a risk is identified. Much work has been done on assessing vehicle and environmental state but there is still comparatively little published work that tackles the problem of driver state. Visual attention is one such driver state. In fact, some researchers claim that lack of attention is the main cause of accidents as factors such as fatigue, alcohol or drug use, distraction and speeding all impair the driver-s capacity to pay attention to the vehicle and road conditions [1]. This seems to imply that the main cause of accidents is inappropriate driver behaviour in cases where the driver is not giving full attention while driving. The work presented in this paper proposes an ADAS system which uses an image based template matching algorithm to detect if a driver is failing to observe particular windscreen cells. This is achieved by dividing the windscreen into 24 uniform cells (4 rows of 6 columns) and matching video images of the driver-s left eye with eye-gesture templates drawn from images of the driver looking at the centre of each windscreen cell. The main contribution of this paper is to assess the accuracy of this approach using Receiver Operating Characteristic analysis. The results of our evaluation give a sensitivity value of 84.3% and a specificity value of 85.0% for the eye-gesture template approach indicating that it may be useful for driver point of regard determinations.
Abstract: The plant world is the source of many medicines.
Recently, researchers have estimated that there are approximately
400,000 plant species worldwide, of which about a quarter or a third
have been used by societies for medicinal purposes. The human uses
of plants for thousands of years to treat various ailments, in many
developing countries, much of the population trust in traditional
doctors and their collections of medicinal plants to treat them.
Essential oils have many therapeutic properties. In herbal medicine,
they are used for their antiseptic properties against infectious
diseases of fungal origin, against dermatophytes, those of bacterial
origin. The aim of our study is to determine the antimicrobial effect
of essential oils of the plant Trigonella focnum greacum on some
pathogenic bacteria, it is a medicinal plant used in traditional
therapy. The test adopted is based on the diffusion method on solid
medium (Antibiogram), this method determines the sensitivity or
resistance of a microorganism vis-à-vis the extract studied. Our study
reveals that the essential oil of the plant Trigonella focnum greacum
has a different effect on the resistance of germs. For staphiloccocus
Pseudomonnas aeroginosa and Krebsilla, are moderately sensitive
strains, also Escherichia coli and Candida albicans represents a high
sensitivity. By against Proteus is a strain that represents a weak
sensitivity.
Abstract: Most of the biclustering/projected clustering algorithms are based either on the Euclidean distance or correlation coefficient which capture only linear relationships. However, in many applications, like gene expression data and word-document data, non linear relationships may exist between the objects. Mutual Information between two variables provides a more general criterion to investigate dependencies amongst variables. In this paper, we improve upon our previous algorithm that uses mutual information for biclustering in terms of computation time and also the type of clusters identified. The algorithm is able to find biclusters with mixed relationships and is faster than the previous one. To the best of our knowledge, none of the other existing algorithms for biclustering have used mutual information as a similarity measure. We present the experimental results on synthetic data as well as on the yeast expression data. Biclusters on the yeast data were found to be biologically and statistically significant using GO Tool Box and FuncAssociate.
Abstract: The whole-cell protein-profiling technique was
evaluated for studying differences in banding pattern of three
different species of Cyanobacteria i.e. Anabaena fertilissima,
Aulosira fertilissima and Westiellopsis prolifica under the influence
of four different pesticides-2,4-D (Ethyl Ester of 2,4-Dichloro
Phenoxy Acetic Acid), Pencycuron (N-[(4-chlorophenyl)methyl]-Ncyclopentyl-
N'–phenylurea), Endosulfan (6,7,8,9,10,10hexachloro-
1,5,5a,6,9,9a-hexahydro-6,9-methano-2,4,3-benzodioxathiepine-3-
oxide) and Tebuconazole (1-(4-Chlorophenyl)-4,4-dimethyl-3-(1,2,4-
triazol-1-ylmethyl)pentan-3-ol). Whole-cell extracts were obtained by
sonication treatment (Sonifier cell disruptor -Branson Digital Sonifier
S-450D, USA) and were analyzed by sodium dodecyl sulfate
polyacrylamide gel electrophoresis (SDS-PAGE). SDS-PAGE
analyses of the total protein profile of Anabaena fertilissima,
Aulosira fertilissima and Westiellopsis prolifica showed a linear
decrease in the protein content with increasing pesticide stress when
administered to different concentrations of 2, 4-D, Pencycuron,
Endosulfan and Tebuconazole. The results indicate that different
stressors exert specific effects on cyanobacterial protein synthesis.
Abstract: Protection of slope and embankment from erosion has
become an important issue in Bangladesh. The constructions of
strong structures require large capital, integrated designing, high
maintenance cost. Strong structure methods have negative impact on
the environment and sometimes not function for the design period.
Plantation of vetiver system along the slopes is an alternative
solution. Vetiver not only serves the purpose of slope protection but
also adds green environment reducing pollution. Vetiver is available
in almost all the districts of Bangladesh. This paper presents the
application of vetiver system with geo-jute, for slope protection and
erosion control of embankments and slopes. In-situ shear tests have
been conducted on vetiver rooted soil system to find the shear
strength. The shear strength and effective soil cohesion of vetiver
rooted soil matrix are respectively 2.0 times and 2.1 times higher than
that of the bared soil. Similar trends have been found in direct shear
tests conducted on laboratory reconstituted samples. Field trials have
been conducted in road embankment and slope protection with
vetiver at different sites. During the time of vetiver root growth the
soil protection has been accomplished by geo-jute. As the geo-jute
degrades with time, vetiver roots grow and take over the function of
geo-jutes. Slope stability analyses showed that vegetation increase
the factor of safety significantly.
Abstract: The theory of Groebner Bases, which has recently been
honored with the ACM Paris Kanellakis Theory and Practice Award,
has become a crucial building block to computer algebra, and is
widely used in science, engineering, and computer science. It is wellknown
that Groebner bases computation is EXP-SPACE in a general
polynomial ring setting.
However, for many important applications in computer science
such as satisfiability and automated verification of hardware and
software, computations are performed in a Boolean ring. In this paper,
we give an algorithm to show that Groebner bases computation is PSPACE
in Boolean rings. We also show that with this discovery,
the Groebner bases method can theoretically be as efficient as
other methods for automated verification of hardware and software.
Additionally, many useful and interesting properties of Groebner
bases including the ability to efficiently convert the bases for different
orders of variables making Groebner bases a promising method in
automated verification.
Abstract: In contrast to conventional generators, self-excited induction generators are found to be most suitable machines for wind energy conversion in remote and windy areas due to many advantages over grid connected machines. This papers presents a Self-Excited Induction Generator (SEIG) driven by wind turbine and supplying an induction motor which is coupled to a centrifugal pump. A method to describe the steady state performance based on nodal analysis is presented. Therefore the advanced knowledge of the minimum excitation capacitor value is required. The effects of variation of excitation capacitance on system and rotor speed under different loading conditions have been analyzed and considered to optimize induction motor pump performances.
Abstract: This paper presents a robust proportionalderivative
(PD) based cerebellar model articulation
controller (CMAC) for vertical take-off and landing flight
control systems. Successful on-line training and recalling
process of CMAC accompanying the PD controller is
developed. The advantage of the proposed method is mainly
the robust tracking performance against aerodynamic
parametric variation and external wind gust. The
effectiveness of the proposed algorithm is validated through
the application of a vertical takeoff and landing aircraft
control system.
Abstract: The copper flotation tailings from Konkola Copper
mine in Nchanga, Zambia were used in the study. The purpose of this
study was to determine the leaching characteristics of the tailings
material prior and after the physical beneficiation process is
employed. The Knelson gravity concentrator (KC-MD3) was used for
the beneficiation process. The copper leaching efficiencies and
impurity co-extraction percentages in both the upgraded and the raw
feed material were determined at different pH levels and temperature.
It was observed that the copper extraction increased with an increase
in temperature and a decrease in pH levels. In comparison to the raw
feed sample, the upgraded sample reported a maximum copper
extraction of 69% which was 9%, higher than raw feed % extractions.
The impurity carry over was reduced from 18% to 4 % on the
upgraded sample. The reduction in impurity co-extraction was as a
result of the removal of the reactive gangue elements during the
upgrading process, this minimized the number of side reaction
occurring during leaching.