Abstract: It is observed that the Weighted least-square (WLS)
technique, including the modifications, results in equiripple error
curve. The resultant error as a percent of the ideal value is highly
non-uniformly distributed over the range of frequencies for which the
differentiator is designed. The present paper proposes a modification
to the technique so that the optimization procedure results in lower
maximum relative error compared to the ideal values. Simulation
results for first order as well as higher order differentiators are given
to illustrate the excellent performance of the proposed method.
Abstract: Residue Number System (RNS) is a modular representation and is proved to be an instrumental tool in many digital signal processing (DSP) applications which require high-speed computations. RNS is an integer and non weighted number system; it can support parallel, carry-free, high-speed and low power arithmetic. A very interesting correspondence exists between the concepts of Multiple Valued Logic (MVL) and Residue Number Arithmetic. If the number of levels used to represent MVL signals is chosen to be consistent with the moduli which create the finite rings in the RNS, MVL becomes a very natural representation for the RNS. There are two concerns related to the application of this Number System: reaching the most possible speed and the largest dynamic range. There is a conflict when one wants to resolve both these problem. That is augmenting the dynamic range results in reducing the speed in the same time. For achieving the most performance a method is considere named “One-Hot Residue Number System" in this implementation the propagation is only equal to one transistor delay. The problem with this method is the huge increase in the number of transistors they are increased in order m2 . In real application this is practically impossible. In this paper combining the Multiple Valued Logic and One-Hot Residue Number System we represent a new method to resolve both of these two problems. In this paper we represent a novel design of an OHRNS-based adder circuit. This circuit is useable for Multiple Valued Logic moduli, in comparison to other RNS design; this circuit has considerably improved the number of transistors and power consumption.
Abstract: This paper will discuss about an active power generator scheduling method in order to increase the limit level of steady state systems. Some power generator optimization methods such as Langrange, PLN (Indonesian electricity company) Operation, and the proposed Z-Thevenin-based method will be studied and compared in respect of their steady state aspects. A method proposed in this paper is built upon the thevenin equivalent impedance values between each load respected to each generator. The steady state stability index obtained with the REI DIMO method. This research will review the 500kV-Jawa-Bali interconnection system. The simulation results show that the proposed method has the highest limit level of steady state stability compared to other optimization techniques such as Lagrange, and PLN operation. Thus, the proposed method can be used to create the steady state stability limit of the system especially in the peak load condition.
Abstract: The feature extraction method(s) used to recognize
hand-printed characters play an important role in ICR applications.
In order to achieve high recognition rate for a recognition system, the
choice of a feature that suits for the given script is certainly an
important task. Even if a new feature required to be designed for a
given script, it is essential to know the recognition ability of the
existing features for that script. Devanagari script is being used in
various Indian languages besides Hindi the mother tongue of majority
of Indians. This research examines a variety of feature extraction
approaches, which have been used in various ICR/OCR applications,
in context to Devanagari hand-printed script. The study is conducted
theoretically and experimentally on more that 10 feature extraction
methods. The various feature extraction methods have been evaluated
on Devanagari hand-printed database comprising more than 25000
characters belonging to 43 alphabets. The recognition ability of the
features have been evaluated using three classifiers i.e. k-NN, MLP
and SVM.
Abstract: During the last couple of years, the degree of dependence on IT systems has reached a dimension nobody imagined to be possible 10 years ago. The increased usage of mobile devices (e.g., smart phones), wireless sensor networks and embedded devices (Internet of Things) are only some examples of the dependency of modern societies on cyber space. At the same time, the complexity of IT applications, e.g., because of the increasing use of cloud computing, is rising continuously. Along with this, the threats to IT security have increased both quantitatively and qualitatively, as recent examples like STUXNET or the supposed cyber attack on Illinois water system are proofing impressively. Once isolated control systems are nowadays often publicly available - a fact that has never been intended by the developers. Threats to IT systems don’t care about areas of responsibility. Especially with regard to Cyber Warfare, IT threats are no longer limited to company or industry boundaries, administrative jurisdictions or state boundaries. One of the important countermeasures is increased cooperation among the participants especially in the field of Cyber Defence. Besides political and legal challenges, there are technical ones as well. A better, at least partially automated exchange of information is essential to (i) enable sophisticated situational awareness and to (ii) counter the attacker in a coordinated way. Therefore, this publication performs an evaluation of state of the art Intrusion Detection Message Exchange protocols in order to guarantee a secure information exchange between different entities.
Abstract: As the majority of faults are found in a few of its
modules so there is a need to investigate the modules that are
affected severely as compared to other modules and proper
maintenance need to be done in time especially for the critical
applications. As, Neural networks, which have been already applied
in software engineering applications to build reliability growth
models predict the gross change or reusability metrics. Neural
networks are non-linear sophisticated modeling techniques that are
able to model complex functions. Neural network techniques are
used when exact nature of input and outputs is not known. A key
feature is that they learn the relationship between input and output
through training. In this present work, various Neural Network Based
techniques are explored and comparative analysis is performed for
the prediction of level of need of maintenance by predicting level
severity of faults present in NASA-s public domain defect dataset.
The comparison of different algorithms is made on the basis of Mean
Absolute Error, Root Mean Square Error and Accuracy Values. It is
concluded that Generalized Regression Networks is the best
algorithm for classification of the software components into different
level of severity of impact of the faults. The algorithm can be used to
develop model that can be used for identifying modules that are
heavily affected by the faults.
Abstract: Due to the high percentage of induction motors in industrial market, there exist a large opportunity for energy savings. Replacement of working induction motors with more efficient ones can be an important resource for energy savings. A calculation of energy savings and payback periods, as a result of such a replacement, based on nameplate motor efficiency or manufacture-s data can lead to large errors [1]. Efficiency of induction motors (IMs) can be extracted using some procedures that use the no-load test results. In the cases that we must estimate the efficiency on-line, some of these procedures can-t be efficient. In some cases the efficiency estimates using the rating values of the motor, but these procedures can have errors due to the different working condition of the motor. In this paper the efficiency of an IM estimated by using the genetic algorithm. The results are compared with the measured values of the torque and power. The results show smaller errors for this procedure compared with the conventional classical procedures, hence the cost of the equipments is reduced and on-line estimation of the efficiency can be made.
Abstract: This study investigated a strategy of blending lead-laden sludge and Al-rich precursors to reduce the release of metals from the stabilized products. Using PbO as the simulated lead-laden sludge to sinter with γ-Al2O3 by Pb:Al molar ratios of 1:2 and 1:12, PbAl2O4 and PbAl12O19 were formed as final products during the sintering process, respectively. By firing the PbO + γ-Al2O3 mixtures with different Pb/Al molar ratios at 600 to 1000 °C, the lead transformation was determined through X-ray diffraction (XRD) data. In Pb/Al molar ratio of 1/2 system, the formation of PbAl2O4 is initiated at 700 °C, but an effective formation was observed above 750 °C. An intermediate phase, Pb9Al8O21, was detected in the temperature range of 800-900 °C. However, different incorporation behavior for sintering PbO with Al-rich precursors at a Pb/Al molar ratio of 1/12 was observed during the formation of PbAl12O19 in this system. In the sintering process, both temperature and time effect on the formation of PbAl2O4 and PbAl12O19 phases were estimated. Finally, a prolonged leaching test modified from the U.S. Environmental Protection Agency-s toxicity characteristic leaching procedure (TCLP) was used to evaluate the durability of PbO, Pb9Al8O21, PbAl2O4 and PbAl12O19 phases. Comparison for the leaching results of the four phases demonstrated the higher intrinsic resistance of PbAl12O19 against acid attack.
Abstract: Pattern recognition and image recognition methods are commonly developed and tested using testbeds, which contain known responses to a query set. Until now, testbeds available for image analysis and content-based image retrieval (CBIR) have been scarce and small-scale. Here we present the one million images CEA-List Image Collection (CLIC) testbed that we have produced, and report on our use of this testbed to evaluate image analysis merging techniques. This testbed will soon be made publicly available through the EU MUSCLE Network of Excellence.
Abstract: In this research, CaO-ZnO catalysts (with various
Ca:Zn atomic ratios of 1:5, 1:3, 1:1, and 3:1) prepared by incipientwetness
impregnation (IWI) and co-precipitation (CP) methods were
used as a catalyst in the transesterification of palm oil with methanol
for biodiesel production. The catalysts were characterized by several
techniques, including BET method, CO2-TPD, and Hemmett
Indicator. The effects of precursor concentration, and calcination
temperature on the catalytic performance were studied under reaction
conditions of a 15:1 methanol to oil molar ratio, 6 wt% catalyst,
reaction temperature of 60°C, and reaction time of 8 h. At Ca:Zn
atomic ratio of 1:3 gave the highest FAME value owing to a basic
properties and surface area of the prepared catalyst.
Abstract: This paper reports the results of an experimental work
conducted to investigate the effect of curing conditions on the
compressive strength of self-compacting geopolymer concrete
prepared by using fly ash as base material and combination of sodium
hydroxide and sodium silicate as alkaline activator. The experiments
were conducted by varying the curing time and curing temperature in
the range of 24-96 hours and 60-90°C respectively. The essential
workability properties of freshly prepared Self-compacting
Geopolymer concrete such as filling ability, passing ability and
segregation resistance were evaluated by using Slump flow,
V-funnel, L-box and J-ring test methods. The fundamental
requirements of high flowability and resistance to segregation as
specified by guidelines on Self-compacting Concrete by EFNARC
were satisfied. Test results indicate that longer curing time and curing
the concrete specimens at higher temperatures result in higher
compressive strength. There was increase in compressive strength
with the increase in curing time; however increase in compressive
strength after 48 hours was not significant. Concrete specimens cured
at 70°C produced the highest compressive strength as compared to
specimens cured at 60°C, 80°C and 90°C.
Abstract: This study was conducted to evaluate factors
regulating groundwater quality in an area with agriculture as main
use. Under this study twelve groundwater samples have been
collected from Padra taluka, Dabhoi taluka and Savli taluka of
Vadodara district. Groundwater samples were chemically analyzed
for major physicochemical parameter in order to understand the
different geochemical processes affecting the groundwater quality.
The analytical results shows higher concentration of total dissolved
solids (16.67%), electrical conductivity (25%) and magnesium
(8.33%) for pre monsoon and total dissolved solids (16.67%),
electrical conductivity (33.3%) and magnesium (8.33%) for post
monsoon which indicates signs of deterioration as per WHO and BIS
standards. On the other hand, 50% groundwater sample is unsuitable
for irrigation purposes based on irrigation quality parameters. The
study revealed that application of fertilizer for agricultural
contributing the higher concentration of ions in aquifer of Vadodara
district.
Abstract: In developing a text-to-speech system, it is well
known that the accuracy of information extracted from a text is
crucial to produce high quality synthesized speech. In this paper, a
new scheme for converting text into its equivalent phonetic spelling
is introduced and developed. This method is applicable to many
applications in text to speech converting systems and has many
advantages over other methods. The proposed method can also
complement the other methods with a purpose of improving their
performance. The proposed method is a probabilistic model and is
based on Smooth Ergodic Hidden Markov Model. This model can be
considered as an extension to HMM. The proposed method is applied
to Persian language and its accuracy in converting text to speech
phonetics is evaluated using simulations.
Abstract: Dual phase steels (DPS)s have a microstructure
consisting of a hard second phase called Martensite in the soft Ferrite
matrix. In recent years, there has been interest in dual-phase steels,
because the application of these materials has made significant usage;
particularly in the automotive sector Composite microstructure of
(DPS)s exhibit interesting characteristic mechanical properties such
as continuous yielding, low yield stress to tensile strength
ratios(YS/UTS), and relatively high formability; which offer
advantages compared with conventional high strength low alloy
steels(HSLAS). The research dealt with the characterization of
damage in (DPS)s. In this study by review the mechanisms of failure
due to volume fraction of martensite second phase; a new method is
introduced to identifying the mechanisms of failure in the various
phases of these types of steels. In this method the acoustic emission
(AE) technique was used to detect damage progression. These failure
mechanisms consist of Ferrite-Martensite interface decohesion and/or
martensite phase fracture. For this aim, dual phase steels with
different volume fraction of martensite second phase has provided by
various heat treatment methods on a low carbon steel (0.1% C), and
then AE monitoring is used during tensile test of these DPSs. From
AE measurements and an energy ratio curve elaborated from the
value of AE energy (it was obtained as the ratio between the strain
energy to the acoustic energy), that allows detecting important
events, corresponding to the sudden drops. These AE signals events
associated with various failure mechanisms are classified for ferrite
and (DPS)s with various amount of Vm and different martensite
morphology. It is found that AE energy increase with increasing Vm.
This increasing of AE energy is because of more contribution of
martensite fracture in the failure of samples with higher Vm. Final
results show a good relationship between the AE signals and the
mechanisms of failure.
Abstract: Road signs are the elements of roads with a lot of
influence in driver-s behavior. So that signals can fulfill its function,
they must overcome visibility and durability requirements,
particularly needed at night, when the coefficient of retroreflection
becomes a decisive factor in ensuring road safety. Accepting that the
visibility of the signage has implications for people-s safety, we
understand the importance to fulfill its function: to foster the highest
standards of service and safety in drivers. The usual conditions of
perception of any sign are determined by: age of the driver, reflective
material, luminosity, vehicle speed and emplacement. In this way,
this paper evaluates the different signals to increase the safety road.
Abstract: The main objective of this project is to build an
autonomous microcontroller-based mobile robot for a local robot
soccer competition. The black competition field is equipped with
white lines to serve as the guidance path for competing robots. Two
prototypes of soccer robot embedded with the Basic Stamp II
microcontroller have been developed. Two servo motors are used as
the drive train for the first prototype whereas the second prototype
uses two DC motors as its drive train. To sense the lines, lightdependent
resistors (LDRs) supply the analog inputs for the
microcontroller. The performances of both prototypes are evaluated.
The DC motor-driven robot has produced better trajectory control
over the one using servo motors and has brought the team into the
final round.
Abstract: The dental composites are preferably used as filling
materials due to their esthetic appearances. Nevertheless one of the
major problems, during the application of the dental composites, is
shape change named as “polymerisation shrinkage" affecting clinical
success of the dental restoration while photo-polymerisation.
Polymerisation shrinkage of composites arises basically from the
formation of a polymer due to the monomer transformation which
composes of an organic matrix phase. It was sought, throughout this
study, to detect and evaluate the structural polymerisation shrinkage
of prepared dental composites in order to optimize the effects of
various fillers included in hydroxyapatite (HA)-reinforced dental
composites and hence to find a means to modify the properties of
these dental composites prepared with defined parameters. As a
result, the shrinkage values of the experimental dental composites
were decreased by increasing the filler content of composites and the
composition of different fillers used had effect on the shrinkage of
the prepared composite systems.
Abstract: Traffic Density provides an indication of the level of
service being provided to the road users. Hence, there is a need to
study the traffic flow characteristics with specific reference to
density in detail. When the length and speed of the vehicles in a
traffic stream vary significantly, the concept of occupancy, rather
than density, is more appropriate to describe traffic concentration.
When the concept of occupancy is applied to heterogeneous traffic
condition, it is necessary to consider the area of the road space and
the area of the vehicles as the bases. Hence, a new concept named,
'area-occupancy' is proposed here. It has been found that the
estimated area-occupancy gives consistent values irrespective of
change in traffic composition.
Abstract: Aluminothermic rail welding was from the beginning
a great success because its low price even in 1895 in Germany. This
method is now, widely used all over the world for the railways
construction, maintenance and modernization. Instructions give you
guidelines for preparing papers for conferences or journals.
After 1989, the welding needs of the potentials beneficiaries
(Romanian Railways, Urban Transportation Companies) keep raise
because of the railways maintenance and modernization necessity.
The main materials that determine the Thermit (T) composition
result from manufacturing scraps all over the country. This can help
the environment by consuming these scraps.
The Romanian need for alumino-thermic welding is now by 11300
per year, and in a favourable economical environment, this amount
can reach 30000 units.
This paper tries to show the effect of two types of modifiers
introduced in the T composition on the structure and properties of an
alumino-thermic welding.
Abstract: Online news websites are one of the main and wide areas of Mass Media. Since the nineties several Jordanian newspapers were introduced to the World Wide Web to reach various and large numbers of audiances. Examples of these newspapers that have online version are Al-Rai, Ad-Dustor and AlGhad. Other pure online news websites include Ammon and Rum. The main aim of this study is to evaluate online newspaper websites using two assessment measures; usability and web content. This aim is achieved by using a questionnaire based evaluation which is based on the definition of usability and web content in the ISO document as the standard number 9241-part 11. The results are obtained based on 204 audiences- responses. The results of the research showed that the usability factor is relatively good for all Jordanian online newspapers whereas the web content factor is moderate.