Abstract: This paper presents a novel three-phase utility
frequency to high frequency soft switching power conversion circuit
with dual mode pulse width modulation and pulse density modulation
for high power induction heating applications as melting of steel and
non ferrous metals, annealing of metals, surface hardening of steel
and cast iron work pieces and hot water producers, steamers and
super heated steamers. This high frequency power conversion circuit
can operate from three-phase systems to produce high current for
high power induction heating applications under the principles of
ZVS and it can regulate its ac output power from the rated value to a
low power level. A dual mode modulation control scheme based on
high frequency PWM in synchronization with the utility frequency
positive and negative half cycles for the proposed high frequency
conversion circuit and utility frequency pulse density modulation is
produced to extend its soft switching operating range for wide ac
output power regulation. A dual packs heat exchanger assembly is
designed to be used in consumer and industrial fluid pipeline systems
and it is proved to be suitable for the hot water, steam and super
heated steam producers. Experiment and simulation results are given
in this paper to verify the operation principles of the proposed ac
conversion circuit and to evaluate its power regulation and
conversion efficiency. Also, the paper presents a mutual coupling
model of the induction heating load instead of equivalent transformer
circuit model.
Abstract: The objective of this paper is to present a
comparative study of Homotopy Perturbation Method (HPM),
Variational Iteration Method (VIM) and Homotopy Analysis
Method (HAM) for the semi analytical solution of Kortweg-de
Vries (KdV) type equation called KdV. The study have been
highlighted the efficiency and capability of aforementioned methods
in solving these nonlinear problems which has been arisen from a
number of important physical phenomenon.
Abstract: Quality of school meals is one of the major concerns of governments and international organizations worldwide. This study aims to evaluate nutritional compliance of meals served at a Portuguese primary school considering the portions stated by Portuguese Education Ministry. To evaluate adequacy of portions served, weighing of all meal components offered to students and leftovers was performed during ten consecutive days at two different moments. Plate waste (%) was calculated by the ratio of food discarded and food served to the children. Nutritional evaluation of menus was made using the Portuguese Food Composition Table. Meals evaluated showed a percent contribution to energetic daily intake higher than recommendations. Meals served to children were considered high energy and protein dense. No significant waste of soup was accounted and the main meal components wasted were fish and vegetables. It will be necessary to adjust portions indicated by Ministry of Education in order to comply with recommendations and reduce food waste.
Abstract: Due to adverse pressure gradient along the diverging
walls of wide-angled diffusers, the attached flow separates from
one wall and remains attached permanently to the other wall in a
process called stalling. Stalled diffusers render the whole fluid flow
system, in which they are part of, very inefficient. There is then an
engineering need to try to understand the whole process of diffuser
stall if any meaningful attempts to improve on diffuser efficiency
are to be made. In this regard, this paper provides a data bank
contribution for the mean flow-field in wide-angled diffusers where
the complete velocity and static pressure fields, and pressure recovery
data for diffusers in the fully stalled flow regime are experimentally
measured. The measurements were carried out at Reynolds numbers
between 1.07×105 and 2.14×105 based on inlet hydraulic diameter
and centreline velocity for diffusers whose divergence angles were
between 30Ôùª and 50Ôùª. Variation of Reynolds number did not significantly
affect the velocity and static pressure profiles. The wall static
pressure recovery was found to be more sensitive to changes in the
Reynolds number. By increasing the velocity from 10 m/s to 20 m/s,
the wall static pressure recovery increased by 8.31%. However, as the
divergence angle was increased, a similar increase in the Reynolds
number resulted in a higher percentage increase in pressure recovery.
Experimental results showed that regardless of the wall to which
the flow was attached, both the velocity and pressure fields were
replicated with discrepancies below 2%.
Abstract: Most HWRs currently use natural uranium fuel. Using enriched uranium fuel results in a significant improvement in fuel cycle costs and uranium utilization. On the other hand, reactivity changes of HWRs over the full range of operating conditions from cold shutdown to full power are small. This reduces the required reactivity worth of control devices and minimizes local flux distribution perturbations, minimizing potential problems due to transient local overheating of fuel. Analyzing heavy water effectiveness on neutronic parameters such as enrichment requirements, peaking factor and reactivity is important and should pay attention as primary concepts of a HWR core designing. Two nuclear nuclear reactors of CANDU-type and hexagonal-type reactor cores of 33 fuel assemblies and 19 assemblies in 1.04 P/D have been respectively simulated using MCNP-4C code. Using heavy water and light water as moderator have been compared for achieving less reactivity insertion and enrichment requirements. Two fuel matrixes of (232Th/235U)O2 and (238/235U)O2 have been compared to achieve more economical and safe design. Heavy water not only decreased enrichment needs, but it concluded in negative reactivity insertions during moderator density variations. Thorium oxide fuel assemblies of 2.3% enrichment loaded into the core of heavy water moderator resulted in 0.751 fission to absorption ratio and peaking factor of 1.7 using. Heavy water not only provides negative reactivity insertion during temperature raises which changes moderator density but concluded in 2 to 10 kg reduction of enrichment requirements, depend on geometry type.
Abstract: In many ways, biomedical analysis is analogous to possibilistic reasoning. In spite of that, there are hardly any applications of possibility theory in biology or medicine. The aim of this work is to demonstrate the use of possibility theory in an epidemiological study. In the paper, we build the possibility distribution for the controlled bloodstream concentrations of any physiologically active substance through few approximate considerations. This possibility distribution is tested later against the empirical histograms obtained from the panel study of the eight different physiologically active substances in 417 individuals.
Abstract: The most common forensic activity is searching a hard
disk for string of data. Nowadays, investigators and analysts are
increasingly experiencing large, even terabyte sized data sets when
conducting digital investigations. Therefore consecutive searching can
take weeks to complete successfully. There are two primary search
methods: index-based search and bitwise search. Index-based
searching is very fast after the initial indexing but initial indexing
takes a long time. In this paper, we discuss a high speed bitwise search
model for large-scale digital forensic investigations. We used pattern
matching board, which is generally used for network security, to
search for string and complex regular expressions. Our results indicate
that in many cases, the use of pattern matching board can substantially
increase the performance of digital forensic search tools.
Abstract: The success of an electronic system in a System-on- Chip is highly dependent on the efficiency of its interconnection network, which is constructed from routers and channels (the routers move data across the channels between nodes). Since neither classical bus based nor point to point architectures can provide scalable solutions and satisfy the tight power and performance requirements of future applications, the Network-on-Chip (NoC) approach has recently been proposed as a promising solution. Indeed, in contrast to the traditional solutions, the NoC approach can provide large bandwidth with moderate area overhead. The selected topology of the components interconnects plays prime rule in the performance of NoC architecture as well as routing and switching techniques that can be used. In this paper, we present two generic NoC architectures that can be customized to the specific communication needs of an application in order to reduce the area with minimal degradation of the latency of the system. An experimental study is performed to compare these structures with basic NoC topologies represented by 2D mesh, Butterfly-Fat Tree (BFT) and SPIN. It is shown that Cluster mesh (CMesh) and MinRoot schemes achieves significant improvements in network latency and energy consumption with only negligible area overhead and complexity over existing architectures. In fact, in the case of basic NoC topologies, CMesh and MinRoot schemes provides substantial savings in area as well, because they requires fewer routers. The simulation results show that CMesh and MinRoot networks outperforms MESH, BFT and SPIN in main performance metrics.
Abstract: This article discusses the problem of estimating the
orientation of inclined ground on which a human subject stands based
on information provided by the vestibular system consisting of the
otolith and semicircular canals. It is assumed that body segments are
not necessarily aligned and thus forming an open kinematic chain.
The semicircular canals analogues to a technical gyrometer provide a
measure of the angular velocity whereas the otolith analogues to a
technical accelerometer provide a measure of the translational
acceleration. Two solutions are proposed and discussed. The first is
based on a stand-alone Kalman filter that optimally fuses the two
measurements based on their dynamic characteristics and their noise
properties. In this case, no body dynamic model is needed. In the
second solution, a central extended disturbance observer that
incorporates a body dynamic model (internal model) is employed.
The merits of both solutions are discussed and demonstrated by
experimental and simulation results.
Abstract: Internet addiction has become a critical problem on
adolescents in Taiwan, and its negative effects on various dimensions
of adolescent development caught the attention of educational and
psychological experts. This study examined the correlation between
cognitive (locus of control) and emotion (emotion venting strategies)
factors on internet addiction of adolescents in Taiwan. Using the
Compulsive Internet Use (CIU) and the Emotion Venting Strategy
scales, a survey was conducted and 215 effective samples (students
ranging from12 to14 years old) returned. Quantitative analysis
methods such as descriptive statistics, t-test, ANOVA, Pearson
correlations and multiple regression were adopted. The results were as
follows: 1. Severity of Internet addiction has significant gender
differences; boys were at a higher risk than girls in becoming addicted
to the Internet. 2. Emotion venting, locus of control and internet
addiction have been shown to be positive correlated with one another.
3. Setting the locus of control as the control variable, emotion venting
strategy has positive and significant contribution to internet addiction.
The results of this study suggest that coaching deconstructive emotion
strategies and cognitive believes are encouraged to integrate with
actual field work.
Abstract: A Simultaneous Multithreading (SMT) Processor is
capable of executing instructions from multiple threads in the same
cycle. SMT in fact was introduced as a powerful architecture to
superscalar to increase the throughput of the processor.
Simultaneous Multithreading is a technique that permits multiple
instructions from multiple independent applications or threads to
compete limited resources each cycle. While the fetch unit has been
identified as one of the major bottlenecks of SMT architecture, several
fetch schemes were proposed by prior works to enhance the fetching
efficiency and overall performance.
In this paper, we propose a novel fetch policy called queue situation
identifier (QSI) which counts some kind of long latency instructions of
each thread each cycle then properly selects which threads to fetch
next cycle. Simulation results show that in best case our fetch policy
can achieve 30% on speedup and also can reduce the data cache level 1
miss rate.
Abstract: A simple network model is developed in OPNET to
study the performance of the Wi-Fi protocol. The model is simulated
in OPNET and performance factors such as load, throughput and delay
are analysed from the model. Four applications such as oracle, http, ftp
and voice are applied over the Wireless LAN network to determine the
throughput. The voice application utilises a considerable amount of
bandwidth of up to 5Mbps, as a result the 802.11g standard of the
Wi-Fi protocol was chosen which can support a data rate of up to
54Mbps. Results indicate that when the load in the Wi-Fi network is
increased the queuing delay on the point-to-point links in the Wi-Fi
network significantly reduces until it is comparable to that of WiMAX.
In conclusion, the queuing delay of the Wi-Fi protocol for the network
model simulated was about 0.00001secs comparable to WiMAX
network values.
Abstract: This paper contributes to our knowledge about buyerseller
relations by identifying barriers and conflict situations
associated with maintaining and developing durable business
relationships by small companies. The contribution of prior studies
with regard to negative aspects of marketing relationships is
presented in the first section. The international research results are
discussed with regard to the existing conceptualizations and main
research implications identified at the end.
Abstract: This paper presents the hardware design of a unified
architecture to compute the 4x4, 8x8 and 16x16 efficient twodimensional
(2-D) transform for the HEVC standard. This
architecture is based on fast integer transform algorithms. It is
designed only with adders and shifts in order to reduce the hardware
cost significantly. The goal is to ensure the maximum circuit reuse
during the computing while saving 40% for the number of operations.
The architecture is developed using FIFOs to compute the second
dimension. The proposed hardware was implemented in VHDL. The
VHDL RTL code works at 240 MHZ in an Altera Stratix III FPGA.
The number of cycles in this architecture varies from 33 in 4-point-
2D-DCT to 172 when the 16-point-2D-DCT is computed. Results
show frequency improvements reaching 96% when compared to an
architecture described as the direct transcription of the algorithm.
Abstract: This research proposes the state of art on how to control or find the trajectory paths of the RRP robot when the prismatic joint is malfunction. According to this situation, the minimum energy of the dynamic optimization is applied. The RRP robot or similar systems have been used in many areas such as fire fighter truck, laboratory equipment and military truck for example a rocket launcher. In order to keep on task that assigned, the trajectory paths must be computed. Here, the open loop control is applied and the result of an example show the reasonable solution which can be applied to the controllable system.
Abstract: Verapamil has been shown to inhibit fentanyl uptake in vitro and is a potent P-glycoprotein inhibitor. Tissue partitioning of loperamide, a commercially available opioid, is closely controlled by the P-gp efflux transporter. The following studies were designed to evaluate the effect of opioids on verapamil partitioning in the lung and brain, in vivo. Opioid (fentanyl or loperamide) was administered by intravenous infusion to Sprague Dawley rats alone or in combination with verapamil and plasma, with lung and brain tissues were collected at 1, 5, 6, 8, 10 and 60 minutes. Drug dispositions were modeled by recirculatory pharmacokinetic models. Fentanyl slightly increased the verapamil lung (PL) partition coefficient yet decreased the brain (PB) partition coefficient. Furthermore, loperamide significantly increased PLand PB. Fentanyl reduced the verapamil volume of distribution (V1) and verapamil elimination clearance (ClE). Fentanyl decreased verapamil brain partitioning, yet increased verapamil lung partitioning. Also, loperamide increased lung and brain partitioning in vivo. These results suggest that verapamil and fentanyl may be substrates of an unidentified inward transporter in brain tissue and confirm that verapamil and loperamide are substrates of the efflux transporter P-gp.
Abstract: Quantum cryptography offers a way of key agreement,
which is unbreakable by any external adversary. Authentication is
of crucial importance, as perfect secrecy is worthless if the identity
of the addressee cannot be ensured before sending important information.
Message authentication has been studied thoroughly, but no
approach seems to be able to explicitly counter meet-in-the-middle
impersonation attacks. The goal of this paper is the development of
an authentication scheme being resistant against active adversaries
controlling the communication channel. The scheme is built on top
of a key-establishment protocol and is unconditionally secure if built
upon quantum cryptographic key exchange. In general, the security
is the same as for the key-agreement protocol lying underneath.
Abstract: We present a numerical study of the sensitivity of the so called time relaxation family of models of fluid motion with respect to the time relaxation parameter χ on the two dimensional cavity problem. The goal of the study is to compute and compare the sensitivity of the model using finite difference method (FFD) and sensitivity equation method (SEM).
Abstract: An incentive for performance, as one subsystem of a
new performance management system, has been implemented in the
Thai public sector since 2004. This research investigates the
development of organizational justice in the incentive allocation by
comparing the roles of distributive and procedural justice on national
personnel-s attitudinal outcomes (incentive satisfaction and job
performance) between 2 periods, i.e. 2006 and 2008. The data were
collected via self-administered questionnaires completed by national
government officers and employees. They were stratified using multistage
sampling with 2,600 usable samples or 72.0% response rate in
2006, and 1,969 usable samples or 59.3% in 2008. The findings are:
(1) There is no difference in means between the two periods relating
to distributive justice, procedural justice, incentive satisfaction and
job performance. (2) Distributive justice and procedural justice
played more important roles in predicting incentive satisfaction and
job performance in 2008 than in 2006.
Abstract: In order to enhance the aircraft survivability, the
infrared signatures emitted by hot engine parts should be determined
exactly. For its reduction it is necessary for the rear fuselage
temperature to be decreased. In this study, numerical modeling of flow
fields and heat transfer characteristics of an aircraft nozzle is
performed and its temperature distribution along each component wall
is predicted. The radiation shield is expected to reduce the skin
temperature of rear fuselage. The effect of material characteristic of
radiation shield on the heat transfer is also investigated. Through this
numerical analysis, design parameters related to the susceptibility of
aircraft are examined.