Abstract: Drinking water is one of the most valuable resources
available to mankind. The presence of pathogens in drinking water is
highly undesirable. Because of the Lateritic soil, the iron
concentrations were high in ground water. High concentration of iron
and other trace elements could restrict bacterial growth and modify
their metabolic pattern as well. The bacterial growth rate reduced in
the presence of iron in water. This paper presents the results of a
controlled laboratory study conducted to assess the inhibition of
micro-organism (pathogen) in well waters in the presence of
dissolved iron concentrations. Synthetic samples were studied in the
laboratory and the results compared with field samples. Predictive
model for microbial inhibition in the presence of iron is presented. It
was seen that the bore wells, open wells and the field results varied,
probably due to the nature of micro-organism utilizing the iron in
well waters.
Abstract: The pavement constructions on soft and expansive soils are not durable and unable to sustain heavy traffic loading. As a result, pavement failures and settlement problems will occur very often even under light traffic loading due to cyclic and rolling effects. Geotechnical engineers have dwelled deeply into this matter, and adopt various methods to improve the engineering characteristics of soft fine-grained soils and expansive soils. The problematic soils are either replaced by good and better quality material or treated by using chemical stabilization with various binding materials. Increased the strength and durability are also the part of the sustainability drive to reduce the environment footprint of the built environment by the efficient use of resources and waste recycle materials. This paper presents a series of laboratory tests and evaluates the effect of cement and fly ash on the strength and drainage characteristics of soil in Miri. The tests were performed at different percentages of cement and fly ash by dry weight of soil. Additional tests were also performed on soils treated with the combinations of fly ash with cement and lime. The results of this study indicate an increase in unconfined compression strength and a decrease in hydraulic conductivity of the treated soil.
Abstract: There are three approaches to complete Bayesian
Network (BN) model construction: total expert-centred, total datacentred,
and semi data-centred. These three approaches constitute the
basis of the empirical investigation undertaken and reported in this
paper. The objective is to determine, amongst these three
approaches, which is the optimal approach for the construction of a
BN-based model for the performance assessment of students-
laboratory work in a virtual electronic laboratory environment. BN
models were constructed using all three approaches, with respect to
the focus domain, and compared using a set of optimality criteria. In
addition, the impact of the size and source of the training, on the
performance of total data-centred and semi data-centred models was
investigated. The results of the investigation provide additional
insight for BN model constructors and contribute to literature
providing supportive evidence for the conceptual feasibility and
efficiency of structure and parameter learning from data. In addition,
the results highlight other interesting themes.
Abstract: This paper reviews the objectives, methods and results of previous studies on biodrying of solid waste in several countries. Biodrying of solid waste is a novel technology in developing countries such as in Malaysia where high moisture content in organic waste makes the segregation process for recycling purposes complicated and diminishes the calorific value for the use of fuel source. In addition, the high moisture content also encourages the breeding of vectors and disease-bearing animals. From the laboratory results, the average moisture content of organic waste, paper, plastics and metals are 58.17%, 37.93%, 29.79% and 1.03% respectively for UKM campus. Biodrying of solid waste is a simple method of waste treatment as well as a cost-efficient technology to dry the solid waste. The process depends on temperature monitoring and air flow control along with the natural biodegradable process of organic waste. This review shows that the biodrying of solid waste method has high potential in treatment and recycling of solid waste, be useful for biodrying study and implementation in Malaysia.
Abstract: Economically transformers constitute one of the largest investments in a Power system. For this reason, transformer condition assessment and management is a high priority task. If a transformer fails, it would have a significant negative impact on revenue and service reliability. Monitoring the state of health of power transformers has traditionally been carried out using laboratory Dissolved Gas Analysis (DGA) tests performed at periodic intervals on the oil sample, collected from the transformers. DGA of transformer oil is the single best indicator of a transformer-s overall condition and is a universal practice today, which started somewhere in the 1960s. Failure can occur in a transformer due to different reasons. Some failures can be limited or prevented by maintenance. Oil filtration is one of the methods to remove the dissolve gases and prevent the deterioration of the oil. In this paper we analysis the DGA data by regression method and predict the gas concentration in the oil in the future. We bring about a comparative study of different traditional methods of regression and the errors generated out of their predictions. With the help of these data we can deduce the health of the transformer by finding the type of fault if it has occurred or will occur in future. Additional in this paper effect of filtration on the transformer health is highlight by calculating the probability of failure of a transformer with and without oil filtrating.
Abstract: In India, the quarrel between the budding human
populace and the planet-s unchanging supply of freshwater and
falling water tables has strained attention the reuse of gray water as
an alternative water resource in rural development. This paper
present the finest design of laboratory scale gray water treatment
plant, which is a combination of natural and physical operations such
as primary settling with cascaded water flow, aeration, agitation and
filtration, hence called as hybrid treatment process. The economical
performance of the plant for treatment of bathrooms, basins and
laundries gray water showed in terms of deduction competency of
water pollutants such as COD (83%), TDS (70%), TSS (83%), total
hardness (50%), oil and grease (97%), anions (46%) and cations
(49%). Hence, this technology could be a good alternative to treat
gray water in residential rural area.
Abstract: Fructooligosaccharides derived from microbial enzyme especially from fungal sources has been received particular attention due to its beneficial effects as prebiotics and mass production. However, fungal fermentation is always cumbersome due to its broth rheology problem that will eventually affect the production of FOS. This study investigated the efficiency of immobilized cell system using rotating fibrous bed bioreactor (RFBB) in producing fructooligosaccharides (FOS). A comparative picture with respect to conventional stirred tank bioreactor (CSTB) and RFBB has been presented. To demonstrate the effect of agitation intensity and aeration rate, a laboratory-scale bioreactor 2.5 L was operated in three phases (high, medium, low) for 48 hours. Agitation speed has a great influence on P. simplicissimum fermentation for FOS production, where the volumetric FOS productivity using RFBB is increased with almost 4 fold compared to the FOS productivity in CSTB that only 0.319 g/L/h. Rate of FOS production increased up to 1.2 fold when immobilized cells system was employed at aeration rate similar to the freely suspended cells at 2.0 vvm.
Abstract: In present work, drying characteristics of fresh papaya (Carica papaya L.) was studied to understand the dehydration process and its behavior. Drying experiments were carried out by a laboratory scaled microwave-vacuum oven. The parameters affecting drying characteristics including operating modes (continuous, pulsed), microwave power (400 and 800 W), and vacuum pressure (20, 30, and 40 cmHg) were investigated. For pulsed mode, two levels of power-off time (60 and 120 s) were used while the power-on time was fixed at 60 s and the vacuum pressure was fixed at 40 cmHg. For both operating modes, the effects of drying conditions on drying time, drying rate, and effective diffusivity were investigated. The results showed high microwave power, high vacuum, and pulsed mode of 60 s-on/60 s-off favored drying rate as shown by the shorten drying time and increased effective diffusivity. The drying characteristics were then described by Page-s model, which showed a good agreement with experimental data.
Abstract: For this study, this researcher conducted a precision
network adjustment with QOCA, the precision network adjustment
software developed by Jet Propulsion Laboratory, to perform an
integrated network adjustment on the Unified Control Points managed
by the National Geographic Information Institute. Towards this end,
275 Unified Control Points observed in 2008 were selected before a
network adjustment is performed on those 275 Unified Control Points.
The RMSE on the discrepancies of coordinates as compared to the
results of GLOBK was ±6.07mm along the N axis, ±2.68mm along the
E axis and ±6.49mm along the U axis.
Abstract: This study presents the performance of membrane
bioreactor in treating high phosphate wastewater. The laboratory
scale MBR was operated at permeate flux of 25 L/m2.h with a hollow
fiber membrane (polypropylene, approx. pore size 0.01 - 0.2 μm) at
hydraulic retention time (HRT) of 12 hrs. Scanning electron
microscopy (SEM) and energy diffusive X-ray (EDX) analyzer were
used to characterize the membrane foulants. Results showed that the
removal efficiencies of COD, TSS, NH3-N and PO4
3- were 93, 98, 80
and 30% respectively. On average 91% of influent soluble microbial
products (SMP) were eliminated, with the eliminations of
polysaccharides mostly above 80%. The main fouling resistance was
cake resistance. It should be noted that SMP were found in major
portions of mixed liquor that played a relatively significant role in
membrane fouling. SEM and EDX analyses indicated that the
foulants covering the membrane surfaces comprises not only organic
substances but also inorganic elements including Mg, Ca, Al, K and
P.
Abstract: Undoubtedly, chassis is one of the most important
parts of a vehicle. Chassis that today are produced for vehicles are
made up of four parts. These parts are jointed together by screwing.
Transverse parts are called cross member.
This study reviews the stress generated by cyclic laboratory loads
in front cross member of Peugeot 405. In this paper the finite element
method is used to simulate the welding process and to determine the
physical response of the spot-welded joints. Analysis is done by the
Abaqus software.
The Stresses generated in cross member structure are generally
classified into two groups: The stresses remained in form of residual
stresses after welding process and the mechanical stress generated by
cyclic load. Accordingly the total stress must be obtained by
determining residual stress and mechanical stress separately and then
sum them according to the superposition principle.
In order to improve accuracy, material properties including
physical, thermal and mechanical properties were supposed to be
temperature-dependent. Simulation shows that maximum Von Misses
stresses are located at special points. The model results are then
compared to the experimental results which are reported by
producing factory and good agreement is observed.
Abstract: Stuck-pipe in drilling operations is one of the most
pressing and expensive problems in the oil industry. This paper
describes a computational simulation and an experimental study of
the hydrodynamic vibrator, which may be used for liquidation of
stuck-pipe problems during well drilling. The work principle of the
vibrator is based upon the known phenomena of Vortex Street of
Karman and the resulting generation of vibrations. We will discuss
the computational simulation and experimental investigations of
vibrations in this device. The frequency of the vibration parameters
has been measured as a function of the wide range Reynolds Number.
The validity of the computational simulation and of the assumptions
on which it is based has been proved experimentally. The
computational simulation of the vibrator work and its effectiveness
was carried out using FLUENT software. The research showed high
degree of congruence with the results of the laboratory tests and
allowed to determine the effect of the granular material features upon
the pipe vibration in the well. This study demonstrates the potential
of using the hydrodynamic vibrator in a well drilling system.