Abstract: Natural admixtures provide concrete with enhanced
properties but their processing end up making them very expensive
resulting in increase to cost of concrete. In this study the effect
of Gum from Acacia Karroo (GAK) as set-retarding admixture
in cement pastes was studied. The possibility of using GAK as
water reducing admixture both in cement mortar concrete was
also investigated. Cement pastes with different dosages of GAK
were prepared to measure the setting time using different dosages.
Compressive strength of cement mortars with 0.7, 0.8 and 0.9%
weight of cement and w/c ratio of 0.5 were compared to those with
water cement (w/c) ratio of 0.44 but same dosage of GAK. Concrete
samples were prepared using higher dosages of GAK (1, 2 and 3%
wt of cement) and a water bidder (w/b) of 0.61 were compared to
those with the same GAK dosage but with reduced w/b ratio. There
was increase in compressive strength of 9.3% at 28 days for cement
mortar samples with 0.9% dosage of GAK and reduced w/c ratio.
Abstract: This article presents an alternative collapse capacity
intensity measure in the three elements form which is influenced by
the spectral ordinates at periods longer than that of the first mode
period at near and far source sites. A parameter, denoted by β, is
defined by which the spectral ordinate effects, up to the effective
period (2T1), on the intensity measure are taken into account. The
methodology permits to meet the hazard-levelled target extreme
event in the probabilistic and deterministic forms. A MATLAB code
is developed involving OpenSees to calculate the collapse capacities
of the 8 archetype RC structures having 2 to 20 stories for regression
process. The incremental dynamic analysis (IDA) method is used to
calculate the structure’s collapse values accounting for the element
stiffness and strength deterioration. The general near field set
presented by FEMA is used in a series of performing nonlinear
analyses. 8 linear relationships are developed for the 8structutres
leading to the correlation coefficient up to 0.93. A collapse capacity
near field prediction equation is developed taking into account the
results of regression processes obtained from the 8 structures. The
proposed prediction equation is validated against a set of actual near
field records leading to a good agreement. Implementation of the
proposed equation to the four archetype RC structures demonstrated
different collapse capacities at near field site compared to those of
FEMA. The reasons of differences are believed to be due to
accounting for the spectral shape effects.
Abstract: Nonlinear evolution of broadband ultrasonic pulses
passed through the rock specimens is studied using the apparatus
“GEOSCAN-02M”. Ultrasonic pulses are excited by the pulses of Qswitched
Nd:YAG laser with the time duration of 10 ns and with the
energy of 260 mJ. This energy can be reduced to 20 mJ by some light
filters. The laser beam radius did not exceed 5 mm. As a result of the
absorption of the laser pulse in the special material – the optoacoustic
generator–the pulses of longitudinal ultrasonic waves are excited with
the time duration of 100 ns and with the maximum pressure
amplitude of 10 MPa. The immersion technique is used to measure
the parameters of these ultrasonic pulses passed through a specimen,
the immersion liquid is distilled water. The reference pulse passed
through the cell with water has the compression and the rarefaction
phases. The amplitude of the rarefaction phase is five times lower
than that of the compression phase. The spectral range of the
reference pulse reaches 10 MHz. The cubic-shaped specimens of the
Karelian gabbro are studied with the rib length 3 cm. The ultimate
strength of the specimens by the uniaxial compression is (300±10)
MPa. As the reference pulse passes through the area of the specimen
without cracks the compression phase decreases and the rarefaction
one increases due to diffraction and scattering of ultrasound, so the
ratio of these phases becomes 2.3:1. After preloading some horizontal
cracks appear in the specimens. Their location is found by one-sided
scanning of the specimen using the backward mode detection of the
ultrasonic pulses reflected from the structure defects. Using the
computer processing of these signals the images are obtained of the
cross-sections of the specimens with cracks. By the increase of the
reference pulse amplitude from 0.1 MPa to 5 MPa the nonlinear
transformation of the ultrasonic pulse passed through the specimen
with horizontal cracks results in the decrease by 2.5 times of the
amplitude of the rarefaction phase and in the increase of its duration
by 2.1 times. By the increase of the reference pulse amplitude from 5
MPa to 10 MPa the time splitting of the phases is observed for the
bipolar pulse passed through the specimen. The compression and
rarefaction phases propagate with different velocities. These features
of the powerful broadband ultrasonic pulses passed through the rock
specimens can be described by the hysteresis model of Preisach-
Mayergoyz and can be used for the location of cracks in the optically
opaque materials.
Abstract: The work reported through this paper is an
experimental work conducted on High Performance Concrete (HPC)
with super plasticizer with the aim to develop some models suitable
for prediction of compressive strength of HPC mixes. In this study,
the effect of varying proportions of fly ash (0% to 50% @ 10%
increment) on compressive strength of high performance concrete has
been evaluated. The mix designs studied were M30, M40 and M50 to
compare the effect of fly ash addition on the properties of these
concrete mixes. In all eighteen concrete mixes that have been
designed, three were conventional concretes for three grades under
discussion and fifteen were HPC with fly ash with varying
percentages of fly ash. The concrete mix designing has been done in
accordance with Indian standard recommended guidelines. All the
concrete mixes have been studied in terms of compressive strength at
7 days, 28 days, 90 days, and 365 days. All the materials used have
been kept same throughout the study to get a perfect comparison of
values of results. The models for compressive strength prediction
have been developed using Linear Regression method (LR), Artificial
Neural Network (ANN) and Leave-One-Out Validation (LOOV)
methods.
Abstract: This paper reports the viability of developing Zn-27Al
alloy matrix hybrid composites reinforced with alumina, graphite and
fly ash (solid waste bye product of coal in thermal power plants).
This research work was aimed at developing low cost-high
performance Zn-27Al matrix composite with low density. Alumina
particulates (Al2O3), graphite added with 0, 2, 3, 4 and 5 wt% fly ash
were utilized to prepare 10wt% reinforcing phase with Zn-27Al alloy
as matrix using two-step stir casting method. Density measurement,
estimated percentage porosity, tensile testing, micro hardness
measurement and optical microscopy were used to assess the
performance of the composites produced. The results show that the
hardness, ultimate tensile strength, and percent elongation of the
hybrid composites decrease with increase in fly ash content. The
maximum decrease in hardness and ultimate tensile strength of
13.72% and 15.25% respectively were observed for composite grade
containing 5wt% fly ash. The percentage elongation of composite
sample without fly ash is 8.9% which is comparable with that of the
sample containing 2wt% fly ash with percentage elongation of 8.8%.
The fracture toughness of the fly ash containing composites was
however superior to those of composites without fly ash with 5wt%
fly ash containing composite exhibiting the highest fracture
toughness. The results show that fly ash can be utilized as
complementary reinforcement in ZA-27 alloy matrix composite to
reduce cost.
Abstract: Natural fibers are used in polymer composites to
improve mechanical properties to replace inorganic reinforcing
agents produced by non-renewable resources. The present study
investigates the tensile and flexural behaviors of palm fibers-high
density polyethylene (HDPE) composite as a function of volume
fraction. The surface of the fibers was treated by mercerization
treatments to improve the wetting behavior of the apolar HDPE. The
treatment characterization was obtained by scanning electron
microscopy, X-Ray diffraction and infrared spectroscopy. Results
evidences that a good adhesion interfacial between fibers-matrix
caused an increase strength and modulus flexural as well as tensile
strength in the modified fibers/HDPE composites when compared to
the pure HDPE and untreated fibers reinforced composites.
Abstract: Analyzing the relation networks between the hospital
buildings which have complex structure and distinctive spatial
relationships is quite difficult. The hospital buildings which require
specialty in spatial relationship solutions during design and selfinnovation
through the developing technology should survive and
keep giving service even after the disasters such as earthquakes. In
this study, a hospital building where the load-bearing system was
strengthened because of the insufficient earthquake performance and
the construction of an additional building was required to meet the
increasing need for space was discussed and a comparative spatial
evaluation of the hospital building was made with regard to its status
before the change and after the change. For this reason, spatial
organizations of the building before change and after the change were
analyzed by means of Space Syntax method and the effects of the
change on space organization parameters were searched by applying
an analytical procedure. Using Depthmap UCL software,
Connectivity, Visual Mean Depth, Beta and Visual Integration
analyses were conducted. Based on the data obtained after the
analyses, it was seen that the relationships between spaces of the
building increased after the change and the building has become more
explicit and understandable for the occupants. Furthermore, it was
determined according to findings of the analysis that the increase in
depth causes difficulty in perceiving the spaces and the changes
considering this problem generally ease spatial use.
Abstract: This article deals with special structuralism
approaches to explain a certain kind of social problem. Widespread
presence of poverty is a reminder of deep-rooted unresolved
problems of social relations. The expected role from an individual for
the social system recognizes poverty derived from an interrelated
social structure. By the time, enabled to act on his role in the course
of social interaction, reintegration of the poor in society may take
place. Poverty and housing type are reflections of the underlying
social structure, primarily structure’s elements, systemic
interrelations, and the overall strength or weakness of that structure.
Poverty varies based on social structure in that the stronger structures
are less likely to produce poverty.
Abstract: Calcium Phosphate Cement (CPC) due to its high bioactivity and optimum bioresorbability shows excellent bone regeneration capability. Despite it has limited applications as bone implant due to its macro-porous microstructure causing its poor mechanical strength. The reinforcement of apatitic CPCs with biocompatible fibre glass phase is an attractive area of research to improve upon its mechanical strength. Here, we study the setting behaviour of Si-doped and un-doped α tri calcium phosphate (α - TCP) based CPC and its reinforcement with addition of E-glass fibre. Alpha Tri calcium phosphate powders were prepared by solid state sintering of CaCO3 , CaHPO4 and Tetra Ethyl Ortho Silicate (TEOS) was used as silicon source to synthesize Si doped α-TCP powders. Both initial and final setting time of the developed cement was delayed because of Si addition. Crystalline phases of HA (JCPDS 9- 432), α-TCP (JCPDS 29-359) and β-TCP (JCPDS 9-169) were detected in the X-ray diffraction (XRD) pattern after immersion of CPC in simulated body fluid (SBF) for 0 hours to 10 days. As Si incorporation in the crystal lattice stabilized the TCP phase, Si doped CPC showed little slower rate of conversion into HA phase as compared to un-doped CPC. The SEM image of the microstructure of hardened CPC showed lower grain size of HA in un-doped CPC because of premature setting and faster hydrolysis of un-doped CPC in SBF as compared that in Si-doped CPC. Premature setting caused generation of micro and macro porosity in un-doped CPC structure which resulted in its lower mechanical strength as compared to that in Si-doped CPC. It was found that addition of 10 wt% of E-glass fibre into Si-doped α-TCP increased the average DTS of CPC from 8 MPa to 15 MPa as the fibres could resists the propagation of crack by deflecting the crack tip. Our study shows that biocompatible E-glass fibre in optimum proportion in CPC matrix can enhance the mechanical strength of CPC without affecting its biocompatibility.
Abstract: Effect of alloying on the microstructure and mechanical properties of heat-resisting duplex stainless steel (DSS) for Mg production was investigated in this study. 25Cr-8Ni based DSS’s were cast into rectangular ingots of which the dimension was 350×350×100 mm3 . Nitrogen and Yttrium were added in the range within 0.3 in weight percent. Phase equilibrium was calculated using the FactSage®, thermodynamic software. Hot exposure, high temperature tensile and compression tests were conducted on the ingots at 1230oC, which is operation temperature employed for Mg production by Silico-thermic reduction. The steel with N and Y showed much higher strength than 310S alloy in both tensile and compression tests. By thermal exposition at 1230oC for 200 hrs, hardness of DSS containing N and Y was found to increase. Hot workability of the heat-resisting DSS was evaluated by employing hot rolling at 1230 oC. Hot shortness was observed in the ingot with N and found to disappear after addition of Y.
Abstract: The seriously damaged structures during earthquakes
show the need and importance of design of reinforced concrete
structures with high ductility. Reinforced concrete beam-column
joints have an important function in all structures. Under seismic
excitation, the beam column joint region is subjected to horizontal
and vertical shear forces whose magnitude is many times higher than
the adjacent beam and column. Strength and ductility of structures
depends mainly on proper detailing of the reinforcement in beamcolumn
joints and the old structures were found ductility deficient.
DSP materials are obtained by using high quantities of super
plasticizers and high volumes of micro silica. In the case of High
Performance Densified Small Particle Concrete (HPDSPC), since
concrete is dense even at the micro-structure level, tensile strain
would be much higher than that of the conventional SFRC, SIFCON
& SIMCON. This in turn will improve cracking behaviour, ductility
and energy absorption capacity of composites in addition to
durability. The fine fibers used in our mix are 0.3mm diameter and 10
mm which can be easily placed with high percentage. These fibers
easily transfer stresses and act as a composite concrete unit to take up
extremely high loads with high compressive strength. HPDSPC
placed in the beam column joints helps in safety of human life due to
prolonged failure.
Abstract: The purpose of this research was to investigate the
creep behaviour of the heterogeneous Timber-UHPFRC beams. New
developments have been done to further improve the structural
performance, such as strengthening of the timber (glulam) beam by
bonding composite material combine with an ultra-high performance
fibre reinforced concrete (UHPFRC) internally reinforced with or
without carbon fibre reinforced polymer (CFRP) bars. However, in
the design of wooden structures, in addition to the criteria of
strengthening and stiffness, deformability due to the creep of wood,
especially in horizontal elements, is also a design criterion. Glulam,
UHPFRC and CFRP may be an interesting composite mix to respond
to the issue of creep behaviour of composite structures made of
different materials with different rheological properties. In this paper,
we describe an experimental and analytical investigation of the creep
performance of the glulam-UHPFRC-CFRP beams assembled by
bonding. The experimental investigations creep behaviour was
conducted for different environments: in- and outside under constant
loading for approximately a year. The measured results are compared
with numerical ones obtained by an analytical model. This model was
developed to predict the creep response of the glulam-UHPFRCCFRP
beams based on the creep characteristics of the individual
components. The results show that heterogeneous glulam-UHPFRC
beams provide an improvement in both the strengthening and
stiffness, and can also effectively reduce the creep deflection of
wooden beams.
Abstract: MHD chemically reacting viscous fluid flow towards
a vertical surface with slip and convective boundary conditions has
been conducted. The temperature and the chemical species
concentration of the surface and the velocity of the external flow are
assumed to vary linearly with the distance from the vertical surface.
The governing differential equations are modeled and transformed
into systems of ordinary differential equations, which are then solved
numerically by a shooting method. The effects of various parameters
on the heat and mass transfer characteristics are discussed. Graphical
results are presented for the velocity, temperature, and concentration
profiles whilst the skin-friction coefficient and the rate of heat and
mass transfers near the surface are presented in tables and discussed.
The results revealed that increasing the strength of the magnetic field
increases the skin-friction coefficient and the rate of heat and mass
transfers toward the surface. The velocity profiles are increased
towards the surface due to the presence of the Lorenz force, which
attracts the fluid particles near the surface. The rate of chemical
reaction is seen to decrease the concentration boundary layer near the
surface due to the destructive chemical reaction occurring near the
surface.
Abstract: The moisture content of densified biomass is a
limiting parameter influencing the quality of this solid biofuel. It
influences its calorific value, density, mechanical strength and
dimensional stability as well as affecting its production process. This
paper deals with experimental research into the effect of moisture
content of the densified material on the final quality of biofuel in the
form of logs (briquettes or pellets). Experiments based on the singleaxis
densification of the spruce sawdust were carried out with a
hydraulic piston press (piston and die), where the densified logs were
produced at room temperature. The effect of moisture content on the
qualitative properties of the logs, including density, change of
moisture, expansion and physical changes, and compressive and
impact resistance were studied. The results show the moisture ranges
required for producing good-quality logs. The experiments were
evaluated and the moisture content of the tested material was
optimized to achieve the optimum value for the best quality of the
solid biofuel. The dense logs also have high-energy content per unit
volume. The research results could be used to develop and optimize
industrial technologies and machinery for biomass densification to
achieve high quality solid biofuel.
Abstract: A sliding door system is used in commercial vehicles
and passenger cars to allow a larger unobstructed access to the
interior for loading and unloading. The movement of a sliding door
on vehicle body is ensured by mechanisms and tracks having special
cross-section which is manufactured by roll forming and stretch
bending process. There are three tracks and three mechanisms which
are called upper, central and lower on a sliding door system. There
are static requirements as strength on different directions, rigidity for
mechanisms, door drop off, door sag; dynamic requirements as high
energy slam opening-closing and durability requirement to validate
these products. In addition, there is a kinematic requirement to find
out force values from door handle during manual operating. In this
study, finite element analysis and physical test results which are
realized for sliding door systems will be shared comparatively.
Abstract: In this study, failure analysis of pipe system at a micro
hydroelectric power plant is investigated. Failure occurred at the pipe
system in the powerhouse during shut down operation of the water
flow by a valve. This locking had caused a sudden shock wave, also
called “Water-hammer effect”, resulting in noise and inside pressure
increase. After visual investigation of the effect of the shock wave on
the system, a circumference crack was observed at the pipe flange
weld region. To establish the reason for crack formation, calculations
of pressure and stress values at pipe, flange and welding seams were
carried out and concluded that safety factor was high (2.2), indicating
that no faulty design existed. By further analysis, pipe system and
hydroelectric power plant was examined. After observations it is
determined that the plant did not include a ventilation nozzle (air
trap), that prevents the system of sudden pressure increase inside the
pipes which is caused by water-hammer effect. Analyses were carried
out to identify the influence of water-hammer effect on inside
pressure increase and it was concluded that, according Jowkowsky’s
equation, shut down time is effective on inside pressure increase. The
valve closing time was uncertain but by a shut down time of even one
minute, inside pressure would increase by 7.6 bar (working pressure
was 34.6 bar). Detailed investigations were also carried out on the
assembly of the pipe-flange system by considering technical
drawings. It was concluded that the pipe-flange system was not
installed according to the instructions. Two of five weld seams were
not applied and one weld was carried out faulty. This incorrect and
inadequate weld seams resulted in; insufficient connection of the pipe
to the flange constituting a strong notch effect at weld seam regions,
increase in stress values and the decrease of strength and safety
factor.
Abstract: When high strength reinforced concrete is exposed to
high temperature due to a fire, deteriorations occur such as loss in
strength and elastic modulus, cracking and spalling of the concrete.
Therefore, it is important to understand risk of structural safety in
building structures by studying structural behaviors and rehabilitation
of fire damaged high strength concrete structures. This paper aims at
investigating rehabilitation effect on fire damaged high strength
concrete beams using experimental and analytical methods. In the
experiments, flexural specimens with high strength concrete are
exposed to high temperatures according to ISO 834 standard time
temperature curve. From four-point loading test, results show that
maximum loads of the rehabilitated beams are similar to or higher than
those of the non-fire damaged RC beam. In addition, structural
analyses are performed using ABAQUS 6.10-3 with same conditions
as experiments to provide accurate predictions on structural and
mechanical behaviors of rehabilitated RC beams. The parameters are
the fire cover thickness and strengths of repairing mortar. Analytical
results show good rehabilitation effects, when the results predicted
from the rehabilitated models are compared to structural behaviors of
the non-damaged RC beams. In this study, fire damaged high strength concrete beams are
rehabilitated using polymeric cement mortar. The predictions from the
finite element (FE) models show good agreements with the
experimental results and the modeling approaches can be used to
investigate applicability of various rehabilitation methods for further
study.
Abstract: This study presents a hybrid metaheuristic algorithm
to obtain optimum designs for steel space buildings. The optimum
design problem of three-dimensional steel frames is mathematically
formulated according to provisions of LRFD-AISC (Load and
Resistance factor design of American Institute of Steel Construction).
Design constraints such as the strength requirements of structural
members, the displacement limitations, the inter-story drift and the
other structural constraints are derived from LRFD-AISC
specification. In this study, a hybrid algorithm by using teachinglearning
based optimization (TLBO) and harmony search (HS)
algorithms is employed to solve the stated optimum design problem.
These algorithms are two of the recent additions to metaheuristic
techniques of numerical optimization and have been an efficient tool
for solving discrete programming problems. Using these two
algorithms in collaboration creates a more powerful tool and
mitigates each other’s weaknesses. To demonstrate the powerful
performance of presented hybrid algorithm, the optimum design of a
large scale steel building is presented and the results are compared to
the previously obtained results available in the literature.
Abstract: Although there has been a growing interest in the
hybrid free-space optical link and radio frequency FSO/RF
communication system, the current literature is limited to results
obtained in moderate or cold environment. In this paper, using a soft
switching approach, we investigate the effect of weather
inhomogeneities on the strength of turbulence hence the channel
refractive index under Qatar harsh environment and their influence
on the hybrid FSO/RF availability. In this approach, either FSO/RF
or simultaneous or none of them can be active. Based on soft
switching approach and a finite state Markov Chain (FSMC) process,
we model the channel fading for the two links and derive a
mathematical expression for the outage probability of the hybrid
system. Then, we evaluate the behavior of the hybrid FSO/RF under
hazy and harsh weather. Results show that the FSO/RF soft switching
renders the system outage probability less than that of each link
individually. A soft switching algorithm is being implemented on
FPGAs using Raptor code interfaced to the two terminals of a
1Gbps/100 Mbps FSO/RF hybrid system, the first being implemented
in the region. Experimental results are compared to the above
simulation results.
Abstract: The properties of hollow sandcrete blocks produced in
Minna, Nigeria are presented. Sandcrete block is made of cement,
water and sand binded together in certain mix proportions. For the
purpose of this work, fifty (50) commercial sandcrete block industries
were visited in Minna, Nigeria to obtain block samples and
aggregates used for the manufacture, and to take inventory of the mix
composition and the production process. Sieve analysis tests were
conduction on the soil sample from various block industries to
ascertain their quality to be used for block making. The mix ratios
were also investigated. Five (5) nine inches (9’’ or 225mm) blocks
were obtained from each block industry and tested for dimensional
compliance and compressive strength. The results of the soil test
shows that the grading fall within the limit for natural aggregate and
can easily are used to obtain workable mix. Physical examinations of
the block sizes show slight deviation from the standard requirement
in NIS 87:2000. Compressive strength of hollow sandcrete blocks in
range of 0.12 N/mm2 to 0.54 N/mm2 was obtained which is below the
recommendable value of 3.45 N/mm2 for load bearing hollow
sandcrete blocks. This indicates that these blocks are below the
standard for load-bearing sandcrete blocks and cannot be used as load
bearing walling units. The mix composition also indicated low
cement content resulting in low compressive strength. Most of the
commercial block industries visited does not take curing very serious.
Water were only sprinkled ones or twice before the blocks were
stacked and made readily available for sale. It is recommended that a
mix ratio of 1:4 to 1:6 should be used for the production of sandcrete
blocks and proper curing practice should be adhered. Blocks should
also be cured for 14 days before making them available for
consumers.