Abstract: In this study, a fuzzy similarity approach for Arabic
web pages classification is presented. The approach uses a fuzzy
term-category relation by manipulating membership degree for the
training data and the degree value for a test web page. Six measures
are used and compared in this study. These measures include:
Einstein, Algebraic, Hamacher, MinMax, Special case fuzzy and
Bounded Difference approaches. These measures are applied and
compared using 50 different Arabic web pages. Einstein measure was
gave best performance among the other measures. An analysis of
these measures and concluding remarks are drawn in this study.
Abstract: Series of experimental tests were conducted on a
section of a 660 kW wind turbine blade to measure the pressure
distribution of this model oscillating in plunging motion. In order to
minimize the amount of data required to predict aerodynamic loads
of the airfoil, a General Regression Neural Network, GRNN, was
trained using the measured experimental data. The network once
proved to be accurate enough, was used to predict the flow behavior
of the airfoil for the desired conditions.
Results showed that with using a few of the acquired data, the
trained neural network was able to predict accurate results with
minimal errors when compared with the corresponding measured
values. Therefore with employing this trained network the
aerodynamic coefficients of the plunging airfoil, are predicted
accurately at different oscillation frequencies, amplitudes, and angles
of attack; hence reducing the cost of tests while achieving acceptable
accuracy.
Abstract: The classical temporal scan statistic is often used to
identify disease clusters. In recent years, this method has become as a
very popular technique and its field of application has been notably
increased. Many bioinformatic problems have been solved with this
technique. In this paper a new scan fuzzy method is proposed. The
behaviors of classic and fuzzy scan techniques are studied with
simulated data. ROC curves are calculated, being demonstrated the
superiority of the fuzzy scan technique.
Abstract: This paper analyzes the linkage between migration,
economic globalization and terrorism concerns. On a broad level, I
analyze Canadian economic and political considerations, searching
for causal relationships between political and economic actors on the
one hand, and Canadian immigration law on the other. Specifically,
the paper argues that there are contradictory impulses affecting state
sovereignty. These impulses are are currently being played out in the
field of Canadian immigration law through several proposed changes
to Canada-s Immigration and Refugee Protection Act (IRPA). These
changes reflect an ideological conception of sovereignty that is
intrinsically connected with decision-making capacity centered on an
individual. This conception of sovereign decision-making views
Parliamentary debate and bureaucratic inefficiencies as both equally
responsible for delaying essential decisions relating to the protection
of state sovereignty, economic benefits and immigration control This
paper discusses these concepts in relation to Canadian immigration
policy under Canadian governments over the past twenty five years.
Abstract: Isobaric vapor-liquid equilibrium measurements are reported for the binary mixtures of n-Butylamine and Triethylamine with Cumene at 97.3 kPa. The measurements have been performed using a vapor recirculating type (modified Othmer's) equilibrium still. The binary mixture of n-Butylamine + Cumene shows positive deviation from ideality. Triethylamine + Cumene mixture shows negligible deviation from ideality. None of the systems form an azeotrope. The activity coefficients have been calculated taking into consideration the vapor phase nonideality. The data satisfy the thermodynamic consistency test of Herington. The activity coefficients have been satisfactorily correlated by means of the Margules, NRTL, and Black equations. The activity coefficient values obtained by the UNIFAC model are also reported.
Abstract: In this paper, the periodic surveillance scheme has
been proposed for any convex region using mobile wireless sensor
nodes. A sensor network typically consists of fixed number of
sensor nodes which report the measurements of sensed data such as
temperature, pressure, humidity, etc., of its immediate proximity
(the area within its sensing range). For the purpose of sensing an
area of interest, there are adequate number of fixed sensor
nodes required to cover the entire region of interest. It implies
that the number of fixed sensor nodes required to cover a given
area will depend on the sensing range of the sensor as well as
deployment strategies employed. It is assumed that the sensors to
be mobile within the region of surveillance, can be mounted on
moving bodies like robots or vehicle. Therefore, in our
scheme, the surveillance time period determines the number of
sensor nodes required to be deployed in the region of interest.
The proposed scheme comprises of three algorithms namely:
Hexagonalization, Clustering, and Scheduling, The first algorithm
partitions the coverage area into fixed sized hexagons that
approximate the sensing range (cell) of individual sensor node.
The clustering algorithm groups the cells into clusters, each of
which will be covered by a single sensor node. The later
determines a schedule for each sensor to serve its respective cluster.
Each sensor node traverses all the cells belonging to the cluster
assigned to it by oscillating between the first and the last cell for
the duration of its life time. Simulation results show that our
scheme provides full coverage within a given period of time using
few sensors with minimum movement, less power consumption,
and relatively less infrastructure cost.
Abstract: Today-s children, who are born into a more colorful,
more creative, more abstract and more accessible communication
environment than their ancestors as a result of dizzying advances in
technology, have an interesting capacity to perceive and make sense
of the world. Millennium children, who live in an environment where
all kinds of efforts by marketing communication are more intensive
than ever are, from their early childhood on, subject to all kinds of
persuasive messages. As regards advertising communication, it
outperforms all the other marketing communication efforts in
creating little consumer individuals and, as a result of processing of
codes and signs, plays a significant part in building a world of seeing,
thinking and understanding for children. Children who are raised with
metaphorical expressions such as tales and riddles also meet that fast
and effective meaning communication in advertisements.
Children-s perception of metaphors, which help grasp the “product
and its promise" both verbally and visually and facilitate association
between them is the subject of this study. Stimulating and activating
imagination, metaphors have unique advantages in promoting the
product and its promise especially in regard to print advertisements,
which have certain limitations. This study deals comparatively with
both literal and metaphoric versions of print advertisements
belonging to various product groups and attempts to discover to what
extent advertisements are liked, recalled, perceived and are
persuasive. The sample group of the study, which was conducted in
two elementary schools situated in areas that had different socioeconomic
features, consisted of children aged 12.
Abstract: Nowadays, the importance of energy saving is clearance to everyone. By attention to increasing price of fuels and also the problems of environment pollutions, there are the most efforts for using fuels littler and more optimum in everywhere. This essay studies optimizing of gas consumption in gas-burner space heaters. In oven of each gas-burner space heaters there is two snags to prevent the hot air (the result of combustion of natural gas) to go out of oven of the gas-burner space heaters directly without delivering its heat to the space of favorite environment like a room. These snags cause a excess circulating that helps hot air deliver its heat to the space of favorite environment. It means the exhaust air temperature will be decreased then when there are no snags. This is the aim of this essay to use maximum potential energy of the natural gas to make heat. In this study, by the help of a finite volume software (FLUENT) consumption of the gas-burner space heaters is simulated and optimized. At the end of this writing, by comparing the results of software and experimental results, it will be proved the authenticity of this method.
Abstract: In this work, the effects of scale on thermal behavior of the slab in a walking-beam type reheating furnace is studied by considering scale formation and growth in a furnace environment. Also, mathematical heat transfer model to predict the thermal radiation in a complex shaped reheating furnace with slab and skid buttons is developed with combined nongray WSGGM and blocked-off solution procedure. The model can attack the heat flux distribution within the furnace and the temperature distribution in the slab throughout the reheating furnace process by considering the heat exchange between the slab and its surroundings, including the radiant heat transfer among the slabs, the skids, the hot combustion gases and the furnace wall as well as the gas convective heat transfer in the furnace. With the introduction of the mathematical formulations validation of the present numerical model is conducted by calculating two example problems of blocked-off and nongray gas radiative heat transfer. After discussing the formation and growth of the scale on the slab surface, slab heating characteristics with scale is investigated in terms of temperature rise with time.
Abstract: The complex shape of the human pelvic bone was
successfully imaged and modeled using finite element FE processing.
The bone was subjected to quasi-static and dynamic loading
conditions simulating the effect of both weight gain and impact.
Loads varying between 500 – 2500 N (~50 – 250 Kg of weight) was
used to simulate 3D quasi-static weight gain. Two different 3D
dynamic analyses, body free fall at two different heights (1 and 2 m)
and forced side impact at two different velocities (20 and 40 Km/hr)
were also studied. The computed resulted stresses were compared for
the four loading cases, where Von Misses stresses increases linearly
with the weight gain increase under quasi-static loading. For the
dynamic models, the Von Misses stress history behaviors were
studied for the affected area and effected load with respect to time.
The normalization Von Misses stresses with respect to the applied
load were used for comparing the free fall and the forced impact load
results. It was found that under the forced impact loading condition
an over lapping behavior was noticed, where as for the free fall the
normalized Von Misses stresses behavior was found to nonlinearly
different. This phenomenon was explained through the energy
dissipation concept. This study will help designers in different
specialization in defining the weakest spots for designing different
supporting systems.
Abstract: This paper summaries basic principles and concepts of
intelligent controls, implemented in humanoid robotics as well as
recent algorithms being devised for advanced control of humanoid
robots. Secondly, this paper presents a new approach neuro-fuzzy
system. We have included some simulating results from our
computational intelligence technique that will be applied to our
humanoid robot. Subsequently, we determine a relationship between
joint trajectories and located forces on robot-s foot through a
proposed neuro-fuzzy technique.
Abstract: Discrete Cosine Transform (DCT) based transform coding is very popular in image, video and speech compression due to its good energy compaction and decorrelating properties. However, at low bit rates, the reconstructed images generally suffer from visually annoying blocking artifacts as a result of coarse quantization. Lapped transform was proposed as an alternative to the DCT with reduced blocking artifacts and increased coding gain. Lapped transforms are popular for their good performance, robustness against oversmoothing and availability of fast implementation algorithms. However, there is no proper study reported in the literature regarding the statistical distributions of block Lapped Orthogonal Transform (LOT) and Lapped Biorthogonal Transform (LBT) coefficients. This study performs two goodness-of-fit tests, the Kolmogorov-Smirnov (KS) test and the 2- test, to determine the distribution that best fits the LOT and LBT coefficients. The experimental results show that the distribution of a majority of the significant AC coefficients can be modeled by the Generalized Gaussian distribution. The knowledge of the statistical distribution of transform coefficients greatly helps in the design of optimal quantizers that may lead to minimum distortion and hence achieve optimal coding efficiency.
Abstract: Let n be an integer. We show the existence of at least
three non-isomorphic non-commutative Latin squares of order n
which are embeddable in groups when n ≥ 5 is odd. By using a
similar construction for the case when n ≥ 4 is even, we show that
certain non-commutative Latin squares of order n are not embeddable
in groups.
Abstract: The effect of plant growth-promoting rhizobacteria
(PGPR) on seed germination, seedling growth and yield of field
grown maize were evaluated in three experiments. In these
experiments six bacterial strains include P.putida strain R-168,
P.fluorescens strain R-93, P.fluorescens DSM 50090, P.putida
DSM291, A.lipoferum DSM 1691, A.brasilense DSM 1690 were
used. Results of first study showed seed Inoculation significantly
enhanced seed germination and seedling vigour of maize. In second
experiment, leaf and shoot dry weight and also leaf surface area
significantly were increased by bacterial inoculation in both sterile
and non-sterile soil. The results showed that inoculation with
bacterial treatments had a more stimulating effect on growth and
development of plants in nonsterile than sterile soil. In the third
experiment, Inoculation of maize seeds with all bacterial strains
significantly increased plant height, 100 seed weight, number of seed
per ear and leaf area .The results also showed significant increase in
ear and shoot dry weight of maize.
Abstract: The Constraints imposed by non-thermal
leptogenesis on the survival of the neutrino mass models describing
the presently available neutrino mass patterns, are studied
numerically. We consider the Majorana CP violating phases coming
from right-handed Majorana mass matrices to estimate the baryon
asymmetry of the universe, for different neutrino mass models
namely quasi-degenerate, inverted hierarchical and normal
hierarchical models, with tribimaximal mixings. Considering two
possible diagonal forms of Dirac neutrino mass matrix as either
charged lepton or up-quark mass matrix, the heavy right-handed
mass matrices are constructed from the light neutrino mass matrix.
Only the normal hierarchical model leads to the best predictions of
baryon asymmetry of the universe, consistent with observations in
non-thermal leptogenesis scenario.
Abstract: Working memory (WM) can be defined as the system
which actively holds information in the mind to do tasks in spite of
the distraction. Contrary, short-term memory (STM) is a system that
represents the capacity for the active storing of information without
distraction. There has been accumulating evidence that these types of
memory are related to higher cognition (HC). The aim of this study
was to verify the relationship between HC and memory (visual STM
and WM, auditory STM and WM). 59 primary school children were
tested by intelligence test, mathematical tasks (HC) and memory
subtests. We have shown that visual but not auditory memory is a
significant predictor of higher cognition. The relevance of these
results are discussed.
Abstract: An incentive for performance, as one subsystem of a
new performance management system, has been implemented in the
Thai public sector since 2004. This research investigates the
development of organizational justice in the incentive allocation by
comparing the roles of distributive and procedural justice on national
personnel-s attitudinal outcomes (incentive satisfaction and job
performance) between 2 periods, i.e. 2006 and 2008. The data were
collected via self-administered questionnaires completed by national
government officers and employees. They were stratified using multistage
sampling with 2,600 usable samples or 72.0% response rate in
2006, and 1,969 usable samples or 59.3% in 2008. The findings are:
(1) There is no difference in means between the two periods relating
to distributive justice, procedural justice, incentive satisfaction and
job performance. (2) Distributive justice and procedural justice
played more important roles in predicting incentive satisfaction and
job performance in 2008 than in 2006.
Abstract: The unique structural configuration found in human foot allows easy walking. Similar movement is hard to imitate even for an ape. It is obvious that human ambulation relates to the foot structure itself. Suppose the bones are represented as vertices and the joints as edges. This leads to the development of a special graph that represents human foot. On a footprint there are point-ofcontacts which have contact with the ground. It involves specific vertices. Theoretically, for an ideal ambulation, these points provide reactions onto the ground or the static equilibrium forces. They are arranged in sequence in form of a path. The ambulating footprint follows this path. Having the human foot graph and the path crossbred, it results in a representation that describes the profile of an ideal ambulation. This profile cites the locations where the point-of-contact experience normal reaction forces. It highlights the significant of these points.
Abstract: When considering the development of constitutive
equations describing the behavior of materials under cyclic plastic
strains, different kinds of formulations can be adopted. The primary
intention of this study is to develop computer programming of
plasticity models to accurately predict the life of engineering
components. For this purpose, the energy or cyclic strain is computed
in multi-surface plasticity models in non-proportional loading and to
present their procedures and codes results.
Abstract: This paper To get the angle value with a MEMS rate
gyroscope in some specific field, the usual method is to make an
integral operation to the rate output, which will lead the error
cumulating effect. So the rate gyro is not suitable. MEMS rate
integrating gyroscope (MRIG) will solve this problem. A DSP system
has been developed to implement the control arithmetic. The system
can measure the angle of rotation directly by the control loops that
make the sensor work in whole-angle mode. Modeling the system with
MATLAB, desirable results of angle outputs are got, which prove the
feasibility of the control arithmetic.