Abstract: The controllable electrical loss which consists of the
copper loss and iron loss can be minimized by the optimal control of
the armature current vector. The control algorithm of current vector
minimizing the electrical loss is proposed and the optimal current
vector can be decided according to the operating speed and the load
conditions. The proposed control algorithm is applied to the
experimental PM motor drive system and this paper presents a
modern approach of speed control for permanent magnet
synchronous motor (PMSM) applied for Electric Vehicle using a
nonlinear control. The regulation algorithms are based on the
feedback linearization technique. The direct component of the current
is controlled to be zero which insures the maximum torque operation.
The near unity power factor operation is also achieved. More over,
among EV-s motor electric propulsion features, the energy efficiency
is a basic characteristic that is influenced by vehicle dynamics and
system architecture. For this reason, the EV dynamics are taken into
account.
Abstract: The proper selection of the AC-side passive filter
interconnecting the voltage source converter to the power supply is
essential to obtain satisfactory performances of an active power filter
system. The use of the LCL-type filter has the advantage of
eliminating the high frequency switching harmonics in the current
injected into the power supply. This paper is mainly focused on
analyzing the influence of the interface filter parameters on the active
filtering performances. Some design aspects are pointed out. Thus,
the design of the AC interface filter starts from transfer functions by
imposing the filter performance which refers to the significant current
attenuation of the switching harmonics without affecting the
harmonics to be compensated. A Matlab/Simulink model of the entire
active filtering system including a concrete nonlinear load has been
developed to examine the system performances. It is shown that a
gamma LC filter could accomplish the attenuation requirement of the
current provided by converter. Moreover, the existence of an optimal
value of the grid-side inductance which minimizes the total harmonic
distortion factor of the power supply current is pointed out.
Nevertheless, a small converter-side inductance and a damping
resistance in series with the filter capacitance are absolutely needed
in order to keep the ripple and oscillations of the current at the
converter side within acceptable limits. The effect of change in the
LCL-filter parameters is evaluated. It is concluded that good active
filtering performances can be achieved with small values of the
capacitance and converter-side inductance.
Abstract: This paper presents the influence of preloading on a)
the contact tractions, b) slip levels and c) stresses at the dovetail
blade-disc interface of an aero-engine through a three-dimensional
(3D) finite element (FE) modeling and analysis. The preloading is
applied by an interference fit at the dovetail interface and the bulk
loading is applied through the rotational speed of rotor. Preloading at
the dovetail interface reduces the peak contact pressure developed
due to bulk loading up to 35%, and reduces the peak contact pressure
and stress difference between top and bottom contact edges.
Increasing the level of preloading reduces the cyclic stress amplitude
at the interface up to certain values of preload and as a consequence,
an improvement in fatigue life could be expected. Fretting damage,
due to vibration and wind milling effect during engine ground
condition, can be minimized by preloading the dovetail interface.
Abstract: The need of high frame-rate imaging has been triggered by the new applications of ultrasound imaging to transient elastography and real-time 3D ultrasound. Using plane wave excitation (PWE) is one of the methods to achieve very high frame-rate imaging since an image can be formed with a single insonification. However, due to the lack of transmit focusing, the image quality with PWE is lower compared with those using conventional focused transmission. To solve this problem, we propose a filter-retrieved transmit focusing (FRF) technique combined with cross-correlation weighting (FRF+CC weighting) for high frame-rate imaging with PWE. A restrospective focusing filter is designed to simultaneously minimize the predefined sidelobe energy associated with single PWE and the filter energy related to the signal-to-noise-ratio (SNR). This filter attempts to maintain the mainlobe signals and to reduce the sidelobe ones, which gives similar mainlobe signals and different sidelobes between the original PWE and the FRF baseband data. Normalized cross-correlation coefficient at zero lag is calculated to quantify the degree of similarity at each imaging point and used as a weighting matrix to the FRF baseband data to further suppress sidelobes, thus improving the filter-retrieved focusing quality.
Abstract: Optimal routing in communication networks is a
major issue to be solved. In this paper, the application of Tabu Search
(TS) in the optimum routing problem where the aim is to minimize
the computational time and improvement of quality of the solution in
the communication have been addressed. The goal is to minimize the
average delays in the communication. The effectiveness of Tabu
Search method is shown by the results of simulation to solve the
shortest path problem. Through this approach computational cost can
be reduced.
Abstract: In textile industry, besides the conventional textile
products, technical textile goods, that have been brought external
functional properties into, are being developed for technical textile
industry. Especially these products produced with weaving
technology are widely preferred in areas such as sports, geology,
medical, automotive, construction and marine sectors. These textile
products are exposed to various stresses and large deformations under
typical conditions of use. At this point, sufficient and reliable data
could not be obtained with uniaxial tensile tests for determination of
the mechanical properties of such products due to mainly biaxial
stress state. Therefore, the most preferred method is a biaxial tensile
test method and analysis. These tests and analysis is applied to fabrics
with different functional features in order to establish the textile
material with several characteristics and mechanical properties of the
product. Planar biaxial tensile test, cylindrical inflation and bulge
tests are generally required to apply for textile products that are used
in automotive, sailing and sports areas and construction industry to
minimize accidents as long as their service life. Airbags, seat belts
and car tires in the automotive sector are also subject to the same
biaxial stress states, and can be characterized by same types of
experiments. In this study, in accordance with the research literature
related to the various biaxial test methods are compared. Results with
discussions are elaborated mainly focusing on the design of a biaxial
test apparatus to obtain applicable experimental data for developing a
finite element model. Sample experimental results on a prototype
system are expressed.
Abstract: In the modern manufacturing systems, the use of
thermal cutting techniques using oxyfuel, plasma and laser have
become indispensable for the shape forming of high quality complex
components; however, the conventional chip removal production
techniques still have its widespread space in the manufacturing
industry. Both these types of machining operations require the
positioning of end effector tool at the edge where the cutting process
commences. This repositioning of the cutting tool in every machining
operation is repeated several times and is termed as non-productive
time or airtime motion. Minimization of this non-productive
machining time plays an important role in mass production with high
speed machining. As, the tool moves from one region to the other by
rapid movement and visits a meticulous region once in the whole
operation, hence the non-productive time can be minimized by
synchronizing the tool movements. In this work, this problem is
being formulated as a general travelling salesman problem (TSP) and
a genetic algorithm approach has been applied to solve the same. For
improving the efficiency of the algorithm, the GA has been
hybridized with a noble special heuristic and simulating annealing
(SA). In the present work a novel heuristic in the combination of GA
has been developed for synchronization of toolpath movements
during repositioning of the tool. A comparative analysis of new Meta
heuristic techniques with simple genetic algorithm has been
performed. The proposed metaheuristic approach shows better
performance than simple genetic algorithm for minimization of nonproductive
toolpath length. Also, the results obtained with the help of
hybrid simulated annealing genetic algorithm (HSAGA) are also
found better than the results using simple genetic algorithm only.
Abstract: Transmission network expansion planning (TNEP) is an important component of power system planning that its task is to minimize the network construction and operational cost while satisfying the demand increasing, imposed technical and economic conditions. Up till now, various methods have been presented to solve the static transmission network expansion planning (STNEP) problem. But in all of these methods, the lines adequacy rate has not been studied after the planning horizon, i.e. when the expanded network misses its adequacy and needs to be expanded again. In this paper, in order to take transmission lines condition after expansion in to account from the line loading view point, the adequacy of transmission network is considered for solution of STNEP problem. To obtain optimal network arrangement, a decimal codification genetic algorithm (DCGA) is being used for minimizing the network construction and operational cost. The effectiveness of the proposed idea is tested on the Garver's six-bus network. The results evaluation reveals that the annual worth of network adequacy has a considerable effect on the network arrangement. In addition, the obtained network, based on the DCGA, has lower investment cost and higher adequacy rate. Thus, the network satisfies the requirements of delivering electric power more safely and reliably to load centers.
Abstract: Most electrical distribution systems are incurring large
losses as the loads are wide spread, inadequate reactive power
compensation facilities and their improper control. A typical static
VAR compensator consists of capacitor bank in binary sequential
steps operated in conjunction with a thyristor controlled reactor of the
smallest step size. This SVC facilitates stepless control of reactive
power closely matching with load requirements so as to maintain
power factor nearer to unity. This type of SVC-s requiring a
appropriately controlled TCR. This paper deals with an air cored
reactor suitable for distribution transformer of 3phase, 50Hz, Dy11,
11KV/433V, 125 KVA capacity. Air cored reactors are designed,
built, tested and operated in conjunction with capacitor bank in five
binary sequential steps. It is established how the delta connected TCR
minimizes the harmonic components and the operating range for
various electrical quantities as a function of firing angle is
investigated. In particular firing angle v/s line & phase currents, D.C.
components, THD-s, active and reactive powers, odd and even triplen
harmonics, dominant characteristic harmonics are all investigated and
range of firing angle is fixed for satisfactory operation. The harmonic
spectra for phase and line quantities at specified firing angles are
given. In case the TCR is operated within the bound specified in this
paper established through simulation studies are yielding the best
possible operating condition particularly free from all dominant
harmonics.
Abstract: A manufacturing inventory model with shortages with
carrying cost, shortage cost, setup cost and demand quantity as
imprecise numbers, instead of real numbers, namely interval number
is considered here. First, a brief survey of the existing works on
comparing and ranking any two interval numbers on the real line
is presented. A common algorithm for the optimum production
quantity (Economic lot-size) per cycle of a single product (so as
to minimize the total average cost) is developed which works well
on interval number optimization under consideration. Finally, the
designed algorithm is illustrated with numerical example.
Abstract: A large quantity of world-s oil reserves exists in
carbonate reservoirs. Carbonate reservoirs are very sensitive to
chemical enhanced oil recovery process because of containing large
amount of calcite, dolomite and calcium sulfate minerals. These
minerals cause major obstacles during alkali-surfactant-polymer
(ASP) flooding. Alkali reacts with these minerals and form undesired
precipitations which plug effective porous openings, reduce
permeability and cause scale occurrence at the wellbore. In this
paper, a new chemical combination consists of acrylic acid and alkali
was used to minimize precipitation problem during ASP flooding. A
series of fluid-fluid compatibility tests were performed using acrylic
acid and different concentrations of alkaline. Two types of alkalis
namely; sodium carbonate and sodium metaborate were screened. As
a result, the combination of acrylic acid and sodium carbonate was
not effective in preventing calcium and magnesium precipitations.
However, acrylic acid and sodium metaborate showed promising
results for keeping all solutions without any precipitations. The ratio
of acrylic acid to sodium metaborate of 0.7:1.0 was found to be
optimum for achieving a compatible solution for 30 days at 80oC.
Abstract: Air pollution is a major environmental health
problem, affecting developed and developing countries around the
world. Increasing amounts of potentially harmful gases and
particulate matter are being emitted into the atmosphere on a global
scale, resulting in damage to human health and the environment.
Petroleum-related air pollutants can have a wide variety of adverse
environmental impacts. In the crude oil production sectors, there is a
strong need for a thorough knowledge of gaseous emissions resulting
from the flaring of associated gas of known composition on daily
basis through combustion activities under several operating
conditions. This can help in the control of gaseous emission from
flares and thus in the protection of their immediate and distant
surrounding against environmental degradation.
The impacts of methane and non-methane hydrocarbons emissions
from flaring activities at oil production facilities at Kuwait Oilfields
have been assessed through a screening study using records of flaring
operations taken at the gas and oil production sites, and by analyzing
available meteorological and air quality data measured at stations
located near anthropogenic sources. In the present study the
Industrial Source Complex (ISCST3) Dispersion Model is used to
calculate the ground level concentrations of methane and nonmethane
hydrocarbons emitted due to flaring in all over Kuwait
Oilfields.
The simulation of real hourly air quality in and around oil
production facilities in the State of Kuwait for the year 2006,
inserting the respective source emission data into the ISCST3
software indicates that the levels of non-methane hydrocarbons from
the flaring activities exceed the allowable ambient air standard set by
Kuwait EPA. So, there is a strong need to address this acute problem
to minimize the impact of methane and non-methane hydrocarbons
released from flaring activities over the urban area of Kuwait.
Abstract: This study compares three meta heuristics to minimize makespan (Cmax) for Hybrid Flow Shop (HFS) Scheduling Problem with Parallel Machines. This problem is known to be NP-Hard. This study proposes three algorithms among improvement heuristic searches which are: Genetic Algorithm (GA), Simulated Annealing (SA), and Tabu Search (TS). SA and TS are known as deterministic improvement heuristic search. GA is known as stochastic improvement heuristic search. A comprehensive comparison from these three improvement heuristic searches is presented. The results for the experiments conducted show that TS is effective and efficient to solve HFS scheduling problems.
Abstract: This paper presents modeling and optimization of two NP-hard problems in flexible manufacturing system (FMS), part type selection problem and loading problem. Due to the complexity and extent of the problems, the paper was split into two parts. The first part of the papers has discussed the modeling of the problems and showed how the real coded genetic algorithms (RCGA) can be applied to solve the problems. This second part discusses the effectiveness of the RCGA which uses an array of real numbers as chromosome representation. The novel proposed chromosome representation produces only feasible solutions which minimize a computational time needed by GA to push its population toward feasible search space or repair infeasible chromosomes. The proposed RCGA improves the FMS performance by considering two objectives, maximizing system throughput and maintaining the balance of the system (minimizing system unbalance). The resulted objective values are compared to the optimum values produced by branch-and-bound method. The experiments show that the proposed RCGA could reach near optimum solutions in a reasonable amount of time.
Abstract: A data cutting and sorting method (DCSM) is proposed
to optimize the performance of data mining. DCSM reduces the
calculation time by getting rid of redundant data during the data
mining process. In addition, DCSM minimizes the computational units
by splitting the database and by sorting data with support counts. In the
process of searching for the relationship between metabolic syndrome
and lifestyles with the health examination database of an electronics
manufacturing company, DCSM demonstrates higher search
efficiency than the traditional Apriori algorithm in tests with different
support counts.
Abstract: In this paper, we present a comparative study between two computer vision systems for objects recognition and tracking, these algorithms describe two different approach based on regions constituted by a set of pixels which parameterized objects in shot sequences. For the image segmentation and objects detection, the FCM technique is used, the overlapping between cluster's distribution is minimized by the use of suitable color space (other that the RGB one). The first technique takes into account a priori probabilities governing the computation of various clusters to track objects. A Parzen kernel method is described and allows identifying the players in each frame, we also show the importance of standard deviation value research of the Gaussian probability density function. Region matching is carried out by an algorithm that operates on the Mahalanobis distance between region descriptors in two subsequent frames and uses singular value decomposition to compute a set of correspondences satisfying both the principle of proximity and the principle of exclusion.
Abstract: This paper discusses the landscape design that could
increase energy efficiency in a house. By planting trees in a house
compound, the tree shades prevent direct sunlight from heating up
the building, and it enables cooling off the surrounding air. The
requirement for air-conditioning could be minimized and the air
quality could be improved. During the life time of a tree, the saving
cost from the mentioned benefits could be up to US $ 200 for each
tree. The project intends to visually describe the landscape design in
a house compound that could enhance energy efficiency and
consequently lead to energy saving. The house compound model was
developed in three dimensions by using AutoCAD 2005, the
animation was programmed by using LightWave 3D softwares i.e.
Modeler and Layout to display the tree shadings in the wall. The
visualization was executed on a VRML Pad platform and
implemented on a web environment.
Abstract: In this paper, we consider the problem of logic simplification for a special class of logic functions, namely complementary Boolean functions (CBF), targeting low power implementation using static CMOS logic style. The functions are uniquely characterized by the presence of terms, where for a canonical binary 2-tuple, D(mj) ∪ D(mk) = { } and therefore, we have | D(mj) ∪ D(mk) | = 0 [19]. Similarly, D(Mj) ∪ D(Mk) = { } and hence | D(Mj) ∪ D(Mk) | = 0. Here, 'mk' and 'Mk' represent a minterm and maxterm respectively. We compare the circuits minimized with our proposed method with those corresponding to factored Reed-Muller (f-RM) form, factored Pseudo Kronecker Reed-Muller (f-PKRM) form, and factored Generalized Reed-Muller (f-GRM) form. We have opted for algebraic factorization of the Reed-Muller (RM) form and its different variants, using the factorization rules of [1], as it is simple and requires much less CPU execution time compared to Boolean factorization operations. This technique has enabled us to greatly reduce the literal count as well as the gate count needed for such RM realizations, which are generally prone to consuming more cells and subsequently more power consumption. However, this leads to a drawback in terms of the design-for-test attribute associated with the various RM forms. Though we still preserve the definition of those forms viz. realizing such functionality with only select types of logic gates (AND gate and XOR gate), the structural integrity of the logic levels is not preserved. This would consequently alter the testability properties of such circuits i.e. it may increase/decrease/maintain the same number of test input vectors needed for their exhaustive testability, subsequently affecting their generalized test vector computation. We do not consider the issue of design-for-testability here, but, instead focus on the power consumption of the final logic implementation, after realization with a conventional CMOS process technology (0.35 micron TSMC process). The quality of the resulting circuits evaluated on the basis of an established cost metric viz., power consumption, demonstrate average savings by 26.79% for the samples considered in this work, besides reduction in number of gates and input literals by 39.66% and 12.98% respectively, in comparison with other factored RM forms.
Abstract: Differentiated impact of team sports (basketball, indoor soccer, handball) on general haemodynamics and aerobic potential of students who specialize in technical subjects is detected only on the fourth year of studies in the institute of higher education. Those who play basketball and indoor soccer have shown increase of stroke and minute volume of blood indices, pumping and contractile function of the heart, oxygenation of blood and oxygen delivery to tissues, aerobic energy supply and balance of sympathetic and parasympathetic activity of the nervous regulation mechanism of the circulatory system. Those who play handball have shown these indices statistically decreased. On the whole playing basketball and indoor soccer optimizes the strategy for adaptation of students to the studying process, but playing handball does the opposite thing. The leading factor for adaptation of students is: those who play basketball have increase of minute blood volume which stipulates velocity of the system blood circulation and well-timed oxygen delivery to tissues; those who play indoor soccer have increase of power and velocity of contractile function of the heart; those who play handball have increase of resistance of thorax to the system blood flow which minimizes contractile function of the heart, blood oxygen saturation and delivery of oxygen to tissues.
Abstract: A scalable QoS aware multicast deployment in
DiffServ networks has become an important research dimension in
recent years. Although multicasting and differentiated services are
two complementary technologies, the integration of the two
technologies is a non-trivial task due to architectural conflicts
between them. A popular solution proposed is to extend the
functionality of the DiffServ components to support multicasting. In
this paper, we propose an algorithm to construct an efficient QoSdriven
multicast tree, taking into account the available bandwidth per
service class. We also present an efficient way to provision the
limited available bandwidth for supporting heterogeneous users. The
proposed mechanism is evaluated using simulated tests. The
simulated result reveals that our algorithm can effectively minimize
the bandwidth use and transmission cost