Abstract: For several hundred years, the design of railway tracks
has practically remained unchanged. Traditionally, rail tracks are
placed on a ballast layer due to several reasons, including economy,
rapid drainage, and high load bearing capacity. The primary function
of ballast is to distributing dynamic track loads to sub-ballast and
subgrade layers, while also providing lateral resistance and allowing
for rapid drainage. Upon repeated trainloads, the ballast becomes
fouled due to ballast degradation and the intrusion of fines which
adversely affects the strength and deformation behaviour of ballast.
This paper presents the use of three-dimensional discrete element
method (DEM) in studying the shear behaviour of the fouled ballast
subjected to direct shear loading. Irregularly shaped particles of
ballast were modelled by grouping many spherical balls together in
appropriate sizes to simulate representative ballast aggregates. Fouled
ballast was modelled by injecting a specified number of miniature
spherical particles into the void spaces. The DEM simulation
highlights that the peak shear stress of the ballast assembly decreases
and the dilation of fouled ballast increases with an increase level of
fouling. Additionally, the distributions of contact force chain and
particle displacement vectors were captured during shearing progress,
explaining the formation of shear band and the evolutions of
volumetric change of fouled ballast.
Abstract: Microstructure and mechanical properties of AZ91D
Mg alloys for nonflammable use, containing Ca and Y, were
investigated in this study. Solid solution treatment of AZ91D Mg alloy
with Ca and Y was successfully conducted at 420oC and
supersaturated microstructure with almost all beta phases resolved into
matrix was obtained. After solid solution treatment, the alloy was
annealed at temperatures of 180 and 200oC for time intervals from 1
min to 48 hrs and hardness of each condition was measured by
micro-Vickers method. Peak aging conditions were deduced from the
results as at the temperature of 200oC for 10 hrs. Hot rolling was also
carried out at 400oC by the reduction ratio of 0.6 through 5 passes
followed by recrystallization treatment. Tensile and compressive
properties were measured at room temperature on the specimens of
each process, i.e. as-cast, solution treatment, hot rolling, and
recrystallization.
Abstract: The aim of irrigation is to recharge the available water
in the soil. Quality of irrigation water is essential for the yield and
quality of crops produced, maintenance of soil productivity and
protection of the environment. The analysis of irrigation water arises
as a need to know the impact of irrigation water on the yield of crops,
the effect, and the necessary control measures to rectify the effect of
this for optimum production and yield of crops. This study was conducted to assess the quality of irrigation water
with its performance on crop planted, in Josepdam irrigation scheme
Bacita, Nigeria. Field visits were undertaken to identify and locate
water supply sources and collect water samples from these sources;
X1 Drain, Oshin, River Niger loop and Ndafa. Laboratory
experiments were then undertaken to determine the quality of raw
water from these sources. The analysis was carried for various parameters namely; physical
and chemical analyses after water samples have been taken from four
sources. The samples were tested in laboratory. Results showed that
the raw water sources shows no salinity tendencies with SAR values
less than 1me/l and Ecvaules at Zero while the pH were within the
recommended range by FAO, there are increase in potassium and
sulphate content contamination in three of the location. From this, it
is recommended that there should be proper monitoring of the
scheme by conducting analysis of water and soil in the environment,
preferable test should be carried out at least one year to cover the
impact of seasonal variations and to determine the physical and
chemical analysis of the water used for irrigation at the scheme.
Abstract: This paper describes an ab-initio design, development and calibration results of an Optical Sensor Ground Reaction Force Measurement Platform (OSGRFP) for gait and geriatric studies. The developed system employs an array of FBG sensors to measure the respective ground reaction forces from all three axes (X, Y and Z), which are perpendicular to each other. The novelty of this work is two folded. One is in its uniqueness to resolve the tri axial resultant forces during the stance in to the respective pure axis loads and the other is the applicability of inherently advantageous FBG sensors which are most suitable for biomechanical instrumentation. To validate the response of the FBG sensors installed in OSGRFP and to measure the cross sensitivity of the force applied in other directions, load sensors with indicators are used. Further in this work, relevant mathematical formulations are presented for extracting respective ground reaction forces from wavelength shifts/strain of FBG sensors on the OSGRFP. The result of this device has implications in understanding the foot function, identifying issues in gait cycle and measuring discrepancies between left and right foot. The device also provides a method to quantify and compare relative postural stability of different subjects under test, which has implications in post-surgical rehabilitation, geriatrics and optimizing training protocols for sports personnel.
Abstract: With the strengthened regulation on the mandatory use
of recycled aggregate, development of construction materials using
recycled aggregate has recently increased. This study aimed to secure
the performance of asphalt concrete mixture by developing
recycled-modified asphalt using recycled basalt aggregate from the
Jeju area. The strength of the basalt aggregate from the Jeju area used
in this study was similar to that of general aggregate, while the specific
surface area was larger due to the development of pores. Modified
asphalt was developed using a general aggregate-recycled aggregate
ratio of 7:3, and the results indicated that the Marshall stability
increased by 27% compared to that of asphalt concrete mixture using
only general aggregate, and the flow values showed similar levels.
Also, the indirect tensile strength increased by 79%, and the toughness
increased by more than 100%. In addition, the TSR for examining
moisture resistance was 0.95 indicating that the reduction in the
indirect tensile strength due to moisture was very low (5% level), and
the developed recycled-modified asphalt could satisfy all the quality
standards of asphalt concrete mixture.
Abstract: In the deep south of Thailand, checkpoints for people
verification are necessary for the security management of risk zones,
such as official buildings in the conflict area. In this paper, we
propose an automatic checkpoint system that verifies persons using
information from ID cards and facial features. The methods for a
person’s information abstraction and verification are introduced
based on useful information such as ID number and name, extracted
from official cards, and facial images from videos. The proposed
system shows promising results and has a real impact on the local
society.
Abstract: Torrefaction of biomass pellets is considered as a
useful pretreatment technology in order to convert them into a high
quality solid biofuel that is more suitable for pyrolysis, gasification,
combustion, and co-firing applications. In the course of torrefaction,
the temperature varies across the pellet, and therefore chemical
reactions proceed unevenly within the pellet. However, the
uniformity of the thermal distribution along the pellet is generally
assumed. The torrefaction process of a single cylindrical pellet is
modeled here, accounting for heat transfer coupled with chemical
kinetics. The drying sub-model was also introduced. The nonstationary
process of wood pellet decomposition is described by the
system of non-linear partial differential equations over the
temperature and mass. The model captures well the main features of
the experimental data.
Abstract: Medicinal and aromatic plants are promising and are characterized by the biosynthesis of odorous molecules that make up the so-called essential oils (EO), which have long been known for their antiseptic and therapeutic activity in folk medicine. Essential oils have many therapeutic properties. In herbal medicine, they are used for their antiseptic properties against infectious diseases of fungal origin, against dermatophytes, those of bacterial origin. The objective of this study was to evaluate the influence of drying in the shade on the water content and on the content of essential oils extracted from leaves of Eucalyptus camendulensis for better quality control of medicinal and aromatic plants. The water content of the Eucalyptus camendulensis plant material decreases during the drying process. It decreased from 100% to 0.006% for the drying in the shade after ten days. The moisture content is practically constant at the end of the drying period. The drying in the shade increases the concentration of essential oils of Eucalyptus camendulensis. When the leaves of Eucalyptus camendulensis plant are in the shade, the maximum of the essential oil content was obtained on the eighth day, the recorded value was 1.43% ± 0.01%. Beyond these periods, the content continuously drop in before stabilizing. The optimum drying time is between 6 and 9 days.
Abstract: This paper proposes a method of learning topics for
broadcasting contents. There are two kinds of texts related to
broadcasting contents. One is a broadcasting script, which is a series of
texts including directions and dialogues. The other is blogposts, which
possesses relatively abstracted contents, stories, and diverse
information of broadcasting contents. Although two texts range over
similar broadcasting contents, words in blogposts and broadcasting
script are different. When unseen words appear, it needs a method to
reflect to existing topic. In this paper, we introduce a semantic
vocabulary expansion method to reflect unseen words. We expand
topics of the broadcasting script by incorporating the words in
blogposts. Each word in blogposts is added to the most semantically
correlated topics. We use word2vec to get the semantic correlation
between words in blogposts and topics of scripts. The vocabularies of
topics are updated and then posterior inference is performed to
rearrange the topics. In experiments, we verified that the proposed
method can discover more salient topics for broadcasting contents.
Abstract: Some of the main causes for degradation of polymeric materials are thermal aging, hydrolysis, oxidation or chemical degradation by acids, alkalis or water. The first part of this paper provides a brief summary of advances in technology, methods and specification of composite materials for relining as a rehabilitation technique for sewage systems. The second part summarizes an investigation on frequently used composite materials for relining in Sweden, the rubber filled epoxy composite and reinforced polyester composite when they were immersed in deionized water or in dry conditions, and elevated temperatures up to 80°C in the laboratory. The tests were conducted by visual inspection, microscopy, Dynamic Mechanical Analysis (DMA), Differential Scanning Calorimetry (DSC) as well as mechanical testing, three point bending and tensile testing.
Abstract: Motion response of floating structures is of great
concern in marine engineering. Nonlinearity is an inherent property
of any floating bodies subjected to irregular waves. These floating
structures are continuously subjected to environmental loadings from
wave, current, wind etc. This can result in undesirable motions of the
vessel which may challenge the operability. For a floating body to
remain in its position, it should be able to induce a restoring force
when displaced. Mooring is provided to enable this restoring force.
This paper discusses the hydrodynamic performance and motion
characteristics of an 8 point spread mooring system applied to a pipe
laying barge operating in the West African sea. The modelling of the
barge is done using a computer aided-design (CAD) software
RHINOCEROS. Irregular waves are generated using a suitable wave
spectrum. Both frequency domain and time domain analysis is done.
Numerical simulations based on potential theory are carried out to
find the responses and hydrodynamic performance of the barge in
both free floating as well as moored conditions. Initially, potential
flow frequency domain analysis is done to obtain the Response
Amplitude Operator (RAO) which gives an idea about the structural
motion in free floating state. RAOs for different wave headings are
analyzed. In the following step, a time domain analysis is carried out
to obtain the responses of the structure in the moored condition. In
this study, wave induced motions are only taken into consideration.
Wind and current loads are ruled out and shall be included in further
studies. For the current study, 2000 seconds simulation is taken. The
results represent wave induced motion responses, mooring line
tensions and identify critical mooring lines.
Abstract: We have aimed to produce a self-cleaning transparent
polymer coating with polyurethane (PU) matrix as the latter is highly
solvent, chemical and weather resistant having good mechanical
properties. Nano-silica modified by 1H, 1H, 2H, 2Hperflurooctyltriethoxysilane
was incorporated into the PU matrix for
attaining self-cleaning ability through hydrophobicity. The
modification was confirmed by particle size analysis and scanning
electron microscopy (SEM). Thermo-gravimetric (TGA) studies were
carried to ascertain the grafting of silane onto the silica. Several
coating formulations were prepared by varying the silica loading
content and compared to a commercial equivalent. The effect of
dispersion and the morphology of the coated films were assessed by
SEM analysis. All coating standardized tests like solvent resistance,
adhesion, flexibility, acid, alkali, gloss etc. have been performed as
per ASTM standards. Water contact angle studies were conducted to
analyze the hydrophobic character of the coating. In addition, the
coatings were also subjected to salt spray and accelerated weather
testing to analyze the durability of the coating.
Abstract: Landfill waste is a common problem as it has an
economic and environmental impact even if it is closed. Landfill
waste contains a high density of various persistent compounds such
as heavy metals, organic and inorganic materials. As persistent
compounds are slowly-degradable or even non-degradable in the
environment, they often produce sublethal or even lethal effects on
aquatic organisms. The aims of the present study were to estimate
sublethal effects of the Kairiai landfill (WGS: 55°55‘46.74“,
23°23‘28.4“) leachate on the locomotor activity of rainbow trout
Oncorhynchus mykiss juveniles using the original system package
developed in our laboratory for automated monitoring, recording and
analysis of aquatic organisms’ activity, and to determine patterns of
fish behavioral response to sublethal effects of leachate. Four
different concentrations of leachate were chosen: 0.125; 0.25; 0.5 and
1.0 mL/L (0.0025; 0.005; 0.01 and 0.002 as part of 96-hour LC50,
respectively). Locomotor activity was measured after 5, 10 and 30
minutes of exposure during 1-minute test-periods of each fish (7 fish
per treatment). The threshold-effect-concentration amounted to 0.18
mL/L (0.0036 parts of 96-hour LC50). This concentration was found
to be even 2.8-fold lower than the concentration generally assumed to
be “safe” for fish. At higher concentrations, the landfill leachate
solution elicited behavioral response of test fish to sublethal levels of
pollutants. The ability of the rainbow trout to detect and avoid
contaminants occurred after 5 minutes of exposure. The intensity of
locomotor activity reached a peak within 10 minutes, evidently
decreasing after 30 minutes. This could be explained by the
physiological and biochemical adaptation of fish to altered
environmental conditions. It has been established that the locomotor
activity of juvenile trout depends on leachate concentration and
exposure duration. Modeling of these parameters showed that the
activity of juveniles increased at higher leachate concentrations, but
slightly decreased with the increasing exposure duration. Experiment
results confirm that the behavior of rainbow trout juveniles is a
sensitive and rapid biomarker that can be used in combination with
the system for fish behavior monitoring, registration and analysis to
determine sublethal concentrations of pollutants in ambient water.
Further research should be focused on software improvement aimed
to include more parameters of aquatic organisms’ behavior and to
investigate the most rapid and appropriate behavioral responses in
different species. In practice, this study could be the basis for the
development and creation of biological early-warning systems
(BEWS).
Abstract: At the Savonia University of Applied Sciences (UAS),
curriculum and studies have been improved by applying an Open
Innovation Space approach (OIS). It is based on multidisciplinary
action learning. The key elements of OIS-ideology are work-life
orientation, and student-centric communal learning. In this approach,
every participant can learn from each other and innovations will be
created. In this social innovation educational approach, all practices
are carried out in close collaboration with enterprises in real-life
settings, not in classrooms. As an example, in this paper, Savonia
UAS’s Future Food RDI hub (FF) shows how OIS practices are
implemented by providing food product development and consumer
research services for enterprises in close collaboration with
academicians, students and consumers. In particular one example of
OIS experimentation in the field is provided by a consumer research
carried out utilizing verbal analysis protocol combined with audiovisual
observation (VAP-WAVO). In this case, all co-learners were
acting together in supermarket settings to collect the relevant data for
a product development and the marketing department of a company.
The company benefitted from the results obtained, students were
more satisfied with their studies, educators and academicians were
able to obtain good evidence for further collaboration as well as
renewing curriculum contents based on the requirements of working
life. In addition, society will benefit over time as young university
adults find careers more easily through their OIS related food science
studies. Also this knowledge interaction model re-news education
practices and brings working-life closer to educational research
institutes.
Abstract: Fractal based digital image compression is a specific
technique in the field of color image. The method is best suited for
irregular shape of image like snow bobs, clouds, flame of fire; tree
leaves images, depending on the fact that parts of an image often
resemble with other parts of the same image. This technique has
drawn much attention in recent years because of very high
compression ratio that can be achieved. Hybrid scheme incorporating
fractal compression and speedup techniques have achieved high
compression ratio compared to pure fractal compression. Fractal
image compression is a lossy compression method in which selfsimilarity
nature of an image is used. This technique provides high
compression ratio, less encoding time and fart decoding process. In
this paper, fractal compression with quad tree and DCT is proposed
to compress the color image. The proposed hybrid schemes require
four phases to compress the color image. First: the image is
segmented and Discrete Cosine Transform is applied to each block of
the segmented image. Second: the block values are scanned in a
zigzag manner to prevent zero co-efficient. Third: the resulting image
is partitioned as fractals by quadtree approach. Fourth: the image is
compressed using Run length encoding technique.
Abstract: Myoelectric control system is the fundamental
component of modern prostheses, which uses the myoelectric signals
from an individual’s muscles to control the prosthesis movements.
The surface electromyogram signal (sEMG) being noninvasive has
been used as an input to prostheses controllers for many years.
Recent technological advances has led to the development of
implantable myoelectric sensors which enable the internal
myoelectric signal (MES) to be used as input to these prostheses
controllers. The intramuscular measurement can provide focal
recordings from deep muscles of the forearm and independent signals
relatively free of crosstalk thus allowing for more independent
control sites. However, little work has been done to compare the two
inputs. In this paper we have compared the classification accuracy of
six pattern recognition based myoelectric controllers which use
surface myoelectric signals recorded using untargeted (symmetric)
surface electrode arrays to the same controllers with multichannel
intramuscular myolectric signals from targeted intramuscular
electrodes as inputs. There was no significant enhancement in the
classification accuracy as a result of using the intramuscular EMG
measurement technique when compared to the results acquired using
the surface EMG measurement technique. Impressive classification
accuracy (99%) could be achieved by optimally selecting only five
channels of surface EMG.
Abstract: The purpose of the research described in this work is
to answer how to measure the rheologic (viscoelastic) properties
tendo–deformational characteristics of soft tissue. The method would
also resemble muscle palpation examination as it is known in clinical
practice. For this purpose, an instrument with the working name
“myotonometer” has been used. At present, there is lack of objective methods for assessing the
muscle tone by viscous and elastic properties of soft tissue. That is
why we decided to focus on creating or finding quantitative and
qualitative methodology capable to specify muscle tone.
Abstract: The rheological response of blends obtained from
quaternized polysulfone and polyvinyl alcohol in N-methyl-2-
pyrrolidone as against structural peculiarity of polymers from the
blend, composition of polymer mixtures, as well as the types of
interactions were investigated. Results show that the variation of
polyvinyl alcohol composition in the studied system determines
changes of the rheological properties, suggesting that the PVA acts as
a plasticizer. Consequently, rheological behavior of complex system,
described by the nonlinear flow curve, indicates the impact of
polyvinil alcohol content to polysulfone solution, in order to facilitate
the subsequently preparation of bioactive membranes.
Abstract: In the present study, a numerical approach to describe the pyrolysis of a single solid particle of wood is used to study the influence of various conditions such as particle size, heat transfer coefficient, reactor temperature and heating rate. The influence of these parameters in the change of the duration of the pyrolysis cycle was studied. Mathematical modeling was employed to simulate the heat, mass transfer, and kinetic processes inside the reactor. The evolutions of the mass loss as well as the evolution of temperature inside the thick piece are investigated numerically. The elaborated model was also employed to study the effect of the reactor temperature and the rate of heating on the change of the temperature and the local loss of the mass inside the piece of wood. The obtained results are in good agreement with the experimental data available in the literature.
Abstract: A 15-storey RC building, studied in this paper, is
representative of modern building type constructed in Madina City in
Saudi Arabia before 10 years ago. These buildings are almost
consisting of reinforced concrete skeleton i.e. columns, beams and
flat slab as well as shear walls in the stairs and elevator areas
arranged in the way to have a resistance system for lateral loads
(wind – earthquake loads). In this study, the dynamic properties of
the 15-storey RC building were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Three dimensional pushover analysis (Nonlinear static
analysis) was carried out using SAP2000 software incorporating
inelastic material properties for concrete, infill and steel. The effect
of modeling the building with and without infill walls, on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madina area has been investigated. ATC-
40 capacity and demand spectra are utilized to get the modification
factor (R) for the studied building. The purpose of this analysis is to
evaluate the expected performance of structural systems by
estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results are summarized and discussed.