Abstract: In this study, artificial limestone brick samples are produced by using wood sawdust wastes (WSW) having different grades of sizes and limestone powder waste (LPW). The thermo-elastic properties of produced brick samples in various WSW amounts are investigated. At 30% WSW replacement with LPW in the brick sample the thermal conductivity value is effectively reduced and the reduction in the thermal conductivity value of brick sample at 30% WSW replacement with LPW is about 38.9% as compared with control sample. The energy conservation in buildings by using LPW and WSW in masonry brick material production having low thermal conductivity reduces energy requirements. A strong relationship is also found among the thermal conductivity, unit weight and ultrasonic pulse velocity values of brick samples produced. It shows a potential to be used for walls, wooden board substitute, alternative to the concrete blocks, ceiling panels, sound barrier panels, absorption materials etc.
Abstract: Customer audits are generally used to ensure customer
that supplier is continuously able to meet his requirements while
supplying him required products and services. However, customer
audits can be considered as a very useful quality control tool for
suppliers as well. In our paper, we analyzed the process of customer
audits realized in Czech companies from both perspectives: a
supplier´s viewpoint and customer´s viewpoint. At the end, we tried
to emphasize some areas that should not be omitted during the audit
process.
Abstract: In power system protection, the need to know the load
current together with the fault level detected by a relay is important.
This is due to the fact that the relay is required to isolate the
equipment being protected if a fault is present and keep the breaker
associated with it closed if the current level is lower than the
maximum load level. This is not an issue for a radial system. This is
not the same however in a looped power system. In a looped power
system, the isolation of an equipment system will contribute to a
topology change. The change in the power system topology will then
influence or change the maximum load current and the fault level
detected by each relay. In this paper, a method of data collection for
changing topology using matlab and sim-power will be presented.
The method will take into consideration the change in topology and
collect data for each possible topology.
Abstract: Ergonomics is a useful tool for creating a healthy and
safe workplace. The long-term action of harmful conditions on the
health of workers is the emergence of occupational disease, and the
firm-s increased compensation costs associated with these diseases,
but is also the loss of time needed for educating and including new
workers in the work process. The article deals with the link of
ergonomics to occupational diseases, factors which influence these
diseases. In the conclusion, a model is described to help reduce the
risk of selected occupational diseases using ergonomic principles and
knowledge.
Abstract: An optical chemical sensing film based on
immobilizing of 1,1′- diethyl 2,2′-cyanine (pseudocyanine iodide) in
nafion film was developed for the determination of Fe(III). The
sensing film was homogeneous, transparent, and mechanically stable.
Decrease of the absorbance measured at 518 nm was observed when
the sensing film was immersed in a solution of Fe(III). The optimum
response of the sensing film to Fe(III) was obtained in a solution with
pH 4.0. Linear calibration curve over an Fe(III) concentration range
of 1-30 ppm with a limit of detection of 0.71 ppm was obtained.
Cd(II) is the major interference. The sensing film exhibited good
stability for 2 months and high reproducibility. The proposed method
was applied for the determination of Fe(III) in water samples with
satisfactory results.
Abstract: This study presents a new method for detecting the
cutting tool wear based on the measured cutting force signals using
the regression model and I-kaz method. The detection of tool wear
was done automatically using the in-house developed regression
model and 3D graphic presentation of I-kaz 3D coefficient during
machining process. The machining tests were carried out on a CNC
turning machine Colchester Master Tornado T4 in dry cutting
condition, and Kistler 9255B dynamometer was used to measure the
cutting force signals, which then stored and displayed in the DasyLab
software. The progression of the cutting tool flank wear land (VB)
was indicated by the amount of the cutting force generated. Later, the
I-kaz was used to analyze all the cutting force signals from beginning
of the cut until the rejection stage of the cutting tool. Results of the IKaz
analysis were represented by various characteristic of I-kaz 3D
coefficient and 3D graphic presentation. The I-kaz 3D coefficient
number decreases when the tool wear increases. This method can be
used for real time tool wear monitoring.
Abstract: Learning the gradient of neuron's activity function
like the weight of links causes a new specification which is
flexibility. In flexible neural networks because of supervising and
controlling the operation of neurons, all the burden of the learning is
not dedicated to the weight of links, therefore in each period of
learning of each neuron, in fact the gradient of their activity function,
cooperate in order to achieve the goal of learning thus the number of
learning will be decreased considerably.
Furthermore, learning neurons parameters immunes them against
changing in their inputs and factors which cause such changing.
Likewise initial selecting of weights, type of activity function,
selecting the initial gradient of activity function and selecting a fixed
amount which is multiplied by gradient of error to calculate the
weight changes and gradient of activity function, has a direct affect
in convergence of network for learning.
Abstract: The adsorption of bovine serum albumin (BSA), immunoglobulin G (IgG) and fibrinogen (Fgn) on fluorinated selfassembled monolayers have been studied using time of flight secondary ion mass spectrometry (ToF-SIMS) and Spectroscopic Ellipsometry (SE). The objective of the work has to establish the utility of ToF-SIMS for the determination of the amount of protein adsorbed on the surface. Quantification of surface adsorbed proteins was carried out using SE and a good correlation between ToF-SIMS results and SE was achieved. The surface distribution of proteins were also analysed using Atomic Force Microscopy (AFM). We show that the surface distribution of proteins strongly affect the ToFSIMS results.
Abstract: Papaya and banana bars were developed incorporating
inulin (IN) and fructooligosaccharides (FOS) (Liquid and Powder
form) in various proportions. The control bars were standardized
using 70% fruit pulp, 30% sugar, 0.3% citric acid while the treated
bars were standardized with 70% fruit pulp, 15% sugar, 15% of IN
and FOS and 0.3% citric acid. Among the various proportions tested,
papaya bars with 90% FOS (Powder) + 10% IN and banana bars with
90% FOS (liquid) + 10% IN were sensorially best accepted. The
study revealed that addition of IN and FOS improved the sensory
scores. The Physico-chemical and proximatecomposition analysis
revealed slight changes in brix°, total sugars, reducing sugars, nonreducing
sugars, moisture, protein, fat, vitamin C, ash, iron,
zinc, calcium and crude fibre between control and treated fruit bars.
Further the glycemic index of papaya bar was reduced from 65 to 54
when treated with FOS and IN.
Abstract: In this paper, backstepping method (BM) is proposed for a single-link flexible mechanical manipulator. In each step of this method a positive value is obtained. Selections of the gain factor values are very important because controller will have different behavior for each different set of values. Improper selection of these gains can lead to instability of the system. In order to choose proper values for gains BELBIC method has been used in this work. Finally, to prove the efficiency of this method, the obtained results of proposed model are compared with robust controller one. Results show that the combination of backstepping and BELBIC that is presented here, can stabilized the system with higher speed, shorter settling time and lower overshoot in than robust controller.
Abstract: This paper focuses on a critical component of the situational awareness (SA), the control of autonomous vertical flight for vectored thrust aerial vehicle (VTAV). With the SA strategy, we proposed a flight control procedure to address the dynamics variation and performance requirement difference of flight trajectory for an unmanned helicopter model with vectored thrust configuration. This control strategy for chosen model of VTAV has been verified by simulation of take-off and forward maneuvers using software package Simulink and demonstrated good performance for fast stabilization of motors, consequently, fast SA with economy in energy can be asserted during search-and-rescue operations.
Abstract: In this paper, the existence, multiplicity and
noexistence of positive solutions for a class of semipositone
discrete boundary value problems with two parameters is
studied by applying nonsmooth critical point theory and
sub-super solutions method.
Abstract: This paper presents a customized deformable model
for the segmentation of abdominal and thoracic aortic aneurysms in
CTA datasets. An important challenge in reliably detecting aortic
aneurysm is the need to overcome problems associated with intensity
inhomogeneities and image noise. Level sets are part of an important
class of methods that utilize partial differential equations (PDEs) and
have been extensively applied in image segmentation. A Gaussian
kernel function in the level set formulation, which extracts the local
intensity information, aids the suppression of noise in the extracted
regions of interest and then guides the motion of the evolving contour
for the detection of weak boundaries. The speed of curve evolution
has been significantly improved with a resulting decrease in
segmentation time compared with previous implementations of level
sets. The results indicate the method is more effective than other
approaches in coping with intensity inhomogeneities.
Abstract: Thermite welding is mainly used in world. The
reasons why the thermite welding method is widely used are
that the equipment has good mobility and total working time
of that is shorter than that of the enclosed arc welding method
on site. Moreover, the operating skill, which required for
thermite welding, is less than that of for enclosed arc welding.
In the present research work, heat treatment and combined
'expulsion and heat treatment' techniques were used improve
the mechanical properties and weldment structure. The
specimens were cut in the transverse direction from expulsion
with Heat treated and heat treated Thermite Welded rails.
Specimens were prepared according to AWS standard and
subjected to tensile test, Impact test and hardness and their
results were tabulated. Microstructural analysis was carried
out with the help of SEM. Then analyze to effect of heat
treated and 'expulsion with heat treated' with the properties of
their thermite welded rails. Compare the mechanical and
microstructural properties of thermite welded rails between
heat expulsion with heat treated and heat treated. Mechanical
and microstructural response expulsion with heat treated
thermite welded rail is higher value as compared to heat
treatment.
Abstract: For the improvement of the ability in detecting
small calcifications using Ultrasonography (US) we propose a
novel indicator of calcifications in an ultrasound B-mode image
without decrease in frame rate. Since the waveform of an
ultrasound pulse changes at a calcification position, the
decorrelation of adjacent scan lines occurs behind a
calcification. Therefore, we employ the decorrelation of
adjacent scan lines as an indicator of a calcification. The
proposed indicator depicted wires 0.05 mm in diameter at 2 cm
depth with a sensitivity of 86.7% and a specificity of 100%,
which were hardly detected in ultrasound B-mode images. This
study shows the potential of the proposed indicator to
approximate the detectable calcification size using an US
device to that of an X-ray imager, implying the possibility that
an US device will become a convenient, safe, and principal
clinical tool for the screening of breast cancer.
Abstract: In this paper a comprehensive algorithm is presented to alleviate the undesired simultaneous effects of target maneuvering, observed glint noise distribution, and colored noise spectrum using online colored glint noise parameter estimation. The simulation results illustrate a significant reduction in the root mean square error (RMSE) produced by the proposed algorithm compared to the algorithms that do not compensate all the above effects simultaneously.
Abstract: Different approaches for heating\cooling of stirred tanks, coils and jackets, are investigated using computational fluid dynamics (CFD).A time-dependant sliding mesh approach is applied to simulate the flow in both conditions. The investigations are carried out under the turbulent flow conditions for a Rushton impeller and heating elements are considered isothermal. The flow behavior and temperature distribution are studied for each case and heat transfer coefficient is calculated. Results show different velocity profiles for each case. Unsteady temperature distribution is not similar for different cases .In the case of the coiled stirred vessel more uniform temperature and higher heat transfer coefficient is resulted.
Abstract: This paper outlines the application of Knowledge Management (KM) principles in the context of Educational institutions. The paper caters to the needs of the engineering institutions for imparting quality education by delineating the instruction delivery process in a highly structured, controlled and quantified manner. This is done using a software tool EDULOGIC+. The central idea has been based on the engineering education pattern in Indian Universities/ Institutions. The data, contents and results produced over contiguous years build the necessary ground for managing the related accumulated knowledge. Application of KM has been explained using certain examples of data analysis and knowledge extraction.
Abstract: Digital libraries become more and more necessary in
order to support users with powerful and easy-to-use tools for
searching, browsing and retrieving media information. The starting
point for these tasks is the segmentation of video content into shots.
To segment MPEG video streams into shots, a fully automatic
procedure to detect both abrupt and gradual transitions (dissolve and
fade-groups) with minimal decoding in real time is developed in this
study. Each was explored through two phases: macro-block type's
analysis in B-frames, and on-demand intensity information analysis.
The experimental results show remarkable performance in
detecting gradual transitions of some kinds of input data and
comparable results of the rest of the examined video streams. Almost
all abrupt transitions could be detected with very few false positive
alarms.
Abstract: Thousands of masters athletes participate
quadrennially in the World Masters Games (WMG), yet this cohort
of athletes remains proportionately under-investigated. Due to a
growing global obesity pandemic in context of benefits of physical
activity across the lifespan, the prevalence of obesity in this unique
population was of particular interest. Data gathered on a sub-sample
of 535 football code athletes, aged 31-72 yrs ( =47.4, s =±7.1),
competing at the Sydney World Masters Games (2009) demonstrated
a significantly (p