Abstract: Three dimensional simulations are carried out to estimate the effect of wind direction, wind speed and geometry on the flow and dispersion of vehicular pollutant in a street canyon. The pollutant sources are motor vehicles passing between the two buildings. Suitable emission factors for petrol and diesel vehicles at varying vehicle speed are used for the estimation of the rate of emission from the streets. The dispersion of automobile pollutant released from the street is simulated by introducing vehicular emission source term as a fixed-flux boundary condition at the ground level over the road. The emission source term is suitably calculated by adopting emission factors from literature for varying conditions of street traffic. It is observed that increase in wind angle disturbs the symmetric pattern of pollution distribution along the street length. The concentration increases in the far end of the street as compared to the near end.
Abstract: Wind energy has been shown to be one of the most
viable sources of renewable energy. With current technology, the low
cost of wind energy is competitive with more conventional sources of
energy such as coal. Most blades available for commercial grade
wind turbines incorporate a straight span-wise profile and airfoil
shaped cross sections. These blades are found to be very efficient at
lower wind speeds in comparison to the potential energy that can be
extracted. However as the oncoming wind speed increases the
efficiency of the blades decreases as they approach a stall point. This
paper explores the possibility of increasing the efficiency of the
blades at higher wind speeds while maintaining efficiency at the
lower wind speeds. The design intends to maintain efficiency at
lower wind speeds by selecting the appropriate orientation and size
of the airfoil cross sections based on a low oncoming wind speed and
given constant rotation rate. The blades will be made more efficient
at higher wind speeds by implementing a swept blade profile.
Performance was investigated using the computational fluid
dynamics (CFD).
Abstract: This paper focuses on developing an integrated
reliable and sophisticated model for ultra large wind turbines And to
study the performance and analysis of vector control on large wind
turbines. With the advance of power electronics technology, direct
driven multi-pole radial flux PMSG (Permanent Magnet Synchronous
Generator) has proven to be a good choice for wind turbines
manufacturers. To study the wind energy conversion systems, it is
important to develop a wind turbine simulator that is able to produce
realistic and validated conditions that occur in real ultra MW wind
turbines. Three different packages are used to simulate this model,
namely, Turbsim, FAST and Simulink. Turbsim is a Full field wind
simulator developed by National Renewable Energy Laboratory
(NREL). The wind turbine mechanical parts are modeled by FAST
(Fatigue, Aerodynamics, Structures and Turbulence) code which is
also developed by NREL. Simulink is used to model the PMSG, full
scale back to back IGBT converters, and the grid.
Abstract: The flow field over a three dimensional pole barn
characterized by a cylindrical roof has been numerically investigated.
Wind pressure and viscous loads acting on the agricultural building
have been analyzed for several incoming wind directions, so as to
evaluate the most critical load condition on the structure. A constant
wind velocity profile, based on the maximum reference wind speed in
the building site (peak gust speed worked out for 50 years return
period) and on the local roughness coefficient, has been simulated.
In order to contemplate also the hazard due to potential air
wedging between the stored hay and the lower part of the ceiling, the
effect of a partial filling of the barn has been investigated.
The distribution of wind-induced loads on the structure have been
determined, allowing a numerical quantification of the effect of wind
direction on the induced stresses acting on a hemicylindrical roof.
Abstract: Power Spectral Density (PSD) of quasi-stationary processes can be efficiently estimated using the short time Fourier series (STFT). In this paper, an algorithm has been proposed that computes the PSD of quasi-stationary process efficiently using offline autoregressive model order estimation algorithm, recursive parameter estimation technique and modified sliding window discrete Fourier Transform algorithm. The main difference in this algorithm and STFT is that the sliding window (SW) and window for spectral estimation (WSA) are separately defined. WSA is updated and its PSD is computed only when change in statistics is detected in the SW. The computational complexity of the proposed algorithm is found to be lesser than that for standard STFT technique.
Abstract: In this paper, an improvement of PDLZW implementation
with a new dictionary updating technique is proposed. A
unique dictionary is partitioned into hierarchical variable word-width
dictionaries. This allows us to search through dictionaries in parallel.
Moreover, the barrel shifter is adopted for loading a new input string
into the shift register in order to achieve a faster speed. However,
the original PDLZW uses a simple FIFO update strategy, which is
not efficient. Therefore, a new window based updating technique
is implemented to better classify the difference in how often each
particular address in the window is referred. The freezing policy
is applied to the address most often referred, which would not be
updated until all the other addresses in the window have the same
priority. This guarantees that the more often referred addresses would
not be updated until their time comes. This updating policy leads
to an improvement on the compression efficiency of the proposed
algorithm while still keep the architecture low complexity and easy
to implement.
Abstract: This research simulates one of the natural phenomena,
the ocean wave. Our goal is to be able to simulate the ocean wave at
real-time rate with the water surface interacting with objects. The
wave in this research is calm and smooth caused by the force of the
wind above the ocean surface. In order to make the simulation of the
wave real-time, the implementation of the GPU and the
multithreading techniques are used here. Based on the fact that the
new generation CPUs, for personal computers, have multi cores, they
are useful for the multithread. This technique utilizes more than one
core at a time. This simulation is programmed by C language with
OpenGL. To make the simulation of the wave look more realistic, we
applied an OpenGL technique called cube mapping (environmental
mapping) to make water surface reflective and more realistic.
Abstract: The relationship between tropical cyclogenesis and solar activity is addressed in this paper, analyzing the relationship between important parameters in the evolution of tropical cyclones as the CAPE, wind shear and relative vorticity, and the Dst geomagnetic index as a parameter of solar activity. The apparent relationship between all this phenomena has a different response depending on the phase of the solar cycles.
Abstract: This paper presents a numerical analysis of the
performance of a three-bladed Darrieus vertical-axis wind turbine
based on the DU91-W2-250 airfoil. A complete campaign of 2-D
simulations, performed for several values of tip speed ratio and based
on RANS unsteady calculations, has been performed to obtain the
rotor torque and power curves. Rotor performances have been
compared with the results of a previous work based on the use of the
NACA 0021 airfoil. Both the power coefficient and the torque
coefficient have been determined as a function of the tip speed ratio.
The flow field around rotor blades has also been analyzed. As a final
result, the performance of the DU airfoil based rotor appears to be
lower than the one based on the NACA 0021 blade section. This
behavior could be due to the higher stall characteristics of the NACA
profile, being the separation zone at the trailing edge more extended
for the DU airfoil.
Abstract: This article is an extension and a practical application
approach of Wheeler-s NEBIC theory (Net Enabled Business
Innovation Cycle). NEBIC theory is a new approach in IS research
and can be used for dynamic environment related to new technology.
Firms can follow the market changes rapidly with support of the IT
resources. Flexible firms adapt their market strategies, and respond
more quickly to customers changing behaviors. When every leading
firm in an industry has access to the same IT resources, the way that
these IT resources are managed will determine the competitive
advantages or disadvantages of firm. From Dynamic Capabilities
Perspective and from newly introduced NEBIC theory by Wheeler,
we know that only IT resources cannot deliver customer value but
good configuration of those resources can guarantee customer value
by choosing the right emerging technology, grasping the right
economic opportunities through business innovation and growth. We
found evidences in literature that SOA (Service Oriented
Architecture) is a promising emerging technology which can deliver
the desired economic opportunity through modularity, flexibility and
loose-coupling. SOA can also help firms to connect in network which
can open a new window of opportunity to collaborate in innovation
and right kind of outsourcing. There are many articles and research
reports indicates that failure rate in outsourcing is very high but at the
same time research indicates that successful outsourcing projects
adds tangible and intangible benefits to the service consumer.
Business executives and policy makers in the west should not afraid
of outsourcing but they should choose the right strategy through the
use of emerging technology to significantly reduce the failure rate in
outsourcing.
Abstract: The development and application of wind power for
renewable energy has attracted growing interest in recent years. Renewable energy sources are attracting much alteration as they can
reduce both environmental damage and dependence on fossil fuels. With the growing need for sustainable energy supplies, a case is made
for decentralized, stand-alone power supplies (SAPS) as an alternative to power grids. In the era which traditional petroleum energy resource
decreasing and the green house affect significant increasing, the development and usage of regenerative resources is inevitable. Due to the contribution of the pioneers, the development of regenerative resources already has a remarkable achievement; however, in the view of economy and quantity, it is still a long road for regenerative energy
to replace traditional petroleum energy. In our prospective, in stead of
investigate larger regenerative energy equipment, it is much wiser to
think about the blind side and breakthrough of the current technique.
Abstract: The quality-of-service (QoS) support for wireless
LANs has been a hot research topic during the past few years. In this paper, two QoS provisioning mechanisms are proposed for the employment in 802.11e EDCA MAC scheme. First, the proposed call
admission control mechanism can not only guarantee the QoS for the higher priority existing connections but also provide the minimum reserved bandwidth for traffic flows with lower priority. In addition, the adaptive contention window adjustment mechanism can adjust the
maximum and minimum contention window size dynamically according to the existing connection number of each AC. The collision
probability as well as the packet delay will thus be reduced effectively.
Performance results via simulations have revealed the enhanced QoS property achieved by employing these two mechanisms.
Abstract: Launch and recovery helicopter wind envelope for a
ship type was determined as the first step to the helicopter
qualification program. Flight deck velocities data were obtained by
means of a two components laser Doppler anemometer testing a
1/50th model in the wind tunnel stream. Full-scale flight deck
measurements were obtained on board the ship using a sonic
anemometer. Wind tunnel and full-scale measurements were
compared, showing good agreement and finally, a preliminary launch
and recovery helicopter wind envelope for this specific ship was
built.
Abstract: With continuous rise of oil price, how to develop alternative energy source has become a hot topic around the world. This study discussed the dynamic characteristics of an island power system operating under random wind speed lower than nominal wind
speeds of wind turbines. The system primarily consists of three diesel engine power generation systems, three constant-speed variable-pitch wind turbines, a small hydraulic induction generation system, and lumped static loads. Detailed models based on Matlab/Simulink were developed to cater for the dynamic behavior of the system. The results suggested this island power system can operate stably in this operational mode. This study can serve as an important reference for planning, operation, and further expansion of island power systems.
Abstract: For micro-gyroscopes, the angular rate detection components have to oscillate forwards and backwards alternatively. An innovative design of micro-electromagnetic drive module is proposed to make a Π-type disc reciprocally and efficiently rotate within a certain of angular interval. Twelve Electromagnetic poles enclosing the thin disc are designed to provide the magnetic drive power. Isotropic etching technique is employed to fabricate the high-aspect-ratio trench, so that the contact angle of wire against trench can be increased and the potential defect of cavities and pores within the wire can be prevented. On the other hand, a Π-type thin disc is designed to conduct the pitch motion as an angular excitation, in addition to spinning, is exerted on the gyroscope. The efficacy of the micro-magnetic drive module is verified by the commercial software, Ansoft Maxewll. In comparison with the conventional planar windings in micro-scale systems, the magnetic drive force is increased by 150%.
Abstract: Traditionally, wind tunnel models are made of metal
and are very expensive. In these years, everyone is looking for ways
to do more with less. Under the right test conditions, a rapid
prototype part could be tested in a wind tunnel. Using rapid prototype
manufacturing techniques and materials in this way significantly
reduces time and cost of production of wind tunnel models. This
study was done of fused deposition modeling (FDM) and their ability
to make components for wind tunnel models in a timely and cost
effective manner. This paper discusses the application of wind tunnel
model configuration constructed using FDM for transonic wind
tunnel testing. A study was undertaken comparing a rapid
prototyping model constructed of FDM Technologies using
polycarbonate to that of a standard machined steel model. Testing
covered the Mach range of Mach 0.3 to Mach 0.75 at an angle-ofattack
range of - 2° to +12°. Results from this study show relatively
good agreement between the two models and rapid prototyping
Method reduces time and cost of production of wind tunnel models.
It can be concluded from this study that wind tunnel models
constructed using rapid prototyping method and materials can be
used in wind tunnel testing for initial baseline aerodynamic database
development.
Abstract: The aerodynamic performances of vertical axis wind
turbines are highly affected by tip vortexes. In the present
work, different tip devices are considered and simulated against
a baseline rotor configuration, with the aim of identifying the
best tip architecture. Three different configurations are tested:
winglets, an elliptic termination and an aerodynamic bulkhead.
A comparative analysis on the most promising architectures is
conducted, focusing also on blade torque evolution during a full
revolution of the rotor blade. The most promising technology is
concluded to be a well designed winglet.
Abstract: In this work, an attempt is made to design an optimal
wind/pv/diesel hybrid power system for a village of Ain Merane,
Chlef, Algeria, where the wind speed and solar radiation
measurements were made. The aim of this paper is the optimization
of a hybrid wind/solar/diesel system applied in term of technical and
economic feasibility by simulation using HOMER. A comparison
was made between the performance of wind/pv/diesel system and the
classic connecting system.
Abstract: This study investigated the climatic factors associated
with Influenza incidence in Nakhon Si Thammarat, Southern
Thailand. Climatic factors comprised of the amount of rainfall,
percent of rainy days, relative humidity, wind speed, maximum,
minimum temperatures and temperature difference. A multiple
stepwise regression technique was used to fit the statistical model.
The result showed that the temperature difference and percent of
rainy days were positively associated with Influenza incidence in
Nakhon Si Thammarat.
Abstract: A multiple-option analytical model for the evaluation of the energy performance and distribution of aerodynamic forces acting on a vertical-axis Darrieus wind turbine depending on both rotor architecture and operating conditions is presented. For this purpose, a numerical algorithm, capable of generating the desired rotor conformation depending on design geometric parameters, is coupled to a Single/Double-Disk Multiple-Streamtube Blade Element – Momentum code. Both single and double-disk configurations are analyzed and model predictions are compared to literature experimental data in order to test the capability of the code for predicting rotor performance. Effective airfoil characteristics based on local blade Reynolds number are obtained through interpolation of literature low-Reynolds airfoil databases. Some corrections are introduced inside the original model with the aim of simulating also the effects of blade dynamic stall, rotor streamtube expansion and blade finite aspect ratio, for which a new empirical relationship to better fit the experimental data is proposed. In order to predict also open field rotor operation, a freestream wind shear profile is implemented, reproducing the effect of atmospheric boundary layer.