Abstract: To construct the lumped spring-mass model
considering the occupants for the offset frontal crash, the SISAME
software and the NHTSA test data were used. The data on 56 kph 40%
offset frontal vehicle to deformable barrier crash test of a MY2007
Mazda 6 4-door sedan were obtained from NHTSA test database. The
overall behaviors of B-pillar and engine of simulation models agreed
very well with the test data. The trends of accelerations at the driver
and passenger head were similar but big differences in peak values.
The differences of peak values caused the large errors of the HIC36
and 3 ms chest g’s. To predict well the behaviors of dummies, the
spring-mass model for the offset frontal crash needs to be improved.
Abstract: Designing cost-efficient, secure network protocols for
Wireless Sensor Networks (WSNs) is a challenging problem because
sensors are resource-limited wireless devices. Security services such
as authentication and improved pairwise key establishment are
critical to high efficient networks with sensor nodes. For sensor
nodes to correspond securely with each other efficiently, usage of
cryptographic techniques is necessary. In this paper, two key
predistribution schemes that enable a mobile sink to establish a
secure data-communication link, on the fly, with any sensor nodes.
The intermediate nodes along the path to the sink are able to verify
the authenticity and integrity of the incoming packets using a
predicted value of the key generated by the sender’s essential power.
The proposed schemes are based on the pairwise key with the mobile
sink, our analytical results clearly show that our schemes perform
better in terms of network resilience to node capture than existing
schemes if used in wireless sensor networks with mobile sinks.
Abstract: Under active stress conditions, a rigid cantilever
retaining wall tends to rotate about a pivot point located within the
embedded depth of the wall. For purely granular and cohesive soils, a
methodology was previously reported called minimization of moment
ratio to determine the location of the pivot point of rotation. The
usage of this new methodology is to estimate the rotational stability
safety factor. Moreover, the degree of improvement required in a
backfill to get a desired safety factor can be estimated by the concept
of the shear strength demand. In this article, the accuracy of this
method for another type of cantilever walls called Contiguous Bored
Pile (CBP) retaining wall is evaluated by using physical modeling
technique. Based on observations, the results of moment ratio
minimization method are in good agreement with the results of the
carried out physical modeling.
Abstract: This paper presents an approach for the classification of
an unstructured format description for identification of file formats.
The main contribution of this work is the employment of data mining
techniques to support file format selection with just the unstructured
text description that comprises the most important format features for
a particular organisation. Subsequently, the file format indentification
method employs file format classifier and associated configurations to
support digital preservation experts with an estimation of required file
format. Our goal is to make use of a format specification knowledge
base aggregated from a different Web sources in order to select file
format for a particular institution. Using the naive Bayes method,
the decision support system recommends to an expert, the file format
for his institution. The proposed methods facilitate the selection of
file format and the quality of a digital preservation process. The
presented approach is meant to facilitate decision making for the
preservation of digital content in libraries and archives using domain
expert knowledge and specifications of file formats. To facilitate
decision-making, the aggregated information about the file formats is
presented as a file format vocabulary that comprises most common
terms that are characteristic for all researched formats. The goal is to
suggest a particular file format based on this vocabulary for analysis
by an expert. The sample file format calculation and the calculation
results including probabilities are presented in the evaluation section.
Abstract: This research aims to develop an algorithm to
generate a schedule of multiple cranes that will maximize load
throughputs in anodizing operation. The algorithm proposed utilizes
an enumerative strategy to search for constant time between
successive loads and crane covering range over baths. The computer
program developed is able to generate a near-optimal crane schedule
within reasonable times, i.e. within 10 minutes. Its results are
compared with existing solutions from an aluminum extrusion
industry. The program can be used to generate crane schedules for
mixed products, thus allowing mixed-model line balancing to
improve overall cycle times.
Abstract: Experts, enterprises and operators expect that the
bandwidth request will increase up to rates of 100 to 1,000 Mbps
within several years. Therefore the most important question is which
technology shall satisfy the future consumer broadband demands.
Currently the consensus is, that the fiber technology has the best
technical characteristics to achieve such the high bandwidth rates.
But fiber technology is so far very cost-intensive and resource
consuming. To avoid these investments, operators are concentrating
to upgrade the existing copper and hybrid fiber coax infrastructures.
This work presents a comparison of the copper and fiber
technologies including an overview about the current German
broadband market. Both technologies are reviewed in the terms of
demand, willingness to pay and economic efficiency in connection
with the technical characteristics.
Abstract: The aim of this investigation is to elaborate nearinfrared
methods for testing and recognition of chemical components
and quality in “Pannon wheat” allied (i.e. true to variety or variety
identified) milling fractions as well as to develop spectroscopic
methods following the milling processes and evaluate the stability of
the milling technology by different types of milling products and
according to sampling times, respectively. These wheat categories
produced under industrial conditions where samples were collected
versus sampling time and maximum or minimum yields. The changes
of the main chemical components (such as starch, protein, lipid) and
physical properties of fractions (particle size) were analysed by
dispersive spectrophotometers using visible (VIS) and near-infrared
(NIR) regions of the electromagnetic radiation. Close correlation
were obtained between the data of spectroscopic measurement
techniques processed by various chemometric methods (e.g. principal
component analysis [PCA], cluster analysis [CA]) and operation
condition of milling technology. It is obvious that NIR methods are
able to detect the deviation of the yield parameters and differences of
the sampling times by a wide variety of fractions, respectively. NIR
technology can be used in the sensitive monitoring of milling
technology.
Abstract: In this work, the Ictalurus punctatus species estimated
available physical habitat is compared with the estimated physical
habitat for the same but modified river reach, with the aim of creating
a linear park, along a length of 5 500 m.
To determine the effect of ecological park construction, on
physical habitat of the Lerma river stretch of study, first, the available
habitat for the Ictalurus punctatus species was estimated through the
simulation of the physical habitat, by using surveying, hydraulics,
and habitat information gotten at the river reach in its actual situation.
Second, it was estimated the available habitat for the above species,
upon the simulation of the physical habitat through the proposed
modification for the ecological park creation. Third, it is presented a
comparison between both scenarios in terms of available habitat
estimated for Ictalurus punctatus species, concluding that in cases of
adult and spawning life stages, changes in the channel to create an
ecological park would produce a considerable loss of potentially
usable habitat (PUH), while in the case of the juvenile life stage PUH
remains virtually unchanged, and in the case of life stage fry the PUH
would increase due to the presence of velocities and depths of lesser
magnitude, due to the presence of minor flow rates and lower volume
of the wet channel.
It is expected that habitat modification for linear park construction
may produce the lack of Ictalurus punktatus species conservation at
the river reach of the study.
Abstract: Experimental economics is subject to criticism with
regards to frequently discussed the trade-off between internal and
external validity requirements, which seems to be critically flawed.
This paper evaluates incompatibility of trade-off condition and
condition of internal validity as a prerequisite for external validity. In
addition, it outlines the imprecise concept of artificiality, which is
found to be rather improving the external validity and seems to
strengthen the illusory status of external versus internal validity
tension. Internal validity is further analyzed with regards to Duhem-
Quine problem, where unpredictability argument is significantly
weakened trough application of inductivism within the illustrative
hypothetical-deductive model. Our discussion partially weakens
critical arguments related to the robustness of results in experimental
economics, if the perfectly controlled experimental environment is
secured.
Abstract: The security of cloud services is the concern of cloud
service providers. In this paper, we will mention different
classifications of cloud attacks referred by specialized organizations.
Each agency has its classification of well-defined properties. The
purpose is to present a high-level classification of current research in
cloud computing security. This classification is organized around
attack strategies and corresponding defenses.
Abstract: As technology-based service industries grow
drastically worldwide; companies are recognizing the importance of
market preoccupancy and have made an effort to capture a large
market to gain the upper hand. To this end, a focus on patents can be
used to determine the properties of a technology, as well as to capture
advantages in technical skills, in comparison with the firm’s
competitors. However, technology-based services largely depend not
only on their technological value but also their economic value, due
to the recognized worth that is passed to a plurality of users. Thus, it
is important to determine whether there are any competitors in the
target areas and what services they provide in any field. Despite this
importance, little effort has been made to systematically benchmark
competitors in order to identify business opportunities. Thus, this
study aims to not only identify each position of technology-centered
service companies in complex market dynamics, but also to discover
new business opportunities. For this, we try to consider both
technology and market environments simultaneously by utilizing
patent data as a representative proxy for technology and trademark
dates as an index for a firm’s target goods and services. Theoretically,
this is one of the earliest attempts to combine patent data and
trademark data to analyze corporate strategies. In practice, the
research results are expected to be used as a decision criterion to
diagnose the economic value that companies can obtain by entering
the market, as well as the technological value to be passed onto their
customers. Thus, the proposed approach can be useful to support
effective technology and business strategies in a firm.
Abstract: A sensory network consists of multiple detection
locations called sensor nodes, each of which is tiny, featherweight
and portable. A single path routing protocols in wireless sensor
network can lead to holes in the network, since only the nodes
present in the single path is used for the data transmission. Apart
from the advantages like reduced computation, complexity and
resource utilization, there are some drawbacks like throughput,
increased traffic load and delay in data delivery. Therefore, multipath
routing protocols are preferred for WSN. Distributing the traffic
among multiple paths increases the network lifetime. We propose a
scheme, for the data to be transmitted through a dominant path to
save energy. In order to obtain a high delivery ratio, a basic route
reconstruction protocol is utilized to reconstruct the path whenever a
failure is detected. A basic reconstruction routing (BRR) algorithm is
proposed, in which a node can leap over path failure by using the
already existing routing information from its neighbourhood while
the composed data is transmitted from the source to the sink. In order
to save the energy and attain high data delivery ratio, data is
transmitted along a multiple path, which is achieved by BRR
algorithm whenever a failure is detected. Further, the analysis of
how the proposed protocol overcomes the drawback of the existing
protocols is presented. The performance of our protocol is compared
to AOMDV and energy efficient node-disjoint multipath routing
protocol (EENDMRP). The system is implemented using NS-2.34.
The simulation results show that the proposed protocol has high
delivery ratio with low energy consumption.
Abstract: The venture capital becomes more and more advanced
and effective source of the innovation project financing, connected
with a high-risk level. In the developed countries, it plays a key role
in transforming innovation projects into successful businesses and
creating the prosperity of the modern economy. In Russia, there are
many necessary preconditions for creation of the effective venture
investment system: the network of the public institutes for innovation
financing operates; there is a significant number of the small and
medium-sized enterprises, capable to sell production with good
market potential. However, the current system does not confirm the
necessary level of efficiency in practice that can be substantially
explained by the absence of the accurate plan of action to form the
national venture model and by the lack of experience of successful
venture deals with profitable exits in Russian economy. This paper
studies the influence of various factors on the venture industry
development by the example of the IT-sector in Russia. The choice of
the sector is based on the fact, that this segment is the main driver of
the venture capital market growth in Russia, and the necessary set of
data exists. The size of investment of the second round is used as the
dependent variable. To analyse the influence of the previous round,
such determinant as the volume of the previous (first) round
investments is used. There is also used a dummy variable in
regression to examine that the participation of an investor with high
reputation and experience in the previous round can influence the size
of the next investment round. The regression analysis of short-term
interrelations between studied variables reveals prevailing influence
of the volume of the first round investments on the venture
investments volume of the second round. The most important
determinant of the value of the second-round investment is the value
of first–round investment, so it means that the most competitive on
the Russian market are the start-up teams that can attract more money
on the start, and the target market growth is not the factor of crucial
importance. This supports the point of view that VC in Russia is
driven by endogenous factors and not by exogenous ones that are
based on global market growth.
Abstract: Electrohydraulic servo system have been used in industry in a wide number of applications. Its dynamics are highly nonlinear and also have large extent of model uncertainties and external disturbances. In this paper, a robust back-stepping control (RBSC) scheme is proposed to overcome the problem of disturbances and system uncertainties effectively and to improve the tracking performance of EHS systems. In order to implement the proposed control scheme, the system uncertainties in EHS systems are considered as total leakage coefficient and effective oil volume. In addition, in order to obtain the virtual controls for stabilizing system, the update rule for the system uncertainty term is induced by the Lyapunov control function (LCF). To verify the performance and robustness of the proposed control system, computer simulation of the proposed control system using Matlab/Simulink Software is executed. From the computer simulation, it was found that the RBSC system produces the desired tracking performance and has robustness to the disturbances and system uncertainties of EHS systems.
Abstract: There is not much effective guideline on development of design parameters selection on spring back for advanced high strength steel sheet metal in U-channel process during cold forming process. This paper presents the development of predictive model for spring back in U-channel process on advanced high strength steel sheet employing Response Surface Methodology (RSM). The experimental was performed on dual phase steel sheet, DP590 in Uchannel forming process while design of experiment (DoE) approach was used to investigates the effects of four factors namely blank holder force (BHF), clearance (C) and punch travel (Tp) and rolling direction (R) were used as input parameters using two level values by applying Full Factorial design (24 ). From a statistical analysis of variant (ANOVA), result showed that blank holder force (BHF), clearance (C) and punch travel (Tp) displayed significant effect on spring back of flange angle (β2 ) and wall opening angle (β1 ), while rolling direction (R) factor is insignificant. The significant parameters are optimized in order to reduce the spring back behavior using Central Composite Design (CCD) in RSM and the optimum parameters were determined. A regression model for spring back was developed. The effect of individual parameters and their response was also evaluated. The results obtained from optimum model are in agreement with the experimental values.
Abstract: An experiment was conducted to elucidate the effects of turmeric powder supplementation on egg production performance of old laying hens (80 weeks of age). There were 40 hens of Hysex Brown strain used in the study. They were caged individually, and randomly divided into 4 treatment groups of diet containing 0 (control), 1, 2 and 4 % oven dried turmeric powder for 3 periods of 4 weeks; Egg production (% hen day) and feed intake of the 4 treatment groups at the commencement of the experiment were not significantly different. In addition to egg production performance (% and egg weight), feed and water intakes were measured daily, and cholesterol content of the whole egg was determined. The results indicated that feed intakes of the hen were significantly lowered when 4% turmeric powder supplemented, while there were no significant changes in water intakes. Egg production were significantly increased and maintained at a higher level by turmeric powder supplementation up to 4% compared with the control, while the weight of eggs were not significantly affected. The research markedly demonstrated that supplementation of turmeric powder up to 4% could improve and maintain egg production performance of the old laying hen at a higher level with a lower cholesterol content.
Abstract: To solve these problems, we investigated the management system of heating enterprise, including strategic planning based on the balanced scorecard (BSC), quality management in accordance with the standards of the Quality Management System (QMS) ISO 9001 and analysis of the system based on expert judgment using fuzzy inference. To carry out our work we used the theory of fuzzy sets, the QMS in accordance with ISO 9001, BSC, method of construction of business processes according to the notation IDEF0, theory of modeling using Matlab software simulation tools and graphical programming LabVIEW. The results of the work are as follows: We determined possibilities of improving the management of heat-supply plant-based on QMS; after the justification and adaptation of software tool it has been used to automate a series of functions for the management and reduction of resources and for the maintenance of the system up to date; an application for the analysis of the QMS based on fuzzy inference has been created with novel organization of communication software with the application enabling the analysis of relevant data of enterprise management system.
Abstract: This study addresses a concept of the Sustainable Building Environmental Model (SBEM) developed to optimize energy consumption in air conditioning and ventilation (ACV) systems without any deterioration of indoor environmental quality (IEQ). The SBEM incorporates two main components: an adaptive comfort temperature control module (ACT) and a new carbon dioxide demand control module (nDCV). These two modules take an innovative approach to maintain satisfaction of the Indoor Environmental Quality (IEQ) with optimum energy consumption; they provide a rational basis of effective control. A total of 2133 sets of measurement data of indoor air temperature (Ta), relative humidity (Rh) and carbon dioxide concentration (CO2) were conducted in some Hong Kong offices to investigate the potential of integrating the SBEM. A simulation was used to evaluate the dynamic performance of the energy and air conditioning system with the integration of the SBEM in an air-conditioned building. It allows us make a clear picture of the control strategies and performed any pre-tuned of controllers before utilized in real systems. With the integration of SBEM, it was able to save up to 12.3% in simulation of overall electricity consumption, and maintain the average carbon dioxide concentration within 1000ppm and occupant dissatisfaction in 20%.
Abstract: Based on an indoor environmental quality (IEQ) index established by previous work that indicates the overall IEQ acceptance from the prospect of an occupant in residential buildings in terms of four IEQ factors - thermal comfort, indoor air quality, visual and aural comforts, this study develops a user-friendly IEQ calculator for iOS and Android users to calculate the occupant acceptance and compare the relative performance of IEQ in apartments. “IEQ calculator” is easy to use and it preliminarily illustrates the overall indoor environmental quality on the spot. Users simply input indoor parameters such as temperature, number of people and windows are opened or closed for the mobile application to calculate the scores in four areas: the comforts of temperature, brightness, noise and indoor air quality. The calculator allows the prediction of the best IEQ scenario on a quantitative scale. Any indoor environments under the specific IEQ conditions can be benchmarked against the predicted IEQ acceptance range. This calculator can also suggest how to achieve the best IEQ acceptance among a group of residents.
Abstract: In this study, we demonstrate the production of natural gas hydrates from permeable marine sediments with simultaneous mechanisms for methane recovery and methane-air or methane-air/carbon dioxide replacement. The simultaneous melting happens until the chemical potentials become equal in both phases as natural gas hydrate depletion continues and self-regulated methane-air replacement occurs over an arbitrary point. We observed certain point between dissociation and replacement mechanisms in the natural gas hydrate reservoir, and we call this boundary as critical methane concentration. By the way, when carbon dioxide was added, the process of chemical exchange of methane by air/carbon dioxide was observed in the natural gas hydrate. The suggested process will operate well for most global natural gas hydrate reservoirs, regardless of the operating conditions or geometrical constraints.