Abstract: In this report we have discussed the theoretical aspects
of the flow transformation, occurring through a series of bifurcations.
The parameters and their continuous diversion, the intermittent bursts
in the transition zone, variation of velocity and pressure with time,
effect of roughness in turbulent zone, and changes in friction factor
and head loss coefficient as a function of Reynolds number for a
transverse flow across a cylinder have been discussed. An analysis of
the variation in the wake length with Reynolds number was done in
FORTRAN.
Abstract: High Peak to Average Power Ratio (PAPR) of the
transmitted signal is a serious problem in multicarrier systems (MC),
such as Orthogonal Frequency Division Multiplexing (OFDM), or in
Multi-Carrier Code Division Multiple Access (MC-CDMA) systems,
due to large number of subcarriers. This effect is possible reduce with
some PAPR reduction techniques. Spreading sequences at the
presence of Saleh and Rapp models of high power amplifier (HPA)
have big influence on the behavior of system. In this paper we
investigate the bit-error-rate (BER) performance of MC-CDMA
systems. Basically we can see from simulations that the MC-CDMA
system with Iterative algorithm can be providing significantly better
results than the MC-CDMA system. The results of our analyses are
verified via simulation.
Abstract: Iris codes contain bits with different entropy. This
work investigates different strategies to reduce the size of iris
code templates with the aim of reducing storage requirements and
computational demand in the matching process. Besides simple subsampling
schemes, also a binary multi-resolution representation as
used in the JBIG hierarchical coding mode is assessed. We find that
iris code template size can be reduced significantly while maintaining
recognition accuracy. Besides, we propose a two-stage identification
approach, using small-sized iris code templates in a pre-selection
stage, and full resolution templates for final identification, which
shows promising recognition behaviour.
Abstract: The paper deals with the usage of speech acts and
politeness strategies in an EFL classroom in Georgia (Rep of). It
explores the students’ and the teachers’ practice of the politeness
strategies and the speech acts of apology, thanking, request,
compliment / encouragement, command, agreeing / disagreeing,
addressing and code switching. The research method includes
observation as well as a questionnaire. The target group involves the
students from Georgian public schools and two certified, experienced
local English teachers. The analysis is based on Searle’s Speech Act
Theory and Brown and Levinson’s politeness strategies. The findings
show that the students have certain knowledge regarding politeness
yet they fail to apply them in English communication. In addition,
most of the speech acts from the classroom interaction are used by
the teachers and not the students. Thereby, it is suggested that
teachers should cultivate the students’ communicative competence
and attempt to give them opportunities to practise more English
speech acts than they do today.
Abstract: The adsorption efficiency of fired clayey pellets of 5
and 8 mm diameter size for Cu(II) and Zn(II) ion removal from a
waste printing developer was studied. In order to investigate the
influence of contact time, adsorbent mass and pellet size on the
adsorption efficiency the batch mode was carried out. Faster uptake
of copper ion was obtained with the fired clay pellets of 5 mm
diameter size within 30 minutes. The pellets of 8 mm diameter size
showed the higher equilibrium time (60 to 75 minutes) for copper and
zinc ion. The results pointed out that adsorption efficiency increases
with the increase of adsorbent mass. The maximal efficiency is
different for Cu(II) and Zn(II) ion due to the pellet size. Therefore,
the fired clay pellets of 5 mm diameter size present an effective
adsorbent for Cu(II) ion removal (adsorption efficiency is 63.6%),
whereas the fired clay pellets of 8 mm diameter size are the best
alternative for Zn(II) ion removal (adsorption efficiency is 92.8%)
from a waste printing developer.
Abstract: Background: With the perceived pain and poor
function experienced following knee arthroplasty, patients usually
feel un-satisfied. Yet, a controversy still persists on the appropriate
operative technique that doesn’t affect proprioception much.
Purpose: This study compared the effects of Cruciate Retaining
(CR) and Posterior Stabilized (PS) total knee arthroplasty (TKA on
dynamic balance, pain and functional performance following
rehabilitation.
Methods: Thirty patients with CRTKA (group I), thirty with
PSTKA (group II) and fifteen indicated for arthroplasty but weren’t
operated on yet (group III) participated in the study. The mean age
was 54.53±3.44, 55.13±3.48 and 55.33±2.32 years and BMI
35.7±3.03, 35.7±1.99 and 35.73±1.03 kg/m2 for groups I, II and III
respectively. The Berg Balance Scale (BBS), WOMAC pain subscale
and Timed Up-and-Go (TUG) and Stair-Climbing (SC) tests were
used for assessment. Assessments were conducted four weeks preand
post-operatively, three, six and twelve months post-operatively
with the control group being assessed at the same time intervals. The
post-operative rehabilitation involved hospitalization (1st week),
home-based (2nd-4th weeks), and outpatient clinic (5th-12th weeks)
programs, follow-up to all groups for twelve months.
Results: The Mixed design MANOVA revealed that group I had
significantly lower pain scores and SC time compared with group II
three, six and twelve months post-operatively. Moreover, the BBS
scores increased significantly and the pain scores and TUG and SC
time decreased significantly six months post-operatively compared
with four weeks pre- and post-operatively and three months postoperatively
in groups I and II with the opposite being true four weeks
post-operatively. But no significant differences in BBS scores, pain
scores and TUG and SC time between six and twelve months postoperatively
in groups I and II.
Interpretation/Conclusion: CRTKA is preferable to PSTKA,
possibly due to the preserved human proprioceptors in the un-excised
PCL.
Abstract: Kazakhstan is currently one of the dynamically
developing states in its region. The stable growth in all sectors of the
economy leads to a corresponding increase in energy consumption.
Thus country consumes significant amount of energy due to the high
level of industrialisation and the presence of energy-intensive
manufacturing such as mining and metallurgy which in turn leads to
low energy efficiency. With allowance for this the Government has
set several priorities to adopt a transition of Republic of Kazakhstan
to a “green economy”. This article provides an overview of
Kazakhstan’s energy efficiency situation in for the period of 1991-
2014. First, the dynamics of production and consumption of
conventional energy resources are given. Second, the potential of
renewable energy sources is summarised followed by the description
of GHG emissions trends in the country. Third, Kazakhstan’ national
initiatives, policies and locally implemented projects in the field of
energy efficiency are described.
Abstract: Recent research in neural networks science and
neuroscience for modeling complex time series data and statistical
learning has focused mostly on learning from high input space and
signals. Local linear models are a strong choice for modeling local
nonlinearity in data series. Locally weighted projection regression is
a flexible and powerful algorithm for nonlinear approximation in
high dimensional signal spaces. In this paper, different learning
scenario of one and two dimensional data series with different
distributions are investigated for simulation and further noise is
inputted to data distribution for making different disordered
distribution in time series data and for evaluation of algorithm in
locality prediction of nonlinearity. Then, the performance of this
algorithm is simulated and also when the distribution of data is high
or when the number of data is less the sensitivity of this approach to
data distribution and influence of important parameter of local
validity in this algorithm with different data distribution is explained.
Abstract: In this study, composites were fabricated from oil
palm empty fruit bunch fiber and poly(lactic) acid by extrusion
followed by injection moulding. Surface of the fiber was pre-treated
by ultrasound in an alkali medium and treatment efficiency was
investigated by scanning electron microscopy (SEM) analysis and
Fourier transforms infrared spectrometer (FTIR). Effect of fiber
treatment on composite was characterized by tensile strength (TS),
tensile modulus (TM) and impact strength (IS). Furthermore,
biostrong impact modifier was incorporated into the treated fiber
composite to improve its impact properties. Mechanical testing
showed an improvement of up to 23.5% and 33.6% respectively for
TS and TM of treated fiber composite above untreated fiber
composite. On the other hand incorporation of impact modifier led to
enhancement of about 20% above the initial IS of the treated fiber
composite.
Abstract: The current study investigated the influence of milling
time and ball-to-powder (BPR) weight ratio on the microstructural
constituents and mechanical properties of bulk nanocrystalline Al;
Al-10%Cu; and Al-10%Cu-5%Ti alloys. Powder consolidation was
carried out using a high frequency induction heat sintering where the
processed metal powders were sintered into a dense and strong bulk
material. The powders and the bulk samples were characterized using
XRD and FEGSEM techniques. The mechanical properties were
evaluated at various temperatures of 25°C, 100°C, 200°C, 300°C and
400°C to study the thermal stability of the processed alloys. The
processed bulk nanocrystalline alloys displayed extremely high
hardness values even at elevated temperatures. The Al-10%Cu-5%Ti
alloy displayed the highest hardness values at room and elevated
temperatures which are related to the presence of Ti-containing
phases such as Al3Ti and AlCu2Ti. These phases are thermally stable
and retain the high hardness values at elevated temperatures up to
400ºC.
Abstract: The present study was undertaken to investigate the
effect of pre-aging and aging parameters (time and temperature) on
the mechanical properties of Al-Mg-Zn (7075) alloys. Ultimate
tensile strength, 0.5% offset yield strength and % elongation
measurements were carried out on specimens prepared from cast and
heat treated 7075 alloys. Aging treatments were carried out for the as
solution treated (SHT) specimens (after quenching in warm water).
The specimens were aged at different conditions; Natural aging was
carried out at room temperature for different periods of time. Double
aging was performed for SHT conditions (pre-aged at different time
and temperature followed by high temperature aging). Ultimate
tensile strength, yield strength and % elongation as a function of
different pre-aging and aging parameters are analyzed to acquire an
understanding of the effects of these variables and their interactions
on the mechanical properties of Be-treated 7075 alloys.
Abstract: The continuous decline of petroleum and natural gas
reserves and non linear rise of oil price has brought about a
realisation of the need for a change in our perpetual dependence on
the fossil fuel. A day to day increased consumption of crude and
petroleum products has made a considerable impact on our foreign
exchange reserves. Hence, an alternate resource for the conversion of
energy (both liquid and gas) is essential for the substitution of
conventional fuels. Biomass is the alternate solution for the present
scenario. Biomass can be converted into both liquid as well as
gaseous fuels and other feedstocks for the industries.
Abstract: The mechanics of rip currents are complex, involving
interactions between waves, currents, water levels and the bathymetry,
that present particular challenges for numerical models. Here,
the effects of a grid-spacing dependent horizontal mixing on the
wave-current interactions are studied. Near the shore, wave rays
diverge from channels towards bar crests because of refraction by
topography and currents, in a way that depends on the rip current
intensity which is itself modulated by the horizontal mixing. At
low resolution with the grid-spacing dependent horizontal mixing,
the wave motion is the same for both coupling modes because the
wave deviation by the currents is weak. In high resolution case,
however, classical results are found with the stabilizing effect of
the flow by feedback of waves on currents. Lastly, wave-current
interactions and the horizontal mixing strongly affect the intensity
of the three-dimensional rip velocity.
Abstract: Physics Education Research (PER) results have shown
that students do not achieve the expected level of competency in
understanding the concepts of different domains of Physics learning
when taught by the traditional teaching methods, the concepts of
Electricity and Magnetism (E&M) being one among them.
Simulation being one of the valuable instructional tools renders an
opportunity to visualize varied experiences with such concepts.
Considering the electric force concept which requires extensive use
of vector representations, we report here the outcome of the research
results pertaining to the student understanding of this concept and the
role of simulation in using vector representation. The simulation
platform provides a positive impact on the use of vector
representation.
The first stage of this study involves eliciting and analyzing
student responses to questions that probe their understanding of the
concept of electrostatic force and this is followed by four stages of
student interviews as they use the interactive simulations of electric
force in one dimension. Student responses to the questions are
recorded in real time using electronic pad. A validation test interview
is conducted to evaluate students' understanding of the electric force
concept after using interactive simulation. Results indicate lack of
procedural knowledge of the vector representation. The study
emphasizes the need for the choice of appropriate simulation and
mode of induction for learning.
Abstract: Conventional educational practices, do not offer all
the required skills for teachers to successfully survive in today’s
workplace. Due to poor professional training, a big gap exists across
the curriculum plan and the teacher practices in the classroom. As
such, raising the quality of teaching through ICT-enabled training and
professional development of teachers should be an urgent priority.
‘Mobile Learning’, in that vein, is an increasingly growing field of
educational research and practice across schools and work places. In
this paper, we propose a novel Mobile learning system that allows the
users to learn through an intelligent mobile learning in cooperatively
every-time and every-where. The system will reduce the training cost
and increase consistency, efficiency, and data reliability. To establish
that our system will display neither functional nor performance
failure, the evaluation strategy is based on formal observation of
users interacting with system followed by questionnaires and
structured interviews.
Abstract: The prepreg process among the CFRP (Carbon Fiber
Reinforced Plastic) forming methods is the short term of
‘Pre-impregnation’, which is widely used for aerospace composites
that require a high quality property such as a fiber-reinforced woven
fabric, in which an epoxy hardening resin is impregnated the reality.
However, that this process requires continuous researches and
developments for its commercialization because the delamination
characteristically develops between the layers when a great weight is
loaded from outside to supplement such demerit, three lamination
methods among the prepreg lamination methods of CFRP were
designed to minimize the delamination between the layers due to
external impacts. Further, the newly designed methods and the
existing lamination methods were analyzed through a mechanical
characteristic test, Interlaminar Shear Strength test. The Interlaminar
Shear Strength test result confirmed that the newly proposed three
lamination methods, i.e. the Roll, Half and Zigzag laminations,
presented more excellent strengths compared to the conventional Ply
lamination. The interlaminar shear strength in the roll method with
relatively dense fiber distribution was approximately 1.75% higher
than that in the existing ply lamination method, and in the half method,
it was approximately 0.78% higher.
Abstract: In this paper, the electromagnetic shielding
characteristics of an up-to-date typical carbon filler material, carbon
fiber used with a metal mesh were investigated. Carbon fiber
12k-prepregs, where carbon fibers were impregnated with epoxy, were
laminated with wire meshes, vacuum bag-molded and hardened to
manufacture hybrid-type specimens, with which an electromagnetic
shield test was performed in accordance with ASTM D4935-10,
through which was known as the most excellent reproducibility is
obtainable among electromagnetic shield tests. In addition, glass fiber
prepregs whose electromagnetic shielding effect were known as
insignificant were laminated and formed with wire meshes to verify
the validity of the electromagnetic shield effect of wire meshes in
order to confirm the electromagnetic shielding effect of metal meshes
corresponding existing carbon fiber 12k-prepregs. By grafting carbon
fibers, on which studies are being actively underway in the
environmental aspects and electromagnetic shielding effect, with
hybrid-type wire meshes that were analysed through the tests, in this
study, the applicability and possibility are proposed.
Abstract: Fracture in hot precision forging of engine valves was
investigated in this paper. The entire valve forging procedure was
described and the possible cause of the fracture was proposed. Finite
Element simulation was conducted for the forging process, with
commercial Finite Element code DEFORMTM. The effects of
material properties, the effect of strain rate and temperature were
considered in the FE simulation. Two fracture criteria were discussed
and compared, based on the accuracy and reliability of the FE
simulation results. The selected criterion predicted the fracture
location and shows the trend of damage increasing with good
accuracy, which matches the experimental observation. Additional
modification of the punch shapes was proposed to further reduce the
tendency of fracture in forging. Finite Element comparison shows a
great potential of such application in the mass production.
Abstract: The absorption power generation cycle based on the
ammonia-water mixture has attracted much attention for efficient
recovery of low-grade energy sources. In this paper a thermodynamic
performance analysis is carried out for a Kalina cycle using
ammonia-water mixture as a working fluid for efficient conversion of
low-temperature heat source in the form of sensible energy. The
effects of the source temperature on the system performance are
extensively investigated by using the thermodynamic models. The
results show that the source temperature as well as the ammonia mass
fraction affects greatly on the thermodynamic performance of the
cycle.
Abstract: Water flow management is one of the most important
parts of river engineering. Non-uniformity distribution of rainfall and
various flow demand with unreasonable flow management will be
caused destroyed of river ecosystem. Then, it is very serious to
determine ecosystem flow requirement. In this paper, Flow duration
curve indices method which has hydrological based was used to
evaluate environmental flow in Gharasou River, Ardabil, Iran. Using
flow duration curve, Q90 and Q95 for different return periods were
calculated. Their magnitude were determined as 1-day, 3-day, 7-day
and 30 day. According the second method, hydraulic alteration
indices often had low and medium range. In order to maintain river at
an acceptable ecological condition, minimum daily discharge of
index Q95 is 0.7 m3.s-1.