Abstract: Some regularities of formation of a new structural
state of the thermoplastic polymers - gradually oriented (stretched)
state (GOS) are discussed. Transition into GOS is realized by the
graded oriented stretching - by action of inhomogeneous mechanical
field on the isotropic linear polymers or by zone stretching that is
implemented on a standard tensile-testing machine with using a
specially designed zone stretching device (ZSD). Both technical
approaches (especially zone stretching method) allows to manage the
such quantitative parameters of gradually oriented polymers as a
range of change in relative elongation/orientation degree, length of
this change and profile (linear, hyperbolic, parabolic, logarithmic,
etc.). The possibility of obtaining functionally graded materials
(FGMs) by graded orientation method is briefly discussed. Uniaxial
graded stretching method should be considered as an effective
technological solution to create polymer materials with a
predetermined gradient of physical properties.
Abstract: At certain depths during large diameter displacement
pile driving, rebound well over 0.25 inches was experienced,
followed by a small permanent-set during each hammer blow. High
pile rebound (HPR) soils may stop the pile driving and results in a
limited pile capacity. In some cases, rebound leads to pile damage,
delaying the construction project, and the requiring foundations
redesign. HPR was evaluated at seven Florida sites, during driving of
square precast, prestressed concrete piles driven into saturated, fine
silty to clayey sands and sandy clays. Pile Driving Analyzer (PDA)
deflection versus time data recorded during installation, was used to
develop correlations between cone penetrometer (CPT) pore-water
pressures, pile displacements and rebound. At five sites where piles
experienced excessive HPR with minimal set, the pore pressure
yielded very high positive values of greater than 20 tsf. However, at
the site where the pile rebounded, followed by an acceptable
permanent-set, the measured pore pressure ranged between 5 and 20
tsf. The pore pressure exhibited values of less than 5 tsf at the site
where no rebound was noticed. In summary, direct correlations
between CPTu pore pressure and rebound were produced, allowing
identification of soils that produce HPR.
Abstract: In Brazil, neonatal mortality rate is considered
incompatible with the country development conditions, and has been
a Public Health concern. Reduction in infant mortality rates has also
been part of the Millennium Development Goals, a commitment
made by countries, members of the Organization of United Nations
(OUN), including Brazil. Fetal mortality rate is considered a highly
sensitive indicator of health care quality. Suitable actions, such as
good quality and access to health services may contribute positively
towards reduction in these fetal and neonatal rates. With appropriate
antenatal follow-up and health care during gestation and delivery,
some death causes could be reduced or even prevented by means of
early diagnosis and intervention, as well as changes in risk factors
and interventions. Objectives: To study the quality of maternal and
infant health care based on fetal and neonatal mortality, as well as the
possible actions to prevent those deaths in Botucatu (Brazil).
Methods: Classification of prevention according to the International
Classification of Diseases and the modified Wigglesworth´s
classification. In order to evaluate adequacy, indicators of quality of
antenatal and delivery care were established by the authors. Results:
Considering fetal deaths, 56.7% of them occurred before delivery,
which reveals possible shortcomings in antenatal care, and 38.2% of
them were a result of intra- labor changes, which could be prevented
or reduced by adequate obstetric management. These findings were
different from those in the group of early neonatal deaths which were
also studied. Adequacy of health services showed that antenatal and
childbirth care was appropriate for 24% and 33.3% of pregnant
women, respectively, which corroborates the results of prevention.
These results revealed that shortcomings in obstetric and antenatal
care could be the causes of deaths in the study. Early and late
neonatal deaths have similar characteristics: 76% could be prevented
or reduced mainly by adequate newborn care (52.9%) and adequate
health care for gestational women (11.7%). When adequacy of care
was evaluated, childbirth and newborn care was adequate in 25.8%
and antenatal care was adequate in 16.1%. In conclusion, direct
relationship was found between adequacy and quality of care
rendered to pregnant women and newborns, and fetal and infant
mortality. Moreover, our findings highlight that deaths could be
prevented by an adequate obstetric and neonatal management.
Abstract: Chemotherapy and radiotherapy are one of the major
treatment modalities that play important role in the management of a
number of different cancers. This study for the first time evaluates the
toxicity of these treatment modalities and its impact on quality of life
of cancer patients in Pakistan. The study also for the first time
determines what cancer patients of different ages and cancer stages
believe would be an effective intervention to manage their
psychosocial needs and treatment induced toxicity. The article also
provides evidence based approach for the use of variety of
interventions to mange cancer treatment induced morbidity and
toxicity. In light of the present study and reviewed research data,
evidence based recommendations are also made for selection of
appropriate interventions to manage Pain, Nausea and Vomiting,
Anxiety and Depression, Fatigue and Overall QOL of cancer
survivors.
Abstract: The aim of this study was to design and simulate a
particular type of Asynchronous State Machine (ASM), namely a
‘traffic light controller’ (TLC), operated at a frequency of 0.5 Hz.
The design task involved two main stages: firstly, designing a 4-bit
binary counter using J-K flip flops as the timing signal and,
subsequently, attaining the digital logic by deploying ASM design
process. The TLC was designed such that it showed a sequence of
three different colours, i.e. red, yellow and green, corresponding to
set thresholds by deploying the least number of AND, OR and NOT
gates possible. The software Multisim was deployed to design such
circuit and simulate it for circuit troubleshooting in order for it to
display the output sequence of the three different colours on the
traffic light in the correct order. A clock signal, an asynchronous 4-
bit binary counter that was designed through the use of J-K flip flops
along with an ASM were used to complete this sequence, which was
programmed to be repeated indefinitely. Eventually, the circuit was
debugged and optimized, thus displaying the correct waveforms of
the three outputs through the logic analyser. However, hazards
occurred when the frequency was increased to 10 MHz. This was
attributed to delays in the feedback being too high.
Abstract: In and around Erode District, it is estimated that more
than 1250 chemical and allied textile processing fabric industries are
affected, partially closed and shut off for various reasons such as poor
management, poor supplier performance, lack of planning for
productivity, fluctuation of output, poor investment, waste analysis,
labor problems, capital/labor ratio, accumulation of stocks, poor
maintenance of resources, deficiencies in the quality of fabric, low
capacity utilization, age of plant and equipment, high investment and
input but low throughput, poor research and development, lack of
energy, workers’ fear of loss of jobs, work force mix and work ethic.
The main objective of this work is to analyze the existing conditions
in textile fabric sector, validate the break even of Total Productivity
(TP), analyze, design and implement fuzzy sets and mathematical
programming for improvement of productivity and quality
dimensions in the fabric processing industry. It needs to be
compatible with the reality of textile and fabric processing industries.
The highly risk events from productivity and quality dimension were
found by fuzzy systems and results are wrapped up among the textile
fabric processing industry.
Abstract: Leukaemia is a blood cancer disease that contributes
to the increment of mortality rate in Malaysia each year. There are
two main categories for leukaemia, which are acute and chronic
leukaemia. The production and development of acute leukaemia cells
occurs rapidly and uncontrollable. Therefore, if the identification of
acute leukaemia cells could be done fast and effectively, proper
treatment and medicine could be delivered. Due to the requirement of
prompt and accurate diagnosis of leukaemia, the current study has
proposed unsupervised pixel segmentation based on clustering
algorithm in order to obtain a fully segmented abnormal white blood
cell (blast) in acute leukaemia image. In order to obtain the
segmented blast, the current study proposed three clustering
algorithms which are k-means, fuzzy c-means and moving k-means
algorithms have been applied on the saturation component image.
Then, median filter and seeded region growing area extraction
algorithms have been applied, to smooth the region of segmented
blast and to remove the large unwanted regions from the image,
respectively. Comparisons among the three clustering algorithms are
made in order to measure the performance of each clustering
algorithm on segmenting the blast area. Based on the good sensitivity
value that has been obtained, the results indicate that moving kmeans
clustering algorithm has successfully produced the fully
segmented blast region in acute leukaemia image. Hence, indicating
that the resultant images could be helpful to haematologists for
further analysis of acute leukaemia.
Abstract: Assembly line balancing problem is aimed to divide
the tasks among the stations in assembly lines and optimize some
objectives. In assembly lines the workload on stations is different
from each other due to different tasks times and the difference in
workloads between stations can cause blockage or starvation in some
stations in assembly lines. Buffers are used to store the semi-finished
parts between the stations and can help to smooth the assembly
production. The assembly line balancing and buffer sizing problem
can affect the throughput of the assembly lines. Assembly line
balancing and buffer sizing problems have been studied separately in
literature and due to their collective contribution in throughput rate of
assembly lines, balancing and buffer sizing problem are desired to
study simultaneously and therefore they are considered concurrently
in current research. Current research is aimed to maximize
throughput, minimize total size of buffers in assembly line and
minimize workload variations in assembly line simultaneously. A
multi objective optimization objective is designed which can give
better Pareto solutions from the Pareto front and a simple example
problem is solved for assembly line balancing and buffer sizing
simultaneously. Current research is significant for assembly line
balancing research and it can be significant to introduce optimization
approaches which can optimize current multi objective problem in
future.
Abstract: Code- mixing in spontaneous speech has been widely
discussed, but not in virtual situations; especially in context of the
third language learning students. Thus, this study is an attempt to
explore the linguistic characteristics of the mixing of Japanese,
English and Thai in a mobile Line chat room by students with their
background of English as L2, Japanese as L3 and Thai as mother
tongue. The result found that insertion of Thai content words is a very
common linguistic phenomenon embedded with the other two
languages in the sentences. As chatting is to be ‘relational’ or
‘interactional’, it affected the style of lexical choices to be speech-like,
more personal and emotionally-related. A personal pronoun in
Japanese is often mixed into the sentences. The Japanese
sentence-final question particle か “ka” was added to the end of the
sentence based on Thai grammar rules. Some unique characteristics
were created while chatting.
Abstract: Prior to quantifying the variables of the information
model for using school terminology in Croatia's region of Dalmatia
from 1884 to 2014, the most relevant model variables had to be
determined: historical circumstances, standard of living, education
system, linguistic situation, and media. The research findings show
that there was no significant transfer of the 1884 school terms into
1949 usage; likewise, the 1949 school terms were not widely used in
2014. On the other hand, the research revealed that the meaning of
school terms changed over the decades. The quantification of the
variables will serve as the groundwork for creating an information
model for using school terminology in Dalmatia from 1884 to 2014
and for defining direct growth rates in further research.
Abstract: Equal channel angular pressing (ECAP) of
commercial Al-Mg-Si alloy was conducted using two strain rates.
The ECAP processing was conducted at room temperature and at
250°C. Route A was adopted up to a total number of four passes in
the present work. Structural evolution of the aluminum alloy discs
was investigated before and after ECAP processing using optical
microscopy (OM). Following ECAP, simple compression tests and
Vicker’s hardness were performed. OM micrographs showed that, the
average grain size of the as-received Al-Mg-Si disc tends to be larger
than the size of the ECAP processed discs. Moreover, significant
difference in the grain morphologies of the as-received and processed
discs was observed. Intensity of deformation was observed via the
alignment of the Al-Mg-Si consolidated particles (grains) in the
direction of shear, which increased with increasing the number of
passes via ECAP. Increasing the number of passes up to 4 resulted in
increasing the grains aspect ratio up to ~5. It was found that the
pressing temperature has a significant influence on the
microstructure, Hv-values, and compressive strength of the processed
discs. Hardness measurements demonstrated that 1-pass resulted in
increase of Hv-value by 42% compared to that of the as-received
alloy. 4-passes of ECAP processing resulted in additional increase in
the Hv-value. A similar trend was observed for the yield and
compressive strength. Experimental data of the Hv-values
demonstrated that there is a lack of any significant dependence on the
processing strain rate.
Abstract: Risperidone (RISP) is an antipsychotic agent and has
low water solubility and nontargeted delivery results in numerous
side effects. Hence, an attempt was made to develop SLNs hydrogel
for intranasal delivery of RISP to achieve maximum bioavailability
and reduction of side effects. RISP loaded SLNs composed of 1.65%
(w/v) lipid mass were produced by high shear homogenization (HSH)
coupled ultrasound (US) method using glycerylmonostearate (GMS)
or Imwitor 900K (solid lipid). The particles were loaded with 0.2%
(w/v) of the RISP & surface-tailored with a 2.02% (w/v) non-ionic
surfactant Tween® 80. Optimization was done using 32 factorial
design using Design Expert® software. The prepared SLNs
dispersion incorporated into Polycarbophil AA1 hydrogel (0.5%
w/v). The final gel formulation was evaluated for entrapment
efficiency, particle size, rheological properties, X ray diffraction, in
vitro diffusion, ex vivo permeation using sheep nasal mucosa and
histopathological studies for nasocilliary toxicity. The entrapment
efficiency of optimized SLNs was found to be 76 ± 2%,
polydispersity index
Abstract: The problem of psychologist training remains a key
priority in Armenia. During the Soviet period, the notion of a
psychologist was obscure not only in Armenia but also in other
Soviet republics. The breakup of the Soviet Union triggered a gradual
change in this area activating the cooperation with specialists from
other countries. The need for recovery from the psychological trauma
caused by the 1988 earthquake pushed forward the development of
practical psychology in Armenia. This phenomenon led to positive
changes in perception of and interest to a psychologist
profession.Armenian universities started designing special programs
for psychologists’ preparation. Armenian psychologists combined
their efforts in the field of training relevant specialists.
During the recent years, the Bologna educational system was
introduced in Armenia which led to implementation of education
quality improvement programs. Nevertheless, even today the issue of
psychologists’ training is not yet settled in Armenian universities. So
far graduate psychologists haven’t got a clear idea of personal and
professional qualities of a psychologist. Recently, as a result of
educational reforms, the psychology curricula underwent changes,
but so far they have not led to a desired outcome. Almost all curricula
in certain specialties are aimed to form professional competencies
and strengthen practical skills.
A survey conducted in Armenia aimed to identify what are the
ideas of young psychology specialists on the image of a psychologist.
The survey respondents were 45 specialists holding bachelor’s degree
as well as 30 master degree graduates, who have not been working
yet. The research reveals that we need to change the approach of
preparing psychology practitioners in the universities of Armenia.
Such an approach to psychologist training will make it possible to
train qualified specialists for enhancement of modern psychology
theory and practice.
Abstract: Shortfall of electrical energy in Pakistan is a challenge
adversely affecting its industrial output and social growth. As
elsewhere, Pakistan derives its electrical energy from a number of
conventional sources. The exhaustion of petroleum and conventional
resources, the rising costs coupled with extremely adverse climatic
effects are taking its toll especially on the under-developed countries
like Pakistan. As alternate, renewable energy sources like hydropower,
solar, wind, even bio-energy and a mix of some or all of them
could provide a credible alternative to the conventional energy
resources that would not only be cleaner but sustainable as well. As a
model, solar energy-based power grid for the near future has been
attempted to offset the energy shortfalls as a mix with our existing
sustainable natural energy resources. An assessment of solar energy
potential for electricity generation is being presented for fulfilling the
energy demands with higher level of reliability and sustainability.
This model is based on the premise that solar energy potential of
Pakistan is not only reliable but also sustainable. This research
estimates the present & future approaching renewable energy
resource specially the impact of solar energy based power grid for
mitigating energy shortage in Pakistan.
Abstract: The research was conducted to empirically validate
the proposed maturity model of e-Government implementation,
composed of four dimensions, further specified by 54 success factors
as attributes. To do so, there are two steps were performed. First,
expert’s judgment was conducted to test its content validity. The
second, reliability study was performed to evaluate inter-rater
agreement by using Fleiss Kappa approach. The kappa statistic
(kappa coefficient) is the most commonly used method for testing the
consistency among raters. Fleiss Kappa was a generalization of
Kappa in extensions to the case of more than two raters (multiple
raters) with multi-categorical ratings. Our findings show that most
attributes of the proposed model were related to their corresponding
dimensions. According to our results, The percentage of agree
answers given by the experts was 73.69% in dimension A, 89.76% in
B, 81.5% in C and 60.37% in D. This means that more than half of
the attributes of each dimensions were appropriate or relevant to the
dimensions they were supposed to measure, while 85% of attributes
were relevant enough to their corresponding dimensions. Inter-rater
reliability coefficient also showed satisfactory result and interpreted
as substantial agreement among raters. Therefore, the proposed
model in this paper was valid and reliable to measure the maturity of
e-Government implementation.
Abstract: The thyroid gland is the largest classic endocrine
organ that effects many organs of the body and plays a significant
role in the process of Metabolism in animals. The aim of this study
was to investigate the prevalence of thyroid disorders diagnosed by
ultrasound and microscopic Lesions of the thyroid during the
slaughter of apparently healthy One Humped Camels (Camelus
dromedarius) in Iran. Randomly, 520 male camels (With an age
range of 4 to 8 years), were studied in 2012 to 2013. The Camels’
thyroid glands were evaluated by sonographic examination. In both
longitudinal and transverse view and then tissue sections were
provide and stained with H & E and finally examined by light
microscopy. The results obtained indicated the following:
hyperplastic goiter (21%), degenerative changes (12%), follicular
cysts (8%), follicular atrophy (4%), nodular hyperplasia (3%),
adenoma (1%), carcinoma (1%) and simple goiter colloid (1%).
Ultrasound evaluation of thyroid gland in adenoma and carcinoma
showed enlargement and irregular of the gland, decreased
echogenicity, and the heterogeneous thyroid parenchyma. Also, in
follicular cysts were observed in the enlarged gland with no echo
structures of different sizes and decreased echogenicity as a local or
general. In nodular hyperplasia, increase echogenicity and
heterogeneous parenchymal were seen. These findings suggest the
use of sonography and pathology as a screening test in the diagnosis
of complications of thyroid disorders.
Abstract: As the current status and growth of Indian automobile
industry is remarkable, transportation sectors are the main concern in
terms of energy security and climate change. Due to rising demand of
fuel and its dependency on foreign countries that affects the GDP of
nation, suggests that penetration of electrical vehicle will increase in
near future. So in this context analysis is done if the 10 percent of
conventional vehicles including cars, three wheelers and two
wheelers becomes electrical vehicles in near future which is also a
part of Nations Electric Mobility Mission Plan then the saving which
improves the nation’s economy is analyzed in detail. Whether the
Indian electricity grid is capable of taking this load with current
generation and demand all over the country is also analyzed in detail.
Current situation of Indian grid is analyzed and how the gap between
generation and demand can be reduced is discussed in terms of
increasing generation capacity and energy conservation measures.
Electrical energy conservation measures in Industry and especially in
rural areas have been analyzed to improve performance of Indian
electricity grid in context of electrical vehicle penetration in near
future. Author was a part of Vishvakarma yojna in which energy
losses were measured in 255 villages of Gujarat and solutions were
suggested to mitigate them and corresponding reports was submitted
to the authorities of Gujarat government.
Abstract: Burnishing is increasingly used as a finishing operation to improve surface roughness and surface hardness. This can be achieved by applying a hard ball or roller onto metallic surfaces under pressure, in order to achieve many advantages in the metallic surface. In the present work, the feed rate, speed and force have been considered as the basic burnishing parameters to study the surface roughness and surface hardness of metallic matrix composites. The considered metal matrix composites were made from Aluminum-Magnesium-Graphite with five different weight percentage of graphite. Both effects of burnishing parameters mentioned above and the graphite percentage on the surface hardness and surface roughness of the metallic matrix composites were studied. The results of this investigation showed that the surface hardness of the metallic composites increases with the increase of the burnishing force and decreases with the increase in the burnishing feed rate and burnishing speed. The surface roughness of the metallic composites decreases with the increasing of the burnishing force, feed rate, and speed to certain values, then it starts to increase. On the other hand, the increase in the weight percentage of the graphite in the considered composites causes a decrease in the surface hardness and an increase in the surface roughness.
Abstract: Reverse Logistics (RL) Network is considered as
complex and dynamic network that involves many stakeholders such
as: suppliers, manufactures, warehouse, retails and costumers, this
complexity is inherent in such process due to lack of perfect
knowledge or conflicting information. Ontologies on the other hand
can be considered as an approach to overcome the problem of sharing
knowledge and communication among the various reverse logistics
partners. In this paper we propose a semantic representation based on
hybrid architecture for building the Ontologies in ascendant way, this
method facilitates the semantic reconciliation between the
heterogeneous information systems that support reverse logistics
processes and product data.
Abstract: Pipe failure and leakage is a problematic issue and the
traditional solution of replacing the pipes is costly and time
consuming. Rehabilitation by relining materials based on polymer
composites is an alternative solution towards the degradation problem
of the old piping. This paper provides a brief summary of advances in
technology, methods and materials for relining as well as a summary
of the degradation analyses of the two main composite materials used
for relining, rubber filled epoxy and reinforced polyester baltoflake
when they are exposed in deionized water and elevated temperature
up to 80°C for a duration of 2-14 months in the laboratory.