Abstract: Water is essential for life and fresh water is a finite
resource that is becoming scarce day by day even though it is
recycled by hydrological cycle. The fresh water reserves are being
polluted due to expanding irrigation, industries, urban population and
its development. Contaminated water leads to several health
problems. With the increasing demand of fresh water, solar
distillation is an alternate solution which uses solar energy to
evaporate water and then to condense it, thereby collecting distilled
water within or outside the same system to use it as potable water.
The structure that houses the process is known as a 'solar still'. In this
paper, ‘Modified double slope solar still (MDSSS)’ & 'Modified
double slope basin type multiwick solar still (MDSBMSS)' have been
designed to convert saline, brackish water into drinking water. In this
work two different modified solar stills are fabricated to study the
performance of these solar stills. For modification of solar stills,
Fibre Reinforced Plastic (FRP) and Acrylic sheets are used. The
experiments in MDSBMSS and MDSSS was carried on 10
September 2015 & 5 November 2015 respectively. Performances of
the stills were investigated. The amount of distillate has been found
3624 Ml/day in MDSBMSS on 10 September 2015 and 2400 Ml/day
in MDSSS on 5 November 2015.
Abstract: In this paper, we analyze NEtwork MObility (NEMO) supporting problems in Content-Centric Networking (CCN), and propose the CCN-NEMO which can well support the deployment of the content-centric paradigm in large-scale mobile Internet. The CCN-NEMO extends the signaling message of the basic CCN protocol, to support the mobility discovery and fast trigger of Interest re-issuing during the network mobility. Besides, the Mobile Router (MR) is extended to optimize the content searching and relaying in the local subnet. These features can be employed by the nested NEMO to maximize the advantages of content retrieving with CCN. Based on the analysis, we compare the performance on handover latency between the basic CCN and our proposed CCN-NEMO. The results show that our scheme can facilitate the content-retrieving in the NEMO scenario with improved performance.
Abstract: Recently, the world main problem is a global warming and climate change affecting both outdoor and indoor environments, especially the air quality (AQ) as a result of vast migration of people from rural areas to urban areas. Therefore, cities became more crowded and denser from an irregular population increase, along with increasing urbanization caused many problems for the environment such as increasing the land prices, changes in life style, and the new buildings are not adapted to the climate producing uncomfortable and unhealthy indoor building conditions. As interior environments are the places that create the most intimate relationship with the user. Consequently, the indoor environment quality (IEQ) for buildings became uncomfortable and unhealthy for its occupants. The symptoms commonly associated with poor indoor environment such as itchy, headache, fatigue, and respiratory complaints such as cough and congestion, etc. The symptoms tend to improve over time or even disappear when people are away from the building. Therefore, designing a healthy indoor environment to fulfill human needs is the main concern for architects and interior designer. However, this research explores how occupant expectations and environmental attitudes may influence occupant health and satisfaction within the context of the indoor environment. In doing so, it reviews and contributes to the methods and tools used to evaluate only the indoor environment quality (IEQ) components of building performance. Its main aim is to review the literature on indoor human comfort. This is followed by a review of previous papers published related to human comfort. Finally, this paper will provide possible approaches in design level of healthy buildings.
Abstract: In subjective terms, Polish SME sector occupies a
prominent position in the national economic development, in which
planning of the management strategies should be primarily based on
identifying and meeting the innovation needs. As a research sample, there is chosen a printing sector of industry.
SMEs share in printing sector in Poland is estimated at the level of
81% of all enterprises. In recent years, the printing industry achieved
one of the highest levels of EU support in Poland. There is a
relatively high increase in the development of technological
innovations in equipment and the associated significant increase in
production capacity. It can be also noticed that on average, every
third enterprise belonging to the printing industry has implemented
innovations, but not all of them effected in better economic results.
Therefore, the aim of this article is to evaluate the impact of the
implementation of innovation projects financed from the EU funds
for performance of SMEs in the printing industry. As the results of research of EU funds co-financing effects on the
development of innovation in the printing industry, it was specified
that examined SMEs prefer to implement product innovation to
receive a grant to the project at a level between 40% to 60%, the
remaining part of the investment is usually covered with equity. The most common type of innovation had indicated a single
implementation, related only to the change in process, technology, or
organization. The relationship between variables of the EU funds and
management of innovative activities was verified. It has been
observed that the identified variables arising from the support in a
form of the EU funds had a positive effect on the level of earned
revenue, the increase in margin and in increase in employment as
well. It was confirmed that the implemented innovations supported
by the European funds have a positive impact on the performance of
the printing companies. Although there is a risk that due to the
decreasing demand for printing services such a high level of funding
the companies in this sector will significantly increase competition in
the long term, that may also contribute to the economic problems of
the enterprises belonging to the analyzed branch.
Abstract: The objective of this research is to mitigate and prevent
the alkali silica reactivity (ASR) in highway construction projects.
ASR is a deleterious reaction initiated when the silica content of the
aggregate reacts with alkali hydroxides in cement in the presence of
relatively high moisture content. The ASR results in the formation of
an expansive white colored gel-like material which forms the
destructive tensile stresses inside hardened concrete. In this research, different types of local aggregates available in the
State of Arkansas were mixed and mortar bars were poured according
to the ASTM specifications. Mortar bars expansion was measured
versus time and aggregates with potential ASR problems were
detected. Different types of supplementary cementitious materials
(SCMs) were used in remixing mortar bars with highly reactive
aggregates. Length changes for remixed bars proved that different
types of SCMs can be successfully used in reducing the expansive
effect of ASR. SCMs percentage by weight is highly dependent on
the SCM type. The result of this study will help avoiding future
losses due to ASR cracking in construction project and reduce the
maintenance, repair, and replacement budgets required for highways
network.
Abstract: This article considers the problems of economic growth
and Russian energy strategy. Also in this paper, the issues related to
the economic growth prospects of Russian were discussed. Russian
energy strategy without standing Russia`s stature in global energy
markets, at the current production and extraction rates, will not be able
to sustain its own production as well as fulfil its energy strategy.
Indeed, Russia’s energy sector suffers from a chronic lack of
investments which are necessary to modernize its energy supply
system. In recent years, especially since the international financial
crisis, Russia-EU energy cooperation has made substantive progress.
Recently the break-through progress has been made, resulting mainly
from long-term contributing factors between the countries and recent
international economic and political situation changes. Analytical
material presented in the article is intended for a more detailed or
substantive analysis related to foreign economic relations of the
countries and Russia as well.
Abstract: The cumulative costs for O&M may represent as
much as 65%-90% of the turbine's investment cost. Nowadays the
cost effectiveness concept becomes a decision-making and
technology evaluation metric. The cost of energy metric accounts for
the effect replacement cost and unscheduled maintenance cost
parameters. One key of the proposed approach is the idea of
maintaining the WTs which can be captured via use of a finite state
Markov chain. Such a model can be embedded within a probabilistic
operation and maintenance simulation reflecting the action to be
done. In this paper, an approach of estimating the cost of O&M is
presented. The finite state Markov model is used for decision
problems with number of determined periods (life cycle) to predict
the cost according to various options of maintenance.
Abstract: The railway transport is considered as a one of the
most environmentally friendly mode of transport. With future
prediction of increasing of freight transport there are lines facing
problems with demanded capacity. Increase of the track capacity
could be achieved by infrastructure constructive adjustments. The
contribution shows how the travel time can be minimized and the
track capacity increased by changing some of the basic infrastructure
and operation parameters, for example, the minimal curve radius of
the track, the number of tracks, or the usable track length at stations.
Calculation of the necessary parameter changes is based on the
fundamental physical laws applied to the train movement, and
calculation of the occupation time is dependent on the changes of
controlling the traffic between the stations.
Abstract: This paper discusses the intake of combining multi-criteria
decision analysis (MCDA) with OLAP systems, to generate
an integrated analysis process dealing with complex multi-criteria
decision-making situations. In this context, a multi-agent modeling is
presented for decision support systems by combining multi-criteria
decision analysis (MCDA) with OLAP systems. The proposed
modeling which consists in performing the multi-agent system
(MAS) architecture, procedure and protocol of the negotiation model
is elaborated as a decision support tool for complex decision-making
environments. Our objective is to take advantage from the multi-agent
system which distributes resources and computational
capabilities across interconnected agents, and provide a problem
modeling in terms of autonomous interacting component-agents.
Thus, the identification and evaluation of criteria as well as the
evaluation and ranking of alternatives in a decision support situation
will be performed by organizing tasks and user preferences between
different agents in order to reach the right decision. At the end, an
illustrative example is conducted to demonstrate the function and
effectiveness of our MAS modeling.
Abstract: Large scale Indian manufacturers started
implementing Six Sigma to their supply core to fulfill the endless
need of high quality products. As well, they initiated encouraging
their suppliers to apply the well-ascertain SS management practice
and kept no resource for supplier enterprises, generally small midsized
enterprises to think for the admittance of Six Sigma as a quality
promotion drive. There are many issues to study for requisite changes
before the introduction of Six Sigma in auto SMEs. This paper
converges on impeding factors while implementing SS drive and also
pinpoints the gains achieved through successful implementation. The
result of this study suggest some operational guidelines for effective
implementation of Six Sigma from evidences acquired through
research questionnaire and interviews with industrial professionals,
apportioned to assort auto sector mid-sized enterprises (MSEs) in
India.
Abstract: Nowadays, food safety is a great public concern;
therefore, robust and effective techniques are required for detecting
the safety situation of goods. Hyperspectral Imaging (HSI) is an
attractive material for researchers to inspect food quality and safety
estimation such as meat quality assessment, automated poultry
carcass inspection, quality evaluation of fish, bruise detection of
apples, quality analysis and grading of citrus fruits, bruise detection
of strawberry, visualization of sugar distribution of melons,
measuring ripening of tomatoes, defect detection of pickling
cucumber, and classification of wheat kernels. HSI can be used to
concurrently collect large amounts of spatial and spectral data on the
objects being observed. This technique yields with exceptional
detection skills, which otherwise cannot be achieved with either
imaging or spectroscopy alone. This paper presents a nonlinear
technique based on kernel Fukunaga-Koontz transform (KFKT) for
detection of fat content in ground meat using HSI. The KFKT which
is the nonlinear version of FKT is one of the most effective
techniques for solving problems involving two-pattern nature. The
conventional FKT method has been improved with kernel machines
for increasing the nonlinear discrimination ability and capturing
higher order of statistics of data. The proposed approach in this paper
aims to segment the fat content of the ground meat by regarding the
fat as target class which is tried to be separated from the remaining
classes (as clutter). We have applied the KFKT on visible and nearinfrared
(VNIR) hyperspectral images of ground meat to determine
fat percentage. The experimental studies indicate that the proposed
technique produces high detection performance for fat ratio in ground
meat.
Abstract: Centrifugal-casting machine is used in manufacturing
special machine components like multi-layer journal bearing used in
all internal combustion engine, steam, gas turbine and air craft turboengine
where isotropic properties and high precisions are desired.
Moreover, this machine can be used in manufacturing thin wall hightech
machine components like cylinder liners and piston rings of IC
engine and other machine parts like sleeves, and bushes. Heavy-duty
machine component like railway wheel can also be prepared by
centrifugal casting. A lot of technological developments are required
in casting process for production of good casted machine body and
machine parts. Usually defects like blowholes, surface roughness,
chilled surface etc. are found in sand casted machine parts. But these
can be removed by centrifugal casting machine using rotating
metallic die. Moreover, die rotation, its temperature control, and good
pouring practice can contribute to the quality of casting because of
the fact that the soundness of a casting in large part depends upon
how the metal enters into the mold or dies and solidifies. Poor
pouring practice leads to variety of casting defects such as
temperature loss, low quality casting, excessive turbulence, over
pouring etc. Besides these, handling of molten metal is very
unsecured and dangerous for the workers. In order to get rid of all
these problems, the need of an automatic pouring device arises. In
this research work, a robot assisted pouring device and a centrifugal
casting machine are designed, developed constructed and tested
experimentally which are found to work satisfactorily. The robot
assisted pouring device is further modified and developed for using it
in actual metal casting process. Lot of settings and tests are required
to control the system and ultimately it can be used in automation of
centrifugal casting machine to produce high-tech machine parts with
desired precision.
Abstract: A composite material with carbon fiber and polymer
matrix has been used as adherent for manufacturing adhesive joints.
In order to evaluate different fiber orientations on joint performance,
the adherents with the 0°, ±15°, ±30°, ±45° fiber orientations were
used in the single lap joint configuration. The joints with an overlap
length of 25 mm were prepared according to the ASTM 1002
specifications and subjected to tensile loadings. The structural
adhesive used was a two-part epoxy to be cured at 70°C for an hour.
First, mechanical behaviors of the adherents were measured using
three point bending test. In the test, considerations were given to
stress to failure and elastic modulus. The results were compared with
theoretical ones using rule of mixture. Then, the joints were
manufactured in a specially prepared jig, after a proper surface
preparation. Experimental results showed that the fiber orientations
of the adherents affected the joint performance considerably; the
joints with ±45° adherents experienced the worst shear strength, half
of those with 0° adherents, and in general, there was a great
relationship between the fiber orientations and failure mechanisms.
Delamination problems were observed for many joints, which were
thought to be due to peel effects at the ends of the overlap. It was
proved that the surface preparation applied to the adherent surface
was adequate. For further explanation of the results, a numerical
work should be carried out using a possible non-linear analysis.
Abstract: Smart metering and demand response are gaining
ground in industrial and residential applications. Smart Appliances
have been given concern towards achieving Smart home. The success
of Smart grid development relies on the successful implementation of
Information and Communication Technology (ICT) in power sector.
Smart Appliances have been the technology under development and
many new contributions to its realization have been reported in the
last few years. The role of ICT here is to capture data in real time,
thereby allowing bi-directional flow of information/data between
producing and utilization point; that lead a way for the attainment of
Smart appliances where home appliances can communicate between
themselves and provide a self-control (switch on and off) using the
signal (information) obtained from the grid. This paper depicts the
background on ICT for smart appliances paying a particular attention
to the current technology and identifying the future ICT trends for
load monitoring through which smart appliances can be achieved to
facilitate an efficient smart home system which promote demand
response program. This paper grouped and reviewed the recent
contributions, in order to establish the current state of the art and
trends of the technology, so that the reader can be provided with a
comprehensive and insightful review of where ICT for smart
appliances stands and is heading to. The paper also presents a brief
overview of communication types, and then narrowed the discussion
to the load monitoring (Non-intrusive Appliances Load Monitoring
‘NALM’). Finally, some future trends and challenges in the further
development of the ICT framework are discussed to motivate future
contributions that address open problems and explore new
possibilities.
Abstract: E-Learning enables the users to learn at anywhere at
any time. In E-Learning systems, authenticating the E-Learning user
has security issues. The usage of appropriate communication
networks for providing the internet connectivity for E-learning is
another challenge. WiMAX networks provide Broadband Wireless
Access through the Multicast Broadcast Service so these networks
can be most suitable for E-Learning applications. The authentication
of E-Learning user is vulnerable to session hijacking problems. The
repeated authentication of users can be done to overcome these
issues. In this paper, session based Profile Caching Authentication is
proposed. In this scheme, the credentials of E-Learning users can be
cached at authentication server during the initial authentication
through the appropriate subscriber station. The proposed cache based
authentication scheme performs fast authentication by using cached
user profile. Thus, the proposed authentication protocol reduces the
delay in repeated authentication to enhance the security in ELearning.
Abstract: Mumbai, being traditionally the epicenter of India's
trade and commerce, the existing major ports such as Mumbai and
Jawaharlal Nehru Ports (JN) situated in Thane estuary are also
developing its waterfront facilities. Various developments over the
passage of decades in this region have changed the tidal flux
entering/leaving the estuary. The intake at Pir-Pau is facing the
problem of shortage of water in view of advancement of shoreline,
while jetty near Ulwe faces the problem of ship scheduling due to
existence of shallower depths between JN Port and Ulwe Bunder. In
order to solve these problems, it is inevitable to have information
about tide levels over a long duration by field measurements.
However, field measurement is a tedious and costly affair;
application of artificial intelligence was used to predict water levels
by training the network for the measured tide data for one lunar tidal
cycle. The application of two layered feed forward Artificial Neural
Network (ANN) with back-propagation training algorithms such as
Gradient Descent (GD) and Levenberg-Marquardt (LM) was used to
predict the yearly tide levels at waterfront structures namely at Ulwe
Bunder and Pir-Pau. The tide data collected at Apollo Bunder, Ulwe,
and Vashi for a period of lunar tidal cycle (2013) was used to train,
validate and test the neural networks. These trained networks having
high co-relation coefficients (R= 0.998) were used to predict the tide
at Ulwe, and Vashi for its verification with the measured tide for the
year 2000 & 2013. The results indicate that the predicted tide levels
by ANN give reasonably accurate estimation of tide. Hence, the
trained network is used to predict the yearly tide data (2015) for
Ulwe. Subsequently, the yearly tide data (2015) at Pir-Pau was
predicted by using the neural network which was trained with the
help of measured tide data (2000) of Apollo and Pir-Pau. The analysis of measured data and study reveals that: The
measured tidal data at Pir-Pau, Vashi and Ulwe indicate that there is
maximum amplification of tide by about 10-20 cm with a phase lag
of 10-20 minutes with reference to the tide at Apollo Bunder
(Mumbai). LM training algorithm is faster than GD and with increase
in number of neurons in hidden layer and the performance of the
network increases. The predicted tide levels by ANN at Pir-Pau and
Ulwe provides valuable information about the occurrence of high and
low water levels to plan the operation of pumping at Pir-Pau and
improve ship schedule at Ulwe.
Abstract: Our purpose is to investigate how the relationship
between employees and innovation management processes can drive
organizations to successful innovations. This research is deeply
related to a new way of thinking about human resources management
practices. It’s not simply about improving the employees’
engagement, but rather about a different and more radical
commitment: the employee can take on the role traditionally played
by the customer, namely to become the first tester of an innovative
product or service, the first user/customer and eventually the first
investor in the innovation. This new perception of employees could
create the basis of a novelty in the innovation process where
innovation is taken to a next level when the problems with customer
driven innovation on the one hand, and employees driven innovation
on the other can be balanced. This research identifies an effective
approach to innovation where the employees will participate
throughout the whole innovation process, not only in the idea
creation but also in the idea definition and development by giving
feedback in parallel to that provided by customers and lead-users.
Abstract: Energy consumption data, in particular those involving
public buildings, are impacted by many factors: the building structure,
climate/environmental parameters, construction, system operating
condition, and user behavior patterns. Traditional methods for data
analysis are insufficient. This paper delves into the data mining
technology to determine its application in the analysis of building
energy consumption data including energy consumption prediction,
fault diagnosis, and optimal operation. Recent literature are reviewed
and summarized, the problems faced by data mining technology in the
area of energy consumption data analysis are enumerated, and research
points for future studies are given.
Abstract: This paper outlines the development of an
experimental technique in quantifying supersonic jet flows, in an
attempt to avoid seeding particle problems frequently associated with
particle-image velocimetry (PIV) techniques at high Mach numbers.
Based on optical flow algorithms, the idea behind the technique
involves using high speed cameras to capture Schlieren images of the
supersonic jet shear layers, before they are subjected to an adapted
optical flow algorithm based on the Horn-Schnuck method to
determine the associated flow fields. The proposed method is capable
of offering full-field unsteady flow information with potentially
higher accuracy and resolution than existing point-measurements or
PIV techniques. Preliminary study via numerical simulations of a
circular de Laval jet nozzle successfully reveals flow and shock
structures typically associated with supersonic jet flows, which serve
as useful data for subsequent validation of the optical flow based
experimental results. For experimental technique, a Z-type Schlieren
setup is proposed with supersonic jet operated in cold mode,
stagnation pressure of 4 bar and exit Mach of 1.5. High-speed singleframe
or double-frame cameras are used to capture successive
Schlieren images. As implementation of optical flow technique to
supersonic flows remains rare, the current focus revolves around
methodology validation through synthetic images. The results of
validation test offers valuable insight into how the optical flow
algorithm can be further improved to improve robustness and
accuracy. Despite these challenges however, this supersonic flow
measurement technique may potentially offer a simpler way to
identify and quantify the fine spatial structures within the shock shear
layer.
Abstract: With the increasing number of people reviewing
products online in recent years, opinion sharing websites has become
the most important source of customers’ opinions. Unfortunately,
spammers generate and post fake reviews in order to promote or
demote brands and mislead potential customers. These are notably
destructive not only for potential customers, but also for business
holders and manufacturers. However, research in this area is not
adequate, and many critical problems related to spam detection have
not been solved to date. To provide green researchers in the domain
with a great aid, in this paper, we have attempted to create a highquality
framework to make a clear vision on review spam-detection
methods. In addition, this report contains a comprehensive collection
of detection metrics used in proposed spam-detection approaches.
These metrics are extremely applicable for developing novel
detection methods.