Abstract: It is an established fact that polymers have several
physical limitations such as low stiffness and low resistance to
impact on loading. Hence, polymers do not usually have requisite
mechanical strength for application in various fields. The
reinforcement by high strength fibers provides the polymer
substantially enhanced mechanical properties and makes them more
suitable for a large number of diverse applications. This research
evaluates the effects of particulate Cow bone and Groundnut shell
additions on the mechanical properties and microstructure of cow
bone and groundnut shell reinforced epoxy composite in order to
assess the possibility of using it as a material for engineering
applications. Cow bone and groundnut shell particles reinforced with
epoxy (CBRPC and GSRPC) was prepared by varying the cow bone
and groundnut shell particles from 0-25 wt% with 5 wt% intervals. A
Hybrid of the Cow bone and Groundnut shell (HGSCB) reinforce
with epoxy was also prepared. The mechanical properties of the
developed composites were investigated. Optical microscopy was
used to examine the microstructure of the composites. The results
revealed that mechanical properties did not increase uniformly with
additions in filler but exhibited maximum properties at specific
percentages of filler additions. From the Microscopic evaluation, it
was discovered that homogeneity decreases with increase in % filler,
this could be due to poor interfacial bonding.
Abstract: Evapotranspiration is one of the most important
components of the hydrological cycle. Evapotranspiration (ETo) is an
important variable in water and energy balances on the earth’s
surface, and knowledge of the distribution of ET is a key factor in
hydrology, climatology, agronomy and ecology studies. Many
researchers have a valid relationship, which is a function of climate
factors, to estimate the potential evapotranspiration presented to the
plant water stress or water loss, prevent. The FAO-Penman method
(PM) had been recommended as a standard method. This method
requires many data and these data are not available in every area of
world. So, other methods should be evaluated for these conditions.
When sufficient or reliable data to solve the PM equation are not
available then Hargreaves equation can be used. The Hargreaves
equation (HG) requires only daily mean, maximum and minimum air
temperature extraterrestrial radiation .In this study, Hargreaves
method (HG) were evaluated in 12 stations in the North West region
of Iran. Results of HG and M.HG methods were compared with
results of PM method. Statistical analysis of this comparison showed
that calibration process has had significant effect on efficiency of
Hargreaves method.
Abstract: HZSM-5 zeolites modified by iron and phosphorus
were applied in catalytic cracking of butene. N2 adsorption and
NH3-TPD were employed to measure the structure and acidity of
catalysts. The results indicate that increasing phosphorus loading
decreased surface area, pore volume and strong acidity of catalysts.
The addition of phosphorus significantly decreased butene conversion
and promoted propylene selectivity. The catalytic performance of
catalyst was strongly dependent on the reaction conditions.
Appropriate reaction conditions could suppress side reactions and
enhance propylene selectivity.
Abstract: The paper is focused on monitoring of dependencies
of different composition concretes on elastic modulus values.
To obtain a summary of elastic modulus development in dependence
of concrete composition design variability was the objective
of the experiment. Essential part of this work was initiated
as a reaction to building practice when questions of elastic moduli
arose at the same time and which mostly did not obtain the required
and expected values from concrete constructions.
Abstract: Implementation of advanced technologies requires
sophisticated instruments that deal with the operation, control,
restoration and protection of rapidly growing power system network
under normal and abnormal conditions. Presently, the applications of
Phasor Measurement Unit (PMU) are widely found in real time
operation, monitoring, controlling and analysis of power system
network as it eliminates the various limitations of supervisory control
and data acquisition system (SCADA) conventionally used in power
system. The use of PMU data is very rapidly increasing its
importance for online and offline analysis. Wide area measurement
system (WAMS) is developed as new technology by use of multiple
PMUs in power system. The present paper proposes a model of
Matlab based PMU using Discrete Fourier Transform (DFT)
algorithm and evaluation of its operation under different
contingencies. In this paper, PMU based two bus system having
WAMS network is presented as a case study.
Abstract: Perception, evaluation and representation of the
environment have been the subject of many disciplines including
psychology, geography and architecture. In environmental and social
psychology literature there are several evidences which suggest that
cognitive representations about a place consisted of not only
geographic items but also social and cultural. Mental representations
of residence area or a country are influenced and determined by
social-demographics, the physical and social context. Thus, all
mental representations of a given place are also social
representations. Cognitive maps are the main and common
instruments that are used to identify spatial images and the difference
between physical and subjective environments. The aim of the
current study is investigating the mental and social representations of
Turkey in university students’ minds. Data was collected from 249
university students from different departments (i.e. psychology,
geography, history, tourism departments) of Ege University.
Participants were requested to reflect Turkey in their mind onto the
paper drawing sketch maps. According to the results, cognitive maps
showed geographic aspects of Turkey as well as the context of
symbolic, cultural and political reality of Turkey. That is to say, these
maps had many symbolic and verbal items related to critics on social
and cultural problems, ongoing ethnic and political conflicts, and
actual political agenda of Turkey. Additionally, one of main
differentiations in these representations appeared in terms of the East
and West side of the Turkey, and the representations of the East and
West was varied correspondingly participants’ cultural background,
their ethnic values, and where they have born. The results of the
study were discussed in environmental and social psychological
perspective considering cultural and social values of Turkey and
current political circumstances of the country.
Abstract: The new era of digital communication has brought up
many challenges that network operators need to overcome. The high
demand of mobile data rates require improved networks, which is a
challenge for the operators in terms of maintaining the quality of
experience (QoE) for their consumers. In live video transmission,
there is a sheer need for live surveillance of the videos in order to
maintain the quality of the network. For this purpose objective
algorithms are employed to monitor the quality of the videos that are
transmitted over a network. In order to test these objective algorithms,
subjective quality assessment of the streamed videos is required, as the
human eye is the best source of perceptual assessment. In this paper we
have conducted subjective evaluation of videos with varying spatial
and temporal impairments. These videos were impaired with frame
freezing distortions so that the impact of frame freezing on the quality
of experience could be studied. We present subjective Mean Opinion
Score (MOS) for these videos that can be used for fine tuning the
objective algorithms for video quality assessment.
Abstract: Fibre cement plates, often used in construction,
generally are made using quartz as an inert material, cement as a
binder and cellulose as a fibre. This paper, first of all, investigates the
mechanical properties and durability of fibre cement plates when
quartz is both partly and fully replaced with diatomite. Diatomite
does not only have lower density compared to quartz but also has
high pozzolanic activity. The main objective of this paper is the
investigation of the effects of supplementary cementing materials
(SCMs) on the short and long term mechanical properties and
durability characteristics of fibre cement plates prepared using
diatomite. Supplementary cementing materials such as ground
granulated blast furnace slug (GGBS) and fly ash (FA) are used in
this study. Volume proportions of 10, 20, 30 and 40% of GGBS and
FA are used as partial replacement materials to cement. Short and
long term mechanical properties such as compressive and flexural
strengths as well as sorptivity characteristics and mass were
investigated. Consistency and setting time at each replacement levels
of SCMs were also recorded. The effects of using supplementary
cementing materials on the carbonation and sulphate resistance of
fibre cement plates were then experimented. The results, first of all,
show that the use of diatomite as a full or partial replacement to
quartz resulted in a systematic decrease in total mass of the fibre
cement plates. The reduction of mass was largely due to the lower
density and finer particle size of diatomite compared to quartz. The
use of diatomite did not only reduce the mass of these plates but also
increased the compressive strength significantly as a result of its high
pozzolanic activity. The replacement levels of both GGBS and FA
resulted in a systematic decrease in short term compressive strength
with increasing replacement levels. This was essentially expected as
the total rate of hydration is much lower in GGBS and FA than that
of cement. Long term results however, indicated that the compressive
strength of fibre cement plates prepared using both GGBS and FA
increases with time and hence the compressive strength of plates
prepared using SCMs is either equivalent or more than the
compressive strength of plates prepared using cement alone.
Durability characteristics of fibre cement plates prepared using SCMs
were enhanced significantly. Measurements of sopritivty
characteristics were also indicated that the plates prepared using
SCMs has much lower water absorption capacities compared to
plates prepared cement alone. Much higher resistance to carbonation
and sulphate attach were observed with plates prepared using SCMs.
The results presented in this paper show that the use of SCMs does
not only support the production of more sustainable construction
materials but also enhances the mechanical properties and durability
characteristics of fibre cement plates.
Abstract: This paper presents a new automatic vehicle detection
method from very high resolution aerial images to measure traffic
density. The proposed method starts by extracting road regions from
image using road vector data. Then, the road image is divided into
equal sections considering resolution of the images. Gradient vectors
of the road image are computed from edge map of the corresponding
image. Gradient vectors on the each boundary of the sections are
divided where the gradient vectors significantly change their
directions. Finally, number of vehicles in each section is carried out
by calculating the standard deviation of the gradient vectors in each
group and accepting the group as vehicle that has standard deviation
above predefined threshold value. The proposed method was tested in
four very high resolution aerial images acquired from Istanbul,
Turkey which illustrate roads and vehicles with diverse
characteristics. The results show the reliability of the proposed
method in detecting vehicles by producing 86% overall F1 accuracy
value.
Abstract: The aim of this research is to clarify the difference by
industry segment or product characteristics as regards organisation
management for an open innovation to raise R&D performance. In
particular, the trait of the pharmaceutical industry is defined in
comparison with IT component industry segment. In considering open
innovation, both inter-organisational relation and the management in
an organisation are important issues. As methodology, a questionnaire
was conducted. In conclusion, suitable organisation management
according to the difference in industry segment or product
characteristics became clear.
Abstract: Continuous upflow filters can combine the nutrient
(nitrogen and phosphate) and suspended solid removal in one unit
process. The contaminant removal could be achieved chemically or
biologically; in both processes the filter removal efficiency depends
on the interaction between the packed filter media and the influent. In
this paper a residence time distribution (RTD) study was carried out
to understand and compare the transfer behaviour of contaminants
through a selected filter media packed in a laboratory-scale
continuous up flow filter; the selected filter media are limestone and
white dolomite. The experimental work was conducted by injecting a
tracer (red drain dye tracer –RDD) into the filtration system and then
measuring the tracer concentration at the outflow as a function of
time; the tracer injection was applied at hydraulic loading rates
(HLRs) (3.8 to 15.2 m h-1). The results were analysed according to
the cumulative distribution function F(t) to estimate the residence
time of the tracer molecules inside the filter media. The mean
residence time (MRT) and variance σ2 are two moments of RTD that
were calculated to compare the RTD characteristics of limestone with
white dolomite. The results showed that the exit-age distribution of
the tracer looks better at HLRs (3.8 to 7.6 m h-1) and (3.8 m h-1) for
limestone and white dolomite respectively. At these HLRs the
cumulative distribution function F(t) revealed that the residence time
of the tracer inside the limestone was longer than in the white
dolomite; whereas all the tracer took 8 minutes to leave the white
dolomite at 3.8 m h-1. On the other hand, the same amount of the
tracer took 10 minutes to leave the limestone at the same HLR. In
conclusion, the determination of the optimal level of hydraulic
loading rate, which achieved the better influent distribution over the
filtration system, helps to identify the applicability of the material as
filter media. Further work will be applied to examine the efficiency
of the limestone and white dolomite for phosphate removal by
pumping a phosphate solution into the filter at HLRs (3.8 to 7.6 m h-1).
Abstract: The sea waves carry thousands of GWs of power
globally. Although there are a number of different approaches to
harness offshore energy, they are likely to be expensive, practically
challenging, and vulnerable to storms. Therefore, this paper considers
using the near shore waves for generating mechanical and electrical
power. It introduces two new approaches, the wave manipulation and
using a variable duct turbine, for intercepting very wide wave fronts
and coping with the fluctuations of the wave height and the sea level,
respectively. The first approach effectively allows capturing much
more energy yet with a much narrower turbine rotor. The second
approach allows using a rotor with a smaller radius but captures
energy of higher wave fronts at higher sea levels yet preventing it
from totally submerging. To illustrate the effectiveness of the first
approach, the paper contains a description and the simulation results
of a scale model of a wave manipulator. Then, it includes the results
of testing a physical model of the manipulator and a single duct, axial
flow turbine in a wave flume in the laboratory. The paper also
includes comparisons of theoretical predictions, simulation results,
and wave flume tests with respect to the incident energy, loss in wave
manipulation, minimal loss, brake torque, and the angular velocity.
Abstract: A novel method is presented for obtaining the stress
field induced by an edge dislocation in a multilayered composite. To
demonstrate the applications of the obtained solution, we consider the
problem of an interfacial crack in a periodically layered bimaterial
medium. The crack is modelled as a continuous distribution of edge
dislocations and the Distributed Dislocation Technique (DDT) is
utilized to obtain numerical results for the energy release rate (ERR).
The numerical implementation of the dislocation solution in
MATLAB is also provided.
Abstract: Background in music analysis: Traditionally, when we
think about a composer’s sketches, the chances are that we are
thinking in terms of the working out of detail, rather than the
evolution of an overall concept. Since music is a “time art,” it follows
that questions of a form cannot be entirely detached from
considerations of time. One could say that composers tend to regard
time either as a place gradually and partially intuitively filled, or they
can look for a specific strategy to occupy it. It seems that the one
thing that sheds light on Stockhausen’s compositional thinking is his
frequent use of “form schemas,” that is often a single-page
representation of the entire structure of a piece.
Background in music technology: Sonic Visualiser is a program
used to study a musical recording. It is an open source application for
viewing, analyzing, and annotating music audio files. It contains a
number of visualisation tools, which are designed with useful default
parameters for musical analysis. Additionally, the Vamp plugin
format of SV supports to provide analysis such as for example
structural segmentation.
Aims: The aim of paper is to show how SV may be used to obtain
a better understanding of the specific musical work, and how the
compositional strategy does impact on musical structures and musical
surfaces. It is known that “traditional” music analytic methods don’t
allow indicating interrelationships between musical surface (which is
perceived) and underlying musical/acoustical structure.
Main Contribution: Stockhausen had dealt with the most diverse
musical problems by the most varied methods. A characteristic which
he had never ceased to be placed at the center of his thought and
works, it was the quest for a new balance founded upon an acute
connection between speculation and intuition. In the case with
Mikrophonie I (1964) for tam-tam and 6 players Stockhausen makes
a distinction between the “connection scheme,” which indicates the
ground rules underlying all versions, and the form scheme, which is
associated with a particular version. The preface to the published
score includes both the connection scheme, and a single instance of a
“form scheme,” which is what one can hear on the CD recording. In
the current study, the insight into the compositional strategy chosen
by Stockhausen was been compared with auditory image, that is, with
the perceived musical surface. Stockhausen’s musical work is
analyzed both in terms of melodic/voice and timbre evolution.
Implications: The current study shows how musical structures
have determined of musical surface. The general assumption is this,
that while listening to music we can extract basic kinds of musical
information from musical surfaces. It is shown that interactive
strategies of musical structure analysis can offer a very fruitful way
of looking directly into certain structural features of music.
Abstract: Dynamics of a rotor supported by air bearings is
strongly depends on the pressure distribution between the rotor and
the bearing. In this study, internal pressure in air bearings is
numerical and experimental analyzed for different radial clearances.
Firstly the pressure distribution between rotor and bearing is modeled
using Reynold's equation and this model is solved numerically. The
rotor-bearing system is also modeled in four degree of freedom and it
is simulated for different radial clearances. Then, in order to validate
numerical results, a test rig is designed and the rotor bearing system
is run under the same operational conditions. Pressure signals of left
and right bearings are recorded. Internal pressure variations are
compared for numerical and experimental results for different radial
clearances.
Abstract: In the field of fashion design, 3D Mannequin is a kind
of assisting tool which could rapidly realize the design concepts.
While the concept of 3D Mannequin is applied to the computer added
fashion design, it will connect with the development and the
application of design platform and system. Thus, the situation
mentioned above revealed a truth that it is very critical to develop a
module of 3D Mannequin which would correspond with the necessity
of fashion design. This research proposes a concrete plan that
developing and constructing a system of 3D Mannequin with Kinect.
In the content, ergonomic measurements of objective human features
could be attained real-time through the implement with depth camera
of Kinect, and then the mesh morphing can be implemented through
transformed the locations of the control-points on the model by
inputting those ergonomic data to get an exclusive 3D mannequin
model. In the proposed methodology, after the scanned points from the
Kinect are revised for accuracy and smoothening, a complete human
feature would be reconstructed by the ICP algorithm with the method
of image processing. Also, the objective human feature could be
recognized to analyze and get real measurements. Furthermore, the
data of ergonomic measurements could be applied to shape morphing
for the division of 3D Mannequin reconstructed by feature curves. Due
to a standardized and customer-oriented 3D Mannequin would be
generated by the implement of subdivision, the research could be
applied to the fashion design or the presentation and display of 3D
virtual clothes. In order to examine the practicality of research
structure, a system of 3D Mannequin would be constructed with JAVA
program in this study. Through the revision of experiments the
practicability-contained research result would come out.
Abstract: UAV’s are small remote operated or automated aerial
surveillance systems without a human pilot aboard. UAV’s generally
finds its use in military and special operation application, a recent
growing trend in UAV’s finds its application in several civil and nonmilitary
works such as inspection of power or pipelines. The
objective of this paper is the augmentation of a UAV in order to
replace the existing expensive sonar (Sound Navigation And
Ranging) based equipment amongst small scale fisherman, for whom
access to sonar equipment are restricted due to limited economic
resources. The surveillance equipment’s present in the UAV will
relay data and GPS (Global Positioning System) location onto a
receiver on the fishing boat using RF signals, using which the
location of the schools of fishes can be found. In addition to this, an
emergency beacon system is present for rescue operations and drone
recovery.
Abstract: This study, for its research subjects, uses patients who
had undergone total knee replacement surgery from the database of the
National Health Insurance Administration. Through the review of
literatures and the interviews with physicians, important factors are
selected after careful screening. Then using Cross Entropy Method,
Genetic Algorithm Logistic Regression, and Particle Swarm
Optimization, the weight of each factor is calculated and obtained. In
the meantime, Excel VBA and Case Based Reasoning are combined
and adopted to evaluate the system. Results show no significant
difference found through Genetic Algorithm Logistic Regression and
Particle Swarm Optimization with over 97% accuracy in both
methods. Both ROC areas are above 0.87. This study can provide
critical reference to medical personnel as clinical assessment to
effectively enhance medical care quality and efficiency, prevent
unnecessary waste, and provide practical advantages to resource
allocation to medical institutes.
Abstract: Due to today’s globalization as well as outsourcing
practices of the companies, the Supply Chain (SC) performances
have become more dependent on the efficient movement of material
among places that are geographically dispersed, where there is more
chance for disruptions. One such disruption is the quality and
delivery uncertainties of outsourcing. These uncertainties could lead
the products to be unsafe and, as is the case in a number of recent
examples, companies may have to end up in recalling their products.
As a result of these problems, there is a need to develop a
methodology for selecting suppliers globally in view of risks
associated with low quality and late delivery. Accordingly, we
developed a two-stage stochastic model that captures the risks
associated with uncertainty in quality and delivery as well as a
solution procedure for the model. The stochastic model developed
simultaneously optimizes supplier selection and purchase quantities
under price discounts over a time horizon. In particular, our target is
the study of global organizations with multiple sites and multiple
overseas suppliers, where the pricing is offered in suppliers’ local
currencies. Our proposed methodology is applied to a case study for a
US automotive company having two assembly plants and four
potential global suppliers to illustrate how the proposed model works
in practice.
Abstract: Rapid Prototyping (RP) technologies enable physical
parts to be produced from various materials without depending on the
conventional tooling. Fused Deposition Modeling (FDM) is one of
the famous RP processes used at present. Tensile strength and
compressive strength resistance will be identified for different sample
structures and different layer orientations of ABS rapid prototype
solid models. The samples will be fabricated by a FDM rapid
prototyping machine in different layer orientations with variations in
internal geometrical structure. The 0° orientation where layers were
deposited along the length of the samples displayed superior strength
and impact resistance over all the other orientations. The anisotropic
properties were probably caused by weak interlayer bonding and
interlayer porosity.